We are a supplier of used and new Heidelberg printing machine, parts and consumables globally , we acknowledge the demand of offset products and we want to fill that gap by bringing to the world the best affordable quality offset products.
Supplier: Cast iron skulls, cast iron borings and turnings, steels skulls, eaf skulls, plate iron, mill scale, metal scrap, incinerated scrap (e46)
We are glad to propose 500 MT of stain less steel mill scale. Mill scale is formed on the outer surfaces during by the hot rolling lamination of stainless-steel products. At a visual inspection the material is a hard brittle sand and is mainly composed of iron oxides, mostly ferric, and is bluish black in colour, but it also contains considerable alloying elements such as chromium and nickel. The recovery ratio after melting in furnace for the most valuable alloy elements is: - Ni: 3.5 - 4.5% - Cr: 6-8% From the chemical and physical analysis performed on the scrap, and according to the European environmental rules, the material has been classified as a special non dangerous waste, listed in green list. In particular the mill scale can be classified as follows: Waste code: 10 02 10 The material is stored on cemented flooring, and it can be loaded loose in tipper trucks or containers. Chemical analysis of the material is available on request.
We offer 200 tons per month of tire wire scrap from combustion of used tires. Material has no rubber left. Tire wire is loaded loose in 20' containers (28 tons each).
The Incinerated scrap or E46, is the by-product derived from the reprocessing of incinerated domestic waste. After the combustion process, the furnace output (IBA Incinerator bottom ash) is firstly washed, magnetically separated and screened to separate any no ferrous material. At a visual inspection, the material is fragmentized, with iron and steel parts, resulting partly cut or in shredded form. The stock appears heterogeneous and contains all kind of cut or dismantled steel parts such as sheets, bars, frames, wires, bolts and other iron/steel household residues. The incinerated scrap is eventually oxidized, due to the thermal and cooling treatments, that the material has been submitted to. The burnt scrap also contains minor slag parts, ash and iron oxide, due to the recovery process. Such components are inherent and adhere to the scrap surface. The total impurities, can be sorted, but not fully removed. The consignment does not contain any type of arms, ammunition, mines, shells, cartridges, radioactive contaminated, or any other explosive material in any form either used or otherwise. The collected stock, is stored in open air, on cemented flooring. It can be loaded loose in 20â?? heavy duty container. Please feel free to contact us for further details.
We Provide Tmt Brand or Private Logo All Type of Cnc Machines as Below 1. Horigantal Turning Centre 2. Verticle Turning Centre 3. Vertical Machining Centre 4. Spm for Special Type of Activity 5. Double Coloumn Vmc 6. Grinding Machines 7. All Type of Industrial Machines
Ferrite Magnet is manufactured from oxide material by powder metallurgical process. Its advantages include: low-cost excellent corrosion resistance, resistance to be demagnetized etc. The normal working temperature of Ferrite Magnet is between-40C and +250C.It can be magnetized before or after assembling. Generally, Ferrite Magnet can be machined to regular shapes like segments, blocks, rings and discs etc. The normal grades for sintered Ferrite Magnets are Y10,TY25, Y30, Y30BH, Y35, etc. Advantages of Ferrite Magnet: Ferrites have isotropic characteristics, weak magnetic performance, has the same magnetic performance in any direction, multipolar magnetic charge. The main raw material of ferrite is oxides, so it is not corroded by high temperature, high humidity or chemicals (except strong acid and base); with excellent diamagnetic impedance, no flux loss before and after assembly and magnetic charging; working temperature is-40C to + 250C, poor temperature coefficient; Br temperature coefficient is-0.2% /C, 0.2% under Br, etc. per 1 Cincrease; high hardness, wire cutting and grinding; ferrite is brittle and fragile during production and transportation. magnetic requirements and good for strict working environment requirement.
AINiCo is composed primarily of Aluminum Nickel Cobalt and also Copper and Titanium. They are manufactured through either casting or sintering process. Cast AINiCo may be manufactured in complex shapes such as horseshoes not possible with other magnet materials. Sintered AINiCo offer slightly lower magnetic properties but better mechanical characteristics. it can be efficiently magnetized in any direction, and for anisotropic AINiComagnet, it generally has greater magnetic capacitive in a preferred orientation than isotropic types. AINiCo is hard and brittle, Machining or drilling cannot therefore be accomplished by ordinary methods. Holes are usually cored in at the foundry, and magnets are cast close to final size and then finish machined to closer tolerances. â?¢ Advantages of AlNiCo Magnet: 1.Customized designs are available. 2.Max working temperature can be as high as 550�°C. 3.Disadvantage: Br and BH(max)are not as high as rare earth magnet. 4.High energies and relatively low coercivity. 5.High magnetic flux density; low mold charge stable temperature properties; easy to shap.
Samarium Cobalt (SmCo) magnets are made by a sintering process and exist in two forms. The first is Sm1Co5(SmCo 1:5),which has a maximum energy product of between 14 and 24MGOe. The second and more common form is Sm2Co17(SmCo 2:17) which has a maximum energy product of between 22 and 32 MGOe. The main Sm2Co17 alloy is around 35% Samarium (Sm)and 60% Cobalt (Co)with the balance being from varying amounts of lron (Fe) Copper (Cu). Hafnium (Hf) and Zirconium (Zr). Praseodymium (Pr) may also be used. Sm1Co5 is made of only Sm and Co and has excellent corrosion resistance. â?¢ Advantages of SmCo Magnet: 1.Superior resistance to high temperature. 2. Excellent resistance to corrosion, no coating is needed for surface protecting. 3.High working temperature. 4.SmCo is suitable for machines with high magnetic requirements and good for strict working environment requirement.
Ethanol Alcohol Making Machine Equipment/plant,ethanol alcohol equipment ,ethanol alcohol plant, pharmaceutical medical ethanol alcohol plant/process line /equipment /machine /turnkey project /customized ,competitive price good quality ,welcome cooperate! From design -manufacture -installation -traning ,capacity 2000L-600000L/day. Material : starch product ,sugar product ,grain ,and so on . Exported Brazil, Argentina,Korea,Thailand ,Vietnam, Myanmar and so on .
