The stone production line is composed of vibrating feeder, jaw crusher, impact crusher, vibrating sieve, belt conveyor and computer controlling board; its design output veries from 50 tons to 500tons per hour. In order to meet the needs of different clients, cone crusher and dust collecting equipment can be added to the prodution line. It can be used in industry like hydroelectricity, building materials, express way, city construction to operate the aggregate of hard limestone, granite, pebble, slag of metallurgy and man-made sand. We can combine different model of machines in the production line according to different technical process. Brief introduction of the stone production line Big block of stone is evenly conveyed to jaw crusher by vibrating feeder via silo for primary crushing. After primary crushing, the stone is sent to impact crusher by belt conveyor for secondary crushing. Then the stone is tronsported to vibrating sieve for screening, thus the stone can be classified into several groups depending on the size. The stone with a necessary size will be sent by belt conveyor to the palce where finished product is piled; otherwise, the stone will be conveyed by belt conveyor to the impact crusher for another crushing, thus a circular production process is formed. Introduction of stone production line performance This production line is highly automatic, except the turning on, turning off and daily maintenance of the equipments no other mannual operations are needed. It enjoys the advantages like: high efficiency, low cost, high throughput, high profit, evenly-sized and good-shaped finished product, meeting the national requirements of rapid need of raw materials.
1.Leading Rack Drive, fast, high efficiency, air-speed can reach 35 m / min or more, against the wave plate is carved in manufacturing can be up to 20 m / min above the speed equivalent to the purchase of 4 -- 5 ordinary type machines. 2. Intelligent protection work table: Prevention of misoperation or software errors, and so on the surface may cause damage. Intelligent processing of cross-border protection: preventing processing format over the layout design of mechanical collision caused the phenomenon. 3. Fully in line with international standards: can use any CAD / ArtCAM software and other relief. 4. Advanced DSP control handle, control automatically processing multiple levels 3 D. To carry out rapid, smooth 3D processing, carving or cutting. Offline operation can be realized. 5.The overall program structure welding tempering aging treatment, is not strong deformation. Gantry mobile, fixed working table can be arbitrary processing work table material. 6. Suitable for a variety of materials processing large quantities of production. 7.Take the water cooling system for marble tool when works for marble ,granite ,stone and so on. Performance Parameter: DM-1325S X,Y working area 1300mm*2500mm Z working area 200mm Table Size 1480mm*3000mm Max. Speed 25m/min working holding keep plate CPU DSP/100MHZ Interface USB Command G code*.u00*.mmg*plt Power(not include the spindle) 1840W Work Mode Steper (servo is option) Work voltage 380V/50Hz Spindle power 4.5kw Power vacuum pump 5.5kw Spindle rotating speed DSP. Packed in wooden case; weight 1200 kg.
SCL series sand-stone granulating machine is developed and manufactured on the basis of SX sand making machine, choosing various ore and rock of which compression strength is not more than 300MPa to granulate. Different units of rotary speed and motor power are available according to customers'requirements. Under the condition of increasing rotary speed, sand stone granulating machine can be changed easily to sand making machine according to users' demands. And its most spare parts can be exchanged with SX series sand making machine. The Calculation of Sand-stone Granulator 1. The determination of treating capacity Calculate as following formulas: Q=3600Aª-Vª+2R t/h Aí¬í¬Compensating coefficient 0.7í½1.2t/m*h Take small valve when high rotation speed and take large valve when low rotation speed. ª-í¬í¬Material density t/m3 Ví¬í¬Total volume of rotor exit m3 V=mV1 mí¬í¬Rotor exit number V1í¬í¬Volume of unit exit m3 ª+í¬í¬Circle frequency of rotor rotation ú¿radianú¬ ª+=2ª-n/60 ní¬í¬Rotor rotation speed r/min Rí¬í¬Rotor semidiameter m 2. The determination of motor power The machines of same spec can choose different motor power to meet different demands. Therefore, the determination of motor power is just a range. Generally speaking, express as following formulas: N=ª¦ú¿0.03í½0.15ú¬D2n kW Ní¬í¬Motor power kW ª¦í¬í¬Compensating coefficient 0.8í½1.8m2r*kW/min It is depended on the diameter, the larger diameter, the higher ª¦ value. Dí¬í¬Rotor diameter m ní¬í¬Rotor rotation speed r/min
The motor drives the rotor rotate of the hammer crusher at a high speed through the belt, and on the rotor there are series hammers, when the material get into the working areas of hammers, they are crushed by the rotating hammers of the hammer crusher with high rotation speed, the products which a re crushed to meet the required size can be discharged by the outlet and become the final products, the large size products are brought back to the crushed area by the hammers of the hammer crusher for being re-crushed until they reached the required size. 1. Work hammer, the use of new technology casting, with wear-resistant, impact-resistant. 2.According to customer requirements, adjust the required size. 3.Hammer broken body structure sealed to solve the dust pollution in the crushing plant and body leakage problems. 4.Overall design handsome in appearance, compact structure, less wearing parts, easy maintenance, etc., is upgrading products. 5.Compact structure, beautiful appearance, good wear resistance, easy maintenance.
Application in processing tiles, stones and other building materials.Water cutter is applied in this field much earlier. Currently, the overwhelming majorityin this area use it. They focus on artistic matching. At present, tile matchingand stone matching have expanded all over the world. It is the best way to use water cutter to process tiles. It largely improved productionefficiency and processing precision. It achieved an epochal progress of tilesfurther processing, as it said good bye to the traditional ways of manual grindingand polishing. Presently waterjet cutting is mainly used to make all kindsof complex tile or marble matching . Simple packing.
Characteristicï¼? 1.leading Rack Drive, fast, high efficiency, air speed can reach 35 m / min or more, against the wave plate is carved in manufacturing can be up to 20 m / min above the speed equivalent to the purchase of 4 -- 5 ordinary type machines. 2. intelligent protection work table: Prevention of misoperation or software errors, and so on the surface may cause damage. Intelligent processing of cross border protection: preventing processing form at over the layout design of mechanical collision caused the phenomenon. 3. fully in line with international standards: can use any CAD / ArtCAM software and other relief. 4. advanced DSP control handle, control automatically processing multiple levels 3 D. To carry out rapid, smooth 3D processing, carving or cutting. Offline operation can be realized. 5.the overall program structure welding tempering aging treatment, is not strong deformation. Gantry mobile, fixed working table can be arbitrary processing work table material. 6. suitable for a variety of materials processing large quantities of production. 7.Take the water cooling system for marble tool when works for marble ,granite ,stone and so on.
The motor transmits through belt, drives the moving jaw to do periodic motion towards the fixed jaw by the eccentric shaft. The angle between toggle plate and moving jaw plate increases when mobile jaw moving. So the mobile jaw moves towards the fixed jaw. The stuff will be crushed in this process. The angle between toggle plate and moving jaw decreases when moving jaw moves down, the moving jaw moves leaves fixed jaw by pulling rod and spring, the final crushed stuff will be discharged from the outlet. Main Features for China small portable stone jaw crushers machine mini cement plant price 1. Simple structure, easy maintenance; 2. High crushing ratio, even output granularity; 3. High reliability, low investment; 4. Low noise, less dust. 5. Big capacity
Capacity: 3-500 m/ h. Input Size: 120-1020mm. Output Size: 10-300mm. 1. Introduction The Jaw Crusher is widely used in mining, building materials, chemical industry, metallurgy and so on. The Jaw Crusher is suitable for primary and secondary crushing all kinds of minerals and rocks with compressive strength less than 320 MPa. 2. Processed Materials Iron ore, copper ore, gold ore, manganese ore, river stone, gravel, granite, basalt, minerals, quartz, diabase, etc. Applications Mining, metallurgy, construction, highway, railroad, and water conservancy 3. Working principle The motor transmits through belt, drives the moving jaw to do periodic motion towards the fixed jaw by the eccentric shaft. The angle between toggle plate and moving jaw plate increases when mobile jaw moving. So the mobile jaw moves towards the fixed jaw. The stuff will be crushed in this process. The angle between toggle plate and moving jaw decreases when moving jaw moves down, the moving jaw moves leaves fixed jaw by pulling rod and spring, the final crushed stuff will be discharged from the outlet. 4. Advantages (1). Simple structure, easy maintenance; (2). High crushing ratio, even output granularity; (3). High reliability, low investment; (4). Low noise, less dust. All equipments are produced by the professional technicians of our own factory, with best price and high quality. We look forward to cooperating with you.
Fujian jinjiang xianda machinery is the biggest wire saw stone cutting machine factory in china. And specializing stone machine from 1985. Dnfx-1300-1400 computer automatic multi-function profiling linear machine adopts computer profiling line, cutting with double blades, which is specially used for cutting profiling lines, roman column, big column slab and so on for the heterotype stones. Seaworthy packing
Introduction: Cone crusher is suitable for crushing all kinds of ores and rocks above medium hardness. It has the features of reliable structure, high productivity, easy adjustment and economical operation etc. It is widely used in metallurgy, architecture, rock making, chemistry and silicate industry for crushing various mid-hard and hard ores and rocks. The spring system acts as an overload protection system that allows iron to pass through the crushing chamber without damaging the crusher. It uses consistent grease or water for sealing, which separates crushed particles and lubricating oil, and ensures reliable work. The types of crushing chamber depend upon the usage of the final products. The standard type is applied to medium crushing; the medium type is fit for medium and fine crushing and the short head type is fit for fine crushing. Main Features:We supply a wide range of Cone Crushers, for various secondary and tertiary crushing applications, therefore to insure the best and most feasible Cone Crusher type, fit for different plant configurations, designed for the most efficient and economical production and rock down sizing application. Our Cone Crushers are supplied in four general categories, designed for various types of secondary or tertiary applications, both for closed circuit and open circuit configuration: 1.Coarse type application. 2. Fine or medium type crushing. 3. Short head design.4. Super short head for fine crushing application. 5. Continuous Lubrication: This type of crushers are supplied with high capacity external mounted lubrication unit, composed of oil-tank, oil filtering system, high oil temperature shut-down, low oil flow shut-downs and oil flow gauge, which is designed to supply continuous and stable oil, by forced lubrication to the Cone Crusher, for smooth rotation and operation. Cone Crushers are configured with many safety features. The lubricating unit is interlocked with the main motor, in order to provide additional safety, which includes oil filtration and automatic shut-down in the event of high oil temperature, as well as low oil flow. Crushers are configured with Spring-Loaded release system, which allows any inscrutable material to pass through the crusher, without causing damage to the crusher. The locking system (manual or hydraulic), will easily secure the crushing clearance. All models are configured with proven spring-type mechanism, in order to recover Tramp-Iron and provide protection to the unit. Applications :Cone crusher is a kind of crushing machine commonly used in mining, metallurgical industry, construction, road construction and chemical industry. Our cone crusher can be used to crush hard and medium hard minerals, rocks, iron ores, limestone, copper ores, quartz, granite, sandstones, etc.
