Carbide Sintered Rods with One HoleQuick DetailsParticle:Sub-fine Grain SizeDimensions: OD6.0X330Trade Term: CIF,Website:http://www.mariejcarbide.com,Ground or BlankDelivery Time: 3-20 daysOEM Service: AcceptableTrial Order: AcceptableProduct DescriptionTungsten carbide rods are manufactured as standards with solid with no holes, one or two holes, straight or twisted to a 30 or 40 degree helix, both unground and precision-finish ground to h6 tolerance. A variety of highest quality carbide grades are available, mainly the industry-standard 0.8 micron 10% cobalt grade, other grade requirements are also welcomed.Detailed images:
Cemented Carbide Rods with Two HolesQuick DetailsParticle:Sub-fine Grain SizeDimentions: OD6.0X330Surface: Ground or BlankGrade: K1, K20, K30, C2, C6, YF06Virgin material:100%Trade term: CIF,EXW,FOBDelivery Time: 3-20 daysOEM Service: AcceptableTrial order: AcceptableProduct DescriptionTungsten carbide rods are mostly applied for drill bits, end mills, and reamers with sub-micron grain grade YG10X, for non-ferrous precision cutting and wood cutting with grade YG6X, and for fiberglass reinforced plastics, titanium alloys, hardened steel with ultra-fine grain grade YG8X, etc. Our Carbide rods have a good shock resistance and bending resistance in use.
Tungsten Carbide Rods For PCB ToolsQuick DetailsGrain Size: 0.6μmLength: 330mmTrade  Term: CIF,EXW,FOBGrade: YL10.2Virgin Material:100%Surface: PolishingTrial Order: AcceptableOEM Service: AcceptableDelivery Time: 3-20 daysProduct DescriptionTungsten carbide rods are mostly applied for drill bits, end mills, and reamers with sub-micron grain grade YG10X, for non-ferrous precision cutting and wood cutting with grade YG6X, and for fiberglass reinforced plastics, titanium alloys, hardened steel with ultra-fine grain grade YG8X, etc. Our Carbide rods have good shock resistance and bending resistance in use.Our Services1.We will try our best to reply our customersâ?? requests within 24 hours.2.We will maintain effective and efficient communications with our
PCB Tungsten Carbide Rods For Micro Drilling BitsQuick DetailsGrain Size: 0.6μmLength: � 30mmTrade Term: CIF,Website:http://www.mariejcarbide.com,EXW,FOBGrade: YL10.2Virgin Material:100%Surface: PolishingDelivery Time: 3-20 daysOEM Service: AcceptableTrial Order: AcceptableProduct Description1. Various grades and dimensions with virgin material.2. Fast lead time with stable and good quality.3. Ungrounded and precision rods are all available.Tungsten Carbide Rods' Grades and PropertiesGradesISO CodeCobalt Content %DensityHardnessK10TK-5-K104.5-6.014.95-15.0592.7YG8K30814.889.5YG6K20614.9590.5YG6XK106149591.5YL10.2K301014.591.8YG13XK30-K401314.389.5YG15K40151487.5
Supplier: Carbide rod, carbide cutting tools, carbide dies, carbide mining tips, carbide inserts, carbide wear parts
custom all kinds of tungsten carbide wire drawing die, based on your drawing.
Wire drawing is a metalworking process used to reduce the cross-section of a wire by pulling the wire through a single, or series of, drawing die(s). There are many applications for wire drawing, including electrical wiring, cables, tension-loaded structural components, springs, paper clips, spokes for wheels, and stringed musical instruments. Our drawing dies are made of high purity tungsten powder the size area are 20% longer than common mould,these factors make sure our wire drawing dies can work longer! we can also produce the following types:Z11,w.v.s13,S12,S10,S01,L,13,11 Note: Other specification can be made upon customer's requirements.
1/ GENERAL INTRODUCTION OF TUNGSTEN CARBIDE DRAWING DIES: Tungsten carbide wire drawing dies, wire coating dies, PCD dies for drawing use for drawing various ferrous and nonferrous wires tungsten carbide dies tungsten carbide drawing dies tungsten carbide nibs tungsten carbide wire guide dies PCD dies Both carbide dies nibs and finished products with steel case are supplied
Application: Electronic, Hardware, Car, Stamping Mould Processing Method: Grind, Wire Cut Process Combination: Progressive Die Driving Motor Type: Permanent Magnet Milling Speed: High Speed Size: 8mm*10mm*20mm Hole Tolerance: +/-0.003 Origin: Origin in Dongguan China Material: Tungsten Carbide Technics: Cutting Die Manufacturing Technology: Automation Technology Mold Cavity Technology: The Traditional Forming Electrode Machining Parts Detection Method: Geometric Detection Life Time: 3 Years Specification: Non-Standard, Standard, 8mm*10mm*20mm
