Continent Technology Limited

SANDI SERIES charging module is for electric vehicle charging station. With single-phase non neutral conductor AC input, it has the advantages of high efficiency, high power density and low harmonic. Functional details 1. Hot plug Plug technology is applied to the charging module to provide convenience for installation and maintenance. The access of the charging module to the system shall not disturb the output voltage of the system. 2. Advanced current sharing technology Under constant voltage working mode, the charging modules can share current automatically within 10S, with degree of unbalance less than �±0.5A. 3. Control of input limited power Refer to Fig. 1-10 for the relation between the output power and input voltage of the charging module. When the input voltage is within 360 Vac ~ 450 Vac (return difference is less than 5V), the module can output the maximum power of 20 KW; when the input voltage is within 260 Vac ~ 320 Vac, the module can still work normally under limited power mode. 4. Control of output constant power When there is a rated input voltage, the output power of the module is 20 KW. Refer to Fig. 11 for the relation between the output voltage and the output current of the module. The SD75050 module uses two operating modes with output voltage ranges of 50 to 750V. The module only selects the operating mode based on the value of the received demand voltage, and does not select the operating mode based on the actual output voltage. 5. Temperature limited power 6. Regulation of output current limiting point 8. Regulation of output voltage The output voltage of the module can be regulated constantly through the external monitoring module, with regulation range of 50Vdc ~ 750Vdc and minimum regulation step of 0.1 Vdc. 9. Fan control The built-in processor of the module can regulate the speed of the fan according to the internal temperature and output current of the module. 10. Protection of input overvoltage/ voltage shortage 11. Output overvoltage protection The overvoltage protection point is 260Vdc ~770Vdc (�±10 Vdc). Default is 778Vdc.The module can be started after manual intervention upon overvoltage protection. 12. Over-temperature protection The environmental over-temperature protection point is 80�°C. When the DC panel has a temperature over 100�°C, the module will stop working; when the DC panel has a temperature below 90�°C, the module will automatically work again. 13. Protection of internal bus fault When the internal bus voltage of the module is beyond the overvoltage/ voltage shortage protection point, the module will be powered off automatically. At this time, there is no output from the module and the fault indicator light is on. 14. Short circuit protection In case of short circuit of the module, it will be subjected to protective shutdown and the red indicator light of the panel is on, and this condition will be transmitted to the monitor of the "module fault".

Lithium battery materials--lithium iron phosphate--lifepo4 lithium ion ev battery cathode materials In 2013, our bolivia project for batery production line has completed successfully. Bolivia president and goverment gave a full support and confirm. And our next project for indonisia will start this year. cmb) And other cathode&anode battery materials;alumimun foil, copper foils, battery separator, etc. 2.)full set of lithium battery equipments, for example: Mixing machine --coating machine--oven--rolling machine--welding machine--slitting / cutiing machine --winding machine--sealed machine, etc. 3)full set of lithium battery technology. We can design the laboratory and production line, according to customer's request. We are the first and earliest exporter for li-ion battery materials.Our original alibaba company name is linyi gelon new battery materials co., ltd.Which has 8years exporting experience and 5 years gold supplier memberships in alibaba. For more details, please feel free to contact us by: Katie at libgroup.Ent Skype: katiegelon Standard package

Product description 1. Model: ni-mh battery 14.4v d9000mah rechargeable battery pack(12s of fh-d9000). 2. Un, rohs, ce approved ni-mh battery pack. 3. Ni-mh battery pack oem orders are welcomed. 4. Ni-mh battery pack is widely used to consumer portable equipments, information devices, miner lamps, power tools, remote control toys, medical devices, vacuum cleaner, cordless phone, etc. 5. Bulk pack, blister card are available. 6. For ni-mh standard industrial series d size, other capacity are availabe from 2500mah to 10000mah. 7. Customizes shapes, capacity, and voltage are accepted. 8. Individual cells can be assembled in parallel or series into stacks as required by customers. 9. No memory effect, high voltage, high energy density, long cycle life. 10. Eco-friendly. Ni-mh 12v d9000mah rechargeable battery pack(10s of fh-d9000) CellNi-mh Model12s of fh-d9000 Nominal voltage14.4v Nominal capacity9000mah Minimal capacity8800mah Standard charge900 ma, 16 hrs Rapid charge: 4500 ma, 2.2 hrs (control required) Continuous discharge Less than 9000 ma Final discharge voltage1.0 v (less than 1.0c) Service life =500 cycles (iec61951-2-2003) Dimension(w*l*h) 65mm*198mm*65 Weight Approx. 1960 g Ambient temperature:Standard charge: 0~45 ºc Rapid charge: 10~40 ºc Discharge: -20~50 ºc Store (65+20% rh)Less than 360 day: -20~30 ºc Less than 30 day: -20~40 ºc Notes: 1."c" behind the model no. Refers to normal consumer series ; 2. Capacity obtained after charge at 0.1c for 16 hrs and discharge at 0.2c to 1.0v at 25 ºc; 3. Control required: 1) -?v: 0 ~ 5mv 2) d t / d t: 0.8 ºc/ min 3) t co: 40 ~ 45 ºc

Product description 1. Model: ni-mh battery 6.0v d3800mah rechargeable battery pack(6s of fh-d3800). 2. Un, rohs, ce approved ni-mh battery pack. 3. Ni-mh battery pack oem orders are welcomed. 4. Ni-mh battery pack is widely used to consumer portable equipments, information devices, miner lamps, power tools, remote control toys, medical devices, vacuum cleaner, cordless phone, etc. 5. Bulk pack, blister card are available. 6. For ni-mh standard industrial series d size, other capacity are availabe from 2500mah to 10000mah. 7. Customizes shapes, capacity, and voltage are accepted. 8. Individual cells can be assembled in parallel or series into stacks as required by customers. 9. No memory effect, high voltage, high energy density, long cycle life. 10. Eco-friendly. Ni-mh 6v d3800mah rechargeable battery pack(5s of fh-d3800) CellNi-mh Model5s of fh-d3800 Nominal voltage6.0v Nominal capacity3800mah Minimal capacity3700mah Standard charge380 ma, 16 hrs Rapid charge: 1900 ma, 2.2 hrs (control required) Continuous discharge Less than 3800 ma Final discharge voltage1.0 v (less than 1.0c) Service life =500 cycles (iec61951-2-2003) Dimension(w*l*h) 33mm*165mm*65 Weight Approx. 400 g Ambient temperature:Standard charge: 0~45 ºc Rapid charge: 10~40 ºc Discharge: -20~50 ºc Store (65+20% rh)Less than 360 day: -20~30 ºc Less than 30 day: -20~40 ºc Notes: 1."c" behind the model no. Refers to normal consumer series ; 2. Capacity obtained after charge at 0.1c for 16 hrs and discharge at 0.2c to 1.0v at 25 ºc; 3. Control required: 1) -?v: 0 ~ 5mv 2) d t / d t: 0.8 ºc/ min 3) t co: 40 ~ 45 ºc

Hi, My name is Darcy Huang and I am the Sales Manager of PLB. PLB is a high-tech enterprise and specializes in R&D, manufacturing 26650 lithium ion battery in Dongguan China. Our factory has been working since Feb 10th, If interested to acquire please let me know, I would love to provide more information on this. Thank you. Darcy@plb.com.cn

Input : 110V/220V, 47-63HZ Specification: DC24V 4Amp Constant Charging Voltage : 29.4V (7s li-ion battery) Constant Charging Current:4A Charging Mode : 3 Stages, CC, CV, Trickle Material: Aluminum alloy with Fan Dimension : 135*90*50mm Net Weight :0.7kg Application : Electric Vehicles & Tools Various Protection: Over-current, Over Voltage, Over Temperature, Short Circuit, and Reverse Polarity. Products can be Customized!

Consumer electronic battery, Energy storage Handheld device battery Medical device battery Smart home battery Security battery Outdoor lighting battery etc

Product description 1. Model: ni-mh 12v d10000mah rechargeable battery pack(10s of fh-d10000). 2. Un, rohs, ce approved ni-mh battery pack. 3. Ni-mh battery pack oem orders are welcomed. 4. Ni-mh battery pack is widely used to consumer portable equipments, information devices, miner lamps, power tools, remote control toys, medical devices, vacuum cleaner, cordless phone, etc. 5. Bulk pack, blister card are available. 6. For ni-mh standard industrial series d size, other capacity are availabe from 2500mah to 10000mah. 7. Customizes shapes, capacity, and voltage are accepted. 8. Individual cells can be assembled in parallel or series into stacks as required by customers. 9. No memory effect, high voltage, high energy density, long cycle life. 10. Eco-friendly. Ni-mh 12v d10000mah rechargeable battery pack(10s of fh-d10000) CellNi-mh Model10s of fh-d10000 Nominal voltage12v Nominal capacity10000mah Minimal capacity9800mah Standard charge1000 ma, 16 hrs Rapid charge: 5000 ma, 2.2 hrs (control required) Continuous discharge Less than 15000 ma Final discharge voltage1.0 v (less than 1.0c) Service life =500 cycles (iec61951-2-2003) Dimension(w*l*h) 65mm*165mm*65 Weight Approx. 1800 g Ambient temperature:Standard charge: 0~45 ºc Rapid charge: 10~40 ºc Discharge: -20~50 ºc Store (65+20% rh)Less than 360 day: -20~30 ºc Less than 30 day: -20~40 ºc Notes: 1."c" behind the model no. Refers to normal consumer series ; 2. Capacity obtained after charge at 0.1c for 16 hrs and discharge at 0.2c to 1.0v at 25 ºc; 3. Control required: 1) -?v: 0 ~ 5mv 2) d t / d t: 0.8 ºc/ min 3) t co: 40 ~ 45 ºc