Isolation Gowns X Large Aami Level 2 Suppliers and Manufacturers

ITO GLOBAL, SURAT, GUJARAT ( India ) We can supply high strength, quality tested and recyclable fresh PP bags of size 29x43 inch , for filling grains (like wheat) up to 25-50-100 kgs with UV protection, BAGS Weight- as per customers requirements. as a replacement for costly Jute Bags, in packaging of 500 bags/bale with compressed packaging to save logistics costs. Size can be customized as per requirement. Also, available in transparent, milky white and colors. Bag Specification 1. Bag Size 29 x 43 inch ( 74 cm x 110 cm) 2. Bag weight 155 grams / PC (2% tolerance) 3. Mesh 11 x 11 4. UV rays protection 5. Flexible bag 6. Packaged in moisture proof and compressed bales of 500 Bag Pieces / bale 7. Estimated rates as mentioned. 8. Rates are for FOB, CIF, CFR Basis, Hazira, India. We can supply across any major port on CIF basis. 9. Samples are available.

* PHOSCAST Phoscast : Phosphate Bonded Castables * PURPOSE customers using FBC boilers (Particularly underbed feed FBC boilers) for the protection of inbed coils against erosion potential by applying highly abrasive resistant refractory on inbed coils above fuel feed system. BACKGROUND * Two of such actions are providing special alloy studs on inbed coils and applying highly abrasive resistant refractory on the outer bottom loops of inbed Coils which are above the fuel feed nozzles. * GANESHAS has taken number of approaches to identify the key factors affecting erosion rates with an objective to enhance the life of inbed tubes as well as implementing the corrective action to reduce the erosion rates. Phosphate coatings are often used to protect steel parts against rusting and other types of corrosion * Erosion of inbed coils in fluid bed combustor is unavoidable phenomenon however the rate of metal wastage and thus the life of tubes depends on various factors like ash & fuel properties, design of Combustor / feeding system, flue gas velocities operating conditions etc. It has been also observed that maximum erosion prone inbed coils are those which come above fuel feed nozzles and an area of approximately 1 to 1.5 mts around fuel feed systems are badly affected. APPLICATION Phoscast-90 XR can be applied by ramming with wooden mallet having adequately large head @" dia x 5" length x 10â?? Jong handle). The desired lining or repair thickness is built up in several courses while ramming the mass to uniform thickness. Phoscast refractory should never be trawled to obtain smooth surface; ramming only should finish surface. Any excess mass is to be sliced off with trowel edge and then finished by ramming again for bed coil. Tube application of AFBC boiler, the material pasty mass should be finger pressed into the studs of the tube with maximum force. Finish should be given by pressing the hand palm against material applied, using surgical type thin rubber hand gloves.

The importance of white maize or Corn is due to its wide diversity of uses. It is used both as food for human and feed for animals. White Maize has its significance as a source of a large number of industrial products besides its uses as human food and animal feed. It is used in various forms such as - corn meal, cornflakes, popcorns, corn flour, baby corns, corn cooking oil etc. It is also a major source of starch, and a major ingredient in home cooking. The starch, the major constituent of the corn kernel, is used in its native form or after chemical or enzymatic modification, in foods and industrial products. The starch is also converted into glucose or fructose for use as food sweetness. Glucose can be fermented in to ethanol for fuel or beverages or into many other chemicals. Specifications:- Moisture: 12% �?�¢?? 14% max Foreign Matter: 2% max Broken: 2.5% max Damaged Kernels: 5% max Admixture: 2% max Shriveled /Immature grains: 2.5% to 4.5% max Weevilled grains:1% max

PRE ORDER / PRODUCTION FOB Thailand ( Laem Chabang Port ) KC 500; Nitrile Examination Gloves MOQ: 5 Million x 12 months MAX: 20M x 12 months Price USD8.00 KimTech; Nitrile Examination Gloves MOQ: 5 Million x 12 months MAX: 20M x 12 months Price USD8.20 *Including USD0.10 commission for buyer side *Sea Freight USD0.35 - USD0.50 CIF Payment terms : 1. SBLC as Warranty, amounting Half Value of First Month Delivery and or 2. Irrevocable Revolving Non Transferable Divisible LC with withdrawal % from the LC as deposit from the total amount of 1 month. Standing Operative Procedure; 1. NCNDA via Docusign 2. Buyer issues LOI, ICPO, LOA (if Proxy) and Proof Of Fund (*via Ready Willing Able or RWA Letter from the Buyer's Bank) for Fund verification, KYC 3. Within 24 to 48 hours of receiving the above Documents after verification, Buyer will be provided with a Draft Sales Purchase Agreement and LC Draft 4. Once the Buyer has reviewed the SPA, the Buyer and Seller will sign SPA - IMFPA. 5. Allocation Letter @ Authorization Letter will be provided thru the Zoom Meeting 6. Seller provides PI 7. Within 3 working days after the contract assigned, Buyer activate Letter of Credit @ Irrevocable Revolving Non Transferable Divisible LC to Seller with the following terms As Note given accordingly 2.5% - 10% payment withdrawn from the IRTLC for the deposit against Confirmation Letter from Factory and Invoice from Seller from the total amount of 1 month 90% - 97.5% will be withdrawn upon completion of SGS and ready for shipment for the First Month and 100% subsequently (to be confirmed by issuing bank) or value including the full purchase price plus the 2.5% - 10% one month sales for Deposit 8. PRODUCTION START 9. Seller provide delivery schedule from Factory within 10 - 15 working days after receipt of LC. If not Seller pay penalty 2.5% of 1 Month of Sales 10. Buyer provide SGS Inspection details to Seller to get approval from Factory for the Inspection 11. SGS is completed at the factory warehouse and after receive full payment the goods release from the Warehouse. 12. Seller released original documents to Buyer : Certificate of Origin, Packing List, Pro Forma Invoice 13. The Seller is responsible for the goods until they are loaded on a shipping vessel of which point all liability, risks, insurance and costs shifted to the buyer 14. TRANSACTION COMPLETE NOTE; 1.1Mil Deposit 10% 2. 5Mil Deposit 5% - 7% 3. 10M Deposit 3% - 5% 4. 20M Deposit 2.5%

* Gentle gel type cleanser with mildly acidic pH level - While refining the skin texture, the cleanser will help cleanse with no stripping. Great for all skin types, wake up to a firmer-looking skin while letting it rest clean during the night. 1. DETAILS - BENEFITS Hydrating cleanse without stripping Removes impurities Protects skin barrier Restores pH Balance - TARGETS Dry skin Dull & tried skin Uneven skin texture * Great for sensitive skin 2. INGREDIENTS - KEY INGREDIENTS 0.5% Betaine Salicylate (BHA) & 5,000ppm Tea Tree Oil : Soothe and strengthen for luminous and clear skin pH Balanced pH 5.31+1.00 : Optimize the balance of oil and water in the skin 3. HOW TO USE Use morning and night, after removing makeup. Begin with wet hands and face. Squeeze a proper amount onto your hand and foam up. Gently massage onto face avoiding the eye and mouth area. Rinse with warm water.

Good Feeling 2D KF94 Quarantine Mask is a quality product approved by the Korean Ministry of Food and Drug Safety.  Respiratory protection from harmful particulate matter such as yellow dust, fine dust, and infectious sources  1. V-Fit thin face design With thin face visual effect. The inside does not touch the lips for a comfortable fit. 2. High-specification MB filter The Korean-made high-standard MB filter can block more than 94% of particulate harmful substances such as sandstorms, fine dust (PM2.5), and infection sources. 3. High elastic ear straps Use high elastic ear straps for comfortable wearing Mask size (unopened): 13 (w) x 14.5 (h) cm

This is chemical setting Furan based chemical resistant mortar which is combination of Liquid and Powder, when mixed in proper proportion from workable mortar which after setting and curing give of liquid and give black highly cross linked composites. Furan When set and cured is resistant to highly corrosive acids, alkalis and to powerful organic solvents such as ketones, Aromatic and Chlorinated solvents. It has extreme resistant to Acidic & alkalis, Salts, Greases and Detergents. It resists to Organic & Inorganic acids at their boiling temperature. It is suitable against mild chlorine Gas (dry) phosphorous trichloride, pyridine at room temperature. Furan is especially useful where resistance to mixed media such as aqueous acids /alkalis and organic solvents is needed in chemical plant process and waste streams. Carbon filled Furan is used against corrosive effect of hydrofluoric acid & its salts. PREPARATION OF FURANE MORTAR : Mortar consist of Furan solution and Furan powder. The average mixing ratio necessary to obtain mortar with good working consistency is 1 part by weight Solution & 3 part by weight powder. The ratio will vary slightly depending on temperature and working conditions.Stir the liquid thoroughly before using. Place liquid in a suitable shallow mixing pan. Add powder by weight in the solution mix thoroughly and rapidly until all lumps are dispersed and the mortar is completely homogenous. Spread out the mortar in a thin layer, not more than ¾ thick, to dissipate the heat of reaction and lengthen the working life. Batch size can be varied depending upon the temperature and the speed with which the masons are working. Very large batches will become stiff quite rapidly. Make sure that all the Furan Motrar is used from the pan before another batch is mixed.When working at temperature above 40 C, very small batches not more than 2 Kgs, should be prepared. When working at temperature below 15C the liquid should be kept warm.

Bitumen Primer * Bitumen Primer is Bituminous air curing ready mixed Acid & Alkali resistant special primer. Application * Concrete surface must be clean, dry and rough. No primer should be applied over smooth and wet surface. * After cleaning the concrete surface, one coat of Bitumen Primer should be applied with brush and allow to dry thoroughly. * The drying time will depend upon the temperature. * 24 Month at the temperature 30C (+2OC) Packing * Bitumen Primer: 25 Liter Drum Note * Bitumen Primer contains volatile and slightly toxic solvent. Keep away from spark and open flames at working area. * Bitumen premier it is manufactured using bitumen solution which is used for sealing of prime porous and non-porous surface, and also to protect residential and commercial building. * Bitumen Primer is used to protect substrate against corrosive attack, is suggested to apply anti-corrosive primer.It is best for protection against sub-striate against atmospheric corrosion and chemical corrosion. It is a mixed substance made up of organic liquids that are highly sticky, water proof, viscous,acid proof as with all surface coating, good Bitumen Premier is used for long life of the system. it is applied by brush or roller and allowed to dry before any water proofing treatment so to avoid solvent it is used in defects such as cracks, broken mortar joints, etc. are to be repaired prior to Bitumen primer application. Product Details: Grade Standard Technical Grade Physical State - Liquid Usage - Industrial Color - Black Characteristics: Appearance/Color - Pasty liquid/ black Chemical Base - Bituminous rubber emulsion. Density - 1.0 kg/l Curing Speed/ Rate - 3 - 4 hours Tack free after - 5 - 10 hours Cured after - 2 - 4 days (Dependent on ambient Solid Content by - temperature, substrate temperature, Weight - relative Water Content by weight - humidity and thickness of the coating) Bitumen Content - 41% by weight - Thixotropic (The viscosity can be adjusted by - Viscosity adding up to max. 5% of clean water. - Stir well prior use) - For light protection: 1.0 mm min. Coating - For greater protection: ~ 1.5 - 2.0 mm Thickness applied - in two coats. Water Penetration - 48 h, 1 bar: 78.5 cm2: 0 ml under Hydrostatic - 96 h, 4 bar: 78.5 cm2: 33 ml Pressure - Water vapor 6 x 10-7 mg / hmPa Permeability Service - -30 C to 200 C Temperature - Adhesion Concrete - Very good, Timber: Very good, Metal: Moderate Glass: Poor

Fresh meat stick dice cutting machine Small type fresh cutting machine from A large piece of meat process can cutting 2 kind shape : cutting meat stick ---cutting diced, small and exquisite,sanitary,low cost high profit ,smooth stable working,easy cleaning. (Also can cutting vegetable fruit other food ) capacity 400-1000kg/hour, about 3 cube . Peak sales season pls in advance order!

Hot eye Onion Peeling Machine Automaitc onion peeling machine with onion root cutting in-one-machine 1 The whole process of onion from feeding, peeling, peeling, root cutting, output and other processes is automated and unmanned, which can save a lot of labor costs. 2 Peel by layers, either more or less. The equipment is designed with a cortex controller, which can be peeled as required. Only one layer of skin can be peeled, or two or three layers of skin can be removed. 3 The peeling is clean and effective. The peeled scallions are clean and good in appearance. 4 The root cutting part is equipped with an onion size recognition mechanism, and the size of the cutting amount can be adjusted randomly to avoid the disadvantage of cutting large onions into small ones and small ones into large ones. 5 Small size, high yield. The equipment design strives to reduce the volume on the premise of increasing the output, so as to apply to various application scenarios such as large, medium and small enterprises and small family workshops.

Adjustable Fruit vegetable sorting machine grader machine Can be use for rond shape fruit /vegetable grader/sorting machine ,can customized . 1. The fruit and vegetable grader is suitable for grading all kinds of round and oval fruits and vegetables. The conveyor belt has a small fruit drop, and the grading process will not cause secondary damage to the fruit 2. All parts in contact with the fruit are thickened and soft wrapped, and the grading process will not damage the fruit. The grading size can be adjusted at will 3. It is made of stainless steel, with high hardness and no deformation, and the equipment is solid and durable. At the same time, it is equipped with a large fruit tray (you can choose to load on one side of the machine or on the top of the machine), which can pick out bad fruits. One machine can be used for many purposes. 4. The number and size of grading can be adjusted at will.

Fruit vegetable sorting machine grader machine 1. The fruit and vegetable grader is suitable for grading all kinds of round and oval fruits and vegetables. The conveyor belt has a small fruit drop, and the grading process will not cause secondary damage to the fruit 2. All parts in contact with the fruit are thickened and soft wrapped, and the grading process will not damage the fruit. The grading size can be adjusted at will 3. It is made of stainless steel, with high hardness and no deformation, and the equipment is solid and durable. At the same time, it is equipped with a large fruit tray (you can choose to load on one side of the machine or on the top of the machine), which can pick out bad fruits. One machine can be used for many purposes. 4. The number and size of grading can be adjusted at will.

Belt press juicing machine for fruit vegetable Use for : 01.fruit juice 02.vegetable dehydration or juce 03.enzyme juice 04.Extraction of medicinal juice 1. High lift and large flow, strong pumping force, not easy to block, precision casting pump body, lasting work, high efficiency and energy saving, after-sales guarantee 2. Long service life. The product is equipped with a new automatic deviation correction and tension system, automatic operation, uniform distribution of materials, extended filter bag life, and long bearing service life 3. Rust-proof and corrosion-resistant, tough shell, stable operation, unique oblique lengthened wedge design, more stable operation and low noise 4. The treatment effect is good. Two sets of independent backwashing systems are adopted. The multi-roll diameter decreasing backlogs are compact in layout and the filter cake has high solid content. 5. Efficient, convenient and ultra-long gravity dewatering area, with large bearing capacity, strong processing capacity, low power consumption and low operating cost 6. Juice yield 85% Small capacity 500-3000kg/h,filter belt width 500-2000mm,power 1.5-3kw, filter belt speed 1.5-3.5m Big capacity 3-20T/hour,power 14.7-41kw ,machine size length 3100-5420mm Width 1475-3430mm high 1820-2420mm

Ethanol alcohol distillation column 1. It is standard 95-96% alcohol equipment. Also it can distill pure water. 2.The distillation system has  three columns  and  continuous  distillation  process.The process is the  same as industrial(large scale) alcohol equipment.  Mash distillation  column distills  fermented  mash or light alcohol  to 50% alcohol ethanol . It has red copper bubble cap trays, standard design. It auto continuously feeds material liquid, auto continuously produces 50% alcohol ethanol and auto continuously discharges waste,  ethanol discharge in waste 0.05%, better than international standard requirements. The first rectification distillation  column  increases  alcohol degree  to 70-75% ,  separates  fusel oil and high boiling point  Impurities.  It auto discharges waste water,  ethanol discharge in waste 0.05%, better than international standard requirements. The second rectification distillation  column  increases alcohol degree to 95%,  separates low boiling point  impurities  like acetaldehyde and methanol . 3.  The rectification system uses  industrial(large scale) standard process, but the whole set alcohol equipments are installed in one frame, like integration  module, even  you can run it by a button.

Distillation column For Ethanol Alcohol Plant 1. It is standard 95-96% alcohol equipment. Also it can distill pure water. 2. The distillation system has three columns and continuous distillation process.The process is the same as industrial(large scale) alcohol equipment.     a. Mash distillation column distills fermented mash or light alcohol to 50% alcohol ethanol .  It has red copper bubble cap trays, standard design. It auto continuously feeds material liquid, auto continuously produces 50% alcohol ethanol and auto continuously discharges waste, ethanol discharge in waste ?¤0.05%, better than international standard requirements.     b. The first rectification distillation column increases alcohol degree to 70-75% , separates fusel oil and high boiling point Impurities. It auto discharges waste water, ethanol discharge in waste ?¤0.05%, better than international standard requirements.     c. The second rectification distillation column increases alcohol degree to 95%, separates low boiling point impurities like acetaldehyde and methanol . 3.  The rectification system uses  industrial(large scale) standard process, but the whole set alcohol equipments are installed in one frame, like integration module, even you can run it by a button.