Brief introduction: Bag filter is a kind of dry dust filtration device. Our company can provide design, manufacture, and installation one-stop service for bag filter. Our product range mainly include bag filter, single bag filter, pulse bag filter, mechanical reverse air bag filter, wet bag filter and bag filter parts. Application: Electricity, metallurgy, chemicals, building materials, paper and other industries. Features and advantages: 1. Reliable design ensures the bag filter stable and long-term operation with the other main equipment and little maintenance. 2. Optimized duct design will be in favor of uniform air distribution. 3. Air leakage prevention design ensures the lowest air leak rate for the bag filter. 4. Steel sub-structure design, which would be easy for transport and installation of the equipment. 5 .Low operating costs. Optimized design of process parameters is conducive to efficient and stable operation of the bag filter with low resistance, reducing energy consumption, as well as the loss of the bag
As an advanced flue gas treatment technology, the Biomass Boiler Wet-type Dust Removal Equipment has the characteristics of simple structure, basic maintenance-free, low operation cost, good ability to remove fine smoke and dust, and achieve the removal of multiple pollutants at the same time.It is especially suitable for the smoke and dust treatment of the special biomass boilers such as wood chips, bamboo chips and bagasse, and has incomparable advantages in reliability and dust removal efficiency.Biomass Boiler Wet-type Dust Removal Equipment is mainly installed in the wet saturated flue gas as the final fine treatment environmental protection equipment. Its dust removal performance has nothing to do with the characteristics of fuel dust. It can effectively capture and collect fine particulate matter, and the dust concentration of outlet can be less than 30mg/Nm3. Biomass Boiler Wet-type Dust Removal Equipment has the advantages of no secondary dust, high dust removal efficiency, small pressure loss, no moving parts, without basic maintenance, compact structure and small occupation area.In recent years, the effect of Wet-type electrostatic precipitator in ultra-low emission and PM2.5 control has been unanimously recognized by industry experts, and its application field is extending from the power industry to other non-power industries.It is especially suitable for the smoke and dust treatment of the special biomass boilers such as wood chips, bamboo chips and bagasse, and has incomparable advantages in reliability and dust removal efficiency.
Bag filter, cyclone, long bag pulse filter, stand-alone filter, high temperature and low pressure long bag pulse filter, electrostatic precipitator.
Bag filter is a kind of dry dust filtration device. Our company can provide design, manufacture, and installation one-stop service for bag filter. Our product range mainly include bag filter, single bag filter, pulse bag filter, mechanical reverse air bag filter, wet bag filter and bag filter parts. Application of Bag Filter: Electric power, metallurgy, chemical and building materials industry Structure: Bag filter is consist of holder, ash bucket, the middle cabinet, the upper part cabinet, bag, frame, jet cleaning device and PLC control procedures and other components. The middle cabinet has sub-chamber structure. Dusty gas goes through collecting tube achieving to each ash bucket. OUR ADVANTAGE: 1. Reliable design ensures the bag filter stable and long-term operation with the other main equipment and little maintenance. 2. Optimized duct design will be in favor of uniform air distribution. 3. Air leakage prevention design ensures the lowest air leak rate for the bag filter. 4. Steel sub-structure design, which would be easy for transport and installation of the equipment. 5. Low operating costs. Optimized design of process parameters is conducive to efficient and stable operation of the bag filter with low resistance, reducing energy consumption, as well as the loss of the bag.
Bag dump stations (also known as manual dumping stations) collect dust generated when dumping powder and bulk solids from bags, boxes, drums, and other containers, and return the material to the hopper.
Bag dump stations (also known as manual dumping stations) collect dust generated when dumping powder and bulk solids from bags, boxes, drums, and other containers, and return the material to the hopper. The system reduces material waste and eliminates the need to clean a remote dust collection site, while protecting workers and preventing plant contamination.
ZL series Long Bag Pulse Dust Collector is a new type and high efficient bag filter that develops from the common short bag fpulse bag filter. It has the features like bigger air volume, stronger dust cleaning ability, high efficiency, easy operation and maintenance and etc. It is suitable for dusty air cleaning and maerial dust collecting in the industries like metallurgy, construction, chemical and etc. Application of Bag Pulse Dust Collector: It is suitable for dusty air cleaning and maerial dust collecting in the industries like metallurgy, construction, chemical and etc. Structure ZL series Long Bag Pulse dust collector is mainly composed of upper box, middle box, ash bucket, supporting legs, filtering bag and blowing device, ash discharging device. The features of this structure are: 1. Upper box is devided into thousands chambers. In order to realize off-line cleanign dust and maintenance, each chamber has equipment 1 lifting valve. 2. Pneumatic vent valve is controlled by air cylinder. The advantages are realiable operation, fast speed of on/off, without any leakage of air. 3. Compared with horizontal installation, the vertical installation fo pneumatic vent valve is easier during maintenance. 4. Filtering bag is self-locked and sealed on the board holes by the flexible ring on the bag. This can gurantee low emission density and easy for installation and replacement. 5. Optimized injection short tube can gurantee perfect dusting cleaning performance. 6. Safety guard and walking platform are equipped for regular maintenance. OUR ADVANTAGE 1. Advanced thin type lifting valve and off-line dust cleaning device can gurantee to collect the dust completely. 2. Reasonable design for air inlet evenly flow tube and dust hopper discharging device. This can resolve the problem the uneven air flow of each chamber. 3. Bigger volume air bag can be suitable for both high pressure and low pressure air supply. 4. Spring increase type is adopted on the top of filtering bag. It has the advanages like good sealing performance, easy and fast bag replacing, bag replacing outside the bag filter. 5. Design of filtering bag is different according to different industry and application. The fabrication standards are increased at approx. 50% based on the industry standard. 6. Solenoid pulse vale adpots high quality raw materia. Its mebrane has longer using life. 7. Control system adpots advanded controller. It has 3 controlling methods: pressure difference, timing and manual. Offline valve, pulse valve and ash discharging valve are auotmatically controlled by the system.
Bag Dust Collectors bag dust collectors Detailed instructions Bag filter is a kind of dry filter. It is suitable for small, dry, non-fibrous dust. Filter bag used textile filter cloth or non textile mat is made, using the fabric filter effect of dust filters, gas when dusty gas into the bag filter, large particles, major dust, due to the effect of gravity settling down, fall into the hopper, contains the fine dust of gas through the filter material, the dust were blocked, the purified gas. Bag filter is a kind of dry filter. Filter material to use after a period of time, due to the screen, collision, stranding, diffusion, electrostatic effect, such as a layer of dust accumulation on the surface of filter bag, at the beginning of the dust layer is called layer, after the movement process, early become the main filter to filter material layer, depending on the role of the first layer, large mesh filter material can also get higher filtration efficiency. As in the accumulation of dust on the surface of the filter material, filter efficiency and resistance are corresponding increase, when the pressure difference on both sides of the filter material is very big, can put some tiny dust particles are attached to the filter material has been squeezed in the past, the dust collector efficiency decline. In addition, the high resistance of the dust collector can significantly reduce the air volume of dust removal system. Therefore, the dust collector's resistance reaches a certain number, and the dust should be cleared in time. Do not destroy the initial layer when clearing ash, so as not to decrease the efficiency.
Product Details: Product Type Other Technology Other Power Source Electricity Operating Type Automatic Power 420 Volt (v) Pressure 6-7 Bar Surface Treatment Painted Supply Ability : 7-10 Unit Per Month Price And Quantity: Minimum Order Quantity 1 Unit Price Range 2500000.00 - 3000000.00 INR/Number Product Specifications: Warranty: All our machines are warranted for 12 months from the date of commissioning or 15 months from the date of dispatch whichever is earlier against all manufacturing defects. However this warranty not covers parts consumed at normal wear and tear during operation like rubber goods & parts in continuous contact of abrasive media and also any damages due to misuse or improper handling of the machine at customer premises. The warranty will lapse if customer uses spurious spare parts purchased from any other buyer on the machine and fail to operate and maintain the machine in accordance with the instructions. Product Type Other Power Source Electricity Power 420 Volt (v) Usage/Applications Casting, Forging, Sheet metal etc Color Dark Blue Technology Other Operating Type Automatic Surface Treatment Painted Pressure 6-7 Bar Product Description: The Tunnel type/ roller conveyor shot blasting machine is best suitable for the shot blasting of I/H-Beam /Structural Steel Components etc. It consists of inlet and outlet side Roller conveyors as material handling systems. The components to be blasted are placed on inlet side of the roller conveyor, from where it travels forward and enters into the inlet tunnel. After passing through the inlet tunnel components enters into the blast zone which consists of 4 nos. of Blast Wheels. All these Blast wheel units are strategically placed around the Blast cabinet. The arrangement of the blast wheel ensures optimum blast cleaning and maximum utilization of the abrasive energy. Blast wheels fires the abrasive at high velocity onthe forward moving components & blast cleans them thoroughly. Blasted material moves forward and enters into the outlet tunnel. The spent abrasive from blasting operation after passing through the perforated floor plates will get collected in to the cabinet's bottom storage hopper. From where it is transferred to the bucket elevator, which elevate the abrasive vertically and discharges the same into a media separation unit where dust and fine abrasives are cleaned ensuring that only clean abrasive will re-circulate to the blast wheel units for effective and better cleaning. A Dust collection system is provided with the machine which will continuously remove the dust and fine particles, thus keeping the inside of the machine and the nearby environment dust & pollution free.
