V3 Borewell Submersible Pumpset Falcon standard 73mm (3") Borewell Submersible pump is firmly coupled to a submersible electric motor which Operates by being submerged beneath the surface of the water. The optimal design of impeller and diffuser enables the best Possible hydraulic efficiency. Built-in check valve prevents back flow and reduces the risk of water hammering. All Vital components of these pumps are made up of corrosion resistance thermoplastic and the shaft is of SS 410. Pump Liquids - Clean - Thin - Non-Aggressive - Non-Explosive - Clear - Cold - Fresh water - Without abrasives - Solid particles. Salient Features - Motor portion covered with corrosive resistance Stainless steel (SS 204cu) shell - More durability and hygiene - High operating efficiency - Specially designed thrust bearing to withstand high axial thrust load - Extremely hardwearing water lubricated bearing - Thread type motor construction ensures service feasibility - Specially designed Deep Drawn type pump ensures perfect alignment and Thereby increases the life of the pump set - Designed for wide voltage operation - Best alternative for JET & Compressor pump set - Additional intermediate bearing in higher stage pumps. Specification - Power Range : 0.37 kW to 1.1 kW (0.50 HP to 1.5HP) - Version : Single Phase 160V to 230V, 50Hz, AC Supply - Speed : 2880 RPM - Head Range : 14 Mtr. to 96 Mtr. - Discharge Range : 70 LPM to 15 LPM - Outlet Size in Inch : 1.25" - Degree of Protection : IP 58 - Direction of Rotation : Counter clockwise from driving end -1 pH Minimum cooling 1pH - Flow Along the Motor : 0.15 m/sec. - Type of Duty : S1 (Continuous) - Method of Starting : 1ph-Capacitor - Maximum Starts Per Hour : 20 Times Characteristics Of Clear Cold Water - Maximum liquid temperature : 33C max - Permissible amount of sand : 25 g/m - Allowable solids : 3000 ppm (max.) - Chloride ion density : 500 ppm (max.) - Turbidity : 50 ppm silica scale (max.) - Hardness (Drinking Water) : 300 ppm (max.) - Specific gravity : 1.004 (max.) 6 - Viscosity : 6 1.75 x 10 m�²/sec (max.) - Ph Value : 6.5 to 8.5
V3 Borewell Submersible Pumpset Falcon standard 73mm (3") Borewell Submersible pump is firmly coupled to a submersible electric motor which Operates by being submerged beneath the surface of the water. The optimal design of impeller and diffuser enables the best Possible hydraulic efficiency. Built-in check valve prevents back flow and reduces the risk of water hammering. All Vital components of these pumps are made up of corrosion resistance thermoplastic and the shaft is of SS 410. Pump Liquids - Clean - Thin - Non-Aggressive - Non-Explosive - Clear - Cold - Fresh water - Without abrasives - Solid particles. Salient Features - Motor portion covered with corrosive resistance Stainless steel (SS 204cu) shell - More durability and hygiene - High operating efficiency - Specially designed thrust bearing to withstand high axial thrust load - Extremely hardwearing water lubricated bearing - Thread type motor construction ensures service feasibility - Specially designed Deep Drawn type pump ensures perfect alignment and Thereby increases the life of the pump set - Designed for wide voltage operation - Best alternative for JET & Compressor pump set - Additional intermediate bearing in higher stage pumps. Specification - Power Range : 0.37 kW to 1.1 kW (0.50 HP to 1.5HP) - Version : Single Phase 160V to 230V, 50Hz, AC Supply - Speed : 2880 RPM - Head Range : 14 Mtr. to 96 Mtr. - Discharge Range : 70 LPM to 15 LPM - Outlet Size in Inch : 1.25" - Degree of Protection : IP 58 - Direction of Rotation : Counter clockwise from driving end -1 pH Minimum cooling 1pH - Flow Along the Motor : 0.15 m/sec. - Type of Duty : S1 (Continuous) - Method of Starting : 1ph-Capacitor - Maximum Starts Per Hour : 20 Times Characteristics Of Clear Cold Water - Maximum liquid temperature : 33C max - Permissible amount of sand : 25 g/m - Allowable solids : 3000 ppm (max.) - Chloride ion density : 500 ppm (max.) - Turbidity : 50 ppm silica scale (max.) - Hardness (Drinking Water) : 300 ppm (max.) - Specific gravity : 1.004 (max.) 6 - Viscosity : 6 1.75 x 10 m/sec (max.) - Ph Value : 6.5 to 8.5
V4 Borewell Submersible Pumpset Falcon Premium 100 mm (4) Borewell Submersible pump is firmly coupled to a submersible electric motor and Operates by being submerged beneath the surface of the water. The optimal design of impeller and diffuser enables the best Possible hydraulic efficiency. Built-in check valve prevents back flow and reduces the risk of water hammering. All Vital components of these pumps are made up of corrosive resistance thermoplastic and the shaft is of SS 410. Pump Liquids - Clean - Thin - Non-Aggressive - Non-Explosive - Clear - Cold - Fresh water - Without abrasives - Solid particles. Salient Features - Motor portion covered with corrosive resistance Stainless steel J4 shell - More durability and hygiene - High operating efficiency - Specially designed thrust bearing to withstand high axial thrust load - Extremely hardwearing water lubricated bearing - Thread type motor construction ensures service feasibility - Specially designed Deep Drawn type pump ensures perfect alignment and Thereby increases the life of the pump set - Designed for wide voltage operation - Best alternative for JET & Compressor pump set - Additional intermediate bearing in higher stage pumps. Specification Power Range : 0.37 kW to 4.4 kW (0.50 HP to 6.0 HP) - Version : Single Phase 160V to 230V, Three Phase 350 to 415V, 50Hz AC Supply. Single Phase available in 0.5 HP to 5.0 HP Three Phase available in 1.0 HP to 6.0 HP - Speed : 2880 RPM - Head Range : 10 Mtr. To 340 Mtr. - Discharge Range : 450 LPM to 12 LPM - Outlet Size in Inch : 1.0 , 1.25, 1.5 & 2.0 - Degree of Protection : IP 58 - Direction of Rotation Minimum Cooling : Counter clockwise from driving end -1ph: Electrically Reversible -3ph - Thrust Load : 0.37 kW â?? 0.75 kW- 650 lbs, 1.1 kW -1.5 kW -1000 lbs, 2.2kW, 7.5 kW -1500 lbs. - Flow Along the Motor : 0.15 m/sec. - Type of Duty : S1 (Continuous) - Method of Starting : 1ph-Capacitor Start Capacitor Run (CSCR): 3ph Direct Online (D.O.L) - Maximum Starts Per Hour : 20 Times
Falcon Premium 200 mm (8) Borewell Submersible pumpsets are powered by water filled, rewindable submersible motor suitable for continuous duty. The stator is wound with special water proof synthetic film insulated copper winding wires and made up of low watt loss silicon steel laminations assembled under pressure and rigidly locked in stainless steel stator shell. Pump Liquids - Clean - Thin - Non-Aggressive - Non-Explosive - Clear - Cold - Fresh water - Without abrasives - Solid particles. Salient Features - Specially designed Deep Drawn type pump ensures perfect alignment and Thereby increases the life of the pump set - SS-304 Grade investment casting bowl and SS-304 grade impeller in radial flow series - 20 Mtr. Head per stage in radial flow series - Specially designed high performance thrust bearing (SS-420 Tilting pad with carbon plate) to with stand axial thrust loads - Dynamically balanced rotating parts ensures minimum vibration and longer life - Motor portion covered with corrosive resistance Stainless steel J4 shell - More durability and hygiene - High operating efficiency - Special designed thrust bearing to withstand high axial thrust load - Extremely hardwearing water lubricated bearing - Thread type motor construction ensures services feasibility - Designed for wide voltage operation - Best alternative for JET & Compressor pump set - Additional intermediate bearing in higher stage pumps - Fully SS Pumps are available Specification Direction of Rotation : Counter clockwise from driving end -1ph : Electrically Reversible -3ph - Power Range : 7.5 kW to 75 kW (10 HP to 100 HP) - Version : Three Phase 350 to 415V, 50Hz AC Supply - Thrust Load : 7.5 kW -30 kW -10000 lbs - Speed : 2880 RPM - Head Range : 12 Mtr. To 440 Mtr. - Discharge Range : 2400 LPM to 300 LPM - Outlet Size in Inch : 4.0" & 5.0" - Degree of Protection : IP 58 - Minimum Cooling Flow Along the Motor : 0.15 m/sec. - Type of Duty : S1 (Continuous) - Method of Starting : Star Delta (SD) - Maximum Starts Per Hour : 20 Times Characteristics Of Clear Cold Water - Maximum liquid temperature : 33C max - Permissible amount of sand : 25 g/m - Allowable solids : 3000 ppm (max.) - Chloride ion density : 500 ppm (max.) - Turbidity : 50 ppm silica scale (max.) - Hardness (Drinking Water) : 300 ppm (max.) - Specific gravity : 1.004 (max.) 6 - Viscosity : 6 1.75 x 10 m/sec (max.) - Ph Value : 6.5 to 8.5
V7 Borewell Submersible Pumpset Falcon Premium 175 mm (7) Borewell Submersible pumpsets are powered by water filled, rewindable submersible motor suitable for continuous duty. The stator is wound with special water proof synthetic film insulated copper winding wires and made up of low watt loss silicon steel laminations assembled under pressure and rigidly locked in stainless steel stator shell. Pump Liquids - Clean - Thin - Non-Aggressive - Non-Explosive - Clear - Cold - Fresh water - Without abrasives - Solid particles. Salient Features - Cast iron casting bowl and SS-410 grade impeller in mix flow series - Specially designed high performance thrust bearing (SS-420 Tilting Pad with Carbon plate) to with stand axial thrust loads. - Specially designed Deep Drawn type pump ensures perfect alignment and Thereby increases the life of the pump set - Dynamically balanced rotating parts ensures minimum vibration and longer life - Motor portion covered with corrosive resistance Stainless steel J4 shell - More durability and hygiene - High operating efficiency - Special designed thrust bearing to withstand high axial thrust load - Extremely hardwearing water lubricated bearing - Thread type motor construction ensures services feasibility - Designed for wide voltage operation - Best alternative for JET & Compressor pump set - Additional intermediate bearing in higher stage pumps Specification - Method of Starting : 3 ph -Direct Online (D.O.L) upto 5.5 kW, Star Delta (SD) upto 37.3 kW - Power Range : 11.2 kW to 37.3 kW (15 HP to 50 HP) - Version : Three Phase 350 to 415V, 50Hz AC Supply - Speed : 2880 RPM - Head Range : 18 Mtr. To 650 Mtr. - Discharge Range : 1860 LPM to 55 LPM - Outlet Size in Inch : 2.0 , 2.5 , 3.0 & 4.0 - Degree of Protection : IP 58 - Direction of Rotation : Electrically Reversible -3ph - Thrust Load : 11.2 kW -37.3 kW -8000 lbs - Minimum Cooling Flow Along the Motor : 0.15 m/sec. - Type of Duty : S1 (Continuous) - Maximum Starts Per Hour : 20 Times Characteristics Of Clear Cold Water - Maximum liquid temperature : 33C max - Permissible amount of sand : 25 g/m - Allowable solids : 3000 ppm (max.) - Chloride ion density : 500 ppm (max.) - Turbidity : 50 ppm silica scale (max.) - Hardness (Drinking Water) : 300 ppm (max.) - Specific gravity : 1.004 (max.) 6 - Viscosity : 6 1.75 x 10 m/sec (max.) - Ph Value : 6.5 to 8.5
V9-V10 Borewell Submersible Pumpset Falcon Dlx. 250 mm ( 9 & 10) Borewell Submersible Pumpsets are powered by water filled, rewindable submersibleMotor suitable for continuous duty. The stator is wound with special water proof synthetic film insulated Copper winding wires and made up of low watt loss silicon steel laminations assembled under pressureand rigidly locked in stainless steel stator shell. T-Bolt design in all motor ensures rigid construction. Pump Liquids - Clean - Thin - Non-Aggressive - Non-Explosive - Clear - Cold - Fresh water - Without abrasives - Solid particles Salient Features - SS 304 Grade Investment Casting Bowl and SS-304 Grade Impeller in radial flow MRS series 27Mtr head per stage in radial flow series. - FG 250 Cast Iron Bowl with CED Catted and SS-304 Grade Impeller in Mix flow FMC Series 22Mtr head per stage in Mix flow series. - Specially designed high performance thrust bearing (SS-420 Tilting Pad with Carbon plate) to with stand axial thrust loads. - Specially designed Deep Drawn type pump ensures perfect alignment and Thereby increases the life of the pump set. - Dynamically balanced rotating parts ensures minimum vibration and longer life. - Designed for wide voltage fluctuations. - Motor portion covered with corrosive resistance Stainless steel (SS 304) shell. - More durability and hygiene & High operating efficiency. - Specially designed thrust bearing to withstand high axial thrust load. - Extremely hardwearing water lubricated bearing. - Thread type motor construction ensures service feasibility. - Designed for wide voltage operation. - Best alternative for JET & Compressor pump set. - Additional intermediate bearing in higher stage pumps. Specification - Power Range : 55 kW to 112 kW (75 HP to 150HP) - Version : Three Phase 350 to 415V, 50Hz AC Supply - Speed : 2900 RPM - Head Range : 12 mtr. To 300 mtr. - Discharge Range : 3600 LPM to 960 LPM - Outlet Size in Inch : 4.0" & 5.0" - Degree of Protection : IP 58 - Maximum Starts Per Hour : 10 Times
V5 Borewell Submersible Pumpset Falcon Premium 125 mm (5) Borewell Submersible pump sets are powered by water filled, rewindable submersible motor suitable for continuous duty. The stator is wound with special water proof synthetic film insulated copper winding wires. And, it is made up of low watt loss silicon steel laminations which are assembled under pressure and rigidly locked in stainless steel stators shell. Pump Liquids - Clean - Thin - Non-Aggressive - Non-Explosive - Clear - Cold - Fresh water - Without abrasives - Solid particles. Salient Features - SS 304 Grade Investment Casting Bowl and Impeller in Radial Flow Series.(GRS - Series) - 9 Mtr. Head Per Stage In Radial Flow Series. - Specially designed high performance thrust bearing (SS-420 tilting pad with carbon plate) to withstand axial thrust loads. - Dynamically balanced roating parts ensure minimum vibration and longer life - Motor Portion covered with corrosion resistant S.S. J4 shell - More durability and hygiene - High operating efficiency - Extremely hardwearing water lubricated bearing - Thread type motor construction ensures service feasibility - Specially designed Deep Drawn type pump ensures perfect alignment and Thereby increases the life of the pumpset - Designed for wide voltage operation - Best alternative for JET & Compressor pump set - Additional intermediate bearing in higher stage pumps - Fully SS pumps are available in (GRS - Series) Specification - Power Range : 2.2 kW to 9.3 kW (3 HP to 12.5HP) - Version : Single Phase 180V to 230V, Three Phase 350 to 415V, 50Hz AC Supply (Single Phase available in 3 HP to 5 HP) - Speed : 2880 RPM - Head Range : 12 Mtr. To 640 Mtr. - Discharge Range : 690 LPM to 80 LPM - Outlet Size in Inch : 1.5 , 2.0" & 2.5" - Degree of Protection : IP 58 - Direction of Rotation : Counter clockwise from driving end -1 pH Electrically Reversible -3ph - Thrust Load : 2.2 kW, 4.5 kW- 3500 lbs, 5.5 kW to 9.3 kW -6000 lbs - Flow Along the Motor : 0.15 m/sec. - Type of Duty : S1 (Continuous) - Method of Starting : 1ph-Capacitor Start Capacitor Run (CSCR) up to 2.2 kW, 3ph - Direct Online (D.O.L.) upto 5.5 kW, Star Delta (SD) upto 9.3 kW - Maximum Starts Per Hour : 20 Times Characteristics Of Clear Cold Water - Maximum liquid temperature : 33C max - Permissible amount of sand : 25 g/m - Allowable solids : 3000 ppm (max.) - Chloride ion density : 500 ppm (max.) - Turbidity : 50 ppm silica scale (max.) - Hardness (Drinking Water) : 300 ppm (max.) - Specific gravity : 1.004 (max.) 6 - Viscosity : 6 1.75 x 10 m/sec (max.) - Ph Value : 6.5 to 8.5
Falcon Premium 125 mm (5) Borewell Submersible pump sets are powered by water filled, rewindable submersible motor suitable for continuous duty. The stator is wound with special water proof synthetic film insulated copper winding wires. And, it is made up of low watt loss silicon steel laminations which are assembled under pressure and rigidly locked in stainless steel stators shell Pump Liquids - Clean - Thin - Non-Aggressive - Non-Explosive - Clear - Cold - Fresh water - Without abrasives - Solid particles. Salient Features - SS 304 Grade Investment Casting Bowl and Impeller in Radial Flow Series.(GRS - Series) - 9 Mtr. Head Per Stage In Radial Flow Series. - Specially designed high performance thrust bearing (SS-420 tilting pad with carbon plate) to withstand axial thrust loads. - Dynamically balanced roating parts ensure minimum vibration and longer life - Motor Portion covered with corrosion resistant S.S. J4 shell - More durability and hygiene - High operating efficiency - Extremely hardwearing water lubricated bearing - Thread type motor construction ensures service feasibility - Specially designed Deep Drawn type pump ensures perfect alignment and Thereby increases the life of the pumpset - Designed for wide voltage operation - Best alternative for JET & Compressor pump set - Additional intermediate bearing in higher stage pumps - Fully SS pumps are available in (GRS - Series) Specification - - Power Range : 2.2 kW to 9.3 kW (3 HP to 12.5HP) - Version : Single Phase 180V to 230V, Three Phase 350 to 415V, 50Hz AC Supply (Single Phase available in 3 HP to 5 HP) - Speed : 2880 RPM - Head Range : 12 Mtr. To 640 Mtr. - Discharge Range : 690 LPM to 80 LPM - Outlet Size in Inch : 1.5, 2.0" & 2.5" - Degree of Protection : IP 58 - Direction of Rotation : Counter clockwise from driving end -1 pH Electrically Reversible -3ph - Thrust Load : 2.2 kW â?? 4.5 kW- 3500 lbs, 5.5 kW to 9.3 kW -6000 lbs - Flow Along the Motor : 0.15 m/sec. - Type of Duty : S1 (Continuous) - Method of Starting : 1ph-Capacitor Start Capacitor Run (CSCR) up to 2.2 kW, 3ph - Direct Online (D.O.L.) upto 5.5 kW, Star Delta (SD) upto 9.3 kW - Maximum Starts Per Hour : 20 Times Characteristics Of Clear Cold Water - Maximum liquid temperature : 33C max - Permissible amount of sand : 25 g/m - Allowable solids : 3000 ppm (max.) - Chloride ion density : 500 ppm (max.) - Turbidity : 50 ppm silica scale (max.) - Hardness (Drinking Water) : 300 ppm (max.) - Specific gravity : 1.004 (max.) 6 - Viscosity : 6 1.75 x 10 m²/sec (max.) - Ph Value : 6.5 to 8.5
V6 Borewell Submersible Pumpset Falcon Premium 150 mm (6) Borewell Submersible Pumpsets are powered by water filled, rewindable submersible Motor suitable for continuous duty. The stator is wound with special water proof synthetic film insulated Copper winding wires and made up of low watt loss silicon steel laminations assembled under pressure. Pump Liquids - Clean - Thin - Non-Aggressive - Non-Explosive - Clear - Cold - Fresh water - Without abrasives - Solid particles. Salient Features - SS 304 Grade Investment Casting Bowl and SS-304 Grade Impeller in radial flow series - 60 feet head per stage in radial flow series - Specially designed high performance thrust bearing (SS-420 Tilting Pad with Carbon plate) to with stand axial thrust loads. - Dynamically balanced rotating parts ensures minimum vibration and longer life - Motor portion covered with corrosive resistance Stainless steel J4 shell - More durability and hygiene - High operating efficiency - Extremely hardwearing water lubricated bearing - Specially designed Deep Drawn type pump ensures perfect alignment and Thereby increases the life of the pumpset - Designed for wide voltage operation - Additional intermediate bearing in higher stage pumps - Fully SS pump set are available in SS - 304 Grade Specification - Power Range : 2.2 kW to 30 kW (3.0 HP to 40 HP) - Version : Single Phase 180V to 230V, Three Phase 350 to 415V, 50Hz AC Supply. - Speed : 2900 RPM - Head Range : 12 Mtr. To 600 Mtr. - Discharge Range : 1080 LPM to 170 LPM - Outlet Size in Inch : 2.0, 2.5 , & 3.0 - Degree of Protection : IP 58 - Direction of Rotation : Counter clockwise from driving end -1 pH Electrically Reversible -3ph - Thrust Load : 2.2 kW 4.5 kW - 3500 lbs, 5.5 kW - 30 kW - 6000 lbs - Flow Along the Motor : 0.15 m/sec. - Type of Duty : S1 (Continuous) - Method of Starting : 1ph-Capacitor Start Capacitor Run (CSCR) upto 2.2kW: 3ph -Direct Online (D.O.L) upto 5.5 kW, Star Delta (SD) upto 30 kW - Maximum Starts Per Hour : 20 Times Characteristics Of Clear Cold Water - Maximum liquid temperature : 33C max - Permissible amount of sand : 25 g/m - Allowable solids : 3000 ppm (max.) - Chloride ion density : 500 ppm (max.) - Turbidity : 50 ppm silica scale (max.) - Hardness (Drinking Water) : 300 ppm (max.) - Specific gravity : 1.004 (max.) 6 - Viscosity : 6 1.75 x 10 m/sec (max.) - Ph Value : 6.5 to 8.5
