We deals in the following Chemicals :- Cementing Additives Bentonite Powder, Bentonite Lumps, Bentonite Granules, Bentonite Clay Quartz / Silica Powder, Quartz / Silica Lumps, Quartz / Silica Granules, Quartz / Silica Grits Mica Powder, Mica Flakes, Mica Blocks, Mica Sheets Dolomite Powder Barite Powder, Barite Ore Hematite / Iron Oxide Powder, Iron Oxide ( Ferric Oxide ) Ilmenite (Synthetic Rutile) Fly Ash Powder Alumina Silica ( Cenosphere ) Powder Calcium Carbonate Powder Magnetite, Cellulose Fibers, Cellophane Flakes, Walnut Shells
Sodium napthaline formaldehyde
Summary 1. Cf410s dispersant can significantly reduce cement slurry consistency, improve liquidity and rheolog- Ical behavior of cement slurry 2. Cf410s dispersantis applicable in a wide temperature range and can be resistant to 356°f (180°c). 3. Cf410s dispersant has salt resistence and still has good performance in 5%-10% brine cement slurry. 4. Cf410s dispersant is suitable for dry mixed as well as water mixed, soluble in cold water. 5. Cf410s dispersant is compatible with cement and other additives well. Special attentions The performance of cf410s dispersant will be obviously decreased when dispersant cf410s is used in brine system, whose concentration is higher than that of the half saturated brine. Applications Temperature:lower than 356°f (180°c) (bhct). Dosage: cf410s dispersant generally 0.2-2.0% (bwoc), recommend amount 0.5% (bwoc).
Product Information: European Based Finest filler & additive G FINE Micro FINE ULTRA FINE EROPEAN BASED FINEST FILLER G FINE is a new generation supplementary cementitious material (SCM) with a built-in high tech content. In spite of its high fineness it does not increase water demand at the dosage range of 5 to 15 percent of normal OPC in general. In fact concrete slump is seen to be improved, due to the dense packing of cementitious material, producing low void content. The use of G FINE results in hydrated cement matrix to comprise of very small pores. G FINE is a specially processed product based on high glass content with high reactivity obtained through the process of controlled granulation. The raw materials are composed primary of low calcium silicates. The processing with other select ingredients results in controlled particle size distribution. G FINE can also be used as a high range water reducer to improve compressive strength or as a super workability aid to improve flow. G FINE can be used as practical substitute for Silica Fume as per the results obtained. If the advantages of G FINE are observed in the concrete mix design, the initial rate of strength development was found to be increased or similar as that of Silica Fume. Where to use G FINE : Residential, roads, airports, commercial building. Producing mass concrete structures and pile. In high-rise structures the concrete is to be pump easily. Low water to binder ration for high performance concrete. Precast concrete element for heavy structures precast units. To improved initial strength and increase faster . Better retention of workability and improved strength gain. Benefits of G FINE : The workability of the mix retention is improved Improve durability and permeability of concrete Increased strength of concrete Reduction in segregation can be observed in the mix Reduction in heat of hydration of the mix Non- toxic , eco friendly cost effective, economical solution G-FINE Packaging: G FINE is available in Bulk Jumbo bags with plastic inner liner. The product is also available in 25kg plastic lined bags. Storage: G FINE when stored correctly has an indefinite shelf life. Like cement, G-FINE must be protected from contamination and moisture. The product can be stored in bulk in a clean, dry storage silo Or warehouse .
Features: 1. Mixed with cement mortar, improving the bonding strength and flexibility 2. Can be used as booster for the interface treatment agent and tile adhesive 3. Improve the anti-infiltration and waterproof function of cement mortar, and make it suitable for the wet area like swimming pool 4. Anti-aging, non-toxic, safety. Surface Treatment: The substrate surface should be firm, dry and clean, no grease, no wax, and other loose materials. Mixed Ratio: 1. For strengthen the bond performance: 50kg cement mortar with 3-5kg additive and appropriate water 2. For outdoor heavy-type ceramic tile adhesive: 5kg mb-01 powder + 1.1kg mb-03 + appropriate water; for indoor heavy-type ceramic tile adhesive: 5kg mb-01 powder + 0.6kg mb-03 + appropriate water; for smooth surface small ceramic tile adhesive: 5kg mb-01 powder + 0.8kg mb0-03 with appropriate water 3. For the interface treatment: 1.0kg mb-01 powder + 0.1kg mb0-03 with appropriate water 4. For the cement mortar leveling: about 2.5kg mb-03 mixed with 50kg cement. Operation Process: 1. The same operation process with mb-01 adhesive when paste various type of tiles and stone materials 2.Cement mortar leveling: according to the above ratio, mixed the mb-03 with cement mortar, then make inserting 3. Interface treatment: for the high water absorption surface, wet the surface at first, then brush the mixed slurry on the surface, control the thickness under 1.5mm, after it dries, doing the paste; for the low water absorption, no wet work, do with the above 4.for the old ceramic tile: a.mixing MB-01 with MB-03 in the rate of 1.1-1.2: 1 for the interface treatment b. after it dries, according to the process using MB-01 to operate directly c. or use MB-01 directly for the old wall retreating. Cautions: 1. The mortar that attached to the surface should be clean before it dry 2. Operating under 5¡æ~40¡æ situation 3. Finished after 24h, can be walked or fill crack 4. For the old surface retreating, clean the loosen or flake ceramic tile at first. Technical Reference: Coverage area(amount). Technical reference 1, for ceramic tile and stone: A, mixed cement about 0.7kg/m2; B, mixed MB-01 0.4-0.6kg/m2; adjust time(20¡æ): about 10min cool time(20¡æ): about 10min 2, for interface treatment: about 0.15kg/m2 when dry, anti-weak acid and oil resistance 3, for cement mortar leveling: about 0.1kg/m2 Improve the cement bonding strength: 80%(14days). Store Method: Store in cool and dry place, unopened product can be saved for one year. 25kg/bag
1. Increasing productivity and improving quality in cement grinding process 2. Saving the production cost and time 3. Anti-coagulation and stable grinding ability 4. Increasing early and long term strength 5. Reduction of CO2 emission and energy cost.
1. Increasing productivity and improving quality in cement grinding process 2. Saving the production cost and time 3. Anti-coagulation and stable grinding ability 4. Increasing early and long term strength 5. Reduction of CO2 emission and energy cost.
SUMMARY 1. Provides fluid loss control in low, normal and high density cement slurries. 2. Applied below temperature of 180â?? (356â??, BHCT) 3. Features with excellent salt tolerance up to salt-saturation, suitable for both fresh and salt water system 4. When applied, cement slurry system is stable with little free fluid. 5. Has no effect of retardation on the cement slurry and ensures fast development of compressive strength of the set cement 6. Features with good fluidity, does not lead to over-dispersing or thickening and no need to add additional dispersant. 7. Compatible well with other additives. 8. Suitable for all API classes of cement. 9. Dry mixed when applied and no water quality is required. 10. Long durability, not easily affected by damp and not prone to agglomeration 11. The following technical data and parameters are of our standard type of CG610S-D. We are capable of catering tailor-made products and services upon receipt of customersâ?? individual requirements . CEMENT SLURRY PRESCRIPTION Cement Slurry Density Recommended Dosage in Fresh Water and Moderate Temperature System Recommended Dosage in 18% Slat Water and Moderate Temperature System Recommended Dosage in 18% Salt Water and High Temperature System STANDARD PACKAGING AND STORAGE 1. Packed in 25kg bag. It can also be packed according to customerâ??s different individual demands. 2. Use within 24 months after production. When expired, lab test should be conducted to confirm the quality before use. 3. Store in ventilated, cool and dry area, avoid exposing to sun and rain. The height of stack should be less than 8 layers.
ICG-1000 is various types of grinding aids are available to meet customer's needs for saving, cost , increasing productivity and improving quality in cement grinding.
This additive is applied into oilfield cementing operation.Provides fluid loss control in low, normal and high density cement slurries. Applied below temperature of 180â??(356â??, bhct). Mixed with water when applied and no water quality is required. Generally, for moderate temp. 0.9%(mwoc)in fresh water, 1.25%(bwoc)in 18% salt water, for high temp. 18% salt water 2.5%(bwoc) Rachel hua | global service manager
