The durable metal structure garage kit can not only protect your vehicle, but also add value to your property. The steel structure garage is an ideal building structure with simple installation, fast construction speed, low cost and environmental protection. Compared with concrete structures, steel structure building kits have excellent seismic performance. In earthquake prone areas, prefabricated metal structures are the best building structures. In addition, the installation of prefabricated metal buildings is simple, and the construction speed is only one third of that of concrete structures. Steel column and beam The column and roof beams of the steel workshop building are usually H-shaped steel made of section steel and steel plate. Columns and steel beams welded with steel plates need to be corrected after assembly and welding to prevent the H-section steel from deforming due to welding deformation. Steel columns and beams are usually connected by welds or bolts, which are the workshop s main load-bearing structure. Roof and wall panels Roof and wall panels are divided into two types: corrugated single sheet and sandwich panels. The single color sheet is usually used for buildings without thermal insulation requirements, relying on purlins or wall girt to form a roof and wall enclosure structure. Sandwich panels are mainly used in buildings that require heat preservation and heat insulation. The sandwich panels core materials mainly include polyphenylene, polyurethane foam, rock wool, and glass wool.
Interior: Dash Kits, Floor Mats, Seat Covers, Steering Wheels, Sun Shades, Custom Gauges, Cargo Liners, Seats, Dash Covers, Shift Knobs, Car Organizers, Commercial Van Equipment, Pedals, and Exterior : Running Boards, Custom Grilles, Chrome Trim, Body Kits, Off-Road Bumpers, Bed Accessories, Grille Guards, Towing & Hitches, Headlights, Tail Lights, Tonneau Covers, Spoilers, Wind Deflectors, Custom Hoods, Roof Racks, Car Covers, Fender Flares, Mirrors, Bug Deflectors, Car Bras, License Plates & Frames, Vertical Doors, Light Covers, Winches, Bike Racks, Wiper Blades, Mud Flaps, Emblems & Logos, Sunroof Visors, Armor & Protection, Car Wraps, Car Tents, Soft Tops & Hard Tops, Commercial Van Equipment, Spare Tire Covers & Carriers, Snow Plows, Custom Horns, Lighting, Parts, Body Parts, and Audio And Electronics Performance Part Suspension Systems, Brakes & Rotors, Exhaust Systems, Air Intake Systems, Performance Chips, Engine Components, Transmission, Cooling Systems, Turbo & Superchargers, Fuel Systems, Ignition Systems, Steering, Starting & Charging, Driveline & Axles, Caliper Covers, Racing Gear, and Power Adders BODY PARTS Mirrors Headlights, Tail Lights, Bumpers, Fenders, Hoods, Grilles, Doors, Quarter Panels, Auto Glass, Trunks & Tailgates, Interior Parts, Rocker Panels + Floors, Chassis Frames & Body, Header Panels, Window Components, Wipers & Washers, and Roofs Lighting Headlights, Tail Lights, LED Lights, Fog Lights, Off-Road Lights, Signal Lights, Car Bulbs, Trailer Lights, Accessory Lighting, and Emergency & Warning Lighting. Weels & Tires Custom Wheels, Tires, Wheel & Tire Packages, Caliper Covers, Factory Wheels, Wheel Covers, TPMS Sensors, Tire Chains, Lug Nuts & Locks, Center Caps, Wheel Spacers, Spare Tire Covers & Carriers, Wheel & Tire Accessories, and Wheel & Tire Service Tools.
Fully Automatic Plastic Bottle Liquid Peanut Butter Juice Honey Oil Sauce Milk Water Filling Machine Liquid filling machine, can fill food and daily chemicals, including water, oil, sauce, shampoo, hand sanitizer, etc. The automatic piston filling machine adopts quantitative filling of the plunger bottle-in, positioning, filling and bottle-out are all automatically controlled by the PLC, conforming to the GMP standard. Applicable for medicine, food, daily chemicals, pesticides and fine chemicals, and other varieties of product filling. Specification Filling range: 50-1000ml Filling speed: 15-25/bottles/min(Base on100-500ml) Measurement accuracy: �±1% Power: 220V, 2.2kw Working air pressure: 6-7kg/m2 Gas consumption: 1mpa Machine weight: 600kg Features 1.Touch screen operation interface. 2.Up and down movement type filling, effectively prevent the foam from being produced, easy to take apart and wash. 3.The filling accuracy can reach �±1%. 4.The filling cylinder is ground, unique filling valve design, no leakage. 5.With no bottle no filling and automatic bottle stop function. 6.Design different positioning devices according to the actual situation of the bottle. 7.The equipment is easy to clean, can be disassemble without tools, it can also be cleaned online or high temperature sterilization. 8.PLC programmable control use Japan Mitsubishi. 9.Frequency converter adopts France Schneider 10.Pneumatic components adopt Taiwan Airtac. 11.Material contact parts are made of SUS 304# stainless steel. 12.The equipment meets the hygiene and safety standards. The user can choose the glass protective cover. If you would like to get other information about the liquid filling machine, please contact Soonfer Machine at any time. We will offer you professional and comprehensive packaging solution.
1. Introduction With new materials and technologies, Improved Kam Chung magnesium oxide board has better performance and avoids the defects of traditional MgO board. We use an alkali-resisting glass fiber net to increase product strength, and new technologies to prevent the "crying" phenomenon. In that case, our products can be used in humid area and no need to worry about quality problem. 2. Application Kam Chung Magnesia board is light in weight, resistant to fire, high in strength, good against moisture, thus suitable for a wide range of general building uses, such as ceiling, wall board and flooring for residential complex, hospital, school, workshop, warehouse, stadium or even furniture and billboard. 3. Specifications Size (mm) 2440*1220 Thickness (mm) 3 -20 Moisture content (%) 8 Density (g/cm3) 0.6-1.4 Wet Expansion Rate(%) 0.6 Thermal Conductivity (W/mïK) 0.30 Bending Strength(MPa) 10 Shock Resistance (Kj/) 2 Dry Shrinkage Rate (%) 0.3 Nail-holding Ability (N/mm) 25 Content of Chloridion (%) 10 Non- combustibility GB 8624-2006 Class A Impermeability No water drops on the other side 4. Advantages (1). Durable (2). Fire rated (3). Insect-free (4). Waterproof (5). Light weight (6). Energy efficient (7). Impact resistant (8). Easy installation (9). Environment -friendly
We are professional provide Cut Any Shape EPDM Sponge Rubber Foam With Adhesive Pads for more than 20 year experiences on die cutting services Factory Die Cut EPDM Foam Tape EPDM foam tape has excellent resistance to both water and sunlight. It has many of the same characteristics as NPVC foam in terms of look, feel, function, and durability. In fact, while EPDM grips are frequently requested, most applications can be more cost effectively satisfied with NPVC. EPDM foam tape is using EPDM foam as backing material and coated with one sided or two sided different kinds of adhesives. EPDM foam tape Features: Outstanding heat,ozone,and weather resistance. The resistance to polar substances and steam are also good. Excellent electrical insulating properties. Good resistance to ketones, ordinary diluted acids, and alkalines. Compatibility with fireproof hydraulic fluids, ketones, hot and cold water, and alkalis. EPDM foam tape Applications: For sealant and die cutting Vehicles, used in door seals, window seals, trunk seals, and sometimes hood seals. For die cut, cushioning, shockproof and sealing For pipeline wrapping for air conditions, auto trim attachment, door sealing strips, etc Used in glass-run channels, radiators, garden and appliance hose, tubing, pond liners, washers, belts, electrical insulation, vibrators, O-rings, solar panel heat collectors, and speaker cone surrounds
Normally a sheet metal laser cutting machine is priced at rmb 400, 000 to rmb 1, 000, 000, varying on brands, models and configuration. Gd. Hans yueming laser group, co. Ltd., a subsidiary of shenzhen hans laser technology co. Ltd (stock code: 002008), is a hi-tech company and a professional laser equipment manufacturer with a strong r&d team and experienced sales force. 18 years into business, headquartered in guangdong, hans yueming laser has established modern factories in dongguan, jiangsu, and shanghai with total floor area of over 100, 000 square meters and boasts over 100 processing units, a highly skilled workforce with more than 500 staff members, a wide range of laser equipment with 10 product lines and over 100 models, and an annual capacity of over 10, 000 sets of lase equipment. Hans yueming laser has introduces a serial of sheet metal laser cutting machine, varying on the size of working area, exterior design and configuration. For example, cma0606-d-g-b laser cutting machine is a sheet metal laser cutting machine with a 600mm*600mm working area, suitable for the cutting of glasses frame, metal chips and sheets where precision is demanded. This model boasts of efficiency, precision and of being room-saving. Cma1530-c-gh-d is another model of sheet metal laser cutting machine. This model has a much larger working area---1500mm*3000mm, suitable for the cutting of large metal and non-metal sheets used in making kitchenware, lamps, equipment cabinet, car accessories, fridge, air conditioning, elevator, etc. Ymshichangbu2018 Hans yueming laser is a national brand for laser equipment. Among its stellar range of laser equipment is sheet metal laser cutting machine, which has become a synonym for precision, efficiency, cost-effectiveness. If you are interested in our sheet metal laser cutting machine, please contact us at any time
DESCRIPTION ITLS PMS 60 is a single component elastomeric sealant without isocyanates. It cures rapidly under the effect of atmospheric humidity to form a flexible and resistant joint with very good adhesion on most materials. APPLICATION ITLS PMS 60 is suitable for industrial and refrigerated trailers, truck bodies, shipbuilding, air conditioning and ventilation units, sandwich panels and other industrial applications. ITLS PMS 60 can also be used for bonding and caulking different materials used in the building industry : concrete, wood, aluminum, most lacquered metals, polyester, glass, stone, ceramic, and so on. However, for difficult materials especially lacquered or non-ferrous metals, it is necessary to make tests beforehand. INSTRUCTIONS FOR USE SUBSTRATE PREPARATION: The substrates must be clean, even, dry, free of dust, oil, grease and any contaminants that could harm bonding. All traces of poorly adherent paints or coatings should be systematically removed beforehand. They may be cleaned with PMS primer, methylethylketone (MEK) or acetone. Check the compatibility of the solvent used with the substrates. It may be necessary to rub down the substrate beforehand. After rubbing down, the surface should be recleaned. Allow the substrate to dry after degreasing. When using solvents, extinguish all sources of ignition and carefully follow the safety and handling instructions given by the manufacturer. CAULKING: ITLS PMS 60 can be applied by a manual or pneumatic gun. After application, use a putty knife to smooth the joint with soapy water. Do not apply at a temperature under 5 C. In cold weather, store the cartridges at about 20 �°C before use. This product should be used within 24 hours of opening the cartridge protection; otherwise, the sealant could harden inside. Avoid any contact with non-cured polyurethanes during curing. CLEANING: Tools can be cleaned with PMS primer, MEK or acetone before the sealant has completely cured. After curing, abrasion is necessary. STORAGE AND SHELF LIFE 12 months in the original, hermetically sealed packagings between 5 and 25 C PACKAGING 290 mL cartridges and 600 ml sausages SAFETY Not classified as hazardous. Read the material safety data sheet before use.
IXPP foam Full name: Physical cross-linked polypropylene foam, Irradiation cross-linked polypropylene foam Explanation: Irradiation cross-linked Polypropylene (IXPP) foam is a kind of high-performance closed cell foaming material which is made of polypropylene and various fillers, additive, and foaming agents various material.� It� can be widely used in� the automotive� interior, aerospace, Construction material, Package and other industries. Features: 1.Excellent tensile, better compression properties than PE foam; 2.Soft, light-weighted, and flexible- 60% less weight than ordinary material 3.Good noise reduction, thermal insulation, water-proof;Shock absorption; 4.High temperature resistance-- It is suitable for application process with thermal stability up to 150 �ºC 5.Good weather resistance and aging behavior The good plasticity and the thermoformable and compression moulding features of IXPP foam make it available to combine with non-woven fabrics, velvet, knitted fabric, leather, fibrofelts, PP board, PU board, PS board, glass fiber board by hot melt gum, compressing moulding, lamination or casting method to foam automobile interiors, the whole process is non-pollution. Colour: black, white Size: rolls & sheets, customized Density: 33.33kg/m3-200kg/m3 Thickness: 0.3mm-55mm, also provide composite layer
1. KN95 stands for the regulatory standard for filtering facepiece respirators that are certified in China. 2. Regulated by the Chinese government under regulations GB2626-2006, GB2626-2019. 3. 95% protection against all particles that are greater than 0.3 um in diameter (bacteria, viruses, pollution particles, fine particles, dust, smog, pollen, etc.) 4. 3D foldable design, earloops, nose bridge/nosepiece, and provide excellent fitting and sealing. 5. 5-layer protection, skin-friendly (don't cause rash and skin irritation). 6. KN95 facemasks are FFP2 grade (N95 equivalent) and meet the guidance from the World Health Organization (WHO). Product Features Face mask with filter. Filters at least 95% of airborne particles (0.3 micron) particles. Thin & light multi-layer design reducing respiratory resistance. Substantial breathing area allows for sufficient airflow circulation without touching lips. High filtering ability, extremely low resistance, easy to breathe. Flexible & foldable design for extra comfort and easy storage. Glue-free and odorless face mask. CE Approved KN95 protective mask. Our KN95 face masks have been manufactured to EEA standards, and are used by hospitals, medical facilities and health professionals. Soft and flexible nose bridge can be adjusted to the face for comfort and perfect fit. Two strap ear-loop design stretches to fit all sizes providing a secure seal.. Highly compatible with other protective equipment like protective glasses and ear plugs. Helps prevent airborne diseases and infections.
Coated fabrics are flexible composite materials formed by applying bonding agents to either one or both sides of the fabric substrate and precisely coating it with different rubber compounds depending on the end application of the fabric. After the coating is cured it creates a strong bond between the rubber and the fabric. The final product after coating and curing is solid and flexible. It has a good stability and is washable, durable and much stronger than uncoated fabrics. Rubber coated fabrics are very close textured and therefore exhibit low permeation and diffusion. They can be electrically conductive and can also be weather, oil and temperature resistant. Zenith offers rubber-coated fabrics with special characteristics. We manufacture various types of fabrics for different applications such as barrier protection, abrasion resistance, air retention and high strength to weight ratios, flex resistance and resistance to chemical gases and fuels. Zenith uses basic fabrics such as Cotton, Nylon, Polyester, glass, knits, silk, Kevlar. Fabrics of various blends are coated with Nitrile, Chloroprene, Silicon, NR/SBR, Butyl, Hypalon (CSM), EPDM & blended polymers for variety of applications in the fields of Insulation, Defense, aviation, marine and offshore operations. ZRF fabrics are available from 0.3mm to 1.5mm thickness, 1.0 meter to 1.5 meter in width and in long lengths up to 100 meters. Zenith’s expertise in compounding is due to its extensive research and development program. All coated fabrics are vigorously tested for specification given by the customer. With our extensive testing procedures and fully equipped lab we ensure that all fabrics meet the highest quality standards. Zenith is using solvent-based coating, which gives better results as far as adhesion is concerned. Zenith’s large scale production capabilities and short development periods assures consistent quality and faster deliveries.
Coated fabrics are flexible composite materials formed by applying bonding agents to either one or both sides of the fabric substrate and precisely coating it with different rubber compounds depending on the end application of the fabric. After the coating is cured it creates a strong bond between the rubber and the fabric. The final product after coating and curing is solid and flexible. It has a good stability and is washable, durable and much stronger than uncoated fabrics. Rubber coated fabrics are very close textured and therefore exhibit low permeation and diffusion. They can be electrically conductive and can also be weather, oil and temperature resistant. Zenith offers rubber-coated fabrics with special characteristics. We manufacture various types of fabrics for different applications such as barrier protection, abrasion resistance, air retention and high strength to weight ratios, flex resistance and resistance to chemical gases and fuels. Zenith uses basic fabrics such as Cotton, Nylon, Polyester, glass, knits, silk, Kevlar. Fabrics of various blends are coated with Nitrile, Chloroprene, Silicon, NR/SBR, Butyl, Hypalon (CSM), EPDM & blended polymers for variety of applications in the fields of Insulation, Defense, aviation, marine and offshore operations. ZRF fabrics are available from 0.3mm to 1.5mm thickness, 1.0 meter to 1.5 meter in width and in long lengths up to 100 meters. Zenith’s expertise in compounding is due to its extensive research and development program. All coated fabrics are vigorously tested for specification given by the customer. With our extensive testing procedures and fully equipped lab we ensure that all fabrics meet the highest quality standards. Zenith is using solvent-based coating, which gives better results as far as adhesion is concerned. Zenith’s large scale production capabilities and short development periods assures consistent quality and faster deliveries.
Coated fabrics are flexible composite materials formed by applying bonding agents to either one or both sides of the fabric substrate and precisely coating it with different rubber compounds depending on the end application of the fabric. After the coating is cured it creates a strong bond between the rubber and the fabric. The final product after coating and curing is solid and flexible. It has a good stability and is washable, durable and much stronger than uncoated fabrics. Rubber coated fabrics are very close textured and therefore exhibit low permeation and diffusion. They can be electrically conductive and can also be weather, oil and temperature resistant. Zenith offers rubber-coated fabrics with special characteristics. We manufacture various types of fabrics for different applications such as barrier protection, abrasion resistance, air retention and high strength to weight ratios, flex resistance and resistance to chemical gases and fuels. Zenith uses basic fabrics such as Cotton, Nylon, Polyester, glass, knits, silk, Kevlar. Fabrics of various blends are coated with Nitrile, Chloroprene, Silicon, NR/SBR, Butyl, Hypalon (CSM), EPDM & blended polymers for variety of applications in the fields of Insulation, Defense, aviation, marine and offshore operations. ZRF fabrics are available from 0.3mm to 1.5mm thickness, 1.0 meter to 1.5 meter in width and in long lengths up to 100 meters. Zenith’s expertise in compounding is due to its extensive research and development program. All coated fabrics are vigorously tested for specification given by the customer. With our extensive testing procedures and fully equipped lab we ensure that all fabrics meet the highest quality standards. Zenith is using solvent-based coating, which gives better results as far as adhesion is concerned. Zenith’s large scale production capabilities and short development periods assures consistent quality and faster deliveries.
Coated fabrics are flexible composite materials formed by applying bonding agents to either one or both sides of the fabric substrate and precisely coating it with different rubber compounds depending on the end application of the fabric. After the coating is cured it creates a strong bond between the rubber and the fabric. The final product after coating and curing is solid and flexible. It has a good stability and is washable, durable and much stronger than uncoated fabrics. Rubber coated fabrics are very close textured and therefore exhibit low permeation and diffusion. They can be electrically conductive and can also be weather, oil and temperature resistant. Zenith offers rubber-coated fabrics with special characteristics. We manufacture various types of fabrics for different applications such as barrier protection, abrasion resistance, air retention and high strength to weight ratios, flex resistance and resistance to chemical gases and fuels. Zenith uses basic fabrics such as Cotton, Nylon, Polyester, glass, knits, silk, Kevlar. Fabrics of various blends are coated with Nitrile, Chloroprene, Silicon, NR/SBR, Butyl, Hypalon (CSM), EPDM & blended polymers for variety of applications in the fields of Insulation, Defense, aviation, marine and offshore operations. ZRF fabrics are available from 0.3mm to 1.5mm thickness, 1.0 meter to 1.5 meter in width and in long lengths up to 100 meters. Zenith’s expertise in compounding is due to its extensive research and development program. All coated fabrics are vigorously tested for specification given by the customer. With our extensive testing procedures and fully equipped lab we ensure that all fabrics meet the highest quality standards. Zenith is using solvent-based coating, which gives better results as far as adhesion is concerned. Zenith’s large scale production capabilities and short development periods assures consistent quality and faster deliveries.
Coated fabrics are flexible composite materials formed by applying bonding agents to either one or both sides of the fabric substrate and precisely coating it with different rubber compounds depending on the end application of the fabric. After the coating is cured it creates a strong bond between the rubber and the fabric. The final product after coating and curing is solid and flexible. It has a good stability and is washable, durable and much stronger than uncoated fabrics. Rubber coated fabrics are very close textured and therefore exhibit low permeation and diffusion. They can be electrically conductive and can also be weather, oil and temperature resistant. Zenith offers rubber-coated fabrics with special characteristics. We manufacture various types of fabrics for different applications such as barrier protection, abrasion resistance, air retention and high strength to weight ratios, flex resistance and resistance to chemical gases and fuels. Zenith uses basic fabrics such as Cotton, Nylon, Polyester, glass, knits, silk, Kevlar. Fabrics of various blends are coated with Nitrile, Chloroprene, Silicon, NR/SBR, Butyl, Hypalon (CSM), EPDM & blended polymers for variety of applications in the fields of Insulation, Defense, aviation, marine and offshore operations. ZRF fabrics are available from 0.3mm to 1.5mm thickness, 1.0 meter to 1.5 meter in width and in long lengths up to 100 meters. Zenith’s expertise in compounding is due to its extensive research and development program. All coated fabrics are vigorously tested for specification given by the customer. With our extensive testing procedures and fully equipped lab we ensure that all fabrics meet the highest quality standards. Zenith is using solvent-based coating, which gives better results as far as adhesion is concerned. Zenith’s large scale production capabilities and short development periods assures consistent quality and faster deliveries.
Coated fabrics are flexible composite materials formed by applying bonding agents to either one or both sides of the fabric substrate and precisely coating it with different rubber compounds depending on the end application of the fabric. After the coating is cured it creates a strong bond between the rubber and the fabric. The final product after coating and curing is solid and flexible. It has a good stability and is washable, durable and much stronger than uncoated fabrics. Rubber coated fabrics are very close textured and therefore exhibit low permeation and diffusion. They can be electrically conductive and can also be weather, oil and temperature resistant. Zenith offers rubber-coated fabrics with special characteristics. We manufacture various types of fabrics for different applications such as barrier protection, abrasion resistance, air retention and high strength to weight ratios, flex resistance and resistance to chemical gases and fuels. Zenith uses basic fabrics such as Cotton, Nylon, Polyester, glass, knits, silk, Kevlar. Fabrics of various blends are coated with Nitrile, Chloroprene, Silicon, NR/SBR, Butyl, Hypalon (CSM), EPDM & blended polymers for variety of applications in the fields of Insulation, Defense, aviation, marine and offshore operations. ZRF fabrics are available from 0.3mm to 1.5mm thickness, 1.0 meter to 1.5 meter in width and in long lengths up to 100 meters. Zenith’s expertise in compounding is due to its extensive research and development program. All coated fabrics are vigorously tested for specification given by the customer. With our extensive testing procedures and fully equipped lab we ensure that all fabrics meet the highest quality standards. Zenith is using solvent-based coating, which gives better results as far as adhesion is concerned. Zenith’s large scale production capabilities and short development periods assures consistent quality and faster deliveries.
Coated fabrics are flexible composite materials formed by applying bonding agents to either one or both sides of the fabric substrate and precisely coating it with different rubber compounds depending on the end application of the fabric. After the coating is cured it creates a strong bond between the rubber and the fabric. The final product after coating and curing is solid and flexible. It has a good stability and is washable, durable and much stronger than uncoated fabrics. Rubber coated fabrics are very close textured and therefore exhibit low permeation and diffusion. They can be electrically conductive and can also be weather, oil and temperature resistant. Zenith offers rubber-coated fabrics with special characteristics. We manufacture various types of fabrics for different applications such as barrier protection, abrasion resistance, air retention and high strength to weight ratios, flex resistance and resistance to chemical gases and fuels. Zenith uses basic fabrics such as Cotton, Nylon, Polyester, glass, knits, silk, Kevlar. Fabrics of various blends are coated with Nitrile, Chloroprene, Silicon, NR/SBR, Butyl, Hypalon (CSM), EPDM & blended polymers for variety of applications in the fields of Insulation, Defense, aviation, marine and offshore operations. ZRF fabrics are available from 0.3mm to 1.5mm thickness, 1.0 meter to 1.5 meter in width and in long lengths up to 100 meters. Zenith’s expertise in compounding is due to its extensive research and development program. All coated fabrics are vigorously tested for specification given by the customer. With our extensive testing procedures and fully equipped lab we ensure that all fabrics meet the highest quality standards. Zenith is using solvent-based coating, which gives better results as far as adhesion is concerned. Zenith’s large scale production capabilities and short development periods assures consistent quality and faster deliveries.
Coated fabrics are flexible composite materials formed by applying bonding agents to either one or both sides of the fabric substrate and precisely coating it with different rubber compounds depending on the end application of the fabric. After the coating is cured it creates a strong bond between the rubber and the fabric. The final product after coating and curing is solid and flexible. It has a good stability and is washable, durable and much stronger than uncoated fabrics. Rubber coated fabrics are very close textured and therefore exhibit low permeation and diffusion. They can be electrically conductive and can also be weather, oil and temperature resistant. Zenith offers rubber-coated fabrics with special characteristics. We manufacture various types of fabrics for different applications such as barrier protection, abrasion resistance, air retention and high strength to weight ratios, flex resistance and resistance to chemical gases and fuels. Zenith uses basic fabrics such as Cotton, Nylon, Polyester, glass, knits, silk, Kevlar. Fabrics of various blends are coated with Nitrile, Chloroprene, Silicon, NR/SBR, Butyl, Hypalon (CSM), EPDM & blended polymers for variety of applications in the fields of Insulation, Defense, aviation, marine and offshore operations. ZRF fabrics are available from 0.3mm to 1.5mm thickness, 1.0 meter to 1.5 meter in width and in long lengths up to 100 meters. Zenith’s expertise in compounding is due to its extensive research and development program. All coated fabrics are vigorously tested for specification given by the customer. With our extensive testing procedures and fully equipped lab we ensure that all fabrics meet the highest quality standards. Zenith is using solvent-based coating, which gives better results as far as adhesion is concerned. Zenith’s large scale production capabilities and short development periods assures consistent quality and faster deliveries.
Coated fabrics are flexible composite materials formed by applying bonding agents to either one or both sides of the fabric substrate and precisely coating it with different rubber compounds depending on the end application of the fabric. After the coating is cured it creates a strong bond between the rubber and the fabric. The final product after coating and curing is solid and flexible. It has a good stability and is washable, durable and much stronger than uncoated fabrics. Rubber coated fabrics are very close textured and therefore exhibit low permeation and diffusion. They can be electrically conductive and can also be weather, oil and temperature resistant. Zenith offers rubber-coated fabrics with special characteristics. We manufacture various types of fabrics for different applications such as barrier protection, abrasion resistance, air retention and high strength to weight ratios, flex resistance and resistance to chemical gases and fuels. Zenith uses basic fabrics such as Cotton, Nylon, Polyester, glass, knits, silk, Kevlar. Fabrics of various blends are coated with Nitrile, Chloroprene, Silicon, NR/SBR, Butyl, Hypalon (CSM), EPDM & blended polymers for variety of applications in the fields of Insulation, Defense, aviation, marine and offshore operations. ZRF fabrics are available from 0.3mm to 1.5mm thickness, 1.0 meter to 1.5 meter in width and in long lengths up to 100 meters. Zenith’s expertise in compounding is due to its extensive research and development program. All coated fabrics are vigorously tested for specification given by the customer. With our extensive testing procedures and fully equipped lab we ensure that all fabrics meet the highest quality standards. Zenith is using solvent-based coating, which gives better results as far as adhesion is concerned. Zenith’s large scale production capabilities and short development periods assures consistent quality and faster deliveries.
Coated fabrics are flexible composite materials formed by applying bonding agents to either one or both sides of the fabric substrate and precisely coating it with different rubber compounds depending on the end application of the fabric. After the coating is cured it creates a strong bond between the rubber and the fabric. The final product after coating and curing is solid and flexible. It has a good stability and is washable, durable and much stronger than uncoated fabrics. Rubber coated fabrics are very close textured and therefore exhibit low permeation and diffusion. They can be electrically conductive and can also be weather, oil and temperature resistant. Zenith offers rubber-coated fabrics with special characteristics. We manufacture various types of fabrics for different applications such as barrier protection, abrasion resistance, air retention and high strength to weight ratios, flex resistance and resistance to chemical gases and fuels. Zenith uses basic fabrics such as Cotton, Nylon, Polyester, glass, knits, silk, Kevlar. Fabrics of various blends are coated with Nitrile, Chloroprene, Silicon, NR/SBR, Butyl, Hypalon (CSM), EPDM & blended polymers for variety of applications in the fields of Insulation, Defense, aviation, marine and offshore operations. ZRF fabrics are available from 0.3mm to 1.5mm thickness, 1.0 meter to 1.5 meter in width and in long lengths up to 100 meters. Zenith’s expertise in compounding is due to its extensive research and development program. All coated fabrics are vigorously tested for specification given by the customer. With our extensive testing procedures and fully equipped lab we ensure that all fabrics meet the highest quality standards. Zenith is using solvent-based coating, which gives better results as far as adhesion is concerned. Zenith’s large scale production capabilities and short development periods assures consistent quality and faster deliveries.
Coated fabrics are flexible composite materials formed by applying bonding agents to either one or both sides of the fabric substrate and precisely coating it with different rubber compounds depending on the end application of the fabric. After the coating is cured it creates a strong bond between the rubber and the fabric. The final product after coating and curing is solid and flexible. It has a good stability and is washable, durable and much stronger than uncoated fabrics. Rubber coated fabrics are very close textured and therefore exhibit low permeation and diffusion. They can be electrically conductive and can also be weather, oil and temperature resistant. Zenith offers rubber-coated fabrics with special characteristics. We manufacture various types of fabrics for different applications such as barrier protection, abrasion resistance, air retention and high strength to weight ratios, flex resistance and resistance to chemical gases and fuels. Zenith uses basic fabrics such as Cotton, Nylon, Polyester, glass, knits, silk, Kevlar. Fabrics of various blends are coated with Nitrile, Chloroprene, Silicon, NR/SBR, Butyl, Hypalon (CSM), EPDM & blended polymers for variety of applications in the fields of Insulation, Defense, aviation, marine and offshore operations. ZRF fabrics are available from 0.3mm to 1.5mm thickness, 1.0 meter to 1.5 meter in width and in long lengths up to 100 meters. Zenith’s expertise in compounding is due to its extensive research and development program. All coated fabrics are vigorously tested for specification given by the customer. With our extensive testing procedures and fully equipped lab we ensure that all fabrics meet the highest quality standards. Zenith is using solvent-based coating, which gives better results as far as adhesion is concerned. Zenith’s large scale production capabilities and short development periods assures consistent quality and faster deliveries.
