Appearance:colorless transparent liquid
Viscosity at 25ºc, mm² per s: 165
Diopter at 25 ºc: 1.09 min.
Specific gravity: 1.090~1.100
Flash point, ºc: 243 min.
Condensation point, ºc: -14~-18 max.
Ultimate vacuum, pa: 6.6*150-7 max.
Saturated vapor pressure, pa: 6.65*10-8 max
200kg iron drum, 25kg or 50kg plastic drum, 950kg ibc drum.
Property and usage:
275# silicone oil for super high vacuum diffusion pump is colorless, transparent oily fluid and owns very low saturated vapor pressure, good heat resistivity property and with excellent resistance to high temperature, oxidant and radiate. It can be used in high vac., electrical industry, coating for high vac., particle accelerator, electronic microscope and display, etc.
KT, K series oil diffusion pump is the main pump used to obtain high vacuum (2 ~ 10-10-5 pa)t. It can be combined with water-cooled plate, pipe, valves and mechanical vacuum pump together and becoming high vacuum system, the ultimate pressure can be up to (2 ~ 10-10-4 pa) .
If it takes liquid nitrogen cooling device with baking, the vacuum can be up to the ultra high vacuum10-6 (pa).
The characteristic of the pump is strong pumping ability, Large pumping capacity from 480 to 130000 l/s are suitable.
It has Observation window, oil filling port and discharge port, pump oil measurement device.
The products take stretching technology on manufacturing, reducing weld, increasing strength, reducing the discharge volume. Heater is equipped either with heating wire or electric heating plate, you can choose when you order it.
Application:
It is widely used in vacuum coating, vacuum furnace, electronics, chemical industry, aviation, aerospace, metallurgy, material, biological medicine, atomic energy, space exploration and other high-tech fields, and it has also been widely used in titanium sponge field with high praise.
We are waiting for your news for getting detailed information about our pumps.
KTN/ KN series Diffusion Pump ( Internal heating type)
KN /KTN series are the equipment mainly used for getting the high vacuum condition(10 -10 Pa-10-5Pa);
The pumping capacity can be reached from 3100L/s to 110000L/s,it adds observation windows,oil inlet and outlet,the protection device of controlling pump oil overheat,the alarm device of controlling cooling water overheat,and parallel combination of many heating rods insert into the pump,the heating rods can be replaced without shutting down the
machine,so heat time will be shorten .
Low oil vapor back-streaming rate so then can be working without external water cooling baffle.
When using the common pump oil,the return volume is 1Ã?10-3mg/cm2·min .when using 275 silicon oil, it will be reduced to 1Ã?10-4 mg/cm2·min , ultimate vacuum is less than 10-6Pa.
The pump adopts stretching process,reduces weld crack and out-gassing and increases strength.
It is widely used in vacuum coating,vacuum furnace,electron,aviation,aerospace and other High-tech fields.
V4 Borewell Submersible Pumpset
Falcon Premium 100 mm (4) Borewell Submersible pump is firmly coupled to a submersible electric motor and Operates by being submerged beneath the surface of the water. The optimal design of impeller and diffuser enables the best Possible hydraulic efficiency. Built-in check valve prevents back flow and reduces the risk of water hammering. All Vital components of these pumps are made up of corrosive resistance thermoplastic and the shaft is of SS 410.
Salient Features
- Motor portion covered with corrosive resistance Stainless steel J4 shell
- More durability and hygiene
- High operating efficiency
- Specially designed thrust bearing to withstand high axial thrust load
- Extremely hardwearing water lubricated bearing
- Thread type motor construction ensures service feasibility
- Specially designed Deep Drawn type pump ensures perfect alignment and
Thereby increases the life of the pump set
- Designed for wide voltage operation
- Best alternative for JET & Compressor pump set
- Additional intermediate bearing in higher stage pumps.
Specification
Power Range : 0.37 kW to 4.4 kW (0.50 HP to 6.0 HP)
- Version : Single Phase 160V to 230V, Three Phase 350 to 415V, 50Hz AC Supply.
Single Phase available in 0.5 HP to 5.0 HP
Three Phase available in 1.0 HP to 6.0 HP
- Speed : 2880 RPM
- Head Range : 10 Mtr. To 340 Mtr.
- Discharge Range : 450 LPM to 12 LPM
- Outlet Size in Inch : 1.0 , 1.25, 1.5 & 2.0
- Degree of Protection : IP 58
- Direction of Rotation Minimum Cooling : Counter clockwise from driving end -1ph: Electrically Reversible -3ph
- Thrust Load : 0.37 kW â?? 0.75 kW- 650 lbs, 1.1 kW -1.5 kW -1000 lbs,
2.2kW, 7.5 kW -1500 lbs.
- Flow Along the Motor : 0.15 m/sec.
- Type of Duty : S1 (Continuous)
- Method of Starting : 1ph-Capacitor Start Capacitor Run (CSCR): 3ph
Direct Online (D.O.L)
- Maximum Starts Per Hour : 20 Times
Falcon standard 73mm (3") Borewell Submersible pump is firmly coupled to a submersible electric motor which Operates by being submerged beneath the surface of the water. The optimal design of impeller and diffuser enables the best Possible hydraulic efficiency. Built-in check valve prevents back flow and reduces the risk of water hammering. All Vital components of these pumps are made up of corrosion resistance thermoplastic and the shaft is of SS 410.
Salient Features
- Motor portion covered with corrosive resistance Stainless steel (SS 204cu) shell
- More durability and hygiene
- High operating efficiency
- Specially designed thrust bearing to withstand high axial thrust load
- Extremely hardwearing water lubricated bearing
- Thread type motor construction ensures service feasibility
- Specially designed Deep Drawn type pump ensures perfect alignment and Thereby increases the life of the pump set
- Designed for wide voltage operation
- Best alternative for JET & Compressor pump set
- Additional intermediate bearing in higher stage pumps.
Specification
- Power Range : 0.37 kW to 1.1 kW (0.50 HP to 1.5HP)
- Version : Single Phase 160V to 230V, 50Hz, AC Supply
- Speed : 2880 RPM
- Head Range : 14 Mtr. to 96 Mtr.
- Discharge Range : 70 LPM to 15 LPM
- Outlet Size in Inch : 1.25"
- Degree of Protection : IP 58
- Direction of Rotation : Counter clockwise from driving end -1 pH Minimum cooling 1pH
- Flow Along the Motor : 0.15 m/sec.
- Type of Duty : S1 (Continuous)
- Method of Starting : 1ph-Capacitor
- Maximum Starts Per Hour : 20 Times
Characteristics Of Clear Cold Water
- Maximum liquid temperature : 33C max
- Permissible amount of sand : 25 g/m
- Allowable solids : 3000 ppm (max.)
- Chloride ion density : 500 ppm (max.)
- Turbidity : 50 ppm silica scale (max.)
- Hardness (Drinking Water) : 300 ppm (max.)
- Specific gravity : 1.004 (max.) 6
- Viscosity : 6 1.75 x 10 m�²/sec (max.)
- Ph Value : 6.5 to 8.5
