The CPI -4600 Series compressor lubricants are formulated using premium polyalphaolefi n (PAO) synthetic base fluid, coupled with a high performance additive package. These compressor lubricants feature excellent thermal and oxidation stability enabling them to operate over a wide range of temperatures without coking, deposit formation or corrosion. The lubricants have low volatility and exhibit excellent miscibility with hydrocarbon gas and good compatibility with mineral oil lubricants. The CPI -4600 Series are recommended for refrigeration services due to excellent low temperature properties. They are wax-free as they are synthetic. A low pour point prevents lubricants from congealing in refrigeration lines. High film strength provides lubricity even when diluted with refrigerant. Applications and Compressor Type Propylene Refrigeration Oil-flooded rotary screw compressors Liquid ring vacuum pumps Other applications requiring an oxidative and thermally resistant lubricant Features and Benefits Hydrocarbon miscibility Work well with hydrocarbon gas in industrial refrigeration systems Oxidatively stable Longer system life Low volatility Reduced maintenance, reduced top-up High viscosity index Wide temperature range of operation Excellent lubricity Increased efficiency, reduced cost of operation
The CPI -1516 Series compressor lubricants are formulated using premium polyalkylene glycol (PAG), coupled with a high performance additive package. The lubricants are specifically formulated to ensure shear stability, corrosion protection, and excellent lubricity. These compressor lubricants feature excellent protection against yellow metal staining by careful selection of a combination of corrosion inhibitors. This, coupled with unparalleled oxidative and thermal stability ensures that the use of these lubricants over a wide range of applications and systems will result in a long, trouble-free and uninterrupted service interval. The CPI -1516 Series are specifically advantageous in high-temperature applications, particularly as the low volatility and high viscosity index means that there is significantly reduced lubricant in the gas stream, ensuring that the use of these lubricants over a wide range of applications and systems will result in a long, trouble-free and uninterrupted service interval. Applications and Compressor Type Flooded rotary screw compressors Propane refridgeration Features and Benefits Corrosion protection (yellow metals) Enhanced system reliability and reduced down-time Oxidatively stable Longer system life Extremely low volatility Reduced maintenance, reduced top-up Excellent lubricity Increased effi ciency, reduced cost of operation High viscosity index Satisfactory use over wide range of operational temperatures
The CPI -1515 Series compressor lubricants are formulated using premium polyalkylene glycol (PAG), coupled with a high performance additive package. The lubricants are specifically formulated to give negligible solubility or dilution in hydrocarbon gases These compressor lubricants feature excellent protection against hydrogen sulphide (H2S) within the gas stream. Corrosion protection, low pour point and excellent lubricity ensure that the use of these lubricants over a wide range of applications and systems will result in a long, trouble-free and uninterrupted service interval. The CPI-1515 Series are specifically advantageous in high-temperature applications, particularly as the low volatility and negligible dilution with hydrocarbons means that there is significantly reduced lubricant in the gas stream, ensuring that the use of these lubricants over a wide range of applications and systems will result in a long, trouble-free and uninterrupted service intervals. Applications and Compressor Type Flooded rotary screw compressors Centrifugal compressors Liquid ring vacuum pumps Features and Benefits Hydrocarbon insoluble Insignifi cant dilution in operation Corrosion protection (H2S) Resistance against H2S corrosion Oxidatively stable Longer system life Extremely low volatility Reduced maintenance, reduced top-up Excellent lubricity Increased efficiency, reduced cost of operation
The CPI-1508 Series compressor lubricants are formulated using a polyalkylene glycol (PAG) base fluid combined with a high performance additive package. These lubricants are specifically formulated to give negligible dilution with hydrocarbon gases. These compressor lubricants feature excellent protection against hydrogen sulfide (H2S) in the gas stream. Corrosion protection, oxidative and thermal stability enable the use of these lubricants over a wide range of temperatures without varnish or deposit formation. The high viscosity index (VI) and negligible hydrocarbon dilution enables the CPI-1508 Series lubricants to operate over wide ranges of temperature and gas composition with small changes in viscosity compared to other types of lubricants. The CPI-1508 Series fluids are especially advantageous in compressors operating in harsh chemical environments, particularly sour gas (H2S present) applications, due to their robust formulation. Applications and Compressor Type Flooded rotary screw compressors Sour gas applications Heavy hydrocarbon gas stream applications Features and Benefits Hydrocarbon insoluble Negligible dilution due to hydrocarbons in operation Corrosion protection (H2S) Resistance against H2S corrosion Oxidatively stable Longer system life High viscosity index Small viscosity changes over wide temperature ranges
We have all kind of D2 and Bace Oil bulk quantities available. We have also bitomen with cheap price available stock. Base oils are used to manufacture products including lubricating greases, motor oil and metal processing fluids. Product origin : Russia Key Specifications/Special Features : Grades : SN 150, SN 300, SN 500 Size and Packgaing details : Flexitank, IBC, Drums
1. Characteristics - Appearance Method - Visual Unit - Result - Bright & Clear 2 . Characteristics - Color Method - ASTM D 1500 Unit - ASTM Color Result - 2.5 3 . Characteristics - Density @ 15.6 Method - ASTM D 1298 Unit - G/CM3 Result - 0.868 4 . Characteristics - Kinematic Viscosity @ 100 Method - ASTM D 455 Unit - MM2/S Result - 15.92 5 .Characteristics - Kinematic Viscosity @ 40 Method - ASTM D 455 Unit - M2/S Result - 107.38 6 . Characteristics - Viscosity Index Method - ASTM D 2270 Unit - Result - 158.47 7. Characteristics - Pour Point Method - ASTM D 97 Unit - Result - -6 8 . Characteristics - Flash Point Method - ASTM D 92 Unit - Result - 192
Organic fertilizers, organic pest control products , pesticides, fertilizers , castor oil cakes, castor seeds , and fly ash.
This is chemical setting Furan based chemical resistant mortar which is combination of Liquid and Powder, when mixed in proper proportion from workable mortar which after setting and curing give of liquid and give black highly cross linked composites. Furan When set and cured is resistant to highly corrosive acids, alkalis and to powerful organic solvents such as ketones, Aromatic and Chlorinated solvents. It has extreme resistant to Acidic & alkalis, Salts, Greases and Detergents. It resists to Organic & Inorganic acids at their boiling temperature. It is suitable against mild chlorine Gas (dry) phosphorous trichloride, pyridine at room temperature. Furan is especially useful where resistance to mixed media such as aqueous acids /alkalis and organic solvents is needed in chemical plant process and waste streams. Carbon filled Furan is used against corrosive effect of hydrofluoric acid & its salts. PREPARATION OF FURANE MORTAR : Mortar consist of Furan solution and Furan powder. The average mixing ratio necessary to obtain mortar with good working consistency is 1 part by weight Solution & 3 part by weight powder. The ratio will vary slightly depending on temperature and working conditions.Stir the liquid thoroughly before using. Place liquid in a suitable shallow mixing pan. Add powder by weight in the solution mix thoroughly and rapidly until all lumps are dispersed and the mortar is completely homogenous. Spread out the mortar in a thin layer, not more than ¾ thick, to dissipate the heat of reaction and lengthen the working life. Batch size can be varied depending upon the temperature and the speed with which the masons are working. Very large batches will become stiff quite rapidly. Make sure that all the Furan Motrar is used from the pan before another batch is mixed.When working at temperature above 40 C, very small batches not more than 2 Kgs, should be prepared. When working at temperature below 15C the liquid should be kept warm.
DATA SHEET FOR EPOXY EPOXY COATING :- INTRODUCTION - EPOXY COATING (HYB) is a two part high solids solvent free epoxy phenolic resin based coating system designed for hard wearing, smooth surface finish for floors, walls and on steel structures. Nonskid surface finish can be achieved on floor, if required. FEATURES: 1) Hard Wearing 2) Non Dusting 3) Excellent Surface Finish 4) Non Smelling 5) Good Aesthetics 6) Highly Chemical Resistant APPLICATION: 1.Stir well before mixing Part A and Part B and mix in the prescribed ratio. 2.Apply one coat of EPOXY primer on the clean and dry surface. 3.EPOXY COATING (HYB) should be applied on the surface by brush or roller within 24 hrs. After application of primer coat it should be allowed to air dry for min. 4 hrs. Preferable in a dust free atmosphere. 4.Apply min. 2 coats with the intercoat interval of 6-8 hrs. PRODUCT SPECIFICATIONS: Application - Brush, Roller Mixing Ratio - As Directed on Packing Port Life - 30 Mins. Drying Time - Touch Dry- 30 Min, Hard Dry 6 Hrs. - Intercoat Interval 6-8 Hrs. Min. - Dry Film Thickness 125-150 Microns/per coat - depending on porosity Covering Capacity - 6-8 sq.met/kg per coat depending on porosity, roughness & method of application. Color Shades - All Standard Shades RECOMMENDED USES: 1) Food & Pharmaceutical 2) Work Shop 3) Clean Room Application 4) Chemical Resistant Coating for Concrete& Steel 5) Petrochemical, Fertilizer plants METHOD OF APPLICATION: SURFACE PREPARATION The long-term durability of the applied Epoxy coating (HYB) epoxy coating is dependent on the adhesion between sub-base and coating material. It is most important therefore, that the substrate surfaces are correctly prepared prior to application. 1.Before application of the Epoxy coating (HYB) surface should be free from loose partials, rust, oils, grease or earlier coatings and should be totally dry. 2.New concrete or cementations surface should be placed at least 28 days and have a moisture content of less than 5% before application of Epoxy coating (HYB) 3.After surface is dry, all repair work like sealing of joints, cracks filling of cavities and crevices should be carried out. HEALTH & SAFETY - Keep the containers tightly closed when not in use. Avoid contact with skin & eyes. It comes in contact with the body, wash affected parts with plenty of water and contact a doctor. Other known sector for Epoxy floor lining, Epoxy garage floor lining, Concrete epoxy lining, Concrete floor epoxy lining, Epoxy pipe lining, Marine epoxy lining, Sub marine epoxy lining, Basement lining epoxy floor shield, Louisiana, Oregon, Chip lining color epoxy floor, Aviation lining epoxy interior.
Rotol Long Drive NLGI 3 This is Lithium based multipurpose grease manufactured from superior quality base oil and soap. Its excellent structural stability, water resistance property, higher drop point and very good oxidation stability ensures long grease & component life. It has outstanding rust protection ability.
Franchise opportunity for Greases and specialities Our aspiration is to build strong and mutually beneficial relationships by appointing Exclusive Distributors world-wide, on a long-term basis. Our expertise in Genuine Spare Parts ( For Cars & Trucks) + Lubricants can be a unique business proposal to distributors across the world. We can also entertain deal-to-deal enquiries for specific grades. Ghassan Aboud Auto Spare Parts & Petrochem FZE https://www.aboudcar.com/lubricants-petrochemicals/ Ghassan Aboud Auto Spare Parts & Petrochem FZE are based in Jebel Ali Free-zone, Dubai, UAE, we export Genuine Spare Parts across 80 countries in the world. In our efforts to meet growing customer demands and provide a complete solution to them, we have diversified into the field of Lubricants.
Roll blank is cast by imported centrifugal compound casting equipment. High Ni Cr Mo alloy is adopted, the thickness of the alloy layer is large and even 30-35mm, and the hardness is up to Hs78-80. Through shaft cold assembly technology or half shaft end cover forging shaft head is adopted, which can be processed and manufactured according to the requirements of different models of users. It has been used by many imported rolling mills, and various technical indexes have reached or exceeded foreign standards.
Limboto 4350
As a leader in the production of lubricants (mainly greases), we serve many customers; we provide our products as well as we make private labels for many well-known brands.
We produce varieties types of grease including general lithium grease, molybdenum disulfide lithium grease, hp high temperature grease, xhp high temperature grease, hp-r almighty high temperature grease, special lubricating grease for continuous casting machine, high temperature white special lubricating grease.Please contact us.
This product is multiple-effect, long lasting grease refined from hydroxy aliphatic hydrocarbon lithium soap thickened mineral oil. We produce varieties types of grease including general lithium grease, molybdenum disulfide lithium grease, hp high temperature grease, xhp high temperature grease, hp-r almighty high temperature grease, special lubricating grease for continuous casting machine, high temperature white special lubricating grease.Please contact us!
Excellent high temperature resistance,extreme pressure wear resistance, greatly improve the anti clamping capacity. Excellent high temperature lubrication, to reduce the coefficient of friction and power consumption. With the property of water-resistance, seal property, mechanical stability. It has a significant effect on prolonging the service life of equipments and increasing the output power. We produce varieties types of grease including general lithium grease,molybdenum disulfide lithium grease,HP high temperature grease,XHP high temperature grease,HP-R Almighty high temperature grease, special lubricating grease for continuous casting machine,high temperature white special lubricating grease.
Excellent high temperature resistance,extreme pressure wear resistance, greatly improve the anti clamping capacity. Excellent high temperature lubrication, to reduce the coefficient of friction and power consumption. With the property of water-resistance, seal property, mechanical stability, oxidation stability, it has a significant effect on prolonging the service life of equipments and increasing the output power. We produce varieties types of grease including general lithium grease,molybdenum disulfide lithium grease,HP high temperature grease,XHP high temperature grease,HP-R Almighty high temperature grease, special lubricating grease for continuous casting machine,high temperature white special lubricating grease.Please contact us!
Drop point min 90c Color light brown or golden yellow Nlgi 3 Stretchy 196kg-16kg(drum wieght)