FH SERIES OF PRODUCTS: FH products are Pure nonionic derived the endosperm of guar polysaccharide (Cyamopsos tetragonolobus). The products are unique with ultra-high viscosity with fastest hydration characteristics as shown in Figure 1 below. Also, when added with other drilling components, to seawater, a KCl solution or other aqueous system, the product suspension disperses readily without lumping, even under low-shear conditions generating most of its full viscosity within just a few minutes. PRODUCT COMPATIBILITY: FH series of products are compatible with most of the chemicals and auxiliaries used in drilling operations. However, the products are not compatible with Arabic and Crystal gums. Also, in presence of borates they form elastic gel. PRODUCT APPLICATIONS: FH series of products are natural, high viscosity, fast hydrating non-Newtonian hydrocolloids with suitable cross linking components in diesel slurries and are versatile for continuous mix applications, where extremely fast hydration and subsequent viscosity development is required. They are excellent viscosifiers, stabilizers, thickeners and suspending agent for use in oil-drilling, workover fluids and several other oilfield applications like hydraulic fracturing, oil well stimulation, mud drilling, oil well capping, flocculent and liquid shoring etc. The product is used as a surfactant; synthetic polymer and deformer ideally suited for all rheological requirements of water based and brine based drilling fluids. Specifications:- PRODUCT : FH-35 FH-38 FH-42 CAS No. : 9000-30-0 9000-30-0 9000-30-0 Granulation : FINE FINE FINE APPEARANCE : OFF WHITE POWDER MOISTURE : 8% Max. 8% Max. 8% Max. PROTEIN (N X 6.25) : 5.0% Max 5.0% Max 5.0% Max ASH : 1.5% Max. 1.5% Max. 1.5% Max. ACID INSOLUBLE RESIDUE (A.I.R.) : 3% Max. 3% Max. 3% Max. CARBOHYDRATE (incl gum by difference) : 82% Min 82% Min 82% Min pH (1% Solution) : 5.5 ? 6.5 5.5 ? 6.5 5.5 ? 6.5 VISCOSITY : (0.48% Product in 2% KCL Sol. 2.5 mins mix @1500 RPM in waring blender) Fann 35sa Viscometer at 300 RPM, 25�C 3 Mins : 35 3 Min:38 3 Mins : 42 5 Mins : 37 5 Mins : 39 5 Mins : 43 30 Mins : 39 30 Mins : 42 30 Mins : 45 60 Mins : 40 60 Mins : 43 60 Mins : 47
Bitumen Primer * Bitumen Primer is Bituminous air curing ready mixed Acid & Alkali resistant special primer. Application * Concrete surface must be clean, dry and rough. No primer should be applied over smooth and wet surface. * After cleaning the concrete surface, one coat of Bitumen Primer should be applied with brush and allow to dry thoroughly. * The drying time will depend upon the temperature. * 24 Month at the temperature 30C (+2OC) Packing * Bitumen Primer: 25 Liter Drum Note * Bitumen Primer contains volatile and slightly toxic solvent. Keep away from spark and open flames at working area. * Bitumen premier it is manufactured using bitumen solution which is used for sealing of prime porous and non-porous surface, and also to protect residential and commercial building. * Bitumen Primer is used to protect substrate against corrosive attack, is suggested to apply anti-corrosive primer.It is best for protection against sub-striate against atmospheric corrosion and chemical corrosion. It is a mixed substance made up of organic liquids that are highly sticky, water proof, viscous,acid proof as with all surface coating, good Bitumen Premier is used for long life of the system. it is applied by brush or roller and allowed to dry before any water proofing treatment so to avoid solvent it is used in defects such as cracks, broken mortar joints, etc. are to be repaired prior to Bitumen primer application. Product Details: Grade Standard Technical Grade Physical State - Liquid Usage - Industrial Color - Black Characteristics: Appearance/Color - Pasty liquid/ black Chemical Base - Bituminous rubber emulsion. Density - 1.0 kg/l Curing Speed/ Rate - 3 - 4 hours Tack free after - 5 - 10 hours Cured after - 2 - 4 days (Dependent on ambient Solid Content by - temperature, substrate temperature, Weight - relative Water Content by weight - humidity and thickness of the coating) Bitumen Content - 41% by weight - Thixotropic (The viscosity can be adjusted by - Viscosity adding up to max. 5% of clean water. - Stir well prior use) - For light protection: 1.0 mm min. Coating - For greater protection: ~ 1.5 - 2.0 mm Thickness applied - in two coats. Water Penetration - 48 h, 1 bar: 78.5 cm2: 0 ml under Hydrostatic - 96 h, 4 bar: 78.5 cm2: 33 ml Pressure - Water vapor 6 x 10-7 mg / hmPa Permeability Service - -30 C to 200 C Temperature - Adhesion Concrete - Very good, Timber: Very good, Metal: Moderate Glass: Poor
Form: Powder (loose packing 20kgs/bag) or block (compressed packing). Compression Ratio: Over 75 Liters / Block. Impurities/sand: 3% Max. Moisture: 15-20% Max. PH: 5.8 to 6.8. Block Size: 30 x 30 x 15 cm. Fiber length: Less than 2cm. Weight : 5kg (+/- 3%). Electric Conductivity (E.C): High EC (Animal Bedding): 3.5 - 5 mS/cm. Low EC (For Plant Growth) < 0.5 mS/cm.
We are supplying Magnesium sulphate anhydrous/heptahydrate/monohydrate Magnesium Sulphate Hepta Hydrate Magnesium as Mg - 9.7% (min.) Magnesium as MgO - 16.3% Sulphur as S - 12.4% pH of 5% solution - 6 to 7 Physical Appearance: White crystals Magnesium sulfate can be used in leather making, explosives, paper making, porcelain, fertilizer, and oral laxative in medical treatment. Magnesium sulfate is used as a fertilizer in agriculture because magnesium is one of the main components of chlorophyll, and its advantage over other fertilizers is higher solubility. Industry It is used in leather making, explosives, fertilizer, paper making, porcelain, printing and dyeing materials, lead-acid battery and other industries.
We are supplying Magnesium sulphate anhydrous/heptahydrate/monohydrate Magnesium Sulphate Hepta Hydrate Magnesium as Mg - 9.7% (min.) Magnesium as MgO - 16.3% Sulphur as S - 12.4% pH of 5% solution - 6 to 7 Physical Appearance: White crystals Magnesium sulfate can be used in leather making, explosives, paper making, porcelain, fertilizer, and oral laxative in medical treatment. Magnesium sulfate is used as a fertilizer in agriculture because magnesium is one of the main components of chlorophyll, and its advantage over other fertilizers is higher solubility. Industry It is used in leather making, explosives, fertilizer, paper making, porcelain, printing and dyeing materials, lead-acid battery and other industries.
Item: Sea Grapes Origin: Vietnam Packing: 100 gr/zip Color: Dark Green Usage : Step 1. Put salted sea grapes in a bowl of clean water ( 1 liters of water for 40 grams of salted sea grapes ). Soaking for 2 -3 minutes, it will be refreshed again, 40 grams salted sea grapes bloom into 100 grams sea grapes Step 2. Washing through with clean water 2 to 3 times. Step 3. Soaking sea grapes into a bowl of clean water for 3 to 5 minutes or longer depending on the taste of each person. Step 4. You can soak sea grapes in a bowl of ice water to make it more crunchy, cold and delicious. Step 5. Having directly like vegetables with any sauces Storage: 6 Months At Normal Temperature And 12 Months In Refrigerator (0C - 10C
Product name: Coconut Peat Brand name: 99 Gold Data Block size: 30 x 30 x 15 cm Weight: 5 kgs (+/- 3%) pH: 5.8 to 6.8 Compression Ratio: Over 75 Liters / Block Moisture: 15 â?? 20% max Electric Conductivity (E.C): o High EC (Animal Bedding): 3.5 - 5 mS/cm. o Low EC (For Plant Growth) < 0.5 mS/cm. Impurities/sand: 3% max Fiber length: Less than 2cm Price: Negotiation Packing: In PP bag 20kgs, or 5kg/block, 192 blocks/pallet, 24 pallets/40ft (23 MTs) Payment method: T/T 40 in advance, 60% on scan bill, L/C at sight 100% Delivery time: 10 - 20 days