Introduction to Instrument PQWT-CL300 series underground pipes water leak detector, is high performance leak detection equipment, has powerful anti-jamming and data processing capabilities, you can make your work easier. It has the following main features. Main Features 1.The use of latest digital signal processing chip and a digital filter chip, 16M cache controller integrated, more responsive. In particular, it can filter with the interference of environmental noise, screening out the leakage noise, allowing the operator to lock leakage points quickly. 2. 7-inch high-definition digital color LCD touch screen with a resolution of 800 * 480, can provide 8 display pages, can show the measurement parameters more clearly and intuitively, and full touch screen design, simple operation. 3. 50 ~ 2500Hz frequency range (spectrum analysis), real-time display of the noise signal distributed on each frequency. 4.Sensor is built-in preamp circuit, using a rubber ring seal and cushion, and the application of professional acoustic methods, making the ability to capture the noise is higher than similar products. 5,Adopt latest noise detecting element, sounds clear. 6.Save 8 sections totaling eight minutes of recording, which is not lost after shut down, could be analyzed at any time. 7.Using a large capacity battery, can work for more than ten hours , and can be removed charging and online charging. 8. Super anti-jamming circuit design, digital signal and analog signal effectively isolate and eliminate the noise generated by the digital circuit . Model No. :PQWT-CL300 Measuring Depth :2 meter Frequency Range: 50-2500HZ Audio Amplifier Gain: Adjustable within the class of 100 Operation Mode :Spectral Analysis,Filter Analysis ,Fine Mode LCD :7-inch Touch Screen Power Supply : 12V 3600mAh Rechargeable Battery
Description of PPR Pipe Extrusion Line: Diameter Scope: 20mm-160mm PPR pipe introduction: We designs and develops PPR pipe production line and gas pipe production line by itself. Plastic Pipes that are produced by this line have excellent stiffness, energy-saving insulation and non-toxic, health performance so on. It has become the first choice for the hot/cold water pipe. Technical Introduction Firstly, put PP-R material and other assistant material into the mixer and mixing the material symmetrically, then feed into the hopper, at the same time heat extruder and keep the temperature, and the material is melt and plasticizing by extruder, then extruded by die and head and goes into vacuum calibrating device, and cooling and calibrating, then draw-off by haul-off machine, then printing word by ink jet printer, then put into automatic cuter to finish the automatic cut according to pre-establishing length and stacking into the shelf. And the eligible product is packed and put into storeroom, and inferior product is crushed and recycled. This pipe extrusion line mainly includes single screw extruder, molds, vacuum calibrating water tank, spray water cooling tank, haul-off machine, cutting machine (or winder) and overturning bracket.
The PE water supply pipe is extruded by the extruding product lines with special purpose polyethylene material. The pipes apply to cities and towns water supply pipeline net, irrigation and channel water project, garbage treatment site, sewage collecting pipeline project and agriculture spray irrigation project. Because the PE pipeline adopts the thermal fusion and electric fusion connection technologies, the interface has been integrated and the pipeline can resist the hoop stress and axial shock resistant stress produced by inside pressure. In addition, the PE pipe does not contain the heavy metalsalt stabilizer. The second pollution for drinking water is avoided for the pipe material no toxic, no pipe scale and not breeding bacteria. Product Specificationú¦Nominal (outside diameter): 25-630mm series Pressure Grades: SDR11
Pexb-anuv tubing Runzhou PEX-b anUV potable pipe is a silane cross-linked plyethylene pipe for hot and cold water system. It can be used for 20 years outdoor and 50 years indoor. Feature:Two layers structure: The internal layer is made up of silane cross-linked polyethylene. The external layer is mixed with polyethylene and carbon black,which has anti-ultraviolet ray. Observed Standard : GB/T 17219-1998 and GB/T 18992.2-2003. 16*2.4mm, weight:98g/m
Runzhou pex-b anuv potable pipe is a silane cross-linked plyethylene pipe for hot and cold water system. It can be used for 20 years outdoor and 50 years indoor. Feature:two layers structure: the internal layer is made up of silane cross-linked polyethylene. The external layer is mixed with polyethylene and carbon black, which has anti-ultraviolet ray. Observed standard : gb/t 17219-1998 and gb/t 18992.2-2003. Dn16~dn63
Nominal diameter:20-800mm Rate:0.6-1.6mpa No package
Lilac recycled water pipe Lilac recycled water pipe for australian local application, polyethylene material
HDPE water pipe is made from high-density polyethylene resin, which belongs to flexible plastic pipes. HDPE water pipes have good rigidity and toughness, excellent corrosion resistance and high impermeability and strong molecular bond help them to have the high mechanical strength to bear high pressure. HDPE water pipes are usually used for fluid transmissions, such as water, rural irrigation, seawater and drainage, etc. HDPE (High-Density Polyethylene) water pipes are commonly used in water supply systems due to their high durability, corrosion resistance, and flexibility. HDPE pipes have several advantages over traditional piping materials like metal, concrete, or PVC, including their ability to withstand high pressure, temperature, and impact. One of the main benefits of HDPE water pipes is their ability to resist corrosion and chemical reactions, making them an ideal choice for water supply systems. Additionally, HDPE pipes are lightweight, making them easy to transport and install. They are also flexible, which allows them to withstand ground movements and settle with soil movement without breaking or leaking. In terms of installation, HDPE pipes can be joined together using various methods such as butt fusion, electrofusion, or mechanical fittings, which are easy to use and require minimal expertise. The jointing methods create a seamless, leak-proof connection between the pipes, ensuring long-term reliability and reduced maintenance costs.
The Quick Details of Pe100 Water Pipe : Place of Origin: Luoyang ,China Material: HDPE Brand name: GUORUNXINCAI Material: HDPE Diameter Nominal: 20-800mm Wall Thickness: 2.3-57.2mm Pressure: 0.6-1.6Mpa Standard: GB/T 13663-2000 Pe100 Water Pipes' diameter,length and other types of indexes can be based on clients' requirement. IRRIGATION PIPE of High Density Polyethylene High-density polyethylene pipe(HDPE pipe) is made from high density polyethylene as the main raw material, adding a small amount of antioxidants, Anti-UV absorbers and pigments. Pe100 Water Pipes' main characteristics: 1. Long-life-span Pe100 Water Pipes can be used for more than 50 years under normal condition 2. Good sanitary performance Pe100 Water Pipes' material is non-toxic, does not scale. It is not easy to form dirt, and avoids secondary pollution of drinking water 3. Good corrosion resistance Pe100 Water Pipes can resist variety of chemical mediator except few oxidants 4. Pe100 Water Pipes are with Good crack growth resistance 5.Pe100 Water Pipes are with Little coefficient of friction and low flow resistance 6.Pe100 Water Pipes are with Excellent wear resistance Its wear resistance is 4 times higher than steel pipe under normal conditions 7. Good solderability Pe100 Water Pipes' interface strength is higher than the pipe body 8. Pe100 Water Pipes are with Fine flexibility and anti-scratch ability 9. Low cost Pe100 Water Pipes can reduce the cost of project substantially The Applications of Pe100 Water Pipes: Guorun Pe100 Water Pipes can be widely applied to below fields: 1. City and town water supply 2. To transport natural gas & coal gas 3. Food & chemical industry 4. To transport ore & mud 5. To replace cement pipe, cast iron pipe & steel pipe 6. Landscaping pipeline Pe100 Water Pipes outer diameter is from 20 mm to 800 mm, and its wall thickness is 2.3 mm to 57.2 mm mainly.
Description of PVC Water Pipe Extrusion Line: Qingdao HUASU Machinery Fabricate Co., Ltd designs and develops PVC pipe extrusion line especially for PVC water supply and disposal pipe. PVC water pipe extrusion line is specializing in manufacturing PVC,CPVC and UPVC pipes of different diameter and thickness. They are applied to agricultural and construction water supply and drainage, overhead or underground wire and cable. Due to the special characteristics of the CPVC plastic pipes, they are widely used in the fields of crude oil transportation, pipe lines of chemical industry which require high temperature and corrosion resistance, hot and lukewarm water supply and drainage system, directly buried pipes of high and extra high voltage electricity, protection sleeves of wires and cables, etc. High quality steel materials, strict producing process makes high quality line. This PVC pipe extrusion line mainly consists of conical twin screw extruder, PVC pipe molds, vacuum calibrating water tank, water spraying cooling tank, haul-off machine, cutting machine and overturning bracket.
