Minimum Quantity:1000,000MT PER YEAR DIESEL AUTOMOTIVE GAS OIL (AGO ) (specification) PARAMETER TEST METHOD IP/ASTM LIMITS Specific Gravity 15/15 deg C 160/D1298 0.820min,0.870 max Color (ASTM) D 150000 3 max Flash Point (deg. C) 66 Total Sulphur ( % wt) 0.50 max
MIN:1000,000MT per year CIF :ASWP DIESEL AUTOMOTIVE GAS OIL (AGO ) (specification) PARAMETER TEST METHOD IP/ASTM LIMITS Specific Gravity 15/15 deg C 160/D1298 0.820min,0.870 max Color (ASTM) D 150000 3 max Flash Point (deg. C) 66 Total Sulphur ( % wt) 0.50 max
FOB ROTTERDAM - DIP and PAY payment terms Specifications added in the picture section. Procedure : - Send LOI to Stoix Trading FZCO to initiate the process and we will send you our SCO. 1 Buyer sends ICPO in line with seller working procedures alongside his/her Tank Storage Agreement (T.S.A.) on receipt and acceptance of Seller's Soft Offer 2. Seller issues Commercial Invoice (C.I.), Buyer Signs within 24 hours and returns to Seller within its validity 3. Upon receipt and review of the signed C.I., seller issues Dip Test Authorization (D.T.A) to be completed and signed by buyer/ Buyer's logistics in order for Dip Test to be conducted alongside counter signed copies of the C.I 4. Buyer returns the Dip Test Authorization (DTA) fully completed and signed within its validity and upon successful review of the completed DTA, seller issues the below full POP documents: - A. Fresh SGS Report (Not older than 72 hours); B. Product Reservoir Receipt; C. Accreditation Certificate; D. Product Passport (Quantity and Quality Analysis); E. Authorization to Sell and Collect Certificate (ATSCC); F. Pre-Injection Report (PIR); G. NCNDA/IMFPA (To be completed by all intermediaries); H. Certificate of Product Origin; Authority to Verify (ATV) either physically or otherwise. 5. Upon receipt and confirmation of the above POP Documents, Buyer provides its testing officials (SGS or INTERTEK) and the needed test are carried out on the product in seller's tanks; 6. Buyer upon successful Dip Test makes full payment by MT103 / TT wire transfer for the total product and Seller pays commission according to NCNDA/IMFPA to all intermediaries involved in the transaction within 24 hours after confirmation of buyer's payment and injection commences immediately. 7. Seller issues a contract for buyer's desired duration upon successful completion of the trial order.
Hello Product: Diesel fuel (EN590 10 PPM) Origin: Kazakhstan Quantity Trial: 30,000 To 500,000 MT or Requested CIF price: GROSS USD $485.00 MT NET: USD $475.00 MT FOB Price: GROSS USD $ 475.00 MT NET: USD $465 MT Product Inspection: SGS Product Payment: T/T, MT103, /SBLC/DLC Grade/Specification: Standard Export Grade and Quality Possibility of safe Transportation is guaranteed Kindly Contact you Thank you!
1. BUYER issues LOI with full company KYC including: Company Details, Contact Details for Signing Authority, and Passport Facing Page.2. SELLER issues Soft/Full Corporate Offer SCO/FCO) including: Full Company Details, Contact Details for Signing Authority, Passport Facing Page, and Company Banking Details.3. BUYER accepts terms and issues Irrevocable Corporate Purchase Order (ICPO) addressed to the SELLER. ICPO MUST include SELLERâ??S procedures on BUYERâ??S official company letterhead.4. Included with ICPO, BUYERâ??S Bank issues a BCL/POF/RWA bearing the SCO REF Number: SCOKVPL0524001 a. BUYER authorizes SELLER and/or SELLERâ??S Financial Service Provider to verify BCL/POF/RWA via BUYERâ??S Bank. 5. SELLER issues PPOP upon successful verification of BUYER bank BCL/POF/RWA. Documents included in the PPOP document package are:a. SELLER Bill of Lading b. Loaded SGS Report Q&Q -(Notarized).c. Chief Officers Ullage report-(Notarized) d. SELLER Charter Party Agreement (CPA) e. Product Passport (product analysis report) -(Notarized) f. Certificate of Origin -(Notarized) g. Statement of Product Availability -(Notarized) h. Commitment and Assurance Letter to supply -(Notarized) i. Authority to sell and collect (ATSC) -(Notarized) 6. End-to-end procedure after issuing PPOP is NOT expected to exceed TEN (10) working days, including 96 hours for vessel loading laycan. 7. Included with PPOP, SELLER issues Commercial Invoice (CI), and NCNDA / IMFPA to BUYER. 8. The BUYER signs and returns the executed documents to the SELLER. If the documents are not executed in a timely fashion. The SELLER may terminate this agreement without prejudice to any rights or remedies of the SELLER. Notice will be in writing. 9. After safely receiving the PPOP and returning the executed CI and documents. The BUYER MUST issue either MT 700 DLC or MT 799 BLOCKED FUNDS to the full value of commercial invoice amount. 10. Additionally, the BUYER MUST present his vessel for loading in the nominated port and be ready within 24 Hrs to load the full cargo. When requesting the UDTA to be issued, BUYER MUST provide the following details to the SELLER: a. VESSEL NAME b. VESSEL Q88 c. Vessel Agent full contact details 11. After fund instruments and vessel nomination details are received. The SELLER will issue Unconditional Dip Test Authority (UDTA) to the BUYER. SELLERâ??S agent will contact the BUYERâ??S agent and program the vessel for ShipTo-Ship (STS) loading within 24 hours. 12. BUYER loading LAYCAN will commence 24hrs after the UDTA is issued to the BUYER. BUYER has 96 hours Laycan to finish loading the vessel. CIN: U74999DL2016PTC298417 13. BUYER Dips Tanks prior to vessel berthing. BUYER obtains fresh SGS Quantity and Quality report. 14. After successful Dip Test and Q&Q report. BUYER instructs account manager to make full payment of the full value of commercial invoice via SWIFT MT103 to SELLERâ??S nominated accounts.
Fresh vegetables, fresh products: orange, potatoes, yellow onion, red onion, fresh garlic, dry garlic, dry white beans, pomegranate, intermediation for diesel en590, jp54 aviation jet fuel a1, d6 diesel oil , d2 diesel oil, lpg, lng, automotive gas oil (ago) intermediation for sugar icumsa 45, yellow corn, wheat.Intermediation for diesel en590, jp54 aviation jet fuel a1, d6 diesel oil , d2 diesel oil, lpg, lng, automotive gas oil (ago) intermediation for sugar icumsa 45, yellow corn, wheat
MIN: 1000000 PER YEAR CIF/FOB DIESEL AUTOMOTIVE GAS OIL (AGO ) (specification) PARAMETER TEST METHOD IP/ASTM LIMITS Specific Gravity 15/15 deg C 160/D1298 0.820min,0.870 max Color (ASTM) D 150000 3 max Flash Point (deg. C) 66 Total Sulphur ( % wt) 0.10 max
C) Diesel EN590 500 PPM
Automobile diesel fuel (EN 590) Grade E (winter), recommended for use at ambient temperatures up to minus 15 C (limiting filterability temperature). Diesel fuel EN 590 (EN 590) Grade E is obtained from petroleum refined products and is intended for use as automotive fuel for diesel engines of cars and trucks. Diesel fuel meets the requirements of the international standard EN 590/2000 and is characterized by a low content of sulfur, aromatic hydrocarbons and a high cetane number, which leads to an overall reduction in sulfur oxide emissions, a decrease in the amount of particulate matter in exhaust gases and the formation of deposits in the fuel system of cars and heavy vehicles, reducing exhaust smoke and is the key to good starting properties of the fuel during cold start of the engine. The oil refining industry produces diesel fuel in accordance with GOST 305-82 of three grades: L - summer, used at ambient temperatures above 0 C; 3 - winter, used at temperatures up to -20 C (in this case, winter diesel fuel should have a stagnation
EN590 was introduced to coincide with the development of new emissions standards across the European Union. The overall goal has been to reduce the sulphur content of diesel fuel. Sulphur had been used as a lubricant in the fuel. Its role is taken by special additives in ULSD. Since 2007, diesel that conforms to EN590 has been referred to as Ultra Low Sulphur Diesel (ULSD) in the European Union. The phrase Ultra Low Sulphur Diesel is governed by different standards in other parts of the world. EN590 describes the physical properties that all automotive diesel fuel must meet if it is to be sold in the European Union, Croatia, Iceland, Norway and Switzerland. The EN 590 had been introduced along with the European emission standards. With each of its revisions the EN 590 had been adapted to lower the sulphur content of diesel fuel since 2007 this is called ultra low sulphur diesel as the former function of sulphur as a lubricant is absent (and needs to be replaced by additives). The quality of European diesel fuels is specified by the EN 590 standard. While these specifications not are mandatory, they are observed by all fuel suppliers in Europe. Automobile diesel en 590 is intended for application in diesel engines. Diesel motor fuel quality meets the requirements of European Standard EN 590. For operation in the conditions of a temperate climate following marks of fuel diesel automobile EN 590 are offered: Grade C limiting filterability temperature -5 C; Grade D limiting filterability temperature -10 C; Grade E limiting filterability temperature 15 C; Grade F limiting filterability temperature -20 C. The entire volume of produced diesel fuel quality meets the requirements for fuels for vehicles of Euro 4 and Euro 5. Low sulfur content in diesel EN 590 reduces emissions of sulfur oxides into the atmosphere, which is especially important for for inhabitants of big cities.
Oil & gas products, en590 diesel, jet fuel a1, d6 virgin fuel, petcoke etc, petroleum products, metal commodities like copper cathode & aluminium ingots.Brokering services
Transaction algorithm: 1. The Customer provides the LOI to the Supplier for consideration and decision-making on possible cooperation. 2. The Supplier, having considered the LOI, sends a Soft Corporate Offer to the Customer. 3. The Customer, having considered the SCO, provides the supplier with an ICPO confirmed by the bank, which will take part in the transaction as a guarantor of the transaction on the part of the Customer. 4. The Supplier accepts the Customer's ICPO and submits the Full Corporate Offer (FCO) for review by the customer. 5. The Supplier submits to the Customer a Sample General Contract for the supply of goods for study and adjustments. 6. After agreeing on the general contract, the Supplier and the Customer carry out the procedure for signing the contract and its verification. At the time of signing the contract, the parties exchange the documents, which are confirmed by banks that serve the parties and conduct transactions on the transaction. 7. The customer issues Proof of Funds (POF) confirmed by the customer's bank, the Supplier transfers to the customer Proof of Product (POP) confirmed by the Supplier's bank. 8. When signing an annual contract, the Customer provides the Supplier with an annual bank guarantee in the form of a Standby Letter of Credit from a bank with an international credit rating of at least A +, this guarantee is equivalent to the cost of the monthly volume of delivery of goods and is a guarantee of payment of funds for the goods in the event of force majeure. 9. To open the Customer's bank guarantee, the Supplier shall provide a Performance Bond determined as a percentage of the price. 10. After carrying out the procedures indicated above, the process of accumulation of goods in the Port begins, the charter of the vessel is provided and the delivery of goods is carried out in accordance with the schedule of deliveries and quality and quantity checks under contractual obligations. 11. After the arrival of the goods at the port of the Customer, the quality and quantity of the goods are checked and controlled. 12. The Customer, having received the goods at the port, pays by direct payment MT 103 to the Supplier's bank account for the full amount of the cost of the goods delivered in a specific period of time. Payment is made no later than 3-5 days from the date of receipt of the goods. Supplier's Guarantee Bank: JP Morgan Chase New York (AAA credit rating). The customer's bank must meet international standards and have an international credit rating of at least A +. If the Customer's bank has a credit rating below A +, then the transaction is possible only if there is confirmation of the guarantees of a bank with a low rating by an international bank with a rating not lower than A +. In other cases, the transaction will not be implemented. The following deliveries are carried out according to the schedule, which is an integral part of the general contract.
We are outsourcing Diesel 10 PPM
Can supply 10 ppm diesel to meet european specifications from fob houston. Contact if interested and qualified.
Can supply 10 ppm diesel to meet european specifications from fob houston. Contact if interested and qualified.
Crude oil and derivatives, Diesel gas d2, d6 aviation kerosene ts1/ jp54 gasoline 89/93 octane's aviation jet fuel a1 espo blend crude diesel en590 (10 ppm ) diesel en590 (50 ppm ) light cycle oil (lco) liquified natural gas (lng)) liquified petroleum gas (lpg) mazut 100 urea petcoke .
Seller has existing ready stock of 100 million gallons of D6 Virgin oil fuel in Houston tank farm available for buyers & he is able to do tank to tank in Houston at a very competitive price.
We can supply Diesel en590 10ppm with very good price. Not necessary to follow seller process, seller will follow buyer own procedure. If you want we can immediately arrange a meeting with End seller Only for serious buyer
EN590 10 PPM | JET A1 | FOB ROTTERDAM AND HOUSTON
En590 10 , D6 , Naphtha , Jetfuel, Nigerian Crude, Petcoke, and Iron Ore ( Mexico origin ).
