Ultra-fine with consistent particle size High purity High whiteness typical High brightness typical - Ultrafine product with purity and consistent particle size. Our PMC - 10 is good funtional filler in paper which help to save cost of fiber with unchange paper quality. PMC - 10 could be applied as coating pigment also for its small particle size and high whitness typical and brightness typical. - For plastics application, PMC - 10 low density should result in the output of processing lines while achieving improved impact strength and higher stiffness. The applications are film, PVC pipe, cable, PVC profile, roofing. - PMC - 10 filler in paint would result in opacity, wet-scrub resistance. Chemical Analysis Calcium Carbonate Typical : MIN 98 % - Magnecium Oxide Typical : MAX 0.4 % - Silica Typical : MAX 0.2 % - Aluminium Oxide Typical : MAX 0.1 % - Iron Oxide Typical ( Max ) : MAX 0.02 % - Loss on Ignition Typical : MAX 43.8 % - PH Value Typical : 8 TO 9 Physical Properties (product before coating stearic acid): - Specific Gravity Typical : 2.7 g / cm3 - Brightness Typical : MIN 95 % - Whiteness Typical : MIN 97 % - Max Moisture Typical : MAX 0.2 % - Hardness Typical : MAX 3 Moh - Oil Absorption Typical : 23 g/100 g CaCO3 Test Methods - Chemical Analysis Method - Particle Laser Difraction : MALVERN ( Made in England ) Whiteness Analyser : MINOLTA CR-200/CR-210 ( Made in Japan ) Please contact for further product information, application information, price and term 25 Kgs PP PE Bags 50 Kgs PP PE Bags 25 MT to 27 MT per 20 feet container
40-500 gsm 100-200 cms
Features and Benefits: Working principle- The flow through the nozzle creats a vacuum at the valve seat. Air is drawn in through the sensing port at the tip of the spout, through the safety cut out, past the diaphragm,and into the fuel. The valve will remain open while the air flows freely. When the fuel reaches the sensing port, suction builds up rapidly until it lifts the diaphragm and trips the automatic action which shuts the valve.The mechanic also trips if the ball of the safety cut off rolls back to obstruct the free air flow.It will also occur if the spout is pointed upwards or if the nozzle is dropped onto the ground. The valve opens with the flow, allowing smooth low control for"to-the penny" dispensing. It closes against the flow for a soft shock-less closure. All type of guards are available if requested. All type of guards with block magnet are available if requested. "ZVA" logo or blank are available. 100% Factory tested. Material Body Aluminum Spout Aluminum Swivel Aluminum Seals Buna-N, Viton Covers PVC Technical Specifical Working Pressure 0.2 Mpa Flow Rate 15 - 45 L/m Auto Shut-off sensibility 0.1 second Spout Internal Diameter 16mm Intel Thread M34 ¡¨¢ 1.5 Net Weight 1.1 KG Order Specifications Item No. Swivel Inlet Size ZVA DN1901 without swivel M34 ¡¨¢ 1.5 ZVA DN1902 with swivel Female, BSP, 3/4" ZVA DN1903 with swivel Female, NPT, 3/4" ZVA DN1904 with swivel Male, BSP, 3/4" ZVA DN1905 with swivel Male, NPT, 3/4" ZVA DN1906 with swivel Female, BSP, 1" ZVA DN1907 with swivel Female, NPT, 1" ZVA DN1908 with swivel Male, BSP, 1" ZVA DN1909 with swivel Male, NPT, 1" Color Options Red, Green, Blue, Yellow, Orange, Black Each Fuel Nozzle with Plastic Bag, Then with Box
Features and Benefits: Ø Low profile aluminum body-light weight, easier to handle, provides an attractive, image enhancing appearance. Ø Full hand insulator-protects both nozzle and vehicle, and insulates user's hands. Ø Hold-open rack is available for full service application-the one hand control means easy setting to flow rate for customer convenience. Ø Easily replaced spout-simply remove the spout retaining screw. Replacement provides and entirely new outlet check valve. Kits are available from TDW. Ø Suitable for diesel, kerosene, gasoline and gasoline with ethanol blends. Ø 100% Factory Tested. Material Body Aluminum Lever and lever guard Duratuff Main stem Extra hard stainless steel Seals Buna-N, Viton Technical Specifical Working Pressure 0.2 Mpa Auto Shut-off sensibility 0.1 second Thread NPT/BSPT Spout Outlet Diameter 15/16", 13/16" Inlet Size 3/4" Flow Rate 18-60 L/m(15/16"), 15-40 L/m(13/16") Net Weight 1.15 KG Color Options Red, Green, Blue, Yellow, Orange, Black Order Specifications Item No. Inlet Thread Spout O.D. TDW-11A01 3/4" NPT 13/16" TDW-11A02 3/4" NPT 15/16" TDW-11A03 3/4" NPT 13/16" TDW-11A04 3/4" NPT 15/16" Each Fuel Nozzle with Plastic Bag, Then with Box
bailed old cartoon boxes used bailed
Dimensions from 8mm to 32 mm. Length 12 mt or up to requested lengths. As per buyer's requested packingmethod
Features and Benefits: For all normal gasoline fuels - leaded or unleaded. Not suitable for water and hydrous liquids, alcohols, solvents, viscous oils and diesel fuels. TRISTOP - Venturi controlled automatic shut-off on request and safety cut-out attitude valve(protection when tilting and falling), 3- speed lever latch with removable latch pin. Full adjustable control of the vapour volume flow independent of the fuel flow delivery. ON/OFF function - Secure termination of the vapour line when there is no fuel flow. Important when connecting two or more hoses to a vacuum pump. Design "GR"- with vapour suction apout, internal vapour channel and COAX hose coupling M34*1.5. Reduced spout DN 16 acc. To ISO9158. Design "GRVP" - additionally with gas-and proportional valve GVP. 100% Factory Tested. Material Body Aluminum Spout Aluminum Vapour Suction Spout Bronze Springs Galvanised or Stainless Steel Diaphragm Buna-N, Polyurethane, Viton Seals Buna-N, Polyurethane, Viton Inner Parts Brass, Bronze, Acetal Resin/Delrin or Ultrapek Covers PVC Technical Specifical Working Pressure 0.05 - 0.35 Mpa Max Flow Rate 45 L/m Temperature =A17 Inlet Thread M34¡¨¢1.5 Net Weight 1.17 KG Color Options Red, Green, Black Order Specifications Item No. Proportional Valve ZVA-BT200GR Without Proportional Valve ZVA-BT200 GRVP With Proportional Valve Each Fuel Nozzle with Plastic Bag, Then with Box
Features and Benefits: Even, Smooth spray pattern - Minimizes diesel foaming and false shut-off Extra long anchor spring - Keeps the nozzle secure in most large fill opening. Help reduces spills - A unique two-stage lever design assures a positive shut-off, even if held wide open. Three Position hold-open device - One finger control of hold-open mechanism means easy setting of flow rate. Easily replaced spouts -Simply remove three screws, Replacement kits are readily available from TDW. Dash-pot Action - For smoother closing action and reduced line shock. Dual Poppet - Easy to open nozzle against high pressure. Available with flow lock - Designed to shut off automatically when the spout is tipped ip, limiting spillage. Suitable for diesel, kerosene, gasoline and gasoline with ethanol blends. 100% Factory Tested. TDW-7H UL LISTED. Material Body Aluminum Lever and lever guard Duratuff Main stem Extra hard stainless steel Seals Buna-N, Viton Technical Specifical Working Pressure 0.2 Mpa Auto Shut-off sensibility 0.1 second Inlet Size 1" Thread NPT/BSPT Spout Outlet Diameter 30 mm, 28.7 mm Flow Rate 20 - 120 L/m Net Weight 1.55 KG Color Options Red, Green, Blue, Yellow, Black Order Specifications Item No. Inlet Thread Spout O.D. TDW-7H01 1" NPT 28.7 mm TDW-7H02 1" NPT 30 mm TDW-7H03 1" BSPT 28.7 mm TDW-7H04 1" BSPT 30 mm TDW-7HB01 1" NPT 28.7 mm TDW-7HB02 1" NPT 30 mm TDW-7HB03 1" BSPT 28.7 mm TDW-7HB04 1" BSPT 30 mm Each Fuel Nozzle with Plastic Bag, Then with Box
Chrome concentrate grade 44%rej.42% Chrome lumpy grade 38%rej36% 5 000mts per month
Grade:YG15;YGH30 material:100% virgin material and HIP sintered type: PR/CA/FO/CO/RT cartons
Item no.: mt-qj8000 Application: universal type Product features: Suitable for the cars which needn't interface Supports four-way surveillance video, makes your driving no-blind spot Manual switch to view each camera Defending the vibration function Neutral packing, color box or accoding to customer's request
Factory No.: HZ-Ag25C* Chemical Elements(%):Ag25,Cu35,Zn26,Cd14 Application:Suitable for most metals,e.g.steel,stainless steel,copper,nickel and their alloys. Diameter: 0.5-5.0mm; Length: 450-1000mm;
HUAZHONG HZ-CUP-2 brazing alloy is used for the brazing of copper and copper alloys, brass and bronze. It can also be used on silver, tungsten and molybdenum. It is primarily used for the joining of copper to copper on vibration free joints. It is very effective for joining tight fitting and tubing. HZ-CUP-2 is extremely fluid at temperatures and will penetrate joints with very little clearance. The phosphorus content of HZ-CUP-2 acts as a fluxing agent and no flux is necessary when brazing copper to copper joints. However, when used with a copper alloy or one of the brazeable metals, a flux must be used to promote wetting, bonding and flow throughout the joint. Diameter: 0.5-5.0mm; Length: 200-1000mm; Operating Temperature: 710-820; Chemical Elements(%): P:6.8-7.2, Cu:Bal.
With the strong oxidizing property, it can decompose the harmful gas with reductibility in the air in order to clean the air, and it also has the high efficiency to removal other harmful gases such as the ethylene, hydrogen sulfide, sulfur dioxide, chlorine, formaldehyde, nitric oxide, etc. 1.1*1.1*1.3 1 ton, 1 pallet
Medical crepe paper / medical wrapping paper / disposable crepe paper Weight: 45gsm or 60gsm Color: white / blue / green Shape: by sheets or rolls Sheet Size: 30x30cm ~ 120x120cm Roll Size: 30 ~ 120cm width x 100m length Sterilization Method: Steam and EO OEM manufacture: available Feature: water resistant, breathable, eco-friendly, non-toxic Application: Can be used as inner and outer sterilization wrapping for various kinds of medical devices Free samples will be provided, the customers bear the courier fee Shipping Port: Ningbo or Shanghai Specification: Size W*L (cm) PCS/CTN CTN Size L*W*H (cm) N.W. (KG/CTN) G.W. (KG/CTN) 30x30 1000 32x32x17 5.40 6.00 40x40 1000 42x42x17 9.60 10.00 45x45 1000 47x47x17 12.20 12.70 50x50 1000 52x52x17 15.00 15.50 60x60 1000 62x62x17 21.60 22.50 70x70 500 72x39x17 14.70 15.70 75x75 500 77x42x17 16.90 17.90 80x80 500 82x45x17 19.20 20.20 90x90 250 92x49x11 12.20 13.20 100x100 250 102x54x11 15.00 16.00 120x120 200 122x64x11 17.30 18.30 by carton
Machine function 1.Apply high precision import forging doctor blade, smaller error, thin & even gel coat coating 2.Gel coat curing area apply clip flatten roller designed by dnuo technology company, easy operation &good tensioning effect 3.Easy operation based on plc intellectual control system. Only short-term training can make operators complete production independently 4.Unique arithmetic on temperature control makes oven heating fast, temperature control precise. Which improve quality of products, reduce energy consumption and shorten the preparing time effectively. 5.Roving chopper speed can be synchronous with the production line. 6.Special cross cutting machine and good synchronization performance make cutting accurately. 7.All the machine parts adopt international standard steel make machine with high stability 8.System failure can be automatically alarmed and show fault point. Make maintenance easily 9.Particular parts adopt special purpose wire, durable in use 10.Size and layout of machine can be made according to customer requirements Basic parameter Operation staff: 4-7 people Production speed: 2-10m/min Sheet width: maximum effective width of flat sheet is 1500mm Wave height: maximum 130mm Sheet thickness: 0.4-4.0mm Gel coat thickness: 0.2-0.4mm Machine main dimension: upper gel coat:54m*4m*5m Lower gel coat:60m*1.85m*3.5m Power requirement: 100kva Power consumption: actual power consumption is about 35kw/h
Machine function 1.Apply high precision import forging doctor blade, smaller error, thin & even gel coat coating 2.Gel coat curing area apply clip flatten roller designed by dnuo technology company, easy operation &good tensioning effect 3.Easy operation based on plc intellectual control system. Only short-term training can make operators complete production independently 4.Unique arithmetic on temperature control makes oven heating fast, temperature control precise. Which improve quality of products, reduce energy consumption and shorten the preparing time effectively. 5.Roving chopper speed can be synchronous with the production line. 6.Special cross cutting machine and good synchronization performance make cutting accurately. 7.All the machine parts adopt international standard steel make machine with high stability 8.System failure can be automatically alarmed and show fault point. Make maintenance easily 9.Particular parts adopt special purpose wire, durable in use 10.Size and layout of machine can be made according to customer requirements Basic parameter Operation staff: 4-7 people Production speed: 2-10m/min Sheet width: maximum effective width of flat sheet is 1500mm Wave height: maximum 130mm Sheet thickness: 0.4-4.0mm Gel coat thickness: 0.2-0.4mm Machine main dimension: upper gel coat:54m*4m*5m Lower gel coat:60m*1.85m*3.5m Power requirement: 100kva Power consumption: actual power consumption is about 35kw/h
1, special gutter shape cutting technology, the cutting track can be set based on customer requirement. Cutting with less noise&dust, the cutting surface is clean & tidy. 2, impregnation platform multi-line independent temperature control, temperature control is precise, able to better adapt change of ambient temperature, quick impregnation, speed of production could be improved effectively; 3, pulse free metering system, accurate metering & wide flow rate adjustment range. It can add powder filler. 4, intellectualized control system based on plc, double-computer operation. Setting of production task and parameters of equipment running is more fast and visual, degree of automation is high, production operation personnel are able to complete the production by short-term training. 5, three separate ovens for temperature control designed by dnuo, unique temperature control arithmetic, make oven heating fast, temperature control precise. Which improve quality of products, reduce energy consumption and shorten the preparing time effectively. This way makes sheets curing better.(patent number: zl 2014 2 07 31923.X) 6, metering control system and roving chopper speed can be synchronous with the production line. 7, all the machine parts adopt international standard steel make machine with high stability. 8, system failure can be automatically alarmed and show fault point. Make maintenance easily. 9, particular parts adopt special purpose wire, durable in use. 10, size and layout of machine can be made according to customer requirement 11, electric system adopt siemens brand. Operation staff: 4-9 people production speed:2-12m/min Sheet width: maximum effective width 1500mm wave height: maximum 130mm Gutter specification: standard height below 380mm, we can design based on customer requirement. Sheet thickness: 0.4mm-4mm gel coat coating thickness:0.2-0.4mm Machine main dimension: 64m(l)¡¨¢4m(w)¡¨¢5m(h) Power requirement: 150kva
Self-sealing sterilization pouch Properties: Medical Materials & Accessories Material: Medical paper (60g-70gsm) + PE/PET composite film (blue/green/white) Surface printing: Flexography Sterilization Method: STEAM and EO Feature: With a medical adhesive tape in one side and can be sealed firmly rapidly without professional sealing machine Advantage: 1. As a manufacturer, good quality and competitive price can be assured. 2. Free samples and fast delivery time 3. OEM is available by carton
Machine characterics 1.Apply high precision import forging doctor blade, small error, thin&even gel coat coating. 2.Special gutter shape cutting technology, the cutting track can be set based on customer requirment. Cutting with less noise& wide flow rate adjustment range. It can add powder filler. 3.Impregnation platform multi-line independent temperature control, temperature control is precise, anle to better adapt change of ambient temperature, quick impregnation, speed of production could be improved effectively. 4.Pulse free metering systerm, accurate metering &wide flow rate adjustment range. It can add powder filler 5.Easy operation based on plc intellectual control system. Operate by two computers, the production task and equipment operating data is faster and intuitional. Only short-term training can make operators complete production independently. 6.Three separate ovens gor temperature control designed by dnuo, unique temperature control arithmetic, make oven heating fast, temperature control precise. Which improve quality of products, reduce energy consumption and shorten. Which improve quality of products, reduce energy consumption and shorten the preparing time effectively. This way makes sheets curing better. Operation staff: 4-7 people Production speed:2-10m/ min Sheet width:maximum effective width 1500mm Wave height: maximum 130mm Gutter specification: standard height below 380mm, we can design based on customer requirement Sheet thickness:0.4-4.0mm Machine main dimension:64m*1.85m*3.5m Power requirment:130kva Power consumption: actual power consumption is 45 kw/h
