A conveyor belt is a looped belt that is driven by and wrapped around one or more pulleys. It is powered by an electric motor and supported by a metal plate bed or rollers upon which the conveyor belt rests. The pulley that powers a conveyor belt is referred to as the drive pulley and has an unpowered idler pulley.
Our roller coatings provide a stable grip, are long-lasting, and resistant to damage from high temperatures, abrasion, oil, and chemicals. The majority of coverings are available with a self-adhesive backing that is high-heat resistant, guaranteeing a high level of adhesion to the roller. In addition, we provide non-adhesive roller covering tape with a selection of very fine specialty contact adhesives. Depending on the purpose, a variety of materials are used to create our roller covers.
Supplier: Ethanol /alcohol process line/machine,ethanol/alcohol turnkey project , industry fruit process machine/production line ,industry vegetable process machine/production line, industry noodle machine/production line , industry bread/cake machine/process line and so on . industry waste water treatment system process line .packing machine
Services: Our company's products, technical support, training, installation and commissioning
* PHOSCAST Phoscast : Phosphate Bonded Castables * PURPOSE customers using FBC boilers (Particularly underbed feed FBC boilers) for the protection of inbed coils against erosion potential by applying highly abrasive resistant refractory on inbed coils above fuel feed system. BACKGROUND * Two of such actions are providing special alloy studs on inbed coils and applying highly abrasive resistant refractory on the outer bottom loops of inbed Coils which are above the fuel feed nozzles. * GANESHAS has taken number of approaches to identify the key factors affecting erosion rates with an objective to enhance the life of inbed tubes as well as implementing the corrective action to reduce the erosion rates. Phosphate coatings are often used to protect steel parts against rusting and other types of corrosion * Erosion of inbed coils in fluid bed combustor is unavoidable phenomenon however the rate of metal wastage and thus the life of tubes depends on various factors like ash & fuel properties, design of Combustor / feeding system, flue gas velocities operating conditions etc. It has been also observed that maximum erosion prone inbed coils are those which come above fuel feed nozzles and an area of approximately 1 to 1.5 mts around fuel feed systems are badly affected. APPLICATION Phoscast-90 XR can be applied by ramming with wooden mallet having adequately large head @" dia x 5" length x 10â?? Jong handle). The desired lining or repair thickness is built up in several courses while ramming the mass to uniform thickness. Phoscast refractory should never be trawled to obtain smooth surface; ramming only should finish surface. Any excess mass is to be sliced off with trowel edge and then finished by ramming again for bed coil. Tube application of AFBC boiler, the material pasty mass should be finger pressed into the studs of the tube with maximum force. Finish should be given by pressing the hand palm against material applied, using surgical type thin rubber hand gloves.
We supply the Quality Ferro Alloys Like Ferro Manganese HC / MC / LC Grade I II III Mn 65% min 70% Min 75% Min Si 2% Max 2% Max 1.50% Max C 8% Max 8% Max 8% Max S 0.05% Max 0.035% Max 0.03% Max P 0.40% Max 0.30% Max 0.25% Max MC FeMn Mn 70%Min /75% Min / 78% Min Si 1.50% Max C 1.50% MAX S 0.03% Max P 0.25% Max Ferro-Manganese Ferro-Manganese is an alloy with high percentage of Manganese, which is made by heating a mixture of the oxides MnO2 and Fe2O3 and coal & coke with high carbon content in a blast furnace or an electric arc furnace-type system. The oxides go through carbothermal reduction in the furnaces that result in producing the Ferro-Manganese. Ferro-Manganese is used in the production of steel which acts as an excellent deoxidizer and desulfurizer. We supply the one variant of Ferro Manganese: High Carbon Ferro-Manganese.
We deals in the following products of India, China, Taiwan and Korea Origin:- 1) Hot Rolled Steel (Hot Rolled Sheets, Hot Rolled Coils, Hot Rolled Plates, Hot Rolled Bars etc.) 2) Galvanized Steel (Galvanized Steel Tapes, Galvanized Steel Wires, Galvanized Steel Strips, Galvanized Steel Coils, Galvanized tubes etc.) 3) Cold Rolled Steel (Cold Rolled Steel Strips, Cold Rolled Steel Coils, Cold Rolled Sheets etc.) 4) Stainless Steel (Stainless Steel Strips, Stainless Steel Coils, Stainless Steel Wire, Hardened and Tempered Spring Steel, Stainless Spring Steel, Spring Steel Wires etc.) 5) Steel Tube and Pipes (ERW, CRW, CRS, Black, Galvanized, Stainless) 6) Forged Column Clamps, Girder Clamps, Pressed Clamps, Rapid Clamps, Support Clamps & Wedge Clamps. 7) Heavy Duty Props & Light Duty Props. 8) Nuts, Bolts, Nails & Fasteners 9) System Scaffolding, Base Plate & Adjustable Base. 10) Steel Tie Rod, Waller Plates and Wing Nuts. 11) Drop Forged and Pressed Sheet Metal Couplers of all types. 12) Steel Billets, Steel Angle & Steel Channels. Price: After receiving complete details