Working temperature from -40oC up +120oC: Dimensions;full sizes Length: 20m/pcs, 50m/pcs
Hydraulic rubber hose sae100r1at 1/4", 5/16", 3/8", 1/2", 5/8", 3/4", 1", 1 1/4", 1 1/2", 2"
Hydraulic rubber hoses are used in high-pressure hydraulic systems for control and power supply. They are designed for the main transmission of hydraulic fluids (hydraulic fluids according to ISO 6743-4, except HFD R, HFD S and HFD T fire resistant fluids). For other applications (e.g. compressed gases), always contact Sanshi Rubber's technical department. For water, water-based liquids and air, the maximum working temperature is +70�°C. For air over 17 bar, the hose cover should have pinholes and be additionally protected. Hydraulic rubber hoses are manufactured in imperial sizes with standardized inner diameters. The most popular standards for setting hose requirements are: European standard - EN, International ISO and American SAE. symbols of the standards and the most important data (diameter, working pressure and date of manufacture) are marked on the hose. In addition, the hose may bear a specific name assigned by the manufacturer or the customer. Characteristics of hydraulic rubber hoses Greater flexibility Minimum bend radius is smaller than standard hydraulic hose. Higher pressure parameters Hydraulic hoses with a maximum working pressure higher than standard requirements. This expands the application range of the hose while maintaining a safety factor and the same hose diameter, so there is no need to change it (e.g., make it smaller) or change its type (e.g., from a double braided hose to a spiral hose). Higher temperature parameters Hydraulic hoses have specific operating temperature ranges. For hoses with textile braid (2TE, 3TE types), with compact steel wire braid (1SC, 2SC, 1SN, 2SN) the range is -40C to +100C (peak up to 125C ), and suitable for a certain set of hoses with spiral braid (4SP, 4SH). For spiral hydraulic hoses with constant operating pressure, regardless of diameter (R12, R13, R15), the range is -40C to +121C (peak up to 125C). Sometimes hydraulic systems may operate at temperatures higher than standard hydraulic hoses. If the recommended temperature is exceeded, the rubber begins to lose its elasticity and hardens, and then begins to leak at the end of the hose near the fitting. In this case, a hose with a higher operating temperature range should be used.
Hydraulic Rubber Hose Hydraulic rubber hoses are used in high-pressure hydraulic systems for control and power supply. They are designed for the main transmission of hydraulic fluids (hydraulic fluids according to ISO 6743-4, except HFD R, HFD S and HFD T fire resistant fluids). For other applications (e.g. compressed gases), always contact Sanshi Rubber's technical department. For water, water-based liquids and air, the maximum working temperature is +70�°C. For air over 17 bar, the hose cover should have pinholes and be additionally protected. Hydraulic rubber hoses are manufactured in imperial sizes with standardized inner diameters. The most popular standards for setting hose requirements are: European standard - EN, International ISO and American SAE. symbols of the standards and the most important data (diameter, working pressure and date of manufacture) are marked on the hose. In addition, the hose may bear a specific name assigned by the manufacturer or the customer. Characteristics of hydraulic rubber hoses Greater flexibility Minimum bend radius is smaller than standard hydraulic hose.
Place of Origin: Hebei, China (Mainland) Brand Name: GARSON Model Number: SAE 100R15 Material: Synthetic Rubber Color: Black,other colors can be customized Application: transportation of petroleum or water. Name: High Pressure Oil Hose Reinforcement: High Tensile Steel Wire Certification: ISO9001 Size: 10-38mm(3/8-1 1/2inch) Cover: Weather Resistant Synthetic Rubber Type: hydraulic rubber hose
Hydraulic hose 1.The high temperature rubber hose composed of inner rubber layer, multi-layer fabric layer and outer rubber layer. 2.Advantages: The rubber tube has the advantages of small outer diameter tolerance, good oil resistance and heat resistance, light weight, soft, long durability and so on. 3.Professional rubber hose supplier 4.The color, sizes, thickness, pressure and length all can be customized.
Construction: Inner Tube:NBR, Black, Smooth. Reinforcement:Fine wire reinforced, Electrically conductive. Cover:Synthetic Rubber. Temperature:-20 C to +45 C. Feature:Conveying medium: Industrial water, waste water, seawater and irrigation inagriculture. Character: The hose has dual performance that is able to bear positive & negative pressure, it is able to work freely under the vacuum-80kpa(600mm mercury column), without flat& delamination, has good flexural property. The rubber body is flexible, the burst pressure is at least treble than working pressure.
EN854-2TE Hydraulic Hose with Oil and Weather Resistant Cover CONSTRUCTION: This hose shall consist of an oil and water resistant synthetic rubber lining,two of suitable textile yarn and an oil and weather resistant synthetic rubber cover. APPLICATION: Hydraulic fluids in accordance with ISO6743-4 with the exception of HRD R, HFD S, and HFD T at temperature range of -40~+70 EN854-2TE hydraulic hose: is similar to EN854-1TE hydraulic hose in application. It is also used to handle hydraulic fluids in accordance with ISO6743-4 with the exception of HRDR, HFDS and HFDT. And the temperature of hydraulic fluids ranges from -40C to +100C. It is composed of three parts: tube, reinforcement and cover. Tube is made from oil and water resistant synthetic rubber, making hose perform well in delivering hydraulic oil. Reinforcement is made from one layer of high tensile textile fiber braid, making hose bear high working pressure. Cover is made from oil and weather resistant synthetic rubber, making hose suitable for harsh working environment and have long service life. EN854-2TE hydraulic hose can bear high working pressure because of its high tensile textile fiber braid reinforcement. EN854-2TE hydraulic hose is suitable for harsh working environment for its oil and weather resistant synthetic rubber cover. The details of EN854-2TE hydraulic hose: Structure: it is composed of three parts: tube, reinforcement and cover. Tube: oil and water resistant synthetic rubber. Reinforcement: one layer of high tensile textile fiber braid. Cover: oil and weather resistant synthetic rubber. Temperature range: -40C to +100C. Hose ID: 4.76 mm - 25.4 mm.
EN854-2TE Hydraulic Hose with Oil and Weather Resistant Cover CONSTRUCTION: This hose shall consist of an oil and water resistant synthetic rubber lining,two of suitable textile yarn and an oil and weather resistant synthetic rubber cover. APPLICATION: Hydraulic fluids in accordance with ISO6743-4 with the exception of HRD R, HFD S, and HFD T at temperature range of -40~+70 EN854-2TE hydraulic hose: is similar to EN854-1TE hydraulic hose in application. It is also used to handle hydraulic fluids in accordance with ISO6743-4 with the exception of HRDR, HFDS and HFDT. And the temperature of hydraulic fluids ranges from -40 C to +100 C. It is composed of three parts: tube, reinforcement and cover. Tube is made from oil and water resistant synthetic rubber, making hose perform well in delivering hydraulic oil. Reinforcement is made from one layer of high tensile textile fiber braid, making hose bear high working pressure. Cover is made from oil and weather resistant synthetic rubber, making hose suitable for harsh working environment and have long service life. EN854-2TE hydraulic hose can bear high working pressure because of its high tensile textile fiber braid reinforcement. EN854-2TE hydraulic hose is suitable for harsh working environment for its oil and weather resistant synthetic rubber cover. The details of EN854-2TE hydraulic hose: Structure: it is composed of three parts: tube, reinforcement and cover. Tube: oil and water resistant synthetic rubber. Reinforcement: one layer of high tensile textile fiber braid. Cover: oil and weather resistant synthetic rubber. Temperature range: -40 C to +100 C. Hose ID: 4.76 mm - 25.4 mm.
Hengshui Bettis Rubber and Plastic Co.,Ltd as one of the leading and professional hydraulic hose manufacturer in China, we has more than 20 years history, with more than 16000 square meters workshop, nearly 200 sets of main processing machineries and 20 sets of inspection and test machines. We have nearly 300 skilled and well-trained staffs, and more than 50 experienced technicians and qualified administrants. We mainly produce wire braid and wire spiral hydraulic hoses, such as SAE 100 R1AT hose, SAE 100 R2AT hose, SAE 100 R9AT hose, SAE 100 R12 hose, SAE 100 R13 hose, DIN 20022 / EN 853 1SN hose, DIN 20022 / EN 853 2SN hose, DIN 20023 / EN 856 4SP hose, DIN 20023 / EN 856 4SH hose, and SAE 100 R1A hose, SAE 100 R2A hose, DIN 20022 1ST / EN 853 1ST hose, DIN 20022 2ST / EN 853 2ST hose and other hoses. Our output per year is more than 5,000,000 meters and quickly growing year after year.
