Used Oil Vacuum Distillation Machine can treat a variety of waste lube oil, to get high quality base oil and a small amount of gasoline and diesel through vacuum distillation. After pretreatment, waste oil pumping into the distillation kettle, and heating to working temperature, we will can get the base oil, gasoline and diesel .When reaction completed, stop heating, remove residue from the bottom of the tank, then the machine can be used again. The production is economical, however, the base oil is excellent .This is the most advanced technology in the world in the waste oil recycling field, and it is suitable for large-scale industrial production. systems of used engine oil recycling machine 1 Pretreatment systemWaste oil will be pumped into the distillation kettle after pretreated. 2 Distillation system: through burning gas , fuel oil or coal to make the oil in the kettle up to the working temperature. This system equipped with stirring system and insulation system. 3 Cooling system: the gaseous hydrocarbon will be cooled into liquid base oil. Gasoline and diesel. 4 Oil storage system: the base oil, gasoline and diesel get from cooling system storage here, and then pump into the storage tank. 5 Vacuum system: meet the technology requirement. 6 Filtration system: rapidly filter out mechanical impurities in the base oil, gasoline and diesel, get the high quality base oil, gasoline and diesel. Recovery rate Base oil: 85%~88 %( index same as SN150~SN200) Gasoline: about 3% Diesel: about 3%-4% Oil residue: 6%~8%
used engine oil recycling machine can treat a variety of waste lube oil, to get high quality base oil and a small amount of gasoline and diesel through vacuum distillation. After pretreatment, waste oil pumping into the distillation kettle, and heating to working temperature, we will can get the base oil, gasoline and diesel .When reaction completed, stop heating, remove residue from the bottom of the tank, then the machine can be used again. The production is economical, however, the base oil is excellent .This is the most advanced technology in the world in the waste oil recycling field, and it is suitable for large-scale industrial production. systems of used engine oil recycling machine 1 Pretreatment systemWaste oil will be pumped into the distillation kettle after pretreated. 2 Distillation system: through burning gas , fuel oil or coal to make the oil in the kettle up to the working temperature. This system equipped with stirring system and insulation system. 3 Cooling system: the gaseous hydrocarbon will be cooled into liquid base oil. Gasoline and diesel. 4 Oil storage system: the base oil, gasoline and diesel get from cooling system storage here, and then pump into the storage tank. 5 Vacuum system: meet the technology requirement. 6 Filtration system: rapidly filter out mechanical impurities in the base oil, gasoline and diesel, get the high quality base oil, gasoline and diesel. Recovery rate Base oil: 85%~88 %( index same as SN150~SN200) Gasoline: about 3% Diesel: about 3%-4% Oil residue: 6%~8%
waste engine oil recycling plant to diesel fuel can be used in black engine oil, crude oil,plastic oil and shale oil, to get gasoline and diesel oil through distilled catalyst. Pumping into the heater with raw material , through the gas,fuel oil or coal heating to working temperature, the maximum working temperature about 410 degree and the required gasoline and diesel oil can be obtained after catalytic distillation. When the reaction of raw material in reactor is complete, stop heating, and remove residue from the tank of bottom, then this machine can be used again. Systems of waste engine oil recycling plant to diesel fuel Reaction tank: raw material will be pumped into this tank from the primary filter . Heating system: by burning fuel oil ,gas or coal to make the oil temperature up to setting value. This system equips with insulation system. Catalytic system: raw material reaches the predetermined temperature, via catalytic effect, and then the gaseous hydrocarbons will become gasoline and diesel composition. Cooling system: gasoline and diesel after catalytic effect can be condensed into liquid materials. Temperature control system: ensure that raw material transform into gasoline and diesel oil, raw material drying by distillation, can stop heating timely. Exhaust gas handling system: a small amount of not liquefied gas via treated, can meet emission standards. 3.Index of oil after treatment: Yield diesel oil : 86-88%, gasoline oil: 5-6%, oil residue: 6-8%. Low-speed diesel engine can be used directly.
overview Black Waste Oil Recycle Plant through vacuum distillation to get base oil can treat a variety of waste lube oil, to get high quality base oil and a small amount of gasoline and diesel through vacuum distillation. After pretreatment, waste oil pumping into the distillation kettle, and heating to working temperature, we will can get the base oil, gasoline and diesel .When reaction completed, stop heating, remove residue from the bottom of the tank, then the machine can be used again. The production is economical, however, the base oil is excellent .This is the most advanced technology in the world in the waste oil recycling field, and it is suitable for large-scale industrial production. Systems of Black Waste Oil Recycle Plant through vacuum distillation to get base oil 1 Pretreatment systemWaste oil will be pumped into the distillation kettle after pretreated. 2 Distillation system: through burning gas , fuel oil or coal to make the oil in the kettle up to the working temperature. This system equipped with stirring system and insulation system. 3 Cooling system: the gaseous hydrocarbon will be cooled into liquid base oil. Gasoline and diesel. 4 Oil storage system: the base oil, gasoline and diesel get from cooling system storage here, and then pump into the storage tank. 5 Vacuum system: meet the technology requirement. 6 Filtration system: rapidly filter out mechanical impurities in the base oil, gasoline and diesel, get the high quality base oil, gasoline and diesel. Recovery rate Base oil: 85%~88 %( index same as SN150~SN200) Gasoline: about 3% Diesel: about 3%-4% Oil residue: 6%~8%
Overview black motor oil recycle to diesel fuel machine can be used in black engine oil, crude oil,plastic oil and shale oil, to get gasoline and diesel oil through distilled catalyst. Pumping into the heater with raw material , through the gas,fuel oil or coal heating to working temperature, the maximum working temperature about 410 degree and the required gasoline and diesel oil can be obtained after catalytic distillation. When the reaction of raw material in reactor is complete, stop heating, and remove residue from the tank of bottom, then this machine can be used again. Systems of black motor oil recycle to diesel fuel machine Reaction tank: raw material will be pumped into this tank from the primary filter . Heating system: by burning fuel oil ,gas or coal to make the oil temperature up to setting value. This system equips with insulation system. Catalytic system: raw material reaches the predetermined temperature, via catalytic effect, and then the gaseous hydrocarbons will become gasoline and diesel composition. Cooling system: gasoline and diesel after catalytic effect can be condensed into liquid materials. Temperature control system: ensure that raw material transform into gasoline and diesel oil, raw material drying by distillation, can stop heating timely. Exhaust gas handling system: a small amount of not liquefied gas via treated, can meet emission standards. 3.Index of oil after treatment: Yield diesel oil : 86-88%, gasoline oil: 5-6%, oil residue: 6-8%. Low-speed diesel engine can be used directly.
TZL waste steam turbine oil filter machine Solely Designed for Turbine Oil is case-hardened product of electric power industry. This machine adopts the latest techniques that integrate gravity, sedimentation, agglomeration, vacuum separation, adsorption, separation, and pressure filtration. It has super ability of demulsification, dehydration, degasification, and removing impurity, so it is the ideal equipment for disposing wheel oil, low viscidity lubricant, and hydraulic pressure. ---It is widely used in electric power, metallurgy, etc. for purifying turbo oil of steam turbine, water turbine, fuel machine and steam turbine group. It can demulsify, dehydrate and purify water-mixed, serious emulsified turbo oil, and low viscidity lubricant. It can be also used in other mechanical equipment. Technical Parameters Model Unit TZL-20 TZL-30 TZL-50 TZL-70 TZL-100 TZL-150 TZL-200 Rated Flow L/min 20 30 50 70 100 150 200 Vacuum Range Mpa -0.07~-0.099 Temperature Range 40~80 Oil pump pressure Mpa 0.4 Total Power kw 28 32 42 56 68 89 130 Acid value mgKOH/g 0.1 Working Noise db(A) 65 85 Cleanliness NAS1638 NAS 6 Demulsifying value min 15 Water content in oil PPM 40 Mechanical impurity % No inlet(outlet)diameter mm 25 25 32 32 42 50 60 Dimension(mm) L 1400 1400 1450 1500 1550 1550 1600 W 920 950 900 940 1000 1200 1300 H 1420 1500 1600 1650 1700 1500 1820 Dimension and weight will be changed with changing the technical specification.
overview Black Waste Oil Purification Machine to SN300 can treat a variety of waste lube oil, to get high quality base oil and a small amount of gasoline and diesel through vacuum distillation. After pretreatment, waste oil pumping into the distillation kettle, and heating to working temperature, we will can get the base oil, gasoline and diesel .When reaction completed, stop heating, remove residue from the bottom of the tank, then the machine can be used again. The production is economical, however, the base oil is excellent .This is the most advanced technology in the world in the waste oil recycling field, and it is suitable for large-scale industrial production. Systems of Black Waste Oil Purification Machine 1 Pretreatment systemWaste oil will be pumped into the distillation kettle after pretreated. 2 Distillation system: through burning gas , fuel oil or coal to make the oil in the kettle up to the working temperature. This system equipped with stirring system and insulation system. 3 Cooling system: the gaseous hydrocarbon will be cooled into liquid base oil. Gasoline and diesel. 4 Oil storage system: the base oil, gasoline and diesel get from cooling system storage here, and then pump into the storage tank. 5 Vacuum system: meet the technology requirement. 6 Filtration system: rapidly filter out mechanical impurities in the base oil, gasoline and diesel, get the high quality base oil, gasoline and diesel. Recovery rate Base oil: 85%~88 %( index same as SN150~SN200) Gasoline: about 3% Diesel: about 3%-4% Oil residue: 6%~8%
Waste Oil Purifier Machine\ Oil Purification System can treat a variety of waste lube oil, to get high quality base oil and a small amount of gasoline and diesel through vacuum distillation. After pretreatment, waste oil pumping into the distillation kettle, and heating to working temperature, we will can get the base oil, gasoline and diesel .When reaction completed, stop heating, remove residue from the bottom of the tank, then the machine can be used again. The production is economical, however, the base oil is excellent .This is the most advanced technology in the world in the waste oil recycling field, and it is suitable for large-scale industrial production. Systems of equipment 1 Pretreatment systemï¼?Waste oil will be pumped into the distillation kettle after pretreated. 2 Distillation system: through burning gas , fuel oil or coal to make the oil in the kettle up to the working temperature. This system equipped with stirring system and insulation system. 3 Cooling system: the gaseous hydrocarbon will be cooled into liquid base oil. Gasoline and diesel. 4 Oil storage system: the base oil, gasoline and diesel get from cooling system storage here, and then pump into the storage tank. 5 Vacuum system: meet the technology requirement. 6 Filtration system: rapidly filter out mechanical impurities in the base oil, gasoline and diesel, get the high quality base oil, gasoline and diesel. Recovery rate Base oil: 85%~88 %( index same as SN150~SN200) Gasoline: about 3% Diesel: about 3%-4% Oil residue: 6%~8%
ZLA series double stage vacuum oil purifier is manufactured according to standards, which go beyond Chinese legal criterion, dealing with almost insulation oil of power equipment more rapidly and effectively with the supporting of high vacuum and speed absorption. Thus the strength of insulation oil is much increased and shorten the dealing time. Features 1) Manufactured as per standards which go beyond the legal criterion.A primary breakdown voltage can raise 35KV and reduces the oil damage causing by normal purifiers due to repeated heating. 2) Large absorption speed double vacuum meets the needs of vacuum zing of transformer on an installation or repair site, at the same time remove the water,gas,and also keep the completeness of transformer oil.It significantly shortens the oil treatment time. 3) The unique gas, water removal system adopting stereo-evaporation technology, which rapidly separates the water and gas in the oil and is free of maintenance. 4) A superior purification system with top quality filter core, which can accommodate large quantity of impurities and is progressively dandified step by step. It has been got a high precision and multi-stage filtration. 5) Imported parts adopt all electric system, which ensures high performance. 6) Advanced infrared liquid level control system with automatic control, allowing separated operation of manual operators from a machine. 7) Interlocked safety protection device. i.e,backflow of A oil outlet over pressure can be achieved via an overflow valve, B oil inlet will interlock with heating system which avoids any possible negative impacts caused by mal-operation 8) Precision oil pumps have low noise and environmental regulatory compliance will be well met . Technical Parameters Model Unit ZLA-30 ZLA-50 ZLA-70 ZLA-100 ZLA-150 ZLA-200 ZLA-250 Rated flow L/min 30 50 70 100 150 200 250 Vacuum Range Mpa -0.05~-0.099 Temperature Range 40~80 Oil pump pressure Mpa 0.05~0.3 Total Power kw 38 46 62 90 120 144 175 Power 50HZ 380V Working Noise db(A) 65 85 Cleanliness NAS1638 NAS 6 Breakdown Voltage kv 75 Water content PPM 3 Gas content in oil % 0.05 Filter precision µm 3 Inlet (outlet) diameter 25 32 32 42 50 60 60 Dimensionï mmï L 1480 1670 1820 2000 2100 2300 2300 W 980 1150 1300 1500 1600 1800 1800 H 950 1000 1200 1300 1600 1600 1600 Dimension and weight will be changed with changing the technical specification.
ZLA series Waste transformer oil filtration machine is manufactured according to standards, which go beyond Chinese legal criterion, dealing with almost insulation oil of power equipment more rapidly and effectively with the supporting of high vacuum and speed absorption. Thus the strength of insulation oil is much increased and shorten the dealing time. Features 1) Manufactured as per standards which go beyond the legal criterion.A primary breakdown voltage can raise 35KV and reduces the oil damage causing by normal purifiers due to repeated heating. 2) Large absorption speed double vacuum meets the needs of vacuum zing of transformer on an installation or repair site, at the same time remove the water,gas,and also keep the completeness of transformer oil.It significantly shortens the oil treatment time. 3) The unique gas, water removal system adopting stereo-evaporation technology, which rapidly separates the water and gas in the oil and is free of maintenance. 4) A superior purification system with top quality filter core, which can accommodate large quantity of impurities and is progressively dandified step by step. It has been got a high precision and multi-stage filtration. 5) Imported parts adopt all electric system, which ensures high performance. 6) Advanced infrared liquid level control system with automatic control, allowing separated operation of manual operators from a machine. 7) Interlocked safety protection device. i.e,backflow of A oil outlet over pressure can be achieved via an overflow valve, B oil inlet will interlock with heating system which avoids any possible negative impacts caused by mal-operation 8) Precision oil pumps have low noise and environmental regulatory compliance will be well met . Technical Parameters Model Unit ZLA-30 ZLA-50 ZLA-70 ZLA-100 ZLA-150 ZLA-200 ZLA-250 Rated flow L/min 30 50 70 100 150 200 250 Vacuum Range Mpa -0.05~-0.099 Temperature Range 40~80 Oil pump pressure Mpa 0.05~0.3 Total Power kw 38 46 62 90 120 144 175 Power 50HZ 380V Working Noise db(A) 65 85 Cleanliness NAS1638 NAS 6 Breakdown Voltage kv 75 Water content PPM 3 Gas content in oil % 0.05 Filter precision µm 3 Inlet (outlet) diameter 25 32 32 42 50 60 60 Dimension mm L 1480 1670 1820 2000 2100 2300 2300 W 980 1150 1300 1500 1600 1800 1800 H 950 1000 1200 1300 1600 1600 1600 Dimension and weight will be changed with changing the technical specification.
ZLA series Switch oil transformer oil processing system is manufactured according to standards, which go beyond Chinese legal criterion, dealing with almost insulation oil of power equipment more rapidly and effectively with the supporting of high vacuum and speed absorption. Thus the strength of insulation oil is much increased and shorten the dealing time. Features 1) Manufactured as per standards which go beyond the legal criterion.A primary breakdown voltage can raise 35KV and reduces the oil damage causing by normal purifiers due to repeated heating. 2) Large absorption speed double vacuum meets the needs of vacuum zing of transformer on an installation or repair site, at the same time remove the water,gas,and also keep the completeness of transformer oil.It significantly shortens the oil treatment time. 3) The unique gas, water removal system adopting stereo-evaporation technology, which rapidly separates the water and gas in the oil and is free of maintenance. 4) A superior purification system with top quality filter core, which can accommodate large quantity of impurities and is progressively dandified step by step. It has been got a high precision and multi-stage filtration. 5) Imported parts adopt all electric system, which ensures high performance. 6) Advanced infrared liquid level control system with automatic control, allowing separated operation of manual operators from a machine. 7) Interlocked safety protection device. i.e,backflow of A oil outlet over pressure can be achieved via an overflow valve, B oil inlet will interlock with heating system which avoids any possible negative impacts caused by mal-operation 8) Precision oil pumps have low noise and environmental regulatory compliance will be well met . Technical Parameters Model Unit ZLA-30 ZLA-50 ZLA-70 ZLA-100 ZLA-150 ZLA-200 ZLA-250 Rated flow L/min 30 50 70 100 150 200 250 Vacuum Range Mpa -0.05~-0.099 Temperature Range 40~80 Oil pump pressure Mpa 0.05~0.3 Total Power kw 38 46 62 90 120 144 175 Power 50HZ 380V Working Noise db(A) 65 85 Cleanliness NAS1638 NAS 6 Breakdown Voltage kv 75 Water content PPM 3 Gas content in oil % 0.05 Filter precision µm 3 Inlet (outlet) diameter 25 32 32 42 50 60 60 Dimension mm L 1480 1670 1820 2000 2100 2300 2300 W 980 1150 1300 1500 1600 1800 1800 H 950 1000 1200 1300 1600 1600 1600 Dimension and weight will be changed with changing the technical specification.
ZLA series vacuum transformer oil treatment machine is manufactured according to standards, which go beyond Chinese legal criterion, dealing with almost insulation oil of power equipment more rapidly and effectively with the supporting of high vacuum and speed absorption. Thus the strength of insulation oil is much increased and shorten the dealing time. Features 1) Manufactured as per standards which go beyond the legal criterion.A primary breakdown voltage can raise 35KV and reduces the oil damage causing by normal purifiers due to repeated heating. 2) Large absorption speed double vacuum meets the needs of vacuum zing of transformer on an installation or repair site, at the same time remove the water,gas,and also keep the completeness of transformer oil.It significantly shortens the oil treatment time. 3) The unique gas, water removal system adopting stereo-evaporation technology, which rapidly separates the water and gas in the oil and is free of maintenance. 4) A superior purification system with top quality filter core, which can accommodate large quantity of impurities and is progressively dandified step by step. It has been got a high precision and multi-stage filtration. 5) Imported parts adopt all electric system, which ensures high performance. 6) Advanced infrared liquid level control system with automatic control, allowing separated operation of manual operators from a machine. 7) Interlocked safety protection device. i.e,backflow of A oil outlet over pressure can be achieved via an overflow valve, B oil inlet will interlock with heating system which avoids any possible negative impacts caused by mal-operation 8) Precision oil pumps have low noise and environmental regulatory compliance will be well met . Technical Parameters Model Unit ZLA-30 ZLA-50 ZLA-70 ZLA-100 ZLA-150 ZLA-200 ZLA-250 Rated flow L/min 30 50 70 100 150 200 250 Vacuum Range Mpa -0.05~-0.099 Temperature Range ?? 40~80 Oil pump pressure Mpa 0.05~0.3 Total Power kw 38 46 62 90 120 144 175 Power 50HZ 380V Working Noise db(A) 65 85 Cleanliness NAS1638 NAS 6 Breakdown Voltage kv 75 Water content PPM 3 Gas content in oil % 0.05 Filter precision µm 3 Inlet (outlet) diameter 25 32 32 42 50 60 60 Dimension mm L 1480 1670 1820 2000 2100 2300 2300 W 980 1150 1300 1500 1600 1800 1800 H 950 1000 1200 1300 1600 1600 1600 Dimension and weight will be changed with changing the technical specification.
ZL series of Single-stage Transformer Oil Treatment Equipment is case-hardened product of electric power industry. It is researched according to the newest drying theory and precisely filtering technology for disposing unqualified insulation oil of electric department and other enterprises. It is an ideal equipment used in drying and making vacuum oil injection. ---Usage: It is widely used in power plant, hydropower station, electric power company, metallurgy, petrifaction, railroad, etc. It can purify unqualified transformer oil, mutual-inductor oil, switch oil and capacitor oil, also rapidly dehydrate, degasify and purify oil. Meanwhile, it also has the function of drying electric machine and injecting oil to electric equipment. ---Characteristics: A: Super dehydration and degasification system. We adopt large cubage to rapidly separate water and gas from oil. B: Reliable heating system to ensure heating and stable oil temperature. C: Precise filtration system adopts high-grade filtration materials which has advantages of good mechanical intensity, multi-level filtration, gradually intensive and high filtration precision system. D: Advanced pressure protection device and infrared control system can avoid the influence of wrong operation. E: Integration has chain security protection. It can automatically control the oil pressure and oil level. F: This machine can be used with BZ series of transformer oil discoloring device together to add the function of acid-removing, discoloring, uncombined carbon removing, and reducing damage. Technical Parameters Model ZL-20 ZL-30 ZL-50 ZL-70 ZL-100 ZL-150 ZL-200 Rated Flow L/min 20 30 50 70 100 150 200 Vacuum Range -0.05 -0.099Mpa Temperature Range 60¬ 80 Degree centigrade Oil pump pressure 0.05-0.3Mpa Total Power kw 25 25 32 32 42 50 60 Breakdown Voltage 54kv Power 50HZ 380V Working Noise 65 80 db(A) Cleanliness NAS 6 NAS1638 Water content in oil 5ppm Gas content in oil 0.1% Filter precision 5um Inlet (outlet) diameter mm 33 33 48 48 60 60 60 Dimension mm L 1100 1100 1200 1250 1300 1400 1550 W 700 700 800 850 900 1000 1200 H 1300 1350 1400 1450 1520 1600 1800 Attention:Dimension and weight will be changed with changing the technical specification.
LY series plate pressure oil purifier is mainly used to separate the impuritys and water from the oil. It is suitable for filtering the cooking oil, transformer oil, used lubricating oil and so on. There is filtering media, such as filtering paper or filtering cloth, installed between the plastic filter board and filter plate that will be fixed to form a single filtering room under the pressure of the packing device. The filtering paper or filtering fuse packed between the filter board and filter plate will play a role of filtering. It's characterized by simple structure,easy operation,low cost,etc. Technical Parameters Type LY-30 LY-50 LY-100 LY-125 LY-150 LY-200 LY-300 Rated Flow L/min 30 50 100 125 150 200 300 Working Pressure MPa 0 0.5 Filtering area ¡ 0.8 1.1 1.5 1.8 2.0 2.5 3.1 Plate Size mm 280 280 Compaction Method Manual screw clamping Number of Filtering Frame 11 13 17 23 25 34 41 Number of Filtering Plate 12 14 18 25 26 35 42 Power 380V 50HZ Power of Motor(KW) 1.1 1 5 2 2 2 2 3 4 5 5 Rotating Speed r/min 1440 Filter Precision m 5 Size of Filtering Cloth mm 300 300 Oil Inlet (outlet ) Diameter mm 32 32 42 42 50 50 60 Apparent Size mm Length 700 800 850 850 950 1200 1400 Width 410 530 530 600 600 600 600 Height 800 930 930 1100 1100 1100 1100 Total Weight kg 80 95 130 190 210 250 300 Attention:Dimension and weight will be changed with changing the technical specification.
Usage: JL is fit for oil-using departments and corollary equipments. It can be used in the filtration of mechanical impurity, high-lift and long-distance oil pumping and injection. Suits all kinds of oils. Characteristics: ---This type of machine filters by three steps whose filtering elements gradually become intensive. It doesnt need filter paper with several advantages such as: portable, easy-handling and environment protection .etc. It can not only filter the impurities in oil, but also satisfy the high-lift and long-distance oil pumping and injection. Technical Parameters Model JL-30 JL-50 JL-70 JL-100 JL-150 JL-200 JL-250 JL-300 Flow L/min 30 50 70 100 150 200 250 300 Lift 5m 8m 8m 10m 12m 15m 15m 15m Filter precision 5 µm 5 µm 5 µm 5 µm 5 µm 5 µm 5 µm 5 µm Total Power (kw) 0.55 0.75 1.1 2.2 3 3 4 4 Power 3PH 50HZ 380V inlet (outlet) diameter Made according to the custor demand mm Dimension L 560 650 650 1200 1200 1250 1250 1250 W 450 500 500 450 450 580 580 580 H 450 500 500 1050 1050 1150 1150 1150 Weight KG 22 31 42 51 72 91 112 135 Attention: Dimension and weight will be changed with changing the technical specification.
It currently adopts the most advanced principles of Coalescence-separation in world, collecting filtration precision and efficient demulsification and dehydration in one, can remove a large amount water without heating the oil, can fast separate water from the oil that has the equal amount of oil and water, and after treatment the cleanliness level up to NAS6, the water content in oil up to 50ppm, it is not easy to rust when use the oil after filtration to clean the bearings, lower costs, the oil can be reused, compact design, simple and easy to operate. Basically it is non-wearing for parts, low maintenance costs, small energy consumption, and the trolley-style design is convenient for the movement of equipment. Working Principle Coalescence separator is equipped with two different functions of the filters inside - separation filter and coalescence filter. the medium for dehydration go through the import of coalescence separator into the filter shell, and the filter tray distribute it to of each coalescence filter, liquid flows from inside to outside of coalescence filter, after filtration, emulsion breaking, coalescence, and sedimentation four process, the liquid demulsify the emulsion, and then after demulsification the droplet water form the large big one and subside at the bottom of the shell. Part of the droplet water with the liquid flow into separation filter, the filter is made up of a special filter material with good water-repellent performance, small drops were completely and effectively blocked outside of the filter, and form bog drops again to subside, so as to ensure effective removal of water. The water subside at the bottom of the shell can be shown by the lever meter, so that the water and dirt can be removed out by the drainage valve from time to time. The media after separated water will be collected by separation filter tray, and flow out from export of the separator. Technical parameters Items Unit TLA-10 TLA-20 TLA-30 TLA-50 TLA-70 TLA-100 TLA-200 Flow L/min 10 20 30 50 70 100 200 Working pressure Mpa 0.3 Water content in oil PPM 50 CLeanliness NAS 6级 Working noise dB(A) 55 65 85 Power KW 0.75 0.75 0.75 2.2 2.2 3 6 Dimension mm 700 700 700 800 800 1000 1500 570 570 600 650 650 700 1000 550 600 650 750 800 850 1200 Weight KG 100 110 130 150 160 190 260 Dimension and weight will be changed with changing the technical specification.
It is widely applied to phosphate ester fire-resistant oil system and mechanical equipment (oil filter machine). Features: 1)The purifier is a next-generation vacuum oil filter machine destined for phosphate ester fire-resistant oil system, utilizing dewatering and degassing technologies such as anti-precipitation, aggregation, separation, transformation, resolution, vacuum entrapment and flash evaporation, which not only speedily removes the free water in oil but also intensively removes the dissolved water and gas in oil. 2)The stage-to-stage dandified filter element made of new composite materials can remove the large amount of impurities in oil and reach the purpose of precision filtration. 3)Application of new absorptive materials can effectively absorb the jelly substance in oil, eliminate the acid content in oil,and inhibit the production of new acid in the system. 4)The purifier body is made of anti-acid,anti-dissolving and stainless steel.The filter elements and seals are made of fire-resistant oil materials.. Technical Parameters Model KL-10 KL-20 KL-30 KL-50 KL-70 Rated Flow(L/min) 10 20 30 50 70 Vacuum Range -0.05 -0.099Mpa Temperature Range 40 65 Oil pump pressure 0.05 0.3Mpa Power Supply 50HZ 380V Total Power 20 kw 27 5 kw 35 kw 49 kw 65 kw Working Noise 80 db(A) Gas content in oil 0.1 % mgkoH/g Water content in oil 400ppm Cleanliness NAS 6 Mechanical impurity no Dimension(mm) 600 480 850 700 480 900 800 480 950 900 500 1000 950 500 1000 Attention: Dimension and weight will be changed with changing the technical specification.
Waste Oil Refinery Machine can be used in black engine oil, crude oil,plastic oil and shale oil, to get gasoline and diesel oil through distilled catalyst. Pumping into the heater with raw material , through the gas,fuel oil or coal heating to working temperature, the maximum working temperature about 410 degree and the required gasoline and diesel oil can be obtained after catalytic distillation. When the reaction of raw material in reactor is complete, stop heating, and remove residue from the tank of bottom, then this machine can be used again. Systems of equipment Reaction tank: raw material will be pumped into this tank from the primary filter . Heating system: by burning fuel oil ,gas or coal to make the oil temperature up to setting value. This system equips with insulation system. Catalytic system: raw material reaches the predetermined temperature, via catalytic effect, and then the gaseous hydrocarbons will become gasoline and diesel composition. Cooling system: gasoline and diesel after catalytic effect can be condensed into liquid materials. Temperature control system: ensure that raw material transform into gasoline and diesel oil, raw material drying by distillation, can stop heating timely. Exhaust gas handling system: a small amount of not liquefied gas via treated, can meet emission standards. 3.Index of oil after treatment: Yield diesel oil : 86-88%, gasoline oil: 5-6%, oil residue: 6-8%. Low-speed diesel engine can be used directly.
Motor Engine Oil Regeneration Unit can treat a variety of waste lube oil, to get high quality base oil and a small amount of gasoline and diesel through vacuum distillation. After pretreatment, waste oil pumping into the distillation kettle, and heating to working temperature, we will can get the base oil, gasoline and diesel .When reaction completed, stop heating, remove residue from the bottom of the tank, then the machine can be used again. The production is economical, however, the base oil is excellent .This is the most advanced technology in the world in the waste oil recycling field, and it is suitable for large-scale industrial production. Recovery rate Base oil: 85%~88 %( index same as SN150~SN200) Gasoline: about 3% Diesel: about 3%-4% Oil residue: 6%~8%
pe coated paper, paper laminated with foil, wrapping and grease proof paper, paper bags, perforated and plain paper for garment industry, plotter paper, adhesive paper.
