Primer
Bitumen Primer * Bitumen Primer is Bituminous air curing ready mixed Acid & Alkali resistant special primer. Application * Concrete surface must be clean, dry and rough. No primer should be applied over smooth and wet surface. * After cleaning the concrete surface, one coat of Bitumen Primer should be applied with brush and allow to dry thoroughly. * The drying time will depend upon the temperature. * 24 Month at the temperature 30C (+2OC) Packing * Bitumen Primer: 25 Liter Drum Note * Bitumen Primer contains volatile and slightly toxic solvent. Keep away from spark and open flames at working area. * Bitumen premier it is manufactured using bitumen solution which is used for sealing of prime porous and non-porous surface, and also to protect residential and commercial building. * Bitumen Primer is used to protect substrate against corrosive attack, is suggested to apply anti-corrosive primer.It is best for protection against sub-striate against atmospheric corrosion and chemical corrosion. It is a mixed substance made up of organic liquids that are highly sticky, water proof, viscous,acid proof as with all surface coating, good Bitumen Premier is used for long life of the system. it is applied by brush or roller and allowed to dry before any water proofing treatment so to avoid solvent it is used in defects such as cracks, broken mortar joints, etc. are to be repaired prior to Bitumen primer application. Product Details: Grade Standard Technical Grade Physical State - Liquid Usage - Industrial Color - Black Characteristics: Appearance/Color - Pasty liquid/ black Chemical Base - Bituminous rubber emulsion. Density - 1.0 kg/l Curing Speed/ Rate - 3 - 4 hours Tack free after - 5 - 10 hours Cured after - 2 - 4 days (Dependent on ambient Solid Content by - temperature, substrate temperature, Weight - relative Water Content by weight - humidity and thickness of the coating) Bitumen Content - 41% by weight - Thixotropic (The viscosity can be adjusted by - Viscosity adding up to max. 5% of clean water. - Stir well prior use) - For light protection: 1.0 mm min. Coating - For greater protection: ~ 1.5 - 2.0 mm Thickness applied - in two coats. Water Penetration - 48 h, 1 bar: 78.5 cm2: 0 ml under Hydrostatic - 96 h, 4 bar: 78.5 cm2: 33 ml Pressure - Water vapor 6 x 10-7 mg / hmPa Permeability Service - -30 C to 200 C Temperature - Adhesion Concrete - Very good, Timber: Very good, Metal: Moderate Glass: Poor
Tufkote W8568SLM Primer
Epoxy Primer -guard Primer Is 2 Component Paint System For Interior Walls
Texture Primer-special Primer For Texture Coatings And All Weather Exterior Paints
Plastic Primer For Car Bumpers
A vinyl acrylic primer designed for priming masonry surfaces PROPERTIES Colour : Full range- as per shade card Finish : Smooth / Matt Solids(volume): 24 �±2% Specific gravity: 1.40 �± 0.05 Theoretical Coverage 7-8 m2/ltr @ 40 DFT DRYING TIME :AT 25 Touch dry: 2 hours To Recoat: 4 hours
MASONARY PRIMER It is specially formulated to give a very high level of adhesion and deep penetration into the concrete, which also offers a medium level of opacity. PROPERTIES Colour : Full range- as per shade card Finish: Matt Solids (volume) : 36% Specific gravity: 1.45 +/- 0.03 Theoretical Coverage 6-7 m2/ltr @ 40�¯� DFT DRYING TIME : AT 25 Touch Dry: 2 hours To Recoat: 4 hours Vehicle type: PVA copolymer
>=100 Gallons US$ 1.99 Payments:This supplier also supports L/C,T/T,Western Union payments.
WOOD PRIMER Specially formulated alkyd base wood primer for interior and exterior use. May be used under topcoats such as alkyds,oils,or latex paints. PROPERTIES Colour : White -pinkish Solids: 45% Theoretical Coverage 8 - 10 m2/lit DRYING TIME : AT 25 To handle: 2 hours To Recoat: 24 hours Vehicle type: Modified alkyd Specific gravity: 1.40 Flash point: 35C
Weather proof Water resistant Alkaline resistant Excellent filling property
Bitumen Primer Grade
Textile Epoxy Primer
Neo has extensive range of primers based on Epoxy / PU / Synthetic Resins. NEO PRIME GUARD grades are quality Epoxy based primers while NEO SHIELD PRIME grades are PU primers. These are used as a primer. They exhibit excellent adhesion properties and will stick to bare metal, Paints, primers, and fillers. They are used as a anti corrosive / protective primers. Neo offers multiple grades loaded with special additives, pigments for meeting specific requirements.
Odorless, acrylic-based primer, antibacterial, antifungal, penetrates deep into the surface, strengthens the outer layer. Reduces paint consumption, as the ability of the surface to absorb paint decreases. Used for painting and puttying. Per canister 10L
Product Category- Paint & Primers Product Name- Scottseal Description of the product- Acrylic Primer Area of Use (Application)- Interior and exterior walls Category (For Painters, Carpenters, etc.)- Painters USP of the product- 1. High covering ability 2. Reduces the porosity of the surface 3. Good binding property to the surface Area of application- Interior & Exterior
Product Category- Paint & Primers Product Name- Scott WP Description of the product- Interior Primer Area of Use (Application)- Internal walls Category (For Painters, Carpenters, etc.)- Painters USP of the product- Increases the coverage of top coat and decreases the porosity of the surface Area of application- Interior
Product Category- Paint & Primers Product Name- Scott IP Description of the product- Internal primer for acrylic paints Area of Use (Application)- Internal walls Category (For Painters, Carpenters, etc.)- Painters USP of the product- 1. Good brushability 2. High coverage with superior finish Area of application- Interior
WALL PROTECT Exterior Primer is a water-based wall coating suitable for application on exteriors as an undercoat to exterior emulsions. FEATURES :- 1. Excellent opacity and whiteness 2. Improves appearance of top coat 3. Does not chalk and can be applied on adequately cured fresh plaster 4. Does not require curing with water 5. Provides excellent adhesion to top coat emulsions 6. Prevents peeling off of top coat emulsions RECOMMENDED APPLICATION :- It can be used on all types of exterior cement plasters, exterior ceilings, asbestos sheets, concrete and existing painted surfaces. PRODUCT TECHNICAL DATA :- COLOURS : White FINISH : Smooth and Matt COVERAGE : 1 coat: 120-140 sq.ft/LTR (It may vary from the quoted coverage to factor such as method and condition of application and surface roughness) DRYING TIME : Surface drying time â?? 4-5 HOURS GLOSS LEVELS/SHEEN LEVELS : Silky smooth sheen FLASH POINT (IS101/108 Part 1, Sec 9) : Non- flammable SUITABILITY OF THINNER PAINT Use within 24 hrs. SHELF LIFE 18 months from date of manufacture in original tightly closed containers kept away from direct sunlight and excessive heat.
Description Two component metallic zinc rich epoxy high performance primer. Recommended Use :- The zinc pigment in dry film renders excellent protection to steel structure, tanks, bullets, dam gates, pipelines, plant equipments, jetty, etc. in both interior and exterior exposed conditions of fertilizer units, chemical plants, steel plants, cement plants, pulp and paper industries, ports, power plants, petrochemical and pharmaceutical industry, transformer, machines & other heavy duty OEMs. It also provides cathodic protection to steel and gives good resistance to corrosion at local damaged areas. It is useful in heavy-duty protective paint systems. It is recommended not to expose the primed coat alone to chemical and saline atmosphere for a long time. Physical Data COLOUR : Grey FINISH : Matt SOLIDS BY VOLUME : 50 �± 3% THEORETICAL SPREADING RATE : 10 sq.mt / ltr at DFT of 50 �µ FLASH POINT : Base : Above 23�°C Hardener : Above 23�°C DRYING CHARACTERISTICS (at 30�°C & at 65% Relative Humidity) : HARD DRY : Overnight FULL CURE : 7 days SHELF LIFE : BASE : 6 months HARDENER : 6 months Surface Preparation Abrasive blasting to minimum Sa 2 1/2 Standards is recommended with a profile of 35 - 75 microns. The surface should be absolutely dry and salt free before application. The primer should be applied preferably immediately or within 4 hours of blasting. Application Data :- MIXING RATIO : Base : Hardener (As per our recommendations) APPLICATION : By Brush / By Conventional Spray / By Airless Spray THINNER : Epoxy Thinner 190 POT LIFE : 4 hours min at 30�°C RECOMMENDED DFT : 30 50 µ. OVERCOATING INTERVAL : MIN : 8 hours MAX : Infinite COMPATIBILITY : Compatible with Epoxy, PU, Chlorinated Rubber intermediate/finish coat.
