Product Information: Fiberglass Chopped Strand Mat is made by chopping continuous strands into unit length chopped strands which to be spread out randomly and evenly, then bonding them together with powder or emulsion binder. Chopped Strand Mat is characterized by good combination of resin, easy operation, good wet strength retention, good laminate transparency and low cost. It is used primarily for hand lay-up process, filament winding process and press molding of FRP products. It is suitable for the application by hand lay-up FRP molding, such as, various sheets and panels, boat hulls, boat tubs, cooling towers, corrosion resistant, vehicles, etc. Normal width is 1040mm/1270mm, but also can produce it according to your requirements. Product Specifications EMC100: Powder/Emulsion, 100±8g/m2, 1040/1270/2080 3600mm Width; EMC150: Powder/Emulsion, 150±12g/m2, 1040/1270/2080 3600mm Width; EMC225: Powder/Emulsion, 225±15g/m2, 1040/1270/2080 3600mm Width; EMC300: Powder/Emulsion, 300±15g/m2, 1040/1270/2080 3600mm Width; EMC380: Powder/Emulsion, 380±18g/m2, 1040/1270/2080 3600mm Width; EMC450: Powder/Emulsion, 450±20g/m2, 1040/1270/2080 3600mm Width; EMC600: Powder/Emulsion, 600�±25g/m2, 1040/1270/2080 â?3600mm Width; Product Advantages: *Short strands of fibers held together by a styrene binder *Builds up thickness quickly *Very economical and offers good stiffness. *Conforms to tight curves and corners *Can be torn of cut to size *Low cost and easy to use Packaging Information Fiberglass stitched mat is wound onto paper tube and then wrapped up with plastic film, which can be packed in a cardboard box or kraft paper. The rolls are to be horizontally placed rolls can be loaded into container directly or on pallets for Fiberglass stitched mat.
Sintered stainless steel filter discs, also called sintered metal porous filters, adopt stainless steel 316, 316L powder as raw materials and then produced through sizing, molding and sintering processes. Sintered stainless steel filter discs have found widespread use in industries such as environmental protection, petroleum, natural gas, chemical, environmental detection, instrumentation, pharmaceutical equipment, and others. Product Parameters Material:304, SS 316L, stainless steel Max pressure:5MPa Max temperature:600 degree Types:disc, plate, cup, tube cartridge, irregular Diameter Size:2.0 mm to 450 mm Height Size:1.0 mm to 100 mm Pore Size:stainless steel (0.2-120um) Product Features 1. Superior to conventional metal filter materials in terms of shape stability, impact resistance, and alternating load capacity. 2. Air permeability, with a stable separation effect 3. High loading and unloading strength, making it suited for usage in high temperature, high pressure, and corrosive situations 4. Particularly suited to high-temperature gas filtration; 5. Products of various shapes and precision can be customized according to user requirements, and can also be used for various interfaces by welding. Applications When the filter cake on the surface of the sintered metal powder filter element reaches a certain thickness, due to its high-strength performance characteristics, the filter element can be cleaned by backwashing or backflushing through a certain reverse pressure, so that the filter element can be used again. . Because of its many characteristics and the characteristics of repeated cleaning and reuse, it is widely used in water treatment, petrochemical filtration, seawater desalination, chemical filtration, resin and coating, hydroelectric power generation and other fields.
It is made of randomly yet evenly distributed chopped strands fiber of 50mm or 100mm length stitched by polyester thread. It has high tensile strength and is recommended for Pultrusion process,Uncontinuous winding Process & Laminates. Products Property: No any Binder, good compatible with Multi-Resin Optimal mechanical performance Easy workability and low cost Standard width: 120cm/127cm/160cm Max. width 320cm, Min. width 3.5cm Standard Roll weight: 45/48/60kg Packaging: Each roll is wound on paper tube (3"-4"Dia.) with plastic film and packed in individual cardboard box. 16 or 12 cartons per Pallet. The strength of fiberglass stitched mat is stronger than CSM,the price is cheaper. We export large quantity for pipe winding.We can provide big roll to reduce your replacing frequency and save your cost.We suggest stitched mat instead of chopped strand mat for pipe application. Use in close mold applications such as RTM, VARTM, SCRIMP. Can be pultruded when layered with other materials. Stitched construction allows for pattern or die cutting. Stitch Mat will not wash out in RTM process. and can be pre-wet and moved for proper placement in wet lay-up open molding. it gives uniform thickness compared to extra spray-up in open molding. it is low cost alternative for building thickness and stiffness, where the component is not weight critical. Binderless chopped E-Glass, stitched at 7 gauge The chopped strand length is 5cm or 10cm, 10cm for pultusion to improve the strength.
Simultaneous Injection-Decoration System (IMD/IML) : This technology widely used in automotive (mobility), consumer electronics, home appliance and medical devices, and supports customer to achieve unique CMF finish on mechanical parts with high quality and productivity. IMD, IML are products which add patterns and functions on the products surface at the same time as molding, by sandwiching a film with patterns or functions in a mold and pouring the melted resin into it. We can provide unique features on your product surface which cannot not be added by conventional process like painting, silk printing or pad printing. We can even add electric functions such as touch sensors / buttons and LEDs to your product surface with NISSHA IME solution. IME (In-mold Electronics) is a module product which integrates touch sensors, light source heater, etc. into a plastic panel. We can also do general molding with variety of colors, materials and finishes that suit your preference. If you already have in-house injection molding machine, we can also source you high quality heat transfer foils. Application: automotive display, CID, touch screen, car ornament, auto accessories, console, headlamp, audio panel, automotive interior, automotive exterior Pattern : Hair Line, Marble, Wood grain, Leather, Fabric, Metal look Feature : Hard coat, 3D Geometry, Hidden lit, Touch sensor Size : various sizes Capacity :100 - 650 tonnage injection molding Additional functions: Anti
Product information Product name:Tonex white SWN Color Index No: C.I.140 Synonyms: FBA 140; OBA 140,Fluorescent Brightener SWN; Optical Brightener Agent MDAC, Optical Brightener MDAC Molecular Structure: Molecular Formula : C14H17NO2 Molecular Weight: 231.28 CAS No 91-44-1/61968-71-6 C.I. No.: C.I.140 Appearance off white powder Melting point :70.5-73 Assay: 98% Fineness 200 meshes Features: 1.Multipurpose brightener with excellent whiteness, soluble in ethanol but insoluble in water. 2.having properties of good solubility and compatibility. Applications This product is mainly used for whitening of wool,natural silk, nylon, acetate fiber and triacetate fiber. It can also be usedfor whitening of cotton and cyanamide, and can be used for whitening ofcellulose fiber by adding resin. Reference dosage: The dosage is: nylon 0.05-0.3%, wool 0.05%-0.35%,acetate fiber 0.05-1.4%, triacetate fiber 0.1-2%, cylandex 0.05%-0.8%. In addition, this product can be added to soap and detergent for washingfabrics, effective in the PH=3-11 range, can improve the appearance of thefabric after washing. It can also be used for coated paper, plastic andchromatic printing coatings. Package & Storage: 25kg fiber drumor for the special demand . Should be storedin cool, dry and ventilate place, and storage time should not exceed 24 months
Garden victorian gazebo greenhouse is always used as warehouse, plant room, wedding room, meeting room, coffee room, farm house, sitting room and winter garden house. The roof material of this model is transparent polycarbonate solid sheet. The sunlight can enter into the greenhouse easily. There are many color of solid sheet for your selection. Solid Polycarbonate Sheets are made from strong, lightweight thermoplastic synthetic resin material that is extruded into solid sheets. Solid polycarbonate sheet is ideal for roofing projects that require a lot of sunlight due to its high transparency. The gazebo greenhouse is the pinnacle of expressive half-wall greenhouse engineering. The greenhouse brick base is custom made and can be tailored to your specific garden requirements. Victorian style greenhouses offer a lot of height for you and your plants. A Victorian-style greenhouse is where you can keep your favorite plants for all seasons. Thanks to its glass design, the area is filled with natural light while remaining weatherproof, allowing you to encourage the development of plants from all over the world. Fruit trees and tropical vegetation thrive in the greenhouse microclimate. Our Victorian-style greenhouses come in a variety of sizes and unique styles to fit your landscape. Advantages High light transmission Solid polycarbonate is noted for its extreme clarity which gives you unparalleled light transmission. It comes with UV protection to prevent yellowing and clarity due to constant exposure to sunlight. Lightweight Polycarbonate solid sheets weigh only half the weight of glass panels of the same size and width, making them cheaper to ship and install. High impact strength Polycarbonate solid sheets provide more strength and stability than other types of plastic sheets or hollow polycarbonate sheets. Its impact strength is estimated to be around 200 times that of common glass, and around 10 times stronger than tempered glass. Flame retardant Solid sheets give you peace of mind as they are self-extinguishing and do not amplify flames or give off toxic gases.
Customized Plastic Injection Molding Machine For Sale Rubber Mould Machine Manufacturers Overview Essential details Model Number: R002 or OEM Shaping Mode: Plastic Injection Mould Product Material: Steel Product: Mould Product name: Plastic Injection Mould Mold Steel: 1.2311,1.2738,NAK80,1.2344,S136,SKD61 etc. Material/Resin: ABS,PP,PC,PVC,POM,PA6,TPU etc. Color: Natural color or as client request Size: Customized Size Packing: Wooden box or as request to pack plastic mold. Drawing Format: STP, IGS, CAD, PRT, Certificate: ISO 9001: 2015 Certificated, RoHS, COA Supply Ability Supply Ability 50 Set/Sets per Month Packaging & delivery Packaging Details In strong wooden pallets to avoid any damages during the long transportation Lead time: Quantity(sets) 1 - 10 10 Lead time (days) 30 To be negotiated Customized Plastic Injection Molding Machine For Sale Rubber Mould Machine Manufacturers Product Description Name: Mould Plastic Material Type: ABS, ABS+PC, PP, PS, POM, PVC, TPE, TPU, Acetal,PA6.6,PA6,PA6.6+30GF,etc. Mould Steel: Assab, AISI & JIS, ALCOA,S136, 1.2311, 1.2738, NAK80, 2344, 420, 2083 Mold Base: HASCO standard, DME standard, LKM standard, Cavity No: Single, Multi Cavity, Change Insert Surface Treatment: Zinc plating,nickel plating, chromium plating,brass plating,decromet, etc. Mould Texture: EDM,VDI 3400 Code ,MOLD-TECH, Texturing,Cavity ,Core Finishing,High Polish, mirror face, Grade 3 Diamond, Paper Finish, Stone Finish. Type of Gate: Cold Runner, Hot Runner, Sprue Gate, Edge Gate, Pin Point Gate, Sub Gate Type of Ejection: Pin, Ejector Blade, Stripper, Ejector late, Ejector Sleeve, Lifter, Pneumatic Ejector.
Overview Essential details Model Number: U001 or OEM Shaping Mode: Plastic Injection Mould Product Material: Steel Product: MUD Mould Product name: Plastic Injection Mould Mold Steel: 1.2311,1.2738,NAK80,1.2344,S136,SKD61 etc. Material/Resin: ABS,PP,PC,PVC,POM,PA6,TPU etc. Color: Natural color or as client request Size: Customized Size Packing: Wooden box or as request to pack plastic mold. Drawing Format: STP, IGS, CAD, PRT, Certificate: ISO 9001: 2015 Certificated, RoHS, COA Supply Ability Supply Ability 50 Set/Sets per Month Packaging & delivery Packaging Details In strong wooden pallets to avoid any damages during the long transportation Lead time: Quantity(sets) 1 - 10 10 Lead time (days) 30 To be negotiated OEM Plastic Injection Mold Die Cast Product Description Name: Mould Plastic Material Type: ABS, ABS+PC, PP, PS, POM, PVC, TPE, TPU, Acetal,PA6.6,PA6,PA6.6+30GF,etc. Mould Steel: Assab, AISI & JIS, ALCOA,S136, 1.2311, 1.2738, NAK80, 2344, 420, 2083 Mold Base: HASCO standard, DME standard, LKM standard, Other Cavity No: Single, Multi Cavity, Change Insert Surface Treatment: Zinc plating,nickel plating, chromium plating,brass plating,decromet, etc. Mould Texture: EDM,VDI 3400 Code ,MOLD-TECH, Texturing,Cavity ,Core Finishing,High Polish, mirror face, Grade 3 Diamond, Paper Finish, Stone Finish. Type of Gate: Cold Runner, Hot Runner, Sprue Gate, Edge Gate, Pin Point Gate, Sub Gate Type of Ejection: Pin, Ejector Blade, Stripper, Ejector late, Ejector Sleeve, Lifter, Pneumatic Ejector.
Essential details Model Number: R005 or OEM Shaping Mode: Plastic Injection Mould Product Material: Steel Product: Mould Product name: Plastic Injection Mould Mold Steel: 1.2311,1.2738,NAK80,1.2344,S136,SKD61 etc. Material/Resin: ABS,PP,PC,PVC,POM,PA6,TPU etc. Color: Natural color or as client request Size: Customized Size Packing: Wooden box or as request to pack plastic mold. Drawing Format: STP, IGS, CAD, PRT, Certificate: ISO 9001: 2015 Certificated, RoHS, COA Supply Ability Supply Ability 50 Set/Sets per Month Packaging & delivery Packaging Details In strong wooden pallets to avoid any damages during the long transportation Lead time: Quantity(sets) 1 - 10 10 Lead time (days) 30 To be negotiated Product Description Name: Mould Plastic Material Type: ABS, ABS+PC, PP, PS, POM, PVC, TPE, TPU, Acetal,PA6.6,PA6,PA6.6+30GF,etc. Mould Steel: Assab, AISI & JIS, ALCOA,S136, 1.2311, 1.2738, NAK80, 2344, 420, 2083 Mold Base: standard, DME standard, LKM standard, PUNCH, , Other Cavity No: Single, Multi Cavity, Change Insert Surface Treatment: Zinc plating,nickel plating, chromium plating,brass plating,decromet, etc. Mould Texture: EDM,VDI 3400 Code ,MOLD-TECH, Texturing,Cavity ,Core Finishing,High Polish, mirror face, Grade 3 Diamond, Paper Finish, Stone Finish. Type of Gate: Cold Runner, Hot Runner, Sprue Gate, Edge Gate, Pin Point Gate, Sub Gate Type of Ejection: Pin, Ejector Blade, Stripper, Ejector late, Ejector Sleeve, Lifter, Pneumatic Ejector.
Chemical name: Dioctyl terephthalate Cas No.:6422-86-2 Einecs No.:229-176-9 Relative Molecular mass: 390.5 Molecular Formula: C24H38O4 Product specifications: Parameter Unit Methods Specifications Color, Pt-Co Hazen GB/T 1 664. â?¤30 Acid Va lue : mgK0H/g GB/T 1 668 â?¤0. 07 Dens ity (20�°C) g/cm3 GB/T 4472 0.981-0. 985 Water content wt% GB 11133 â?¤0.1 Flash point �°C GB 1671 â?¥210 Ester Content wt% GC â?¥99.0Major performance: 1.Dotp is a sort of high-performance primary plasticizer with good electrothermal properties. Its volume resistivity is ten-twenty times of DOP's. Good plasticating effect and low volatility on cable materials makes it be widely used on the heat-resisting, high insulation product. It is the ideal plasticizer for the production of 70 degrees C. cable material and other volatility-resist PVC products. 2.Meanwhile it has favourable cold-resistance, heat-resistance, extraction-resistance performace, with low volatility and high plasticizing efficiency. In its downstream products, good durability, soap water resistance and softness in low temp. was been found. It is suitable for the plasticizer of PVC resins, such as high-insulation PVC cables. 3.This product can be mixed with DOP at free percentage. 4.This product can reduce viscosity and increase preserve life in the application of plasticized paste. Application Guide: Widely used in cable materials, insulating wires, high-grade paint, coating, PVC gloves, artificial leather, etc.
1. Because the BMC material contains a large amount of glass fiber and filler, it will block the gap between the workpiece and the exhaust groove during molding. Exhaust is equal to discharge, and the exhaust vent should be easy to clean. The place that cannot be cleaned should be designed to take into account the parting surface structure and the cold trough. 2.The resin and filler will block the gap between the workpieces during molding. It is difficult to disassemble after long-term use and cooling. In addition to the thermal expansion of the metal and the accuracy of the product, the matching gap between the workpieces should be fully considered during processing. 3.Because BMC material contains high glass fiber, the flow is poor, the hardness of the material itself is high, and the mold is very worn. When designing, different materials should be considered, and the quenching hardness of the mold material (vacuum heat treatment) HRC50 or above), tempering temperature and surface treatment have high requirements (the mold core is recommended to use Japan's Datong H13 or Sweden 8407) to effectively ensure the use of the mold. 4.The open cavity distribution pattern should be reasonable: the balance of each cavity in a mold is crucial because it is the direct killer of the pass rate. It also affects the appearance of the product. When the balance is not good, the B mode has a problem when the A cavity is satisfied. Conversely, when the B mode satisfies the A mode, the process is difficult to satisfy. 5.BMC materials are very sensitive to temperature. When the temperature difference is large, the product will be deformed, cracked and oversized. Therefore, the mold should be more temperature-detected, and the temperature balance should be fully considered when designing the heating rod. 6.The design of the runner should be as low-pressure and low-speed as possible. The position and angle of the runner should avoid the direct impact on the easily deformable workpiece and the effective discharge of the gas inside the cavity.
BMC Compression Mould Plastic Mould Customize Design bmc2BMC molding compound is an abbreviation of Bulk (Dough) molding compound, that is, a bulk molding compound. BMC molding compound is often referred to as unsaturated polyester bulk molding compound in China. The main raw material is a dough-like prepreg which is sufficiently mixed with GF (short-cut glass fiber), UP (unsaturated resin), MD (filler), and various additives. DMC materials were first applied in the former West Germany and the United Kingdom in the 1960s, and then in the United States and Japan in the 1970s and 1980s. Because BMC bulk molding compound has excellent electrical properties, mechanical properties, heat resistance, chemical resistance, and adapt to various molding processes, it can meet the performance requirements of various products, so it is more and more popular by users. Application of BMC molding compound First, electrical components Low-voltage categories: RT series, isolating switches, air switches, switchboards, meter housings, etc.; High-voltage type: insulator, insulation cover, arc-extinguishing cover, closed lead plate, ZW, ZN vacuum series. Second, auto parts lights, that is, Japanese headlight reflectors are almost all made with DMC; Automobile igniter, separation disc and trim board, speaker box, etc.; Third, the motor components Air conditioning motor, motor shaft, coil bobbin, electric and pneumatic components. Fourth, daily necessities Microwave tableware, electric iron shell and so on. BMC series molding compound is packaged in a composite film bag, each bag is 25 kg, and then packed into a carton after being wrapped; Beware of heavy pressure, heat and damage to packaging during transportation; The storage period is in the dry warehouse with the temperature below 25 and avoiding sunlight. The production date is three months from the date of production.
1. Technology (1) Technology Introduction Sand casting, also known as sand mould casting, is a metal casting process characterized by using sand as the mold material. The term "sand casting" can also refer to an object produced via the sand casting process. Sand castings are produced in specialized factories called foundries. Over 70% of all metal castings are produced via sand casting process. Sand casting is relatively cheap and sufficiently refractory even for steel foundry use. In addition to the sand, a suitable bonding agent (usually clay) is mixed or occurs with the sand. The mixture is moistened, typically with water, but sometimes with other substances, to develop the strength and plasticity of the clay and to make the aggregate suitable for molding. The sand is typically contained in a system of frames or mold boxes known as a flask. The mold cavities and gate system are created by compacting the sand around models, or patterns, or carved directly into the sand. (2) Process Parameters Process : Resin Sand, Hot Sand, Precoated Sand, Green Sand ,Clay Sand for option. Weight from 0.5kg to 2,000kg. Surface Finish: Polishing, oiled(rust-prevented), zinc-plated, chrome-plated, hot dip galvanized, sandblasting, painting, powder-coating General Tolerance: ISO8062-CT12 Surface Roughness: Ra 12.5 (3) Material Introduction Sand casting material ranging from Gray Iron, Ductile Iron, Malleable Iron, Steel, Stainless Steel, Aluminum to Brass. Commonly used material :HT100,HT150,HT200,HT250ï¼?QT450-1,QT600-3 2. Product Introduction Brand Name: WOTECH Specification: Customized requirement Material: Iron Application: Industry Place of Origin: Shandong, China Payment Terms: L/C,D/A,D/P,T/T Packaging: Outer :Non-coniferous wooden package Inner: Carton box Port:Qingdao/Ningbo/Shanghai/Shenzhen/Guangzhou Engineers: 8 professional engineers
NEOFLON PFA AP-Series NEOFLON PFA is a copolymer of tetrafluoroethylene and perfluoroalkyl vinylether. It is a perfluoro polymer consisting of only carbon atoms and fluorine atoms without any hydrogen atom. It has the same excellent performance as PTFE in a wide range from extremely low to high temperatures. In addition, it has excellent transparency, mechanical strength at high temperature. It can be molded in the same molding method as general thermoplastic resins. Grades and Features of AP-Series Grades MFR (g/10 min.) Features AP-201 20 - 30 Superior in melt flowability. Suitable for injection-molded articles that have complex shape, and for ultrafine thin-wire coating (AWG34 - 44). AP-202 65 - 80 Excellent melt flowability. Suitable for injection-molded articles that have complex shape, and for thin-wire coating (AWG44 - 52). AP-210 10 - 17 Good melt flowability. Suitable for injection molding. AP-230 1.5 - 2.5 Superior in stress crack resistance. Suitable for extrusion and transfer molding. AP-201SH 20 - 30 High purity grade. Superior in melt flowability. Suitable for complex shape articles. AP-211SH 10 - 17 High purity grade. Long-term flexibility and good stress crack resistance. Suitable for joints and parts for pumps. AP-215SH 10 - 17 High purity grade. Suitable for injection molding. Suitable for joints and parts for pumps. AP-231SH 1.5 - 2.5 High purity grade. Long-term flexibility and good stress crack resistance. Suitable for extrusion and transfer molding. AP-210AS 11 - 14 Anti-static grade. Suitable for injection molding. AP-230AS 1.5 - 3.0 Anti-static grade. Suitable for extrusion molding. AP-230ASL 1.0 - 2.5 Anti-static grade. Suitable for extrusion molding.
Product Name : Insulating material for wires and cables Product Description : The ordinary 70 â?? -90 â?? PVC insulation and sheath materials developed by Zibo Qiwangke Industry and Trade Co., Ltd. are based on high-quality Qilu PVC resin, and add appropriate amounts of plasticizers, lubricants, stabilizers and other processing aids. The plastic granules obtained by mixing and extrusion granulation have excellent physical and mechanical properties, insulation and dielectric properties, and good processing properties. The cables processed with this product can meet the requirements of users, and can be widely used in subways, airports, power stations, high-rise buildings, computer centers, television centers and other places that require high cable requirements. Price of product ( USD price or FOB price) : USD920- USD980 per MT FOB Qingdao,China Product origin : Zibo,Shandong,China Key Specifications/Special Features : The PVC insulation / sheathing material produced by our company has good processing performance, there are no special requirements for extrusion equipment, and it can be processed by ordinary PVC cable extruder. The process conditions can be based on the extrusion process of ordinary PVC cable material. The applicable process temperature range is wide, has excellent processing stability, and the formed cable has good appearance and insulation properties. Minimum Order Size and Packgaing details : The company's products are standard color or specific color granules. They are packed in three-in-one composite packaging bags and film inner village bags. The net content of each bag is 25 �± 02Kg. Avoid rain and introduction of impurities during transportation. This product should be stored in a clean, cool, dry and ventilated warehouse.
Product Name : Insulating material for wires and cables Product Description : The ordinary 70 â?? -90 â?? PVC insulation and sheath materials developed by Zibo Qiwangke Industry and Trade Co., Ltd. are based on high-quality Qilu PVC resin, and add appropriate amounts of plasticizers, lubricants, stabilizers and other processing aids. The plastic granules obtained by mixing and extrusion granulation have excellent physical and mechanical properties, insulation and dielectric properties, and good processing properties. The cables processed with this product can meet the requirements of users, and can be widely used in subways, airports, power stations, high-rise buildings, computer centers, television centers and other places that require high cable requirements. Price of product ( USD price or FOB price) : USD920- USD980 per MT FOB Qingdao,China Product origin : Zibo,Shandong,China Key Specifications/Special Features : The PVC insulation / sheathing material produced by our company has good processing performance, there are no special requirements for extrusion equipment, and it can be processed by ordinary PVC cable extruder. The process conditions can be based on the extrusion process of ordinary PVC cable material. The applicable process temperature range is wide, has excellent processing stability, and the formed cable has good appearance and insulation properties. Minimum Order Size and Packgaing details : The company's products are standard color or specific color granules. They are packed in three-in-one composite packaging bags and film inner village bags. The net content of each bag is 25 �± 02Kg. Avoid rain and introduction of impurities during transportation. This product should be stored in a clean, cool, dry and ventilated warehouse.
Product Name : Insulating material for wires and cables Product Description : The ordinary 70 â?? -90 â?? PVC insulation and sheath materials developed by Zibo Qiwangke Industry and Trade Co., Ltd. are based on high-quality Qilu PVC resin, and add appropriate amounts of plasticizers, lubricants, stabilizers and other processing aids. The plastic granules obtained by mixing and extrusion granulation have excellent physical and mechanical properties, insulation and dielectric properties, and good processing properties. The cables processed with this product can meet the requirements of users, and can be widely used in subways, airports, power stations, high-rise buildings, computer centers, television centers and other places that require high cable requirements. Price of product ( USD price or FOB price) : USD920- USD980 per MT FOB Qingdao,China Product origin : Zibo,Shandong,China Key Specifications/Special Features : The PVC insulation / sheathing material produced by our company has good processing performance, there are no special requirements for extrusion equipment, and it can be processed by ordinary PVC cable extruder. The process conditions can be based on the extrusion process of ordinary PVC cable material. The applicable process temperature range is wide, has excellent processing stability, and the formed cable has good appearance and insulation properties. Minimum Order Size and Packgaing details : The company's products are standard color or specific color granules. They are packed in three-in-one composite packaging bags and film inner village bags. The net content of each bag is 25 �± 02Kg. Avoid rain and introduction of impurities during transportation. This product should be stored in a clean, cool, dry and ventilated warehouse.
Low pt-co plasticizer special for medical gloves Plasticizer e01 Description E01 is kind of special plasticizer developed for medical gloves manufacturer which requests low viscosity plasticizer. Comparing to other plasticizers, our product is processed from food grade palm oil, it is eco-friendly plasticizer passed sgs certificate compliance with eu rohs, reach, svhc and bpa regulations. A. Viscosity obviously lower than same item of similar plastic Izer because some pvc products limit to use high viscosity additive B. Good stability, high plasticizing efficiency, combined with main plasticizer dotp, dinp or tbc will not affect finished product quality. C. Good compatibility with pv c raw materials, replace 30% main plasticizer. D. Competitive pric E, reduc es c omposite cost of gloves. Applications 1. Passed sgs certificate compliance with eu rohs, reach, svhc and bpa regulations. 2. Viscosity is 30 cst (40 ?), solve high viscosity limitation problem, not affects settlement behavior of paste resin. 3. High flash point >200 ?, compliance with processing requirements. 4. Good stability, high plasticizing efficency, mix with main plasticizer would not affect gloves quality. Specification Pt-co 60 Acid value(mgkoh/g ) 0.30 Heating decrease volume(125 oc, 2 h) 0.50 Density g/ml(20 oc) 1.00-1.05 Viscosity(mm2/s) 30 Flash point(oc) >200 Price Delivery port : tianjin/qingdao Packaging & delivery Packing :200kg iron drum/20mt flexibag/1mt ibc drum Delivery lead time : within 10-20 days after receiving the deposit Supply ability : 20, 000 ton/year
Basic Info Model NO.: H7 Headlight Socket Trademark: Invitech Transport Package: 1000 pcs/carton Specification: 6.5kg/carton Origin: China HS Code: 853990 Product Description 1. Product Name: H7 Headlight Socket 2. Product Type: OSRAM H7 base AFTM 3. Material: SUS 430 4. Resin Type: Bakelite black 5. Usage: OSRAM H7 PX26D base AFTM 6. Product Dimension: Height: Max 19.1mm Diameter: Φ33.9±0.1mm Distance of pin: 11.5mm Diameter of hole: 0.8+0.1/-0.05mm 7. Product Feature: Temperature resistance: 140-180; Terminal tensile strength: 140 N Company Information Our Services 1. Sample order We accept sample order. But of course if you order more, you will get better discount. 2. Customized Service We provide customized service for the package. You can provide your design of the package and then we can print it for you. FAQ 1. Q: What payment method your company accepts? A: We accept T/T payment. 2. Q: How long for the production time? A: Normally it will take about 15-25 days for manufacturing. And we usually have them in stock. 3. Q: What is your location in China? A: We are located in Zhejiang province, southeast of China. 4. Q: How many employees do you have? A: About 90 persons. 5. Q: Which countries do you export to now? A: Most to India, Korea, etc.
High glossy 1*22 PVC Edge Banding for Kitchen Product Detail Flexible Plastic Strips for Kitchen Color solid color Flexible Plastic Strips for Kitchen Usage furniture accesories Flexible Plastic Strips for Kitchen Raw Material pvc resin Flexible Plastic Strips for Kitchen Size 1*22 Flexible Plastic Strips for Kitchen Surface Matt Flexible Plastic Strips for Kitchen Certificate ISO9001 Flexible Plastic Strips for Kitchen Name woodgrain pvc edge banding Flexible Plastic Strips for Kitchen Feature Anti-Bacteria Flexible Plastic Strips for KitchenThickness 0.4mm-3mm Flexible Plastic Strips for Kitchen Product name High glossy 1*22 Solid Color PVC Edge Banding Flexible Plastic Strips for Kitchen Product Keywords Flexible Plastic Strips for Kitchen Quality assurance:Xiamen Yimin edge banding quality is the NO. 1 from China since we keep on offering products as below: 1) Smooth UV finishing with scratch resistant and color fade resistant. 2) Close base color and surface color matching without white color visible while sealing on board 3) Excellent primer on back side and perfect adhesive with hot melt glue. 4) Excellent flexibility, flection and stretch. Products specification: Thickness: 0. 4 ~ 6mm Width: 15~ 130mm We can offer any designs and colors on request from customer.
