It is mainly used for floor intermediate coating and sealing of indoor places with high environmental protection requirements. Each group is divided into two components at the proportion of 20:4, weighing 24kg. It is mainly used for floor intermediate coating and sealing of indoor places with high environmental protection requirements, featuring environmental protection, low VOC content, thinning after adding water, large area application, strong filling performance and easy construction.
Epoxy Finish Paint is two-component, polyamide adduct cured, General Purpose Air drying Epoxy Coating. Its Excellent substitute to Enamel.
Waste Specification: European Classification: E46 EWC Code: 19.01.02 Basel Code: B10 10 The material is loose steel scrap processed through an incinerating plant for domestic waste followed by magnetic separation, fragmentized into pieces and consisting partly of tin coated steel cans. At a visual inspection, the material is fragmentized, with iron and steel parts, resulting partly cut or in shredded form. The stock appears heterogeneous and contains all kind of cut or dismantled steel parts such as sheets, bars, frames, wires, bolts and other iron/steel household residues. The incinerated scrap is eventually oxidized, due to the thermal and cooling treatments, that the material has been submitted to. The burnt scrap also contains minor slag parts, ash and iron oxide, due to the recovery process. Such components are inherent and adhere to the scrap surface. The total impurities, can be sorted, but not fully removed. The consignment does not contain any type of arms, ammunition, mines, shells, cartridges, radioactive contaminated, or any other explosive material in any form either used or otherwise. The collected stock, is stored in open air, on cemented flooring. Due to the scrap dimensions and the material conditions, this particular scrap, should be carefully evaluated first, by the end users, to confirm its adequate recovery ratio and its suitability to be re-melted in the electric arc furnace. Please feel free to contact us for further details
JHG tinted glass is produced by metal oxides to the float glass. The colour may be transferred in the series of blue, green, grey, bronze flexibly. The performance of visible light, privacy and solar heat transmission will be changed arrording the colour change. Different tinted glass offers varied application possibility-from interior partitions, to home appliance, to furniture, to facades and auto field. Reflective glass is float glass with a metallic coating that cuts off solar heat.The coating film may provide mirror effect, preventing visibility from outside and preserving privacy. JHG mainly offer 2 kinds of reflective glass. Hard reflective glass (on line) includes blue, green, grey, bronze, pink, silver colour, Soft reflective glass (off line) includes golden, silver, purple colur. Specification Sizes:1220*1830/1830*2440/1650*2140/2140*3300/2140*3660/2440*3660/2250*3660/3300*4500/5100/6000mm Thickness: 3-12mm Quality standard GB11614-2009/SGCC/EN 572
Each razor with 2 platinum coated blades and plastic cap 5 such razors in a pouch pack 12 such pouch packs in an inner carton 12 such inner cartons in a case i.e., 144 packs or 720 razors in a case 24 such cases on a pallet (pallet size 120 x 100 x 147) by air OR 40 such cases on a pallet (pallet size 120 x 100 x 235) by sea OR 520 such cases without pallets, direct on floor in a 20' dry container OR 1,050 such cases without pallets, direct on floor in a 40' dry container OR 1,260 such cases without pallets, direct on floor in a 40' HC dry container.
Liquid Ethyl Acetate: Ethyl Acetate is an ester of Ethanol and Acetic Acid, (systematically Ethyl Ethanoate, commonly abbreviated EtoAc or EA) an organic compound having formula CH3COOCH2CH3. Liquid Ethyl Acetate is a colorless solvent has a characteristic sweet / fruity smell. We are a distinguished Liquid Ethyl Acetate Exporter based in India. Liquid Ethyl Acetate, offered by us, is perfect in formulation is well-tested. Further, we welcome bulk orders for Liquid Ethyl Acetate with complete sense of responsibility. Applications: - Ethyl Acetate is used in a variety of coating formulations such as epoxies, urethanes, cellulosic, acrylics and vinyl’s. - Applications for these coatings are numerous wood furniture and fixtures, agricultural, construction and mining equipment, auto refinishing, and maintenance and marine uses. - Ethyl Acetate has applications as a solvent in inks for flexographic and rotogravure printing. - It is used as an extraction solvent in the production of pharmaceuticals and food, and as a carrier solvent for herbicides. - High purity product can be used as a viscosity reducer for resins used in photoresist formulations in the electronics industry.
- Material: Natural bamboo 100% - Type: 4 steps, 5 steps,... - Process: Clean, no defects, polished, colored or natural, Coated with gloss paint, fumigated.
COCONUT COIR POT Coconut fiber pot made from coconut fiber products. As good crop products and environmental protection. Coir pots benefits are versatile, more air floating through the plant roots, which will enable the plant in the coconut coat to grow stronger and quicker. All our coir pots are for sale in different sizes and shapes.
Type: Floor Boughpot, Flower Kettle/Sprinkler, Flower Tub, POTS, Pergola, Propagator Kits, Small Fence, VASE, Flower Basket, PLANTER Usage Condition: FLOOR Style: Classic Used With: Artificial Flower Place of Origin: Ho Chi Minh City, Vietnam Material: Natural Bamboo Finishing: Not Coated Usage: Home Garden Decoration
DATA SHEET FOR EPOXY EPOXY COATING :- INTRODUCTION - EPOXY COATING (HYB) is a two part high solids solvent free epoxy phenolic resin based coating system designed for hard wearing, smooth surface finish for floors, walls and on steel structures. Nonskid surface finish can be achieved on floor, if required. FEATURES: 1) Hard Wearing 2) Non Dusting 3) Excellent Surface Finish 4) Non Smelling 5) Good Aesthetics 6) Highly Chemical Resistant APPLICATION: 1.Stir well before mixing Part A and Part B and mix in the prescribed ratio. 2.Apply one coat of EPOXY primer on the clean and dry surface. 3.EPOXY COATING (HYB) should be applied on the surface by brush or roller within 24 hrs. After application of primer coat it should be allowed to air dry for min. 4 hrs. Preferable in a dust free atmosphere. 4.Apply min. 2 coats with the intercoat interval of 6-8 hrs. PRODUCT SPECIFICATIONS: Application - Brush, Roller Mixing Ratio - As Directed on Packing Port Life - 30 Mins. Drying Time - Touch Dry- 30 Min, Hard Dry 6 Hrs. - Intercoat Interval 6-8 Hrs. Min. - Dry Film Thickness 125-150 Microns/per coat - depending on porosity Covering Capacity - 6-8 sq.met/kg per coat depending on porosity, roughness & method of application. Color Shades - All Standard Shades RECOMMENDED USES: 1) Food & Pharmaceutical 2) Work Shop 3) Clean Room Application 4) Chemical Resistant Coating for Concrete& Steel 5) Petrochemical, Fertilizer plants METHOD OF APPLICATION: SURFACE PREPARATION The long-term durability of the applied Epoxy coating (HYB) epoxy coating is dependent on the adhesion between sub-base and coating material. It is most important therefore, that the substrate surfaces are correctly prepared prior to application. 1.Before application of the Epoxy coating (HYB) surface should be free from loose partials, rust, oils, grease or earlier coatings and should be totally dry. 2.New concrete or cementations surface should be placed at least 28 days and have a moisture content of less than 5% before application of Epoxy coating (HYB) 3.After surface is dry, all repair work like sealing of joints, cracks filling of cavities and crevices should be carried out. HEALTH & SAFETY - Keep the containers tightly closed when not in use. Avoid contact with skin & eyes. It comes in contact with the body, wash affected parts with plenty of water and contact a doctor. Other known sector for Epoxy floor lining, Epoxy garage floor lining, Concrete epoxy lining, Concrete floor epoxy lining, Epoxy pipe lining, Marine epoxy lining, Sub marine epoxy lining, Basement lining epoxy floor shield, Louisiana, Oregon, Chip lining color epoxy floor, Aviation lining epoxy interior.
METHOD OF APPICATION: * Mastic compound application consist of two coats of. Primer ,Primer and followed by Mastic compound in recommended thickness, ranging from min. 12mm to 25mm in one or two layers to achieve desired thickness without any pin hole and crack. 1). Surface preparation and application of Primer: Refer application method of Primer. 2). After doing necessary surface preparation and application of primer coating, area to be installed with Mastic compound should be divided in to equal no. bays. To maintain even thickness required, place wooden or aluminum batten. Mastic compound is then broken in small pieces and put it in heating pan. While heating, keep material moving to avoid burning. It is heated until it comes in a uniform consistency and then applied on the surface and works it with wooden float, to achieve uniform thickness and smooth surface free from any pinholes. CHEMICAL RESISTANCE PROPERTIES: * Mastic compound has good resistance to weak, diluted acids, alkalis salts etc. It is not recommended to use against strong acids, oxidizing acid solvents, oil and fats STORAGE & PACKING: * Keep Mastic compound away from direct sunlight, heat solvents etc. Under this condition, its shelf life is unlimited. It is supplied in cake form and approx. wt. is 10 kgs. HEALTH & SAFETY: * Handle melted Mastic compound compound very carefully . Avoid contact with skin. It is advisable to wear protective wears at the time of use of Mastic compound and all other our products. This information, given in good faith, is based on results gained from experience and tests. However, all recommendations or suggestions are made without guarantee since the conditions of use are beyond our control.
temperable mirror is processed by sputtering coating technology craft, without painting in the backing side. temperable mirror can be tempered as float glass to increase the safety factory . temperable mirror is more durable without stainted edge problem caused by backing painting.
JHG offer differnt sizes of tempered glass, annealed glass to meet the inquiry for greenhouse ,hobby garden , Glass thickness is 3mm/3.2mm/4mm/5mm Glass items : clear float glass ,acid etched glass ,diffused glass high haze glass ,AR coated glass Max LT >99% Max haze>50%
JHG is professionally offering all various of high quality laminated glass: 1) PVB laminated glass Colour includes clear/milk/bronze/grey/blue/green/black PVB film thickness is 0.38/0.76/1.14mm or thicker Both standard size and customized sizes available 2)Sentryglass Plus(SGP)laminated glass SGP bring more safe,more transparent for construction ,the film includes 0.89/1.52/2.28mm and thicker mainly used for glass floor,glass step,glass fin,curtain wall Max size is 18000mm length 3)EVA laminated glass It can be laminated with large range of inserts including PET film,polycarbonates,wood veneer,metal,paper ,stones,screeen mesh ,and so on ,it will bring mulrirusinous choice for inner decoration.
SOLAR GLASS JHG solar glass including texture glass and flat glass ,it is the nice performance low iron glass with high solar transmittance, and low reflection . After tempered, it will be the ideal choice for photovoltaics, solar thermal collector ,and greenhouse . Size Maximum Size:1665*2200mm Minimum Size: 300*300mm Specifiction Main thickness 2-5mm Dimension tolerance �?�±1.0mm Thickness tolerance �?�±0.2mm Diagonal tolerance 0.2% Overall bow
Epoxy Floor Coating (interior Floor Coat) Covered/underground Car Park/garage Warehouse Coatings Factory/food Plant Coating Industrial Floor Coating Self Levelling Floor Coat Hygienic Coating (anti-bacterial)
DATA SHEET FOR EPOXY EPOXY COATING :- INTRODUCTION - EPOXY COATING (HYB) is a two part high solids solvent free epoxy phenolic resin based coating system designed for hard wearing, smooth surface finish for floors, walls and on steel structures. Nonskid surface finish can be achieved on floor, if required. FEATURES: 1) Hard Wearing 2) Non Dusting 3) Excellent Surface Finish 4) Non Smelling 5) Good Aesthetics 6) Highly Chemical Resistant APPLICATION: 1.Stir well before mixing Part A and Part B and mix in the prescribed ratio. 2.Apply one coat of EPOXY primer on the clean and dry surface. 3.EPOXY COATING (HYB) should be applied on the surface by brush or roller within 24 hrs. After application of primer coat it should be allowed to air dry for min. 4 hrs. Preferable in a dust free atmosphere. 4.Apply min. 2 coats with the intercoat interval of 6-8 hrs. PRODUCT SPECIFICATIONS: Application - Brush, Roller Mixing Ratio - As Directed on Packing Port Life - 30 Mins. Drying Time - Touch Dry- 30 Min, Hard Dry 6 Hrs. - Intercoat Interval 6-8 Hrs. Min. - Dry Film Thickness 125-150 Microns/per coat - depending on porosity Covering Capacity - 6-8 sq.met/kg per coat depending on porosity, roughness & method of application. Color Shades - All Standard Shades RECOMMENDED USES: 1) Food & Pharmaceutical 2) Work Shop 3) Clean Room Application 4) Chemical Resistant Coating for Concrete& Steel 5) Petrochemical, Fertilizer plants METHOD OF APPLICATION: SURFACE PREPARATION The long-term durability of the applied Epoxy coating (HYB) epoxy coating is dependent on the adhesion between sub-base and coating material. It is most important therefore, that the substrate surfaces are correctly prepared prior to application. 1.Before application of the Epoxy coating (HYB) surface should be free from loose partials, rust, oils, grease or earlier coatings and should be totally dry. 2.New concrete or cementations surface should be placed at least 28 days and have a moisture content of less than 5% before application of Epoxy coating (HYB) 3.After surface is dry, all repair work like sealing of joints, cracks filling of cavities and crevices should be carried out. HEALTH & SAFETY - Keep the containers tightly closed when not in use. Avoid contact with skin & eyes. It comes in contact with the body, wash affected parts with plenty of water and contact a doctor. Other known sector for Epoxy floor lining, Epoxy garage floor lining, Concrete epoxy lining, Concrete floor epoxy lining, Epoxy pipe lining, Marine epoxy lining, Sub marine epoxy lining, Basement lining epoxy floor shield, Louisiana, Oregon, Chip lining color epoxy floor, Aviation lining epoxy interior.
JHG fire-resistant glass is combined with borosilicate glass and float glass technology, which fire resistant properties much superior to those of sode lime glass , the main character is : * high performance to bear high temperature , our tempered borosilicate glass 4.0 can withstand 120 minutes fire test . * Ultra light ,borostilicate glass 8% less than sode lime glass * Hign soften point in fire * High ligh transmission * No SO2 pollution ,no self-explosion Borosilicate 4.0 Technical data : Size: 1830*3000mm Density (g/cm�?�³) : 2.28�?�±0.1 Co-efficient of expansion (�?�±)(20-300�¢??) : 4.0�?�±0.1�??10-6k-1 Softening point(�¢??) : 845�?�±10 Light transmission :�?� �¢?�¥90(6mm) Main usage : 4.0 building partition ,facade ,door ,ceiling ,floor 3.3 household application ,optics , lighting
We got second hand used laptop and all are in good shape delivery is all over the world We makle sure delkivery is always on time to make sure we satisfy all our clients all round the worls We assure our buyers of a good quality products and a good service that establish a long terms business relationship between the us and we also assure a safe delivery to our buyers doorstep anywhere in the world as we handle custom charges/Insurance /Tax and handling charges till shipment get deliver to buyers door step. What are the shipment terms ? A: Express( DHL, FEDEX, TNT, UPS). *Takes 3-5 Days express delivery *Tracking number will be sent to you after shipment. RETURN POLICY : This product is in a guaranteed good condition. If for some reason you are unhappy with your purchase notify us within 60 days after you receive the item. All returned items must be in their original condition and packaging and full refund of total funds includes transfer charges would be made.
Wild River Float Tube Raft Ring, inflatable leisure tube for single people Raft leisure boat one people sport tube raft ring draft tube white water raftsWild River Float Tubes Model: wild river tube 1 Materials: PVC Size: 45" total diameter & 18" center diameter Weight: 6kg Air Chamber: 1 People: 1 Application: wild river, white river, leisure water sport, raft for adventure Feature: What's more relaxing than drifting with the current on a lazy-flowing stream? Let the Wild River Tube white rafts transport you to that peaceful place. Tough PVC inner bladder inflates and deflates through a reliable Leafield C7 valve. Protective flap covers the single valve and secures with a hook-and-loop closure. Super durable, urethane-coated polyester reinforces the bottom of the tube for extra protection in shallower waters. Made by strong 0.9mm PVC materials. the handles for easy hauling or to hang onto if the ride gets bumpy. Reinforced stainless D-ring around the tube, tied the life rope for safety. Removable cover can easily be replaced in case of major wear and tear. Choose the River Tube with a non-removable mesh floor for added security and support, or the River Tube without the mesh floor for versatility.
