We can supply solar transformers ideally suited for large MW scale solar PV plants. Bullet Points - . Inverter duty Solar transformers, suitable for solar load profile . Multi-winding (2 to 6 windings), oil-filled or dry type. . 2MVA to 12.5MVA, LV Side: 0.35kV to 0.69kV, HV Side 3.3kV to 33kV . Low-loss, with Aluminum or Copper winding. . Electrostatic shield between LV and MV Winding. For more details please contact us.
Inverter Battery Features Long Life Life-1200 Cycle Special Tubular positive spines cast at high pressure 100 bar to raise corrosion life Extra Back-up Excellent reserve capacity for long backup. More current density, max. AH efficiency. Operating Specific Gravity 1.250 +/-0.005 at 270C. Deep Cycle Back-up high charge acceptance due to usage of quality PE separator. Special additives for better charge acceptance & retention. Low Maintenance Special Alloy grids ensures low gassing and minimum water loss. 20% Extra electrolyte for less topping & batter thermal Management Low internal resistance seal proof leak proof. Float indicators level.
2 Volt LMLA Battery Cell Features Positive Plate-Tubular low corrosion grid & Low self-discharge rates. Negative Plate- lead grid providing low corrosion & low enhanced force life because of very less discharge Terminals �¯�¿�½?�?�¯�¯�¿�½?�?�¿�¯�¿�½?�?�½?�?�¯ï¿½?�¿ï¿½?�½?�¯�¿�½?�?�¢?? Antimonial lead, specially designed for sustained high current Container & lid-high grid polymer Separator-Envelope type high density and porosit Connectors-lead plated copper connectors. Advantage Easier to Install Low water top-up during service life. Long life because of very low corrosion & enhance free self discharge rate. Proven cycling & deep cycling capability Enhancement in life High buy back value after the end of the life. Eco Friendly Low emission of corrosive fumes or gases under normal operating conditions.
TRANSFORMER : ALL TYPE : Dry Type/Air Cooled, Oil Cooled, Water. We can supply small transformer from 33kV and up to 54000kVA or more. For more details please contact us.
Power Modules are Point of Load (POL) DC-DC converters integrating controller chips, chokes and I/O capacitors into a single power management package for step-down(buck) applications. The low profile and compact size enables significant saving of board space, high efficiency enhances application performance, and design structure allows automated assembly by standard surface mount equipment
40Kw Off Grid Inverter With CSA/UL Approved Our SDP series Off Grid Pure sine wave inverter is one of the most advanced DC to AC conversion products in the world, it is suitable use for areas without electricity, vehicles, ships, solar energy, wind turbine and other renewable energy systems and etc, can supply power and provide guarantee effectively for the areas with traffic inconveniences, in the mountains, pastoral, border, island and other areas without electricity. It has the main advantages of high quality sine wave AC output, microcomputer control, humanness design, and it is high efficiency and low no-load loss, and no pollution. The inverter can also supply AC power to all kinds of electric equipment, air conditioners, motors, refrigerators, lights, TV, electric fans and other industrial power supply. 1. Using the sixth generation efficient IPM intelligent module from Japanese Mitsubishi, high efficiency and stable performance. It with powerful protection function, the protection for short circuit, over load, over temperature is more safe and reliable. Itâ??s service life can up to 15 years or more. 2. Intelligentized, modularized, simple structure design with powerful function. 3. Two kinds of start mode: Step-down Voltage Start and Variable Frequency Start. Customers can set start mode according to the type of their load. This function is very convenient for users and also reduce frequency converterâ??s usage, which reduced the cost of equipment investment, easy to connect wires and control. 4. The output frequency can be setting via LCD panel, itâ??s very convenient for customer. 5. The output voltage can be set between -40 % to +20 % of rated voltage. And the output voltage is very accuracy �±1%. 6. The DC input voltage range can be set. Over-voltage point, under-voltage point, over-voltage recovery point, under-voltage recovery point all can be setting via the LCD panel. 7. Pure sine wave output. With good dynamic response less than 50MS, waveform distortion rate smaller, higher conversion efficiency and stable output voltage. 8. Low Frequency Transformer, which ensures that inverter has high efficiency. 9. High conversion efficiency, Max. Efficiency 94%,if 48VDC input, the efficiency can more than 85%. 10. Adopts black pure aluminum radiator, which confirms the best radiating performance. 11. Powerful data display function. LCD can display the DC input voltage, output frequency, phase voltage, phase current, AC bypass input voltage, output power KWH, time and date, temperature, fault code display. 12. Wide input voltage can be set according to customer's requirement. Input voltage range can be selected from 150-400V or 300-600V or 400-800V. 13. Wide input voltage can work without battery and solar charge controller, save more cost and With MPPT wide voltage input function, maximum use of solar power.
Product Introduction SANDI AC/DC Charger is specially developed for DC chargers module. It has high efficiency, high power factor, high power density, high reliability advantage. AC input 3 phase or single phase, DC output voltage range from 100 to 750VDC can be set, compliant with CE safety requirements, EMC standard EN61000-6-3 and EN61000-6-1 Class A, it is an advanced international level charger module. Unique function High efficiency over the full load range, full load efficiency greater than 95.5% Wide output voltage range, 100-750VDC, suitable for a wide range of Lithium and lead acid battery 5-inch LCD touch screen, easy to operate Flexible application, charging voltage, charging current, charging time, timing charging can be set by LCD screen, easy to operate Main features Powerful protection, overheating, short circuit, overload, overvoltage, undervoltage, etc. Three phase active power factor correction technology, reduces the harmonic interference to the grid Dual DSP design, achieve the full digital control, less components means high reliability Wide input voltage range, allows operation in most poor grid conditions Soft start charging and soft shutdown minimize the impact on the battery. Input, output have protective circuit breaker switch Module adopts hot pluggable design, which is convenient for maintenance. CAN/RS485 interface (Optional)
Product advantages: ï?¬All-in-one design, high integration and space saving installationï¼? ï?¬Using high-performance lithium iron phosphate cells, laser welding, good cell consistency, designed service life of more than 10 yearsï¼? ï?¬Master-slave mode, passive equalization, can manage the equalization resistance, can set the equalization start voltage difference, and monitor the equalization resistance temperature, more intelligent and safe, and reduce the impact of barrel effect on system energy storage BMS adopts NXP(USA) automotive-grade high-performance chips, with strong anti-interference, good reliability and wide temperature range CAN2.0 communication interface, has the advantages of strong real-time performance, long transmission distance, strong anti-electromagnetic interference ability System parameters can be set through the host computer, such as fan start/stop temperature, charger maximum current setting, charge and discharge current correction, SOC correction, with insulation leakage detection function to prevent oil leakage and short circuit of the cell Integrate Solar charge controller or AC charger optional, BMS communication control, more safe and reliable; Cell temperature management, can be automatically controlled with the air conditioner heater according to the cell condition to make the cell works at the most suitable temperature, and can be linked with the fire protection system as needed Performance characteristics Built-in BMS management system with comprehensive protection and monitoring control functions 5" LCD screen display, easy to operate, can check the temperature, voltage, working status, discharge current, dynamic and static SOC algorithm of a single cell, local display of alarm info, alarm level distinction, accurate positioning of abnormal cells Main control MCU can be centrally controlled and manage peripheral settings (AC charging module, inverter module, solar charging module) to adjust the charging current and voltage of peripheral devices according to the battery charging curve, making the system more reliable BMS battery management system, with SOC automatic calibration and high current passive balance function, combined with perfect operation control and management strategy, to achieve accurate and efficient management EMS energy management system, BMS with solar controller/AC charger, inverter centrally manages charge and discharge, effectively controls the charge and discharge current within the cell usage conditions, protects the cell and extend its service life