AAK hydraulic valve has a proprietary valve block anti-rust treatment technology. A special coating with a thickness of 0.02 ~ 0.03 mm is plated on the surface of the hydraulic valve block. The coating has excellent adsorption, is not easy to fall off and has a bright appearance. On this point alone, it has crushed most of its peers. After several email communications, Russian customer resolutely placed an order with AAK. Due to the limitation of process, most hydraulic valve factories adopt surface painting or conventional electroplating for the anti-rust treatment of the hydraulic valve block surface. Such anti-rust treatment on the surface of the valve block will cause problems in the routine maintenance or repair of the hydraulic valve in the future. It is mainly reflected in that the valve block is easy to be scratched, causing corrosion and increasing system pollution. Besides, falling paint and other sundries are also easy to enter the valve block channel and bring pollutants directly to the system, resulting in secondary pollution of the system and accidents. The trouble is that it is generally difficult to find the problem of rust prevention on the surface of these valve blocks in the short term. Anatoly, a Russian hydraulic customer, purchased a batch of hydraulic valve blocks in March from a factory. There were no problems in the preliminary test and final inspection. However, he continued to receive feedback from consumers in the last month. After setting up and debugging, the surface of the valve block fell off paint, rusted, and even there is pollution inside the system. According to the statistics of the information received, among the 200 products purchased, there are nearly 100 products in this situation now, and only 100 are still on sale. Anatoly found something wrong and immediately asked to suspend the sales of the remaining products. At the same time, he communicated with suppliers for many times for these inferior products, but the supplier's attitude was very bad and had always been unable to give accurate solutions. Anatoly used to interact with us on the B2B platform. We didn't know the problems of his valve block until we received his email last month. For these problems, we talked about the current hydraulic market in the reply to his email. In order to save costs, many peers use very conventional anti-rust treatment on the valve blocks. There are mainly two processes: Directly paint the valve block surface after assembling the components. During component disassembly, replacement and maintenance, it is very easy to damage the paint around the component. At the same time, the fallen paint and other sundries are also easy to enter the valve block duct and cause system pollution After all the valve blocks are processed, a layer of oxide film plating is carried out. The surface oxide film is relatively thin, which is easy to be scratched, causing corrosion and increasing system pollution.
The intelligently polished hydraulic valve block is 100% burr can not find a second one Last Wednesday, there was a repeat order from for a hydraulic valve block, which was tested in the second half of last year. required that the repeat order quality should be 100% as same as the hydraulic valve block tested samples last year. comes from a hydraulic equipment company in At the beginning of last year, the paper cutter equipment they sold would stop automatically and was complained by customers. It was found that the hydraulic relief valve was stuck on the site, and the after-sales servicer thought that there was a problem with the hydraulic relief valve. After the original hydraulic valve block manufacturer disassembled it, it was found that there were debris at the moving part of the valve spool. At the same time, foreign matters were also found in the hydraulic oil, so it was known that it was caused by the incomplete burr cleaning of the hydraulic valve block. The original hydraulic valve block manufacturer also does not deny it. The burr cleaning of the inner cavity of the oil channel, the cross hole and the blind hole of this hydraulic valve block was indeed less than 100%. As long as the hydraulic oil can be replaced every 3 months, the problem can be solved. was very speechless and had to find a new hydraulic valve block manufacturer, and deliberately required 100% burr free. She contacted more than 10 hydraulic valve block manufacturers, they either gave no reply or could only have a try, but didn't have time to test, and began to worry. noticed the introduction of 100% burr free hydraulic valve block in on Google, so she directly sent us an email. I told her, according to your hydraulic valve block drawing, there are many inner cavities and cross holes in the oil duct, especially the burr cleaning at the blind hole is a difficult problem. The traditional abrasive flow deburring method to remove this hydraulic valve block has hidden dangers. suffered from it 5 years ago, and it was not until we used the new deburring technology that we dared to ensure 100% burr free asked us to make samples as soon as possible. A month later, sent 5 hydraulic valve blocks. 6 months later, us that the paper cutter installed with hydraulic valve block has been working normally. I told her that adopted an intelligent grinding processing system to replace the traditional abrasive flow process. If this hydraulic valve block is deburred with abrasive flow, and the blind hole is easy to form a dead corner. The intelligent grinding and processing system can realize automatic solution. In the grinding process of the hydraulic valve block, with continuous power support and stability, the main shaft of the equipment can swing 360 , which can realize the grinding of any angle and any inclined plane.
AAK uses endoscope C50 to detect the internal burr of the hydraulic valve block, and then sprays the burr remaining in the hydraulic valve block with high-pressure solution, so that there is nowhere for the burr to hide. Nearly 95% of domestic hydraulic valve manufacturers are not equipped with endoscope and ignore 100% removal of the residual burr of the hydraulic valve block. The American customer who has suffered a loss elsewhere chose to order from AAK again. Most domestic hydraulic valve manufacturers use conventional physical methods to deal with the burr of hydraulic valve block, and check whether the burr is cleaned by experience, especially the burr of deep hole or magnetic burr, which can hardly be cleaned. It is common that the defective rate of hydraulic valve block exceeds the standard due to human error. At the beginning of last year, we received an inquiry for hydraulic valve block from Hunter, an American customer. We calculated the price according to his hydraulic valve block drawings. Hunter was not satisfied with our quotation. Because the communication was very pleasant, I wanted to make friends with hunter and gave up my commission to adjust the price. Hunter frankly said that although the new price of AAK hydraulic valve block meets his target price, the prices of other hydraulic valve manufacturers are still cheaper than those of AAK. We can only withdraw from the purchase of hydraulic valve block amicably. If something goes unusual, there will be problems. 2 months later, Hunter came back to us and said that he was very willing to accept our quotation for hydraulic valve block. He informed that there were different degrees of burrs at the internal cross holes of the hydraulic valve block samples proofed by the original hydraulic valve manufacturer. The hydraulic valve block samples were modified 3 times. Each time the cartridge valve was installed and debugged, the valve spool was stuck from time to time. The factory has also conducted commissioning for many times, and has been unable to remove burrs for 100%. He can only give up this hydraulic valve manufacturer and came back to AAK. Burr must be produced in the drilling process of hydraulic valve block, which is very harmful to the hydraulic system. In addition to adopting appropriate treatment process for burr removal, it is also necessary to have relevant auxiliary testing equipment to guarantee the complete 100% removal of burr. Hunter asked us to arrange approval samples of hydraulic valve block immediately. After 15 days, we sent the hydraulic valve block samples. On the 3rd day after Hunter received the samples, he sent an email to inform AAK that the samples passed testing at one time. Hunter admired that AAK can get the hydraulic valve block samples approved at one time that the peer can't get approval at 3 times. At the same time, he also expressed his curiosity about how AAK can accurately remove the burrs?
AAK hydraulic valve block adopts multi edge particle cutting with diamond reamer, the accuracy can reach 0.002mm, and the surface roughness can reach Ra 0.2um, the precision is twice that of other hydraulic valve manufacturers, and there is no iron filings. Because the price of AAK hydraulic valve block is a little higher than that of peers, LIEBHERR excluded AAK from the supplier list. However, 3 months later, LIEBHERR still placed an order for the hydraulic valve block with AAK. This morning, I received an order for hydraulic valve block from Herta from LIEBHERR company in Germany, which was a little unexpected. Because this is the hydraulic valve block that AAK sent sample for 3 months ago. Since the sample was sent, there was no news about the sample. After several follow up emails, the reply was "unqualified". I asked about the reason why the hydraulic valve block was unqualified, but didn't get reply. Now I can't understand why the order comes to us 3 months later. Herta is mainly responsible for the procurement of hydraulic accessories of LIEBHERR. In the first half of this year, his company needed to purchase a batch of high-precision hydraulic valve blocks for hydraulic excavators. At that time, he selected 5 hydraulic valve factories to send samples to test the quality and conduct assembly tests. 3 months later, after comprehensive comparison, their technical team found that the test data of AAK hydraulic valve block was the best among the 5 hydraulic valve manufacturers. I asked Herta curiously why the reply he gave us 3 months ago was "unqualified". He replied that your quotation was unqualified and more expensive than the other 4 hydraulic valve manufacturers, so we judged AAK to be unqualified. After 3 months of testing, the technical team believes that AAK's hydraulic valve block has the highest precision, the strongest durability and the simplest follow-up maintenance. Although the price of AAK is a little higher than that of other suppliers, according to the comparison of various parameters, the hydraulic valve block of AAK can enable LIEBHERR to reduce the cost of subsequent maintenance, so the technical department designated AAK to supply this hydraulic valve block. Herta asked us why some parameters of AAK hydraulic valve block are twice better than those of peers? The high precision of AAK hydraulic valve block mainly comes from the diamond reamer used in AAK machining center, which is a multi edge particle cutting. In the reaming process, the chips are hidden between the diamond particles and thrown out via coolant flushing and high-speed rotation, so that the chip removal in the first step is complete.
Mason, an old customer of hydraulic valves from the United States. In March this year, he was not satisfied with the quotation of one of our hydraulic valve blocks, which was nearly 7% higher than his target price, so he didn't place an order with AAK HYDRAULIC VALVE. Unexpectedly, he sent an email last week asking whether our quotation of hydraulic valve block in March was still valid. We replied that you were our old customer and the price must be valid. Mason also frankly told us that there was a problem with the hydraulic valve blocks he purchased, which made him very headache now. After communication, we learned that there were no problems in the preliminary test and shipment inspection on the hydraulic valve blocks produced by his previous hydraulic valve manufacturer. In the recent month, users had gradually reported that after setting up and debugging, the surface of the hydraulic valve block fell off paint, rusted, and even there was pollution inside the hydraulic system. Nearly 60% of the 300 hydraulic valve blocks purchased had this situation, and only 40% were still on sale. His manager found something wrong and suspended the sale of the remaining products. The hydraulic valve manufacturer believed that this was caused by the improper use of the hydraulic valve block by the user, and was only willing to replenish 10% of goods to solve this problem. His manager asked him to find a qualified hydraulic valve block supplier as soon as possible. Because the use scenario of this hydraulic valve block was special, Mason knew that AAK HYDRAULIC VALVE could solve this problem, but his did not have authority to pay a 7% higher price. He contacted no less than 10 hydraulic valve manufacturers, and only 3 of them replied. They could solve the paint falling and rust spots on the surface of the hydraulic valve block, but the internal pollution could not be 100% avoided because they did not know the user's operation. The remaining hydraulic valve manufacturers did not give any reply at all. Mason was very helpless. He had to bite the bullet and asked his manager for help if the purchasing price could be raised. When his manager learned about the whole purchase process, he asked Mason, why he did not report this situation in March? After the delivery date provided by AAK HYDRAULIC VALVE was agreed by his users, Mason sent us the order for this hydraulic valve block, and asked us to ship as early as possible. At the same time, his manager was curious about how we did it. The anti-rust treatment of AAK hydraulic valve block in the past is the same as that in other factories, which adopts surface painting or conventional electroplating treatment. The pain point of this process is that the hydraulic valve block is easy to be scratched, causing corrosion and increasing system pollution. We understand these potential problems of this process, and our technical team adheres to the new process exploration, so that AAK now has its own unique
AAK adopts the high-pressure solution injection method, weakens the magnetism of the burr with the solution, and then uses the instantaneous impact force of the liquid to not only ensure that the burr of the hydraulic valve block is 100% eradicated, but also effectively clean each part of the hydraulic valve block. Most of its peers do not have such a process. After learning about it, the American customer sent an inquiry sheet for the hydraulic valve block worth US$20,000 within 20 minutes. Throughout the entire hydraulic valve industry, the deburring of hydraulic valve block is still manual. The work piece is polished with tools such as file, sandpaper and grinding head. This method has blind spots, general effect and low efficiency, especially for the burrs in complex cross holes. Even the later inspection can not find the burr hidden in the hydraulic valve block. Eric, an American hydraulic valve customer, purchased a batch of hydraulic valve blocks from a hydraulic valve manufacturer some time ago. Problems were found in the test stage. The pressure regulation of the hydraulic system was unbalanced. After careful analysis, it was found that there were different degrees of burrs at the cross holes of the hydraulic valve blocks. After modifying the hydraulic valve block sample several times, the burr could not be 100% eradicated. His client did not accept the quality of the hydraulic valve block, and Eric could only reconsider other manufacturers. Eric saw an article on deburring treatment of hydraulic valve block of AAK hydraulic valve on B2B website and found that it was similar to his current problems. Eric sent us his hydraulic valve block drawing and the problems encountered by email. He asked us how to deal with the burr problem of hydraulic valve block? The burr shape and size of the hydraulic valve block are related to the spindle speed, drilling feed, work piece material, cutting tool, coolant, bit geometric angle and other factors. It really needs unique skills to clean it thoroughly. AAK hydraulic valve mainly adopts the high-pressure solution injection method, uses the solution to weaken the magnetism of the burr, and then uses the instantaneous impact force of the liquid to not only ensure that the burr of the hydraulic valve block is 100% eradicated, but also effectively clean each part of the hydraulic valve block, with high efficiency and no dead corner. Within 20 minutes after Eric received our email reply, he sent an inquiry for the hydraulic valve block worth US$20,000. According to his hydraulic valve block drawings and parameter requirements, we calculated the most advantageous hydraulic valve block price. For a week, we didn't hear any news from Eric. We thought he wouldn't order the hydraulic valve block. But we didn't expect that after 15 days, we received his order for the hydraulic valve block. Purchase burr free hydraulic valve block, choose AAK hydraulic valve, you can have a try.
The hydraulic valve blocks designed and produced by not only has high reliability and small pressure loss to ensure that there is no oil running between the channels, but also has compact structure, small occupied space, simple oil circuit and easy pipe layout, so as to ensure the high efficiency requirements of different actions of various actuator elements. The valve block can control the valve, which is easy to adjust and operate. hydraulic valve block was designed and proofed successfully at one time within 1 month, which impressed the engineers o The vast majority of hydraulic valve block manufacturers blindly proofed according to customer drawings, ignored working conditions, and did not understand the internal structure and working principle of hydraulic valve block. It is easy to cause hidden dangers in the hydraulic system, and the problem cannot be found. power insensitivity of the hydraulic system related to the hydraulic valve block We replied that this is difficult to judge because it is a system problem that needs to be checked one by one. the next day then we understood why he left such The power unit of a hydraulic system developed by his company needs a hydraulic valve block. Their engineers mentioned that the sensitivity of the power unit is the key and that all components need to cooperate closely. the hydraulic valve block manufacturer strictly controlled the accuracy according to the drawings, it could be easily done. After the hydraulic valve block is finished, it is installed to test the hydraulic power unit. After the oil pump is started, the instantaneous pressure supply at the oil outlet of the power unit does not come up, and it just supply normal pressure after a few minutes. After checking each component one by one, it is suspected that there are hidden dangers in the hydraulic valve block. After detecting the hydraulic valve block, there is no problem in the oil passage and channel of the hydraulic valve block the original hydraulic valve block manufacturer for analysis and solution. The manufacturer said that the hydraulic valve block was completely produced in accordance with the drawings and the accuracy was within the required range, and the reason for problem was unknown. hydraulic valve block , they all said that they could match the drawings, but not sure about the problems of the hydraulic valve blocks. hydraulic system and the picture of the oil circuit running direction of the hydraulic valve blocks of the original have ideas after 3 aspects of comparative analysis.
The original manufacturer was unable to meet the valve hole requirement for the hydraulic valve block, and Caltha returned to AAK 2 months later Caltha is from Mexico and has been purchasing hydraulic valve blocks in Ningbo China for 5 years. AAK is also one of his suppliers of hydraulic valve blocks. At the beginning of this year, their old buyer left the company and Caltha began to be responsible for the procurement of hydraulic valve blocks. The first inquiry I received from Caltha was for hydraulic valve blocks. A week later, Caltha informed AAK that the price was 17% higher and she chose another hydraulic valve block manufacturer in China. Upon seeing this big price difference, I had to give up. 2 months later, Caltha emailed me asking if the hydraulic valve blocks quoted at the beginning of the year could be completed for 5 samples within 25 days. I felt Caltha's anxiety, and after communication, I learned that the hole accuracy of the hydraulic valve block produced by the original manufacturer was not up to standard. However, the manufacturer blamed some valve hole accuracy deviations on being normal, and using electric sealant could solve the leakage. Caltha didn't want to take any risks and came back to AAK I can understand Caltha's emotions, after all, their company is a loyal customer of AAK. Our technical team started to decompose the hydraulic valve block drawings immediately. Within 25 days, AAK sent 5 hydraulic valve block samples. 2 weeks later, Caltha informed AAK that their hydraulic manifold had been tested successfully. She asked me to wait for the batch order of hydraulic valve blocks. The processing of hydraulic valve block valve holes that the original manufacturer cannot handle mainly depends on the selection of equipment and the control of accuracy. The processing of this AAK hydraulic valve block adopts the Taikan Group Processing Center, which has 3 major advantages: 1. The machining is stable, and its spindle structure adopts high-quality mihanna cast iron, with stable movement. For the same batch of hydraulic valve blocks, using the same tool and processing program, the motion trajectory of the tool is the same, and its CNC program achieves computer control, which can avoid human error. Most hydraulic valve block manufacturers do not choose this equipment. 2. High precision. The valve hole accuracy is within 0.005mm, and the repeated positioning accuracy can reach 0.003mm, and precision correction and compensation can be carried out simultaneously using CNC software. 3. High production efficiency. The spindle speed can reach 24000 RPM, and it also has functions such as automatic speed change, automatic tool change, and other auxiliary operation automation. Compared to ordinary machine tools, the production efficiency is 3-4 times higher. AAK hydraulic valve block, fast processing, and guaranteed accuracy, you can also give it a try!
Zero from Italy often purchases hydraulic valve blocks. In previous years, his customer gave 95 days for delivery date. Some time ago, the customer had an urgent order for 1,200pcs of hydraulic valve blocks, and there was only 60 days from the sample of hydraulic valve blocks to delivery. For non-standard hydraulic valve blocks, the lead time is less than 30 days from drawing design, sample, service life test, production and delivery. Zero consulted all hydraulic valve block manufacturers in cooperation. They all said that it would take 60 days to complete the urgent order of 1,200 hydraulic valve blocks only for production, and the lead time in 90 days is necessary. Zero can't refuse the customer directly, so he has to find a new manufacturer of hydraulic valve blocks. Zero also understands that it is not easy to find a reliable manufacturer of hydraulic valve blocks. Moreover, this is an urgent order, and the processing of hydraulic valve blocks is also complex. There was no reply from all the manufacturers he contacted on the Internet. Occasionally, he mentioned this urgent order of hydraulic valve blocks with his friend Caled. Caled introduced him to try AAK hydraulic valves. Caled is a customer that I have worked with for several years on integrated valve blocks. Caled told Zero that AAK helped him solve several urgent orders for manifolds, and the quality was guaranteed. Zero said frankly that he was introduced by Caled and hoped to get our help. According to the drawing sent by zero, the hydraulic valve block has long and thin channels and complex oil circuit design, which is unbearable for general processing. AAK technical team first arranged the production procedure and calculated the daily output of hydraulic valve blocks. It would take 30 days to complete this urgent order. While Zero was pleased, he seemed a little worried about the quality of AAK hydraulic valve blocks. Three weeks later, their engineers tested AAK hydraulic valve block samples. The overall accuracy parameter of the hydraulic valve block is 5% higher than that of the original manufacturer, which proves what Caled has mentioned that AAK quality mentioned is guaranteed. After working overtime for 30 days, AAK successfully completed the urgent order of 1,200 hydraulic valve blocks for Zero, which is half less than the 60 days of lead time required by peers. Zero was surprised how AAK achieved it? AAK adopts the machining center of compound tools to combine two or more similar or different types of hole machining tools into one special tool. In the process of machining, reduce the tools required for machining X, Y, V and U partial views, and complete the process combination of multiple processes such as drilling, reaming, spot facing and boring. At the same time, one tool can simultaneously process threaded bottom holes, 45 , 15 , R0.1 chamfer and outer counter bore, which greatly
AAK uses the DMG five axis machining center imported from Germany, which improves the stability and accuracy by 30%. Less than 5% of the hydraulic valve block manufacturers in the domestic industry are equipped with this set of equipment. After suffering losses elsewhere, an American customer went back to AAK after 45 days to place the order for hydraulic valve blocks. Last December, I received an inquiry from American customer Joshua about a hydraulic valve block. At that time, I was a little surprised to see the accuracy requirements of the hydraulic valve block. The accuracy was 5% higher than that of HydraForce series. This was not a small challenge, but I was still confident. The next day, I sent quotation to Joshua directly. Joshua then said that it was 12% higher compared with other hydraulic valve block manufacturers, he could not place an order with AAK. After 45 days, Joshua asked us whether the last quotation of hydraulic valve block was still valid. If the original price is maintained, he will place the order for the hydraulic valve block. For the sincerity of cooperation, Joshua also frankly told why he moved the hydraulic valve block order to AAK. The original hydraulic valve block manufacturer made samples for two times, and the parameters of each hydraulic valve block were not very stable. Some hydraulic valve block sample had very good accuracy, while others were very poor, which wasted 3 weeks of time. Joshua also checked with other manufacturers. All of them are not confident to achieve the accuracy that is 5% higher than that of HydraForce series. Another 2 weeks were wasted again. The customer was very angry that the order has been placed for 5 weeks, but the sample of the hydraulic valve block still could not be approved. Joshua felt that only AAK can make the sample successfully at one time. Even if it is 12% more expensive, it is acceptable. Aware of Joshua's dilemma, we specially spare a high-precision DMG five axis machining center lathe to arrange the proofing of this hydraulic valve block. A week later, AAK sent the hydraulic valve block samples. After 10 days, there was still no feedback from Joshua about the hydraulic valve block samples. We asked Joshua to know that he was also waiting nervously. Until Joshua's email last week, we know that his customer was very surprised that the accuracy of this hydraulic valve block sample not only exceeded 5% that of the HydraForce series, but the parameter stability of AAK hydraulic valve block was also more than 30% higher than that last time. Frankly, we were not surprised by this data, because more than one customer was surprised by the accuracy parameters of AAK hydraulic valve blocks. The reason why the accuracy of AAK hydraulic valve block exceeds 5% of HydraForce series is that it firstly benefits from the continuous updating of the equipment. When the vast majority of hydraulic valve block
AAK hydraulic valve blocks adopt MB Series Plug of KVT company in Switzerland, and forms a solid sealing surface after metal extrusion in the way of expansion bite, 100% avoiding oil seepage and oil leakage of hydraulic valve block, which fundamentally solves the problem of high-pressure plugging of hydraulic valve block, and the rated pressure can be as high as 450bar without pollution. Most hydraulic valve manufacturers fail to seal the hydraulic valve block in place, but AAK has become a long-term cooperative supplier of hydraulic valve block for American customer. The vast majority of hydraulic valve manufacturers use the traditional sealing method of inner hexagonal (or outer hexagonal) screw plug and sealing combination gasket to process the hydraulic valve block. The service pressure is basically in the range of 50-300bar, and the operation is simple and easy to disassemble. The hidden danger is that there are requirements for tightening torque. If the torque is not reached, it is easy to leak, and if it exceeds, the thread is easy to be damaged, some hydraulic valve manufacturers even apply anaerobic glue on the thread, which is easy to cause particles of anaerobic glue to fall into the hole, resulting in oil pollution or valve jamming of the hydraulic valve. In addition to the function of hydraulic logic control, some hydraulic valve blocks also need to work for a long time in the environment of high-pressure, high-frequency pressure impact and temperature impact. Therefore, the sealing process of hydraulic valve blocks is very important. Declan, an American customer, is a hydraulic friend of Blake. He recently encountered trouble in purchasing the hydraulic valve block. The approval sample of the hydraulic valve block provided by the original factory showed that the parameters were completely normal in the first test, and there was slight oil seepage in the second test. Declan thought it was something wrong with the hydraulic system. Declan checked and tested the samples for the third time, the hydraulic valve block began to leak oil. After communicated with the original manufacturer, Declan was advised that this sealing process is common in the industry, he should either accept the hydraulic valve block as is or cancel the order. Declan consulted more than 30 hydraulic valve manufacturers through B2B, Google and other websites. Their hydraulic valve blocks all adopt the general sealing process in the industry, and can not guarantee 100% sealing. After consulting Blake, Blake suggested him contacting AAK and told him that AAK hydraulic valves are not market goods and have some their own R & D processes. Perhaps AAK does not adopt the general sealing process in the industry for the sealing of hydraulic valve blocks. According to the hydraulic valve block drawings from Declan, we sent out the hydraulic valve block samples a week later.
Maarten purchased a batch of hydraulic valve blocks some time ago. In the early test, the system parameters were normal. Strangely, 10 days after the hydraulic valve block was started, the hydraulic oil in the system suddenly deteriorated. The technician immediately suspended the operation of the whole test system. After inspection, it was found that there were small iron filings in the hydraulic oil, and the valve spool of the cartridge valve connected with the hydraulic valve block also showed signs of wear. Maarten mentioned these problems to the hydraulic valve manufacturer, but the hydraulic manufacturer asked the customer to use better hydraulic oil and avoided the problem of his own hydraulic valve block. With delivery date approaching, Maarten is very helpless. Maarten really had no choice but to try to find other suitable hydraulic valve manufacturers on the website to take over the hydraulic valve block order. He consulted no less than 10 manufacturers in a week, but all manufacturers gave the same reply, they could not 100% avoid fine iron filings. This made Maarten start to doubt the ability of the hydraulic valve manufacturers in China. Before, Maarten had a certain understanding about us AAK hydraulic valve through some B2B websites, so with a try mentality, he directly emailed us a trial order for 5 hydraulic valve blocks. After receiving our hydraulic valve blocks, Maarten tested and compared, he found that AAK hydraulic valve block has strong sealing, high precision and gloss finish. What's more, he was glad that there was no iron filings residue. He immediately sent the drawings, quantity, delivery date and other detailed requirements of the hydraulic valve blocks currently being purchased from the other hydraulic valve manufacturer. After confirming all details with us, he cancelled the order with the original hydraulic valve manufacturer. At this moment, Maarten could finally rest assured. Why do more than 10 hydraulic valve manufacturers dare not accept the order of this hydraulic valve block? Because this hydraulic valve block is very special. There are many slender holes in the processing channels intersected by each hydraulic valve block, and the cleaning of iron filings is a cumbersome process. If there is no unique skill, it is difficult to eradicate it 100%. 2 years ago, AAK hydraulic valve also had an order cancelled by customer due to the iron filings of hydraulic valve block not completely eradicated. After that lesson, our technical team spent half a year innovating the production process of hydraulic valve block, and finally AAK hydraulic valve was able to mass produce the hydraulic valve without iron filings 1 year ago.
Andrew is the purchasing director of VIS Hydraulics in Italy and an old friend of AAK. He has cooperated with AAK for more than 4 years. One morning in October, I received an email from Andrew with the subject of "a big trouble". It is the first time that I received such an emotional email from Andrew. After reading, it turned out that the pressure of a hydraulic power system of their company was not enough, and the customer complained. The root of the problem is that the hydraulic threaded cartridge valve and hydraulic valve block does not match each other. The owner asked him to solve the problem within a month. After communication, it was learned that the hydraulic threaded cartridge valve and the hydraulic valve block purchased by Andrew were not produced by the same manufacturer. Now both manufacturers do not admit that it was their own problem. The hydraulic threaded cartridge valve manufacturer said that the pressure of the hydraulic system was slow due to the processing accuracy of the hydraulic valve block, while the hydraulic valve block manufacturer said that the hydraulic threaded cartridge valve had leakage, resulting in insufficient flow. Andrew failed to communicate for several times and thought of AAK. During so many years of cooperation, only AAK hydraulic valve has no complaint. He hopes that AAK can help him find out what the problem is. Andrew sent us the design drawings of the hydraulic threaded cartridge valve and hydraulic valve block. After analysis, AAK engineers found that the probability is that the design of the hydraulic valve block is unreasonable, the flow area of the through hole designed is not enough, and the direction and position of the oil inlet and outlet are not optimal, resulting in insufficient pressure of the whole hydraulic system. Andrew asked the hydraulic valve block manufacturer to design and produce, but the manufacturer needs 2 months to complete it, while the time given by his owner is only 1 month. Andrew asked the fastest time that AAK can finish the hydraulic valve block. Our engineers are worried that there may be deviation if design the hydraulic valve block alone. If combined with the mapping of the valve, we can achieve 100% of the optimal design scheme. We recommended Andrew to send us the hydraulic threaded cartridge valve, too. After receiving it, the scanning analysis was carried out, and the design scheme was obtained 2 days later. After 20 days, the redesigned hydraulic valve block was sent to Andrew. After installation and commissioning, the pressure of the hydraulic system was normal. After the complaint was resolved, the owner was also happy and asked Andrew to purchase both the hydraulic threaded cartridge valve and hydraulic valve block from AAK in the future. Don't purchase them separately any more. AAK engineers use professional automation studio version 7.0 software to automatically generate simulated hydraulic valve block of
Hydraulic valve blocks with no deviation in valve hole accuracy, AAK replaced Russian manufacturer Sumarokov comes from Russia and has been engaged in the procurement of hydraulic valve blocks for 7 years. His boss also thinks highly of him. At the beginning of the year, Sumarokov needed to purchase a hydraulic valve block for use in a hydraulic tractor. He took samples from local hydraulic valve block manufacturers, and the test run was smooth. But he didn't expect that 1 month after the sale of the hydraulic tractors, some customers complained that the equipment was unstable and there was leakage at the hydraulic valve block aperture, but the original hydraulic valve block manufacturer thought that it had nothing to do with their hydraulic valve blocks. There were more and more complaints from customers, but the original manufacturer did not cooperate, and Sumarokov had a big headache. On B2B, Sumarokov saw many articles about hydraulic valve blocks from AAK and left us a message: can you ensure that every valve hole of hydraulic valve blocks is processed without deviation? I guessed that the machining accuracy of the holes of the hydraulic valve blocks he purchased was uneven. After communication, I learned that he was in trouble. I told him that most hydraulic valve block manufacturers use 5 processes of drilling, reaming, spot facing, reaming and grinding to process the valve holes. The hidden trouble is that in the process of hole reaming and grinding, the expansion of the orifice is not easy to control, and the aperture may not be absolutely consistent. I suggested Sumarokov directly trying AAK samples of the hydraulic valve blocks. Whether AAK can do it well or not, it does not depend by mouth. You can tell by the samples directly. Sumarokov accepted my proposal and paid for the development cost. After 25 days, 40 hydraulic valve blocks were sent out to solve the customer's complaint first. Last week, Sumarokov said in an email that it has been 3 months since AAK hydraulic valve block was installed on the hydraulic tractor, and there is no complaint of leakage. The hydraulic valve block looks simple, but in the processing of valve holes, the processing technology needs to be determined according to different accuracy requirements, not simple drilling, reaming, spot facing, reaming and grinding. AAK is different and lead most hydraulic valve block manufacturers with 3 points. 1. Choose the reamer. For the processing of the valve hole of this hydraulic valve block, we use the reamer made of 50W6MO5G4V2A1 material with hardness of HRC66 instead of the conventional W18Cr4V. 2. In terms of equipment, we use a high-precision machining center imported from Switzerland. The roughness of the processed hydraulic valve block valve hole can reach Ra value of 0.8-0.4�¼m. The ovality circle error and taper error can be controlled within 0.01-0.02mm, and the valve hole size accuracy can be controlled within 0.01mm.
AAK hydraulic valve, adopts URMA reaming technology of Swiss quality to process the valve spool hole in the hydraulic valve block. With the precision, reliable and efficient URMA reaming technology, the high precision of the valve spool hole of the hydraulic valve block is ensured, and the stable surface quality and tolerance range are maintained in the whole hole diameter. Brody, an American customer, had asked about no less than 20 hydraulic valve manufacturers, but no hydraulic valve block manufacturer had the ability to undertake his order for hydraulic valve blocks with special valve spool holes. After 3 days of communication with AAK hydraulic valve, he directly placed a trial order for 200 hydraulic valve blocks. The valve spool hole is the key point in the hydraulic valve block. Many hydraulic valve block manufacturers do not have their own high precision equipment, so they can only process outside. Generally, the outside processing centers only process according to the process parameters, and rarely consider the properties, use scenarios, and service life of machining components. It is difficult to continuously and stably grasp the diameter dimensional tolerance of valve spool hole, coaxiality, cylindricity and roughness. Once such a hydraulic valve block is used, it will directly affect the quality and operation stability of the whole hydraulic system. Brody, who needed to purchase a batch of special hydraulic valve blocks, asked no less than 20 hydraulic manufacturers, but no manufacturer was able to undertake this order. Brody browsed our website, www.aakindustry.com, emailed us, listed us the process parameters of the valve spool hole in the hydraulic valve block, and the internal anatomy diagram, and asked if we could do it? This hydraulic valve block had high precision requirements due to the existence of most segmented structures in the valve spool hole, small diameter dimensional tolerance of the valve spool hole, and many precision requirements such as coaxiality. This processing was very difficult. I was also curious why Brody didn't ask us like other customers what tools we used. Brody said he didn't need a tool for machining holes, but holes. When Brody learned that we AAK hydraulic valve could meet the process requirements of his hydraulic valve block and was willing to make a sample for him to test, he seemed to feel that perhaps only AAK hydraulic valve could help him solve the problem of this hydraulic valve block. When he received our hydraulic valve block samples, he informed us by email on the 3rd day that the test results of hydraulic valve block met the requirements. He was also curious about how we AAK hydraulic valve achieved it. AAK hydraulic valve, adopts URMA reaming technology of Swiss quality to process the valve spool hole in the hydraulic valve block.
3 pressure test standards of hydraulic valve block replaced 1 pressure test standard of , no longer worries about losing customers is one of our old customers of hydraulic valves in . He purchases hydraulic cartridge valves from all year round. Recently, he suddenly asked me some technical parameters of hydraulic valve blocks. I was a little surprised. After further communication, I learned that he started to purchase hydraulic valve blocks for the first time last year, but failed. purchased a batch of hydraulic valve blocks from a manufacturer who just produced hydraulic valves for him in the past. Maybe this manufacturer didn't know enough about the hydraulic valve blocks. After 100 hydraulic valve blocks arrived, there was a problem after sales. According to the user's feedback, the pressure of the hydraulic valve blocks could not meet the system requirements, and the pressure was also unstable. Most hydraulic valve blocks were required to be returned. The manufacturer also said that these hydraulic valve blocks had been tested before leaving the factory. Now these hydraulic valve blocks are stacked in the warehouse. regretted it so much that he was sad all day long. According to the hydraulic valve block drawings, sample photos, and videos provided by , I told him that the processing accuracy of the hydraulic valve block should still be flawed. Although the original manufacturer also did the pressure test, he may not understand that there are 3 types of hydraulic valve block pressure tests, or even he just completed the pressure test on the pressure test bench. This is a common problem in pressure test of most hydraulic valve block manufacturers, but never tests pressure like this. 2 weeks later, I sent 10 samples of hydraulic valve blocks according to his drawings. About 2 weeks later, Andy advised that when hydraulic valve block was installed, the pressure parameters were consistent with the system requirements, and it was smoother and had more stable pressure debugging than that of the original manufacturer. Users liked it very much. disposed of the hydraulic valve blocks in the warehouse and asked us to replenish 100 pieces as soon as possible to fill the inventory. I told that the processing of hydraulic valve blocks will not be falsified in terms of accuracy first and finally in the pressure test stage of hydraulic valve blocks will not be sloppy. The pressure test is carried out directly in the hydraulic system, which is more consistent with the operating conditions than the test on the pressure test bench. At the same time, the test pressure is determined according to the working pressure of the system. However, most manufacturers cannot directly test the hydraulic valve block in the hydraulic system, and directly use the traditional process to test on the pressure test bench.
AAK hydraulic valve blocks are processed with compound cutting tools, and the production efficiency is nearly 50% higher than that of peers. At the same time, the precision of hydraulic valve blocks is also improved by 5%. AAK completed the urgent order of 1,000 hydraulic valve blocks in only 30 days, while most hydraulic valve block manufacturers can't control the processing technology of compound cutting tools. German customers are also attracted by it. It's a little strange that since the second half of last year, many inquiries about hydraulic valve blocks have an urgent delivery date. They need to be shipped within 20 days or finished within 30 days. For non-standard hydraulic valve blocks, from production drawing design, sample, life test, production to delivery, the vast majority of hydraulic valve block manufacturers need 45-60 days. But this is desperate for the customers with urgent order of hydraulic valve blocks, and Bach in Germany is one of them. Bach wanted to purchase 1,000 pcs of hydraulic valve blocks a few weeks ago. His customer requested that the goods be delivered to Germany in 50-60 days, but the quotation of the local factory in Germany exceeded his budget. He could only find the manufacturer of hydraulic valve blocks in Ningbo, that is, goods need to be shipped in 30 days. Bach contacted nearly 20 hydraulic valve block manufacturers, but none of them can complete the production of 1,000 hydraulic valve blocks in 30 days. A few days ago, we received Bach's message on AAK website (www.aakindustry.com): I saw an article on B2B that "AAK processes hydraulic valve blocks with compound cutting tools, and the delivery time is 30 days faster than peers". Can AAK complete non-standard hydraulic valve blocks in 30 days? After communication, I learned that Bach was troubled by the delivery date of hydraulic valve blocks. I directly told him that the 30 days of lead time for 1,000pcs of hydraulic valve blocks is enough for AAK. AAK adopts the compound cutting tool processing technology that most hydraulic valve block manufacturers can't control, that is, combining two or more similar or different types of hole processing tools into a special composite tool. In the process of machining, reduce the tools required for machining X, Y, V and U partial views, and complete the process combination of multiple processes such as drilling, reaming, spot facing and boring. At the same time, one tool can simultaneously process threaded bottom holes, 45 �°, 15 �°, R0.1 chamfering and external counterbore, which greatly improve the processing efficiency and have the characteristics of high efficiency, high precision and high stability. This is the "trump card" of AAK to improve the production efficiency. The production efficiency is nearly 50% higher than that of its peers. At the same time, the precision of hydraulic valve blocks is also increased by 5%.
Kayden, from AH Garner company in the UK, has successfully purchased hydraulic valve blocks in Ningbo in recent years, and has cooperated with AAK on some high requirements hydraulic valve blocks for many years. He sent an email at the end of last year: I need AAKâ??s help. After communication, we learned that a new hydraulic equipment of their company was complained by customers about oil leakage in about 3 months. After inspection, their after-sales personnel found that when the equipment is switched with high-speed and high-frequency action under high pressure, the small O-ring of the cover plate of the hydraulic valve block is prone to oil leakage. The engineer asked Kayden to find the original supplier to replace the hydraulic valve blocks or cartridge valves. Unfortunately, Kayden purchased the hydraulic valve blocks and threaded cartridge valves from two factories. The manufacturer of the hydraulic valve blocks replied that the thread size accuracy of the cartridge valves did not meet the standard and caused oil leakage, while the cartridge valve manufacturer said that the accuracy of the hydraulic valve blocks did not meet the standard. The hydraulic valve blocks and cartridge valves have passed the inspection. How can there be a problem as soon as they are assembled on the equipment? Kayden suspected that the design of the hydraulic valve block was flawed, but the engineer thought the design drawing was in line with the principle. The customer didn't receive the solution, and complained to the boss, who asked Kayden to completely solve the oil leakage problem of the hydraulic valve blocks within 30 days. Now Kayden was stumped and didn't have a clue. I asked Kayden to send us the drawings of the hydraulic valve block and cartridge valve, and system principles. AAK engineers found no problems after analysis. Our engineer asked Kayden to provide the video after the equipment was started up. Combined with the system schematic diagram and equipment fault video, our engineer judged that the position of installing O-ring at the interface of hydraulic valve block and cartridge valve was inappropriate. If the position of the O-ring is lowered, and the cover plate O-ring is completely free of oil, install and fasten the cartridge valve cover plate, and produce the hydraulic valve block and cartridge valve in a same factory, the oil leakage problem of the hydraulic valve block may be solved completely. Kayden seems to have seen the dawn and asked AAK to make samples. After 25 days, AAK sent out the integrated hydraulic valve block sample. A few days ago, Kayden emailed us that it has been 3 months since the hydraulic valve block was replaced with AAK samples, the equipment works normally without oil leakage. Kayden told me that AH Garner engineer admired AAKâ??s strictness in details. It is so obvious, why didn't he find such an obvious problem?
William comes from a Canadian hydraulic equipment company and has purchased hydraulic valve blocks in Ningbo for several years. AAK also supplies several difficult hydraulic valve blocks to their company. Although the quantity is not big, AAK service makes William very satisfied. In the second half of last year, William emailed an inquiry for a big quantity of order for hydraulic valve blocks. William said that the quotation was 40% higher than that of other hydraulic valve block manufacturers. I'm not surprised at all that he advised that the price of AAK hydraulic valve block is 40% higher. According to the hydraulic valve block drawing provided by William, AAK engineers found that according to the working condition requirements of the hydraulic valve block and the minimum wall thickness between two adjacent parallel holes (including installation threaded holes) in the middle of the valve block designed on the hydraulic valve block drawing is less than 4mm, the 6061-T6 Aluminum material marked in the drawing is not suitable, because this wall thickness can not bear the pressure of 350bar at all. During the operation of the equipment, the hydraulic valve block is likely to be broken down because it cannot withstand high pressure, that is, the materials used for the hydraulic valve block must be changed, rather than blindly follow the original hydraulic valve block drawing. AAK uses 7075-T6 aviation aluminum, which is the root cause of 40% higher price. A week later, William replied that he also sent the inquiry to the old hydraulic valve block supplier and more than 10 other hydraulic valve block manufacturers, but none of them suggested change the aluminum materials. He wondered whether AAK deliberately changed the materials for more profits. This large order of hydraulic valve blocks had been placed with the original supplier. Then I replied with a few words: good luck. Two months later, William sent an email saying that he regretted that he had not followed AAK suggestion at the beginning. The hydraulic valve block sample from old supplier was debugged 3 days after the equipment was installed. The manufacturer of the hydraulic valve blocks said that the sample was completely in accordance with the drawing and the development cost could not be refunded. The equipment commissioning time was wasted. The boss was very unhappy and asked William to try AAK samples even if the price was 40% higher, and asked to send the hydraulic valve block samples as soon as possible. AAK uses 7075-T6 aviation aluminum to make samples by soonest. After 30 days, AAK sent 2 samples of hydraulic valve blocks. Last Monday, when I opened the mailbox, I saw the unread email of hydraulic valve blocks from William. I knew that AAK hydraulic valve blocks passed the test of equipment commissioning. After opening, as expected, he placed a large order of 800 hydraulic valve blocks at one time. He also felt sorry to mistake AAK professional suggestion for deception.
Mathias, a Dutch hydraulic customer, urgently needed to purchase a batch of hydraulic valve blocks matching the German brand from China at the end of last year. He asked more than 10 old hydraulic valve block manufacturers. They all said that the accuracy of this hydraulic valve block was too high for their technology and equipment. Mathias had a hunch that nine times out of ten, the order for this hydraulic valve block would fail, because he knew that most hydraulic valve manufacturers just have CNC machine tools. But his owner attached great importance to this customer and asked him to implement the hydraulic valve block sample within 30 days. Within a week, Mathias consulted nearly 20 hydraulic valve block factories online and offline, almost all of them just have CNC lathes. Only two of them said that they have Japanese high-precision CNC machine tools. They can try to make samples but are not 100% sure. Two weeks later, Mathias tested the hydraulic valve block samples from 2 factories, and there was still a parameter error of 10% - 13%. Mathias suggested the factory re-make samples, and both factories surrendered. Time has been wasted for 3 weeks. It's only 2 weeks from the deadline required by the owner. Mathias is anxious and has no direction. While chatting with old friend Andy, Mathias revealed his dilemma. Andy is a veteran in the hydraulic valve industry and has cooperated with AAK hydraulic valve for 5 consecutive years. Andy told Mathias that the accuracy of this hydraulic valve block requires not only high-precision machine tools, but also old operators who understand the equipment. Most hydraulic valve block manufacturers are difficult to meet these two requirements at the same time. He suggested Mathias try AAK, who likes to overtime difficulties on high-precision hydraulic valves, and most operators have more than 5 years of experience in operating imported equipment. The subject of Mathias's first email to AAK hydraulic valve was that I was introduced by Andy. He said that the accuracy of this hydraulic valve block can only be produced in AAK. Opening his hydraulic valve block drawing, AAK engineers have 90% confidence. I replied to him directly that if it goes well, we can send the hydraulic valve block samples before the Chinese New Year holiday. Jan 28th is our last working day before CNY and the last day to send samples. Our team was great to send the samples on Jan 28th. When we came back from the Spring Festival holiday, we received an email from Mathias. Their technical team tested the accuracy of AAK hydraulic valve blocks. Each parameter met the accuracy required by the drawing, and almost every parameter was 30% higher than that of other hydraulic valve manufacturers. AAK is also the only hydraulic valve block manufacturer that can match the German brand among all the hydraulic valve manufacturers he contacted. He can finally make a
