IC card cavity milling machine and chip embedding machine SICMP-01 is an all-in-one machine perfect for contact card production, it is able to do card milling, glue tape lamination, module embedding. perfect for small scale mass production Perfect for a wide range of smart card prodcution needs where speed, flexibility and high efficiency are required. Smart Card cavity milling machine and module embedding machine Dimension L 3620mm X W 960mm X H1750mm Weight 2100KG Power AC380V,50Hz ( Depends on country ) Rated power 8KW Air Pressure 6KG/CM² Air consumption 180l/min Control type PLC+Servo motor system Production speed 3200pcs/Hour
SICM-06 is to do milling process, for high speed milling, this machine is perfect choice. Perfect for a wide range of smart card prodcution needs where speed, flexibility and high efficiency are required. High Speed Card Milling Machine Dimension L 3620mm X W 960mm X H1750mm Weight 2100KG Power AC380V,50Hz ( Depends on country ) Rated power 8KW Air Pressure 6KG/CM² Air consumption 180l/min Control type PLC+Servo motor system Production speed 3200pcs/Hour g machine
Item Technical Parameters Size L3410mm X W1760mm X L1900mm Weight 3000Kgs Power 14.5kw Compressed Air 5kgf-7kgf/cm(0.5Mp-0.7Mp) Dry, without water Air Consumption 250L/min Applicable Range H2~40mm, W70~220mm, L 150~300mm Electrode tab range W20~70mm, L6~30mm Cell Thickness 5-40mm Speed 0.5s/pcs / dual-station(1s/pcs / single station) End Roll Timing 10-15s Pole Piece Positioning Accuracy ±0.3mm Membrane Positioning Accuracy ±0.3mm( Excluded end roll membrane) Membrane Spec Thickness 15-30 µm, Inner diameter 76mm, Max outer diameter 300mm Adhesive tape Spec Thickness 15-30 µm,W10-20mm, Inner diameter 76mm, Max outer diameter 150mm Adhesive tape Speed Adhesive tape 10 stripes with 20s
AINiCo is composed primarily of Aluminum Nickel Cobalt and also Copper and Titanium. They are manufactured through either casting or sintering process. Cast AINiCo may be manufactured in complex shapes such as horseshoes not possible with other magnet materials. Sintered AINiCo offer slightly lower magnetic properties but better mechanical characteristics. it can be efficiently magnetized in any direction, and for anisotropic AINiComagnet, it generally has greater magnetic capacitive in a preferred orientation than isotropic types. AINiCo is hard and brittle, Machining or drilling cannot therefore be accomplished by ordinary methods. Holes are usually cored in at the foundry, and magnets are cast close to final size and then finish machined to closer tolerances. â?¢ Advantages of AlNiCo Magnet: 1.Customized designs are available. 2.Max working temperature can be as high as 550�°C. 3.Disadvantage: Br and BH(max)are not as high as rare earth magnet. 4.High energies and relatively low coercivity. 5.High magnetic flux density; low mold charge stable temperature properties; easy to shap.
Samarium Cobalt (SmCo) magnets are made by a sintering process and exist in two forms. The first is Sm1Co5(SmCo 1:5),which has a maximum energy product of between 14 and 24MGOe. The second and more common form is Sm2Co17(SmCo 2:17) which has a maximum energy product of between 22 and 32 MGOe. The main Sm2Co17 alloy is around 35% Samarium (Sm)and 60% Cobalt (Co)with the balance being from varying amounts of lron (Fe) Copper (Cu). Hafnium (Hf) and Zirconium (Zr). Praseodymium (Pr) may also be used. Sm1Co5 is made of only Sm and Co and has excellent corrosion resistance. â?¢ Advantages of SmCo Magnet: 1.Superior resistance to high temperature. 2. Excellent resistance to corrosion, no coating is needed for surface protecting. 3.High working temperature. 4.SmCo is suitable for machines with high magnetic requirements and good for strict working environment requirement.
Ferrite Magnet is manufactured from oxide material by powder metallurgical process. Its advantages include: low-cost excellent corrosion resistance, resistance to be demagnetized etc. The normal working temperature of Ferrite Magnet is between-40C and +250C.It can be magnetized before or after assembling. Generally, Ferrite Magnet can be machined to regular shapes like segments, blocks, rings and discs etc. The normal grades for sintered Ferrite Magnets are Y10,TY25, Y30, Y30BH, Y35, etc. Advantages of Ferrite Magnet: Ferrites have isotropic characteristics, weak magnetic performance, has the same magnetic performance in any direction, multipolar magnetic charge. The main raw material of ferrite is oxides, so it is not corroded by high temperature, high humidity or chemicals (except strong acid and base); with excellent diamagnetic impedance, no flux loss before and after assembly and magnetic charging; working temperature is-40C to + 250C, poor temperature coefficient; Br temperature coefficient is-0.2% /C, 0.2% under Br, etc. per 1 Cincrease; high hardness, wire cutting and grinding; ferrite is brittle and fragile during production and transportation. magnetic requirements and good for strict working environment requirement.
Supplier: Chemicals, minerals, agro products, steel, aluminium, copper, scaffolding products, minerals, scrap, washing machine parts, refrigerator parts, micro oven parts & auto parts.
Buyer: Chemicals, minerals, agro products, steel, aluminium, copper, scaffolding products, minerals, scrap, washing machine parts, refrigerator parts, micro oven parts & auto parts.
We are a supplier of used and new Heidelberg printing machine, parts and consumables globally , we acknowledge the demand of offset products and we want to fill that gap by bringing to the world the best affordable quality offset products.
Automatic dough plate setting machine shelving machine all-in-one machine, Use bionic technology to complete automatic dough plate setting and automatic shelving, which is more convenient, efficient and sanitary for the next processing, and saves labor costs. Capacity 3600pcs/hour,dough weight can adjustable,220V/0.75kw . .1person can operation ! welcome order !
