Working temperature from -40oC up +120oC: Dimensions;full sizes Length: 20m/pcs, 50m/pcs
Hydraulic rubber hose sae100r1at 1/4", 5/16", 3/8", 1/2", 5/8", 3/4", 1", 1 1/4", 1 1/2", 2"
Hydraulic rubber hoses are used in high-pressure hydraulic systems for control and power supply. They are designed for the main transmission of hydraulic fluids (hydraulic fluids according to ISO 6743-4, except HFD R, HFD S and HFD T fire resistant fluids). For other applications (e.g. compressed gases), always contact Sanshi Rubber's technical department. For water, water-based liquids and air, the maximum working temperature is +70�°C. For air over 17 bar, the hose cover should have pinholes and be additionally protected. Hydraulic rubber hoses are manufactured in imperial sizes with standardized inner diameters. The most popular standards for setting hose requirements are: European standard - EN, International ISO and American SAE. symbols of the standards and the most important data (diameter, working pressure and date of manufacture) are marked on the hose. In addition, the hose may bear a specific name assigned by the manufacturer or the customer. Characteristics of hydraulic rubber hoses Greater flexibility Minimum bend radius is smaller than standard hydraulic hose. Higher pressure parameters Hydraulic hoses with a maximum working pressure higher than standard requirements. This expands the application range of the hose while maintaining a safety factor and the same hose diameter, so there is no need to change it (e.g., make it smaller) or change its type (e.g., from a double braided hose to a spiral hose). Higher temperature parameters Hydraulic hoses have specific operating temperature ranges. For hoses with textile braid (2TE, 3TE types), with compact steel wire braid (1SC, 2SC, 1SN, 2SN) the range is -40C to +100C (peak up to 125C ), and suitable for a certain set of hoses with spiral braid (4SP, 4SH). For spiral hydraulic hoses with constant operating pressure, regardless of diameter (R12, R13, R15), the range is -40C to +121C (peak up to 125C). Sometimes hydraulic systems may operate at temperatures higher than standard hydraulic hoses. If the recommended temperature is exceeded, the rubber begins to lose its elasticity and hardens, and then begins to leak at the end of the hose near the fitting. In this case, a hose with a higher operating temperature range should be used.
Hydraulic Rubber Hose Hydraulic rubber hoses are used in high-pressure hydraulic systems for control and power supply. They are designed for the main transmission of hydraulic fluids (hydraulic fluids according to ISO 6743-4, except HFD R, HFD S and HFD T fire resistant fluids). For other applications (e.g. compressed gases), always contact Sanshi Rubber's technical department. For water, water-based liquids and air, the maximum working temperature is +70�°C. For air over 17 bar, the hose cover should have pinholes and be additionally protected. Hydraulic rubber hoses are manufactured in imperial sizes with standardized inner diameters. The most popular standards for setting hose requirements are: European standard - EN, International ISO and American SAE. symbols of the standards and the most important data (diameter, working pressure and date of manufacture) are marked on the hose. In addition, the hose may bear a specific name assigned by the manufacturer or the customer. Characteristics of hydraulic rubber hoses Greater flexibility Minimum bend radius is smaller than standard hydraulic hose.
Place of Origin: Hebei, China (Mainland) Brand Name: GARSON Model Number: SAE 100R15 Material: Synthetic Rubber Color: Black,other colors can be customized Application: transportation of petroleum or water. Name: High Pressure Oil Hose Reinforcement: High Tensile Steel Wire Certification: ISO9001 Size: 10-38mm(3/8-1 1/2inch) Cover: Weather Resistant Synthetic Rubber Type: hydraulic rubber hose
EN854-2TE Hydraulic Hose with Oil and Weather Resistant Cover CONSTRUCTION: This hose shall consist of an oil and water resistant synthetic rubber lining,two of suitable textile yarn and an oil and weather resistant synthetic rubber cover. APPLICATION: Hydraulic fluids in accordance with ISO6743-4 with the exception of HRD R, HFD S, and HFD T at temperature range of -40~+70 EN854-2TE hydraulic hose: is similar to EN854-1TE hydraulic hose in application. It is also used to handle hydraulic fluids in accordance with ISO6743-4 with the exception of HRDR, HFDS and HFDT. And the temperature of hydraulic fluids ranges from -40C to +100C. It is composed of three parts: tube, reinforcement and cover. Tube is made from oil and water resistant synthetic rubber, making hose perform well in delivering hydraulic oil. Reinforcement is made from one layer of high tensile textile fiber braid, making hose bear high working pressure. Cover is made from oil and weather resistant synthetic rubber, making hose suitable for harsh working environment and have long service life. EN854-2TE hydraulic hose can bear high working pressure because of its high tensile textile fiber braid reinforcement. EN854-2TE hydraulic hose is suitable for harsh working environment for its oil and weather resistant synthetic rubber cover. The details of EN854-2TE hydraulic hose: Structure: it is composed of three parts: tube, reinforcement and cover. Tube: oil and water resistant synthetic rubber. Reinforcement: one layer of high tensile textile fiber braid. Cover: oil and weather resistant synthetic rubber. Temperature range: -40C to +100C. Hose ID: 4.76 mm - 25.4 mm.
EN854-2TE Hydraulic Hose with Oil and Weather Resistant Cover CONSTRUCTION: This hose shall consist of an oil and water resistant synthetic rubber lining,two of suitable textile yarn and an oil and weather resistant synthetic rubber cover. APPLICATION: Hydraulic fluids in accordance with ISO6743-4 with the exception of HRD R, HFD S, and HFD T at temperature range of -40~+70 EN854-2TE hydraulic hose: is similar to EN854-1TE hydraulic hose in application. It is also used to handle hydraulic fluids in accordance with ISO6743-4 with the exception of HRDR, HFDS and HFDT. And the temperature of hydraulic fluids ranges from -40 C to +100 C. It is composed of three parts: tube, reinforcement and cover. Tube is made from oil and water resistant synthetic rubber, making hose perform well in delivering hydraulic oil. Reinforcement is made from one layer of high tensile textile fiber braid, making hose bear high working pressure. Cover is made from oil and weather resistant synthetic rubber, making hose suitable for harsh working environment and have long service life. EN854-2TE hydraulic hose can bear high working pressure because of its high tensile textile fiber braid reinforcement. EN854-2TE hydraulic hose is suitable for harsh working environment for its oil and weather resistant synthetic rubber cover. The details of EN854-2TE hydraulic hose: Structure: it is composed of three parts: tube, reinforcement and cover. Tube: oil and water resistant synthetic rubber. Reinforcement: one layer of high tensile textile fiber braid. Cover: oil and weather resistant synthetic rubber. Temperature range: -40 C to +100 C. Hose ID: 4.76 mm - 25.4 mm.
Overview API Rotary Drilling Rubber Hose for Oilfield steel wire spiral 1.CONSTRUCTION: It is composed of an inner rubber protection layer, middle rubber layer, steel wire spiral layer and external rubber cover. 2.APPLICATIONS: Steel wire spiral drilling rubber hoses are used in oil fields, well cementing, well repairing, geological explorations, small drilling machine, and water conveyance at coal excavations. Used to carry slurry, water at environmental temperature, and other fluids. 3.Execution Specification: API SPEC 5CT, API SPEC STD 5B, API RP 5C1, API RP 5A5, API RP 5B1, API BUL 5C3 SY/T 6194-2003, GB/T 9253.2-1999, GB/T17745-1999, SY/T 6474-2000, GB/T18052-2000, SY/T 6328-1997
R17 ISO 11237-1 R17 SAE J517 R17 Inner tube: Oil resistant synthetic rubber Reinforcement: One braid of high-tensile steel wire(sizes 1/4,3/8 and 1/2)and two braids of high-tensile steel wire(sizes 5/8,3/4 and 1) Cover: Environment resistant synthetic rubber Temperature Range: - 40 F to 212 F(- 40 C to 100 C) Application: High pressure hydraulic applications and to replace 100R1 where higher pressures and a more flexible hose is required.
Sae 100 r2at flexible high pressure hydraulic rubber hose Executive standard:sae 100 r2at / din en 853 2sn standard Construction: Inner tube:oil resistant synthetic rubber. Reinforcement:two high tensile steel wire braid. Cover:â abrasion and weather resistant synthetic rubber. Temperature range:-40â° c to 120â° c. � Application: Double wire braid: recommended for hydraulic system service with petroleum and water-base fluids, or general industrial service. Long-lasting cover is suitable for many mobile hydraulic applications. Meets or exceeds all sae 100r2 at hydraulic hose specifications. Competitive advantage: 1-professional manufacturer of various rubber/hydraulic hoses 2- we have been cooperate with many famous foreign companies and to be there oem factory for many years. 3-we have advanced equipment, experienced engineers and workers. 4-certificates: iso 9001: 2008 5- free samples can be offered 6- good quality, competitive prices and timely delivery and first-rate service.
