Our Advantage: 1.Available in 5 ft.and 10ft. lengths; 2.Elector Zinc Plated for a professional look; 3.Full line of accessories are available to mount on the wall,from the ceiling or under he door; 4.Cuts easily with bolt cutter for custom configurations; 5.Cable Trays bolt together to any custom configurations; 6.Stackable Cable Guides available to separate and secure cables in place; 7.Complete line of accessories available. Certificate CE, CUL, ROHS, ISO, SGS Material Q235, SS304, SS316 Surface Finish Electro Zinc,Hot Dipping, Powder Coating Width 50mm, 100mm, 150mm, 200mm, 300mm, 400mm, 600mm, 800mm Height 30mm, 50mm, 100mm, 150mm, 200mm Diameter 4mm, 5mm, 6mm Length 3000mm Application Data Center, Communication Room, Financial Industry Room, Government Office and so on...
Brief Introduction of Wire Mesh Cable Tray Systems: These are thicker and therefore stronger than apparently similar products. Cablofil incorporates a unique T welded safety edge resulting in performance comparable with traditional cable tray but with many added benefits. Features and Benefits of Wire Mesh Cable Trays: 1. Electroplated Zinc Finish 2. Fast Easy Installation 3. Mesh Design Allows Cable Exit or Entry at any point 4. Clear Cable Identification 5. Supplied in 3 Metre Lengths 6. Significant Cost Savings Compared to Standard Tray Products 7. Simple Creation of Fittings on Site 8. Wide Range of Sizes 9. Heights Shown are Internal Dimensions Manufacturing: Optional Material for wire mesh cable tray: Black Steel, Stainless Steel, Aluminium, Alloy, Fibreglass Reinforced Plastic (FRP) Mode: Top curved / Top Straight Surface Finish: Zinc-plating, Hot-dip Galvanizing (HDG), Powder-coated, Pickled & Passivated. Color: Optional Suggestions: 1). MATERIAL The choice of materials is a matter of the physical and mechanical properties produced by each, compared against the intended function, as well as the environment, in which the trays are to be installed. 2). SURFACE FINISH: A). Zinc-plating cable trays are suitable for indoor use. The place where cold zinc-plating cable trays would work should be dry, ventilated, and corrosion free. B). Hot-dip Galvanizing (HDG) cable trays are not suggested for wire mesh cable trays. C). Powder-coated cable trays should be carried out in alkali and salt corrosion free site. D). Pickled & Passivated should be used to stainless steel wire trays. Specification for power and communications cabling containment. 1). SCOPE Steel Wire Cable Tray conforming to the material and performance of this specification. 2). GENERAL A). Cable tray shall be manufactured from steel wires, welded together and bent into final shape prior to surface treatment. B). Surface Treatments: i). Electro zinc plated to BSEN 12329-2000 for interior use (level 2) ii). Hot Dipped Galvanised with between 60 and 80 microns of zinc to BS 729. iii). Stainless Steel AFNOREZ CND 17.2 (AISI 316L) C). Steel Wire Cable Tray Widths & Depths i). Cable Tray dimensions are all internal. ii). Depths of 30mm, 54mm, 80mm, 105mm & 150mm iii). Widths of 50mm, 100mm, 150mm, 200mm, 300mm, 400mm 450mm, 500mm & 600mm for depths of 30mm & 54mm. iv). Widths of 100mm, 150mm, 200mm, 300mm 400mm & 500mm for Depths of 105mm & 150mm All trays are of 3005mm long 3). SPECIFICATION a). Steel Wire Cable Tray will be produced from lateral and longitudinal sidewall steel wires, with minimum diameters of -: 4 mm for trays of widths up to 150mm 4.5 mm for trays of widths of 200mm 5.0 mm for trays of widths of 300mm 6.0 mm for trays of widths of 400mm, 450mm, 500mm and 600mm b). Trays will be manufactured with a longitudinal 'T-welded' safety edge along the top wire of the sidewall (excluding CF3050) c). Trays will be constructed with a 50mm x 100mm mesh configuration. d). All tray fittings (e.g. changes in direction, level and size) shall be constructed on site, to the manufacturers instructions, using side action bolt croppers and fastened using 25mm and 30mm counter clamps with M6 bolts and nuts, all surface treated as the tray. e). Trays will be coupled together using either a fast spring coupler or a 25mm/30mm counter clamp combination with supporting lateral splice plate on trays over 300mm width. The coupling will have the same surface finish as the tray. f). Trays shall be supported at a maximum span of 2.5m by trapeze, wall, floor or channel mounting methods and will not exceed maximum loads as specified by the manufacturer. g). All welds will be manufactured to an average minimum tensile strength of 500Kg per weld. 4. TESTS, CERTIFICATION AND CONFORMITY a). Loading and deflection characteristics of the tray should be tested and the results published in accordance with the European Standard CEI/61537. b). Suitability for the support of Cat6 data cabling should be demonstrated by way of independent test verification. c). Fire test certification should be published in accordance with the E30/E90 standard. d). Electrical continuity across a coupling should be demonstrated by means of a published test method and result. We are able to design styles in various specifications according to the drawings and/or samples by the clients. And we offer fair price, excellent quality, quick delivery, continuous improvement. We own customer satisfaction. You can trust on us that we are the leading manufacturer of cable trays. PSC
Wire Mesh Cable Tray provides A job site, field adaptable support system primarily for low voltage, telecommunication and fiber optic cables. These systems are typically steel wire mesh, zinc plated. standard widths of 2, 4, 6, 8, 12, 16, 18, 20, and 24 inches standard depths of 1, 2, and 4 inches standard length of about 10 feet (118) Wire Mesh tray is generally used for telecommunication and fiber optic applications and are installed on short support spans, 4 to 8 feet.
Material: Q235B Steel (Chinese standard steel), SS304, SS316 & SS316L Surface Finish: Electro zinc plated ¨C for indoor use to BS EN 12329-2000, 12microns thick. Powder coated - for indoor use to JG/T3045-1998, between 6 and 10 microns thick Hot Dipped Galvanized ¨C for outdoor use to BS EN 1461-1999, between 60 and 80 microns thick Electrolytic Polishing ¨C for stainless steel use Specification: Model D W L WEIGHT WB1.5X4X10 1.5'' 4'' 10' 5.8lbs WB1.5X6X10 1.5'' 6'' 10' 7.4lbs WB1.5X8X10 1.5'' 8'' 10' 9lbs The advantages of our wire mesh cable tray: 1. Low cost, significant cost savings compared to standard traditional tray products. 2. Light in weight, wide range of sizes. 3. Fast heat dispersion. 4. Strong enough to withstand short circuits. Provides strength, rigidity without additional hardware 5. Adapts to difficult architectural designs to accommodate changes in direction and elevation of cable runs. 6. Flexible, easy and fast installation. Design allows cable exit or entry at any point. 7. Cables can be secured to clamps or ties. 8. Various hardware accessories available to fix, support and install. 9. Safe smooth edge design to protect cable 10. Easy for line check and cleaning , easy maintained. All sharp ends are cut off to protect cables. Weight loading capacity is 27% stronger than traditional cable trays and cable ladders. Application: The electric cable tray system are widely used for construction projects, such as layingelectrical wire and cable. Making the lay of the electric wire, electric cable andpipeline achieved the universalized level. Installation Notice: Bends, Risers, T Junctions, Crosses & Reducers can be made from wire mesh cable tray straight sections flexibly in projects. Trays shall be supported at a maximum span of 2.5m by trapeze, wall, floor or channel mounting methods and will not exceed maximum loads as specified by the manufacturer. Wire Mesh Cable Tray systems can be safely employed in places where the temperature ranges between -40C and +150C without any change to their characteristics. Standard packing or customerized packing.
CABLE TRAYS are produced in various sizes from 600 mm width to 100 mm wide with required height. It is supplied with required accessories. standard
Materials: carbon steel and stainless steel (302,304,304L,316,316L etc). Characteristics:The welded stainless steel water well screen is made up of rods and warp. The rod can be round wire, triangular wire or trapezoid wire. The warp is triangular wire (V-shaped wire). Water well screens have a structure and high open area, as well as accurate slot dimension. At the same time, water well screen have heat-resisting, anti-corrosive, good machine capability, last long, safety and reliability and so on characteristics. It can be used in many kinds of medium filtering. Uses: The strainer is a kind of filtered water tubing with the perforation .it can use with the deep well pump, dive the water pump, also may use in the water-treating equipment, the environmental protection, the sea water transforms into the industrial water and life use water desalination treatment, running water treatment, water softening treatment, the petroleum industry: The petroleum product terminal filters and the chemical acid, the alkali liquid filters, the ethyl alcohol and so on the organic solution recycling filters. Continuous slots significantly increase discharge area,thus providing greater access to water-bearing zone . We can produce this pipe with diameter 80mm-550mm ,slot size 0.1mm-10mm,length 50mm-5850mm .
Wireharness for auto, airspace and equipment
Our Quality IBC liner steel cage WIRE MESH FOR IBC TANK FRAME are great steel cage mesh for IBC Frame for use in Hotels, Garment Shops, Building Material Shops, Manufacturing Plant, Machinery Repair Shops, Food & Beverage Factory, Farms, Restaurant, Home Use, Retail, Food Shop, Printing Shops, Construction works , Energy & Mining, Food & Beverage Shops, Other, Advertising Company. The Core Components Includes PLC, Engine, Bearing, Gearbox, Motor, Pressure vessel, Gear, Pump
Size : 6 SWG 14 SWG Zinc Coating : 30- 275 GSM Major application areas are in Poultry Mesh, Chain Link Fencing, Barbed Wires, Galvanized Fencing Wire, Fine Wire Mesh, Trolleys, Baskets, Stranded Ropes, Stay Wires, Bailing Wires, Telegraph / Telephone Wires, Gabbian Mesh Wires etc.
Stainless Steel Wire Mesh is manufactured in both Square & Rectangle openings for different uses. We offer this Stainless Steel Wire Cloth in a wide range of openings and configuration of wire thickness in different types of weaving such as Plain Weave, Twill Weave, Plain Dutch Weave, Twill Dutch Weave etc. Different types of� weaving give you different aperture &� vary the texture from soft & fine to rigid. The Stainless Steel Cloth is usable under high pressure, high temperature, and high tension and gives you high durability. We have wide range of ready stock. Features: Simpleweaving Elegant High quality Specifications: Material:Stainlesssteelwire304l,306l Width:Upto4m Whole size: 2 Mesh to 500 Mesh
