WALL BIND ACRYLIC Cement Primer Water Thinnable No. Type WALL BIND Acrylic Interior Wall Primer (Water Thinnable) is suitable for useas a primer for painting of waterbased wall finishes such as distemper and plastic emulsions. 1 FEATURES WALL BIND has a special features are better whitness and opacity, easy brushing, excellent covering,alkali resistance,quick drying and good filling properties. Provides superior hiding and superior whiteness. 2 RECOMMENDED APPLICATION WALL BIND can be used for priming plastered wall,asbestose,brick work,cement concrete etc. PRODUCT TECHNICAL DATA No COLOURS White 1. FINISH Smooth and matt 2. COVERAGE 1 coat: 130-140 sq.ft/ltr 2 coats: 80-90 sq.ft/ltr (It may vary due to factors such as methods and conditions during application and surface roughness etc.) 3. DRYING TIME Surface drying time â?? 10-15 minutes 4. GLOSS LEVELS/SHEEN LEVELS NA 5. FLASH POINT (IS101/108 Part 1, Sec 9) Non- flammable 6. SUITABILITY OF THINNER PAINT Use within 24 hrs. 7. SHELF LIFE 12 Month from date of manufacture in original tightly closed containers away from direct sunlight and excessive heat. PERFORMANCE DATA 2. REMARKS a) Kindly refer to the MSDS for the saffro mellow coatings & resins Nano Acrylic Cement Primer which gives detailed information on Safety measures while handling the paint. b) Store the product at ambient conditions in well ventilate locations and away from the source of ignition and fire. c) Avoid eye and skin contact. In case of eye and skin contacts wash with plenty of clean water. d) Do not inhale or inject. In case of inhalation move to fresh air and seek medical attention. e) Use protective equipments like rubber/polythene gloves, safety goggle/glasses, face mask while handling. f) In humid areas, use of a bio-wash solution is recommended to remove surface fungus growth, fungal spores, mould etc. before application of the paint system. g) Do not apply when ambient temperature is less than 10�ºC or if the temperature might drop to this level within 4 hrs of application. h) Tinted paints need thorough shaking/mixing immediately after tinter addition as well as before use. i) For removing stains, sponge clean with a mild soap solution and wipe clean. Ensure drying time of 1 Week before cleaning.
ISO9809-3 150bar 37MN TUV TPED Oxygen Tanks Gas Cylinders 1 Minimum order quantity: 100 only 2 Use cylinders:Our seamless steel cylinders are widely used in industry, medical devices, fire fighting and scientific research Oxygen gas cylinders During the blanking process of gas cylinder production, the inner and outer surface and end face of the steel pipe shall be checked one by one, and the inner and outer surface of the billet shall not have cracks, serious pits, folds, folds, layers apart and scarring. The end face is smooth, no obvious burr, the inner and outer surface is clean, no feeding iron and debris, and check the perpendicularity and perpendicularity of the cylinder body one by one. This document (EN ISO 9809-3:2010) has been prepared by Technical Committee ISO/TC 58 Gas cylinders in collaboration with Technical Committee CEN/TC 23 Transportable gas cylinders, the secretariat of which is held by BSI TUV gas cylinders Interpretation of test results The interpretation of the burst test results shall involve: a) examination of the pressure/time curve or pressure/volume of water used curve, to permit determination of the pressure, py, at which plastic deformation of the cylinder commences, together with the bursting pressure ph; b) examination of the burst tear and of the shape of its edges. 150bar gas cylinders Product Information: 10.8 litres to 80 litres; 89mm-267mm cylinder outer diameter; Working pressure is 150bar; Hydrostatic test pressure is 250bar; 37 mn material; Iso9809-3 or GB/T5099.3 production standards; 2The minimum design wall thickness of gas cylinders is 2.4mm-6.2mm; The cylinder body weight is 1.60kg-72.4kg; The height of the cylinder body is 197mm-1520mm; Cylinder mouth threads include PZ19.2,PZ27.8,PZ39; 25E; 3/4-14 NGT, etc.; Maximum gas storage is 0.12m3-12m3 (150L-12000L) 3Aliases: Oxygen gas cylinders; Germany Rhein gas cylinder; 150 bar cylinder; Oxygen bomb; Gas cylinders 4A cylinder shall be considered to be of a new design, compared with an existing approved design, when at least one of the following applies: a) the nominal outside diameter has been changed; b) the guaranteed minimum thickness has been changed; c) the hydraulic test pressure, ph, has been increased (where a cylinder is to be used for lower pressure duty than that for which design approval has been given, it shall not be deemed to be a new design); d) the guaranteed minimum yield strength, Reg and/or the guaranteed minimum tensile strength, Rmg, have changed. Oxygen gas cylinders
DaFeng Prototype Co., Ltd is located in Dongguan City, which enjoys convenient transportation and high technology .We specialize in rapid prototyping, rapid tooling and low-volume manufacturing of custom parts. Our international team of engineers and technicians use advanced equipment and techniques like 3D printing,CNC machining,Vacuum casting and plastic injection molding, to turn your designs into reality quickly, accurately and at a great price.We can offer One-Stop-Shop from Design to mass production. We have more than 30 employees, including 5 members of the elite business team, 3 leading engineers, 8 CNC engineers, 10 craftsmen, 2 vacuum casting technicians, 3 spray painting and silkscreen printing experts, 3 surface treatment engineers, and other professional and technical personnel. We can offer you different prototypes,mockups,3D printing,rapid prototyping(SLA,SLS) of different products,such as medical products, consumer electronical products, household articles,auto-parts etc. Now we have advanced machines like CNC machining centers, 3D laser scanners, SLA modeling machines, vacuum forming machines, painting, silkscreen printing, electroplating, anodizing and other surface treatment facilities. These resources enable us to conduct small batch production and a large-scale injection model appearance on painting. We also can create and deliver 3D printing for rapid prototyping including the production of concept and presentation models from STL files. We can make everything into reality.Since we own the excellent clerks,advanced machines and rich experience, we can make everything. Most of our products are exported to different places in the world.Exporting takes over 90% of annual sales. The main countries and regions are: USA 20%, Europe 20%, Japan 15%, Korea 8%, South Aisa 8%, Oceania 15% and other 14%.All the products had been got favorable reputation from the customers. Contact us today and it will save you more time and cost. Contact us now Contact: Linda Email address:linda@jieruiprototype.com Phone:+86 13662899365 WeChat:13662899365 WhatsAPP:+8613662899365
DaFeng Prototype Co., Ltd is located in Dongguan City, which enjoys convenient transportation and high technology .We specialize in rapid prototyping, rapid tooling and low-volume manufacturing of custom parts. Our international team of engineers and technicians use advanced equipment and techniques like 3D printing,CNC machining,Vacuum casting and plastic injection molding, to turn your designs into reality quickly, accurately and at a great price.We can offer One-Stop-Shop from Design to mass production. We have more than 30 employees, including 5 members of the elite business team, 3 leading engineers, 8 CNC engineers, 10 craftsmen, 2 vacuum casting technicians, 3 spray painting and silkscreen printing experts, 3 surface treatment engineers, and other professional and technical personnel. We can offer you different prototypes,mockups,3D printing,rapid prototyping(SLA,SLS) of different products,such as medical products, consumer electronical products, household articles,auto-parts etc. Now we have advanced machines like CNC machining centers, 3D laser scanners, SLA modeling machines, vacuum forming machines, painting, silkscreen printing, electroplating, anodizing and other surface treatment facilities. These resources enable us to conduct small batch production and a large-scale injection model appearance on painting. We also can create and deliver 3D printing for rapid prototyping including the production of concept and presentation models from STL files. We can make everything into reality.Since we own the excellent clerks,advanced machines and rich experience, we can make everything. Most of our products are exported to different places in the world.Exporting takes over 90% of annual sales. The main countries and regions are: USA 20%, Europe 20%, Japan 15%, Korea 8%, South Aisa 8%, Oceania 15% and other 14%.All the products had been got favorable reputation from the customers. Contact us today and it will save you more time and cost. Contact us now Contact: Linda Email address:linda@jieruiprototype.com Phone:+86 13662899365 WeChat:13662899365 WhatsAPP:+8613662899365
BATTE Multicomponent Formula Loss-in-weight Feeder is applied for accurate bulk ingredient batching. This feeding system can be applied with every BATTE loss-in-wegiht feeder thanks to our special batch programs for the single and multi-feeder controllers. Techinical Parameter for BATTE Multicomponent Formula Loss-in-weight Feeder (LF Series) Main Components of BATTE Multicomponent Formula Loss-in-weight Feeder (LF Series) Working Principle of BATTE Multicomponent Formula Loss-in-weight Feeder (LF Series) This system measures the hopper weight when staring batch, and switch ingredient dispense off once reaching the fixed weight computed by the controller after the fixed batch has been entered. The Advantage of BATTE Multicomponent Formula Loss-in-weight Feeder (LF Series) Our feeder system adopts digital high resolution load cells, serial weight data transmission to the high-tech controller and special modes of approaching the fixed weight, all of which guarantee the high accuracy. Quality Control System Fixed Equipments for Q/C Qualified Adequately before Reaching Warehouse Randomly Checking Machines before Shipment Our Value-added Service Package 1. Installation Services: During the period of installation and debugging, we shall offer training about effective operation and maintenance. 2. Technical Services: Our company has been devoting ourselves into offering custom transforming projects for our worldwide clients in the field of medical, chemical engineering, plastics, rubber industries etc. We can assist our clients to solve all kind of technical problems with our capable technician team, and we own adequate experience for production line transformation as well as formula feeding arrangement. 3. Warranty Services: We offer free after sale service except the engineers' traveling expense for any quality problem occurs during our 12 months warranty period. Lead Time: 5-6 weeks after receiving the 30% prepayment. The attachment is some of our solution cases we provided for our clients, you can well refer to it. You are welcome to contact us in case you have any question or suggestion about our products or solution case.
Shockproof Sponge PORON Foam Tape Sheet Descriptions: PORON is a fine pitch open cell urethane foam produced by Rogers Corporation.The uniform, microcellular structure allows PORON to be easily compressed for dust seals and cushions. Water sealing with PORON is possible in applications with proper compression and moderate water exposure. The average cell size of PORON foam is approximately 100 microns. PORON cellular urethane foam was engineered to have excellent memory (compression set resistance). The compression set resistance of PORON makes it a top pick for sealing and cushioning electronics. PORON urethane foam is manufactured by continuously casting and curing mechanically mixed formulas to the desired thickness. PORON foam tape is using PORON foam as backing material and coated with one side or two sided different kinds of adhesives. Features: Low compression set - PORON cellular urethane has superior resistance to taking a compression set as compared to neoprene sponge or polyethylene foam. Less than 2% at 73°F and less than 10% at 158°F makes PORON an ideal gasketing material for many indoor enclosure applications where dust, light and incidental splash sealing are required. Energy absorbing - PORON's ability to absorb mechanical shock vibration combined with its low compression set make it an ideal material for shock isolation of battery compartments and sensitive electronics in hand-held devices. Consistent microcellular structure - Fine and consistent open cells make PORON microcellular urethane an ideal dust gasket material, suitable for many cleanroom applications. Adhesive backings - PORON readily accepts most of pressure sensitive adhesive offerings. Since PORON does not contain any plasticizers, it does not reduce adhesive shelf-life. The integral skin surface provides a clean, readily bonded surface. Thickness options - PORON is available in a wide range of thicknesses. Offers bonded layers to achieve non-standard thicknesses and stacked/bonded assemblies. Smooth skin - Most grades of PORON foam are manufactured with a smooth skin on both sides. The supported products have a 1 mil PET film bonded permanently to one side. Applications: Provide sealing and cushioning in thin displays, medical devices, electronic enclosures, and automotive and industrial applications. For Sealing, Gasketing, and Cushioning. OEM Size: Special length, thickness or combinations can be supplied per customer's request. Products can be supplied in roll, tape, sheets or shapes per customer's request. Only you provide the CAD drawing, we can die cut any size for you. Shelf Life: To obtain best performance, use this product within 12 months from date of delivery and store under normal conditions of 60 C to 80F (16 C to 27C) and 40 to 60% R.H. in the original carton.
Introduction This machine used for laminating cardboard with A/B/C/D/E/F flute or single, double & triple wall corrugated board & 450-700g/m²Grey board. PLC control system and frequency converter adopt Schneider electrical,adjust the relevant parameters automatically according to the paper size .control is stable and accurate. Automatic feed top sheet and bottom sheet,and pneumatic correction mechanism is used for feeding top sheet, feeding bottom sheet adopts servo motor control. Equipped with automatic oil supply lubrication system. Type: Gluing Machine Condition: New Application: Apparel, Beverage, Chemical, Commodity, Food, Machinery & Hardware, Medical, Textiles Packaging Type: Film, Steel pallet,Wooden box,Export standard Packaging Material: Metal, Plastic, Wood Automatic Grade: Automatic Driven Type: Electric Voltage: 380v Power: 15-17kw Speed: 90m/min Max. sheet size: 1700*1100mm Place of Origin: Zhejiang, China (Mainland) Brand Name: GUDE Model Number: GFM-1300/1450/1700Z Dimension(L*W*H): 1420*222/237/262*268cm Weight: 7000/8000/9000kg Color:Up to you Certification: CE ISO9001 After-sales Service Provided: Engineers available to service machinery overseas Warranty: 1 year Name:Laminating Machine Function: Laminating cardboard with corrugated board & Grey board Max. sheet size:1700*1100mm Min. sheet size:400*400mm Thickness of top cardboard:200-450g/m² Thickness of bottom corrugated board: More than 500g/ã?¡,less than 7mm HS CODE: 8479899990 Packaging & Delivery Packaging Details: Export wooden box or steel pallet Delivery Detail: Shipped in 30 days after payment Payment T/T L/C Paypal Western Union Certification CE,ISO9001 Service Warranty: 1 year After-sales Service : Engineers available to service machinery overseas Machines are new (or unused) and the guarantee period will be given thirteen months from shipment date. During this period, the seller will offer free maintenance and free spare parts that caused by the machineâ??s quality, but the buyer must pay the courier cost. Parts damaged because of mishandling and consumable parts are not covered by any warranty. -
3-ZONE THERMAL SHOCK CHAMBER Thermal Shock Test Chamber is used to test the capability of material structure or composite materials to withstand the continuous environmental changes between extremely high temperature and low temperature during a short time, and therefore understand the chemical changes or physical damages caused by expansion from heat and contraction from cold in the shortest possible time. It is applicable to metals, plastic, rubber, auto parts, chemical materials, electronics and other materials. The test results can be used as a reference or basis for product improvement. Working Principle This is so called three-zone type thermal shock test chamber. Sample is placed in the test chamber, more extreme temperature than test temperature can be set in high-temperature chamber and low-temperature chamber. When it comes to low temperature test, cold chamber door open, and low-temperature chamber working together with test chamber. When converted into high-temperature test, cold chamber door closed, hot chamber door are opened, and test chamber working together with high-temperature chamber. Conversion of mechanical action (transferring from high temperature to low temperature or low temperature to high temperature) can be completed in less than 1second, and the temperature can be quickly stabilized. During the whole test, test sample is no need to be moved, and without any human intervention. Applications 3-zone Thermal shock chamber have been designed to operate in accordance with reliability programs, quality control, commercial test programs and medical tests. It is used to test the capability of material structure or composite material to withstand the continuous environmental changes between extremely high temperature and low temperature during a short period. It is applicable to metals, plastic, rubber, electronics amongst other materials. The test result can be used as a reference or basis for produce improvement. Features 1.Thermal shork chamber in each zone for peak demand of heating and cooling. Provides extra thermal energy to efficiently meet the MIL-STD 883 requirements. 2.Temperature recorder provides 24 hour part temperature recording as the load travels from zone to zone. Using touch-control graph control as operation interface, easy to operate. 3.The system can be used for automatic Circulation Shock or manual selective shock, capable of setting two zones or three zones shocks as well as cold and thermal shock start-up. 4.Custom-made and optional accessories available. Standards Implement and Met GB/T 2443.1-2001 Test A: Low temp. Test; GB/T 2443.2-2001 Test B: Low temp. Test; GB/T 2443.22-2002 Test N: Low temp. Test; GJB 150.3-1986 High Temp. Test; GJB 150.4-1986 Low temp. Test; GJB 150.5-1986 Temp. Impact Test; (Load refer to 5.5.5 no active load)
aramid viscose fire retardant fabric Specialized in all kinds of protective workwear fabrics since 1998. We hope to establish a business relationship with customers from all over the world. aramid viscose fire retardant fabric 1.Product introduction of the aramid viscose fire retardant fabric The aramid viscose fire retardant fabric has wide applications,such as 2.Product parameter (Specification) of the aramid viscose fire retardant fabric Product name aramid viscose fire retardant fabric Material 50% meta-aramid 50% viscose Weight 200gsm Width 57/58" Structure Twill/Plain/Ripstop Color Black,navy,grey,light blue,etc Function flame retardant,antistatic,arc resistant,etc Usage Safety clothing Shrinkage â?¤±3% Color fastness 4-5 grade Abrasion Resistance 4-5 grade Certificate EN ISO 11611,EN ISO 11612 MOQ 1000 meters Service Quick Response,Lab dip,Test Report,Excellent Reception Payment T/T,L/C,Western Union,Paypal Packing plastic roll, inside with plastic bag, outside with woven bag 75m-100m /roll Sample Free sample available 3.Product Feature And Application of the aramid viscose fire retardant fabric permanent flame retardant,no melt,no drop,anti-static,arc resistant,alkali resistant,high tear and tensile strength,soft and comfort,fit for FR protective garments. 4. Production details of the aramid viscose fire retardant fabric 5. Product Qualification of the aramid viscose fire retardant fabric Aramid viscose fire retardant fabric can meet EN ISO 11611 ,EN ISO 11612. Our fabrics are certificated by ASTM,EN,NFPA,UL,etc and are very popular in European and American Market. 6. Deliver,shipping and Serving of the aramid viscose fire retardant fabric. We promise to finish the production and deliver the cargo on time,track the cargo transition,and tell customer the pick-up time.We are glad to answer customers questions and provide technical guidance free.Also well recommend new products for our customers.
Description Silo body constructed with hot-galvanized corrugated steel plate;zn-coat thickness 275g per square meter. Silo body is 1250mm wide,fit for different thickness requirements(1.0-1.5mm) All steel plate joints are fixed by Grade8.8,M10 bolt and seal gums,ensuring no leaking seams,security and long operating life Transparent viewing w indow Transparent viewing window is good for observing feed delivery condition in the silo clearly. Use high strength plastic fastened strongly and sealed. Non-friable more secure and durable Automatic torsion spring controlling With our special automatic torsion spring controlling and steel wire rope design, customers can easily open and close stainless steelroof cover on the ground. Optional anti-block ball is available as per your requirement to convey feed flow more smoothly. Transparent feed opening Use high strength plastic fastened strongly and sealed Non-friable more secure and durable Introduction and Advantages: 1. The hopper bottom steel silo series is specially designed by senior engineers in our company, with high-quality galvanizing board. 2. Hopper angles can be 45° and 60°,among which 60° conical bottom is usually used to store larger pellet and powder materials with high viscosity. 3. All BODA silos are precision engineered from high strength, 80mm x 14mm low profile corrugated steel plate, galvanized to 275 g/m2 (or optional 450 g/m2). 4. Lower basic cost with lightweight, low request for foundation, low consumption of steel. 5. High degree of standardization. We can produce the standard components which can be installed on-the-spot. Simple, easy and efficient to install within a short amount of time due to superior component design which are connected by standard bolts. 6. Easy to maintain. As the parts of the silo are connected by standard bolts, so it is easy to remove or repair it. 7. The life cycle of the silos can come up to 30-50 years long. The products are designed comply with the national standard of GB50322-2001. WZH feed tower chicken farm cosists of silo body sheets, silo lid, collar, hopper sheets, roof panels, silo legs, ladder system. All parts are manufactured to engineering design specifications and quality checked to ensure hassle-free assembly and use Features of Feed silo As a professional manufacturer of storage equipment, we have developed, designed and manufactured assembly steel silos The standard ladder and fence is safe and reliable. The feed bin is fastened strongly and sealed. Our feed bin made by high quality galvanized steel sheet. Bin lever indicators at bottom and roof
Butyl sealant is a kind of environmental friendly, non solidified self adhesive sealant. It can maintain its plastic and sealing properties without crack and harden in a wide temperature range. What's more, its excellent weather resistance, acid and alkali resistance, good air tightness and electrical insulation properties make it have good adhesion to glass, aluminum alloy, galvanized steel, stainless steel and other materials. And due to its extremely low water vapor transmission rate, butyl sealant with elastic sealant together can form an excellent anti moisture system. Butyl sealant is applicable for all kinds of machinery, pipe, glass installation, cable joints and other seals as well as buildings, water conservancy projects, etc. Specifications: Product name: butyl sealant. Material: isobutene polymer and butyl rubber blending. Color: black. Specific Gravity (g/m3): 1.10-1.30 g/m3. Operating temperature: -20 °C- 80 °C. Temperature resistant range: -40 °C - 130 °C. Maximum temperature bearable: 160 °C. Water vapor transmission rate: < 0.01 g/m2 per day. Solids content: 100%. Hot weightlessness: 0.1%. Shearing strength: 0.13 Mpa. Storage condition: -10 °C - 35 °C, in a cool, dry and ventilated place. Storage period: 12 months. Transportation: Butyl sealant is non dangerous, so it is suitable for all kinds of transport such as truck, train, boat and plane, etc. Note: When butyl sealant matches use with other rubber, compatibility test should be done. Features: Heat resistance. Strong adhesion. High air tightness. Weather resistance. Electrical insulation. Excellent sealing effect. Excellent UV resistance. Acid and alkali resistance. Can be reused and no waste. Environmental friendly material. Extremely low water vapor transmission rate. No solvent, no fog, non vulcanization, with permanent plasticity. need no curing period, saving floor area. (1 minute curing time). Applications: Butyl sealant is applicable for the building doors and windows glass, curtain wall, refrigerator, freezer, train and car, etc.
Salt is the common name for the compound, composed of crystalline mineral called rock salt or halite. Salt with a chemical name of Sodium Chloride and formula NaCl, belongs to the large class of salt. It is presented in huge quantities in seawater & it is the main mineral component of the sea. Sodium chloride is a mineral which plays a vital role for humans and animal health and therefore is used in several industries. By evaporating mineral rich seawater in the shallow pool and by processing it in the mines, various grades of salts are formed, further which can be processed. Salt is huge quantity is been used in production of other chemicals such as baking soda (sodium bicarbonate), caustic soda (sodium hydroxide), chlorine, hydrochloric acid and many more chemicals. It is used for several other industrial applications such as in manufacturing of paper pulp, polyvinyl chloride, plastics and in processes like de-icing highways, water conditioning and even for agricultural use. Salt is basic food items for humans too and plays essential role in human health as an electrolyte. We use it as an anti-caking agent and to prevent iodine deficiency. It is also employed in soap and enamel manufacturing, in Pharmaceutical, Oil Drilling and Gas Industry and helps into metallurgical processes of fusing the metals. Therefore, our provided Salt has adequate Iodine and low sodium content to enriched Normal growth and development. Jyoti Chemical provides you with all types and grades of Salts from Triple Refined Edible Iodized Salt to Industrial & Refined Industrial Non Iodized Salt and Any Other Customized Required Salt at the lowest price.
Salt is the common name for the compound, composed of crystalline mineral called Rock Salt or Halite. Salt with a chemical name of Sodium Chloride and formula NaCl, belongs to the large class of Salt. It is presented in huge quantities in seawater & it is the main mineral component of the sea. Sodium Chloride is a mineral which plays a vital role for humans and animal health and therefore is used in several industries. By evaporating mineral rich seawater in the shallow pool and by processing it in the mines, various grades of salts are formed, further which can be processed. Salt is huge quantity is been used in production of other chemicals such as Baking Soda (Sodium Bicarbonate), Caustic Soda (Sodium Hydroxide), Chlorine, Hydrochloric Acid and many more chemicals. It is used for several other industrial applications such as in manufacturing of Paper Pulp, Polyvinyl Chloride, Plastics and in processes like de-icing highways, water conditioning and even for agricultural use. Salt is basic food items for humans too and plays essential role in human health as an electrolyte. We use it as an anti-caking agent and to prevent iodine deficiency. It is also employed in soap and enamel manufacturing, in Pharmaceutical, Oil Drilling and Gas Industry and helps into metallurgical processes of fusing the metals. Therefore, our provided Salt has adequate Iodine and low sodium content to enriched Normal growth and development. Jyoti Chemical provides you with all types and grades of Salts from Triple Refined Edible Iodized Salt to Industrial & Refined Industrial Non Iodized Salt and any other customized required Salt at the lowest price.
5052 aluminum plate is an AL-Mg alloy aluminum plate, which combines the advantages of 3 series anti-rust aluminum and the excellent formability of 5 series. It has moderate strength, especially fatigue resistance: high plasticity and corrosion resistance, cannot be strengthened by heat treatment, and is durable. Good corrosion, good weldability, poor machinability, can be polished. Application areas: transportation vehicles, ship sheet metal parts, aircraft fuel tanks, etc. 5083 aluminum plate belongs to the Al-Mg series alloy and is widely used. Especially in the construction industry, this alloy is inseparable and it is a promising alloy. It has good corrosion resistance, excellent weldability, good cold workability, and medium strength. Application fields: ships, automobiles, aircraft welding parts, subway and light rail, etc. 5754 aluminum coil is a typical aluminum plate among Al-Mg alloys. It has the characteristics of medium strength, good corrosion resistance, weldability and easy processing and forming. Application areas: automobile manufacturing industry, doors, bodies, seals, etc. 5182 aluminum plate has good corrosion resistance, excellent weldability, good cold workability, and medium strength. Application areas: automobile body panels, control panels, reinforcements, automobile fuel tanks, electrical appliance casings, etc. Status: O, H32, H34, H36, H38, H111, H112 Surface treatment: smooth aluminum, mirror, patterned aluminum plate Packaging and transportation: simple packaging, refined packaging, logistics packaging, foreign trade shipping packaging (fumigated wooden pallet optional) Please contact us for specific parameters and we will give you a detailed quotation.
One-time forming, adopting advanced technology from Germany, Korea and Italy, Perfect connection polyester yarn by high technology, Environment friendly raw materials /free of industrial waste. UV provides long lasting life, Decreases stretching when exposed to pressure. PVC Lay-flat hose is a tough water discharge hoses made with a PVC cover and reinforced polyester yarn. The high-tensile polyester yarn provides great durability and strength in all working situations. it is highly durable while maintaining great flexibility and best suited for low medium pressure applications. Application: PVC layflat hose is designed for light and heavy duty applications, the hoses are most commonly used in agricultural equipment where continuous water flow through irrigation systems is required. Additional uses include water pump, pool & spa, construction, mines and marine.For suck or discharge large flow air, water, dust, mud, or chemical solvent for agriculture irrigation, industrial water, construction, hardware, garden tools, etc. Our lay flat hose, made from PVC and reinforced with high-strength polyester fiber, offers numerous benefits over other types of hoses or water pipes. Because of the flat design, it's easily stored and moved from one area to another, and its flexibility allows for easy manipulation. This is one reason why our blue layflat hose is typically used as a supply line for connecting fire engines to hydrants. It's equally useful when used for irrigation, wastewater or sump pump discharge. This lay flat discharge hose is strong, durable and corrosion resistant. It's a popular choice for use in drip irrigating gardens as this hose can be easily pierced to provide drip holes. Construction: Tube: Extrude industrial grade PVC. Reinforcement: Reinforced with polyester yarn. Color available:black, grey, blue, yellow, red, etc Material: high strength polyester filament and high quality PVC. One step extrusion: Parted the threads regularly and molded by plastic coated once. Character: Acid & alkali resistant . aging resistant, stretching resistant, anti-wrinkle, non-toxic. Temperature range: -5C to +65 C
Superior corrosion resistance, Extensive range of chemical resistance, Non-contaminating, smooth surface, Lower sediment accumulation, Not UV resistant, Non-conductive, strong pressure bearing capability, Easily installed with cement or clamp Easy to handle & install This Crystal clear PVC hose Constructions: Non-toxic & crystal clear Heavy wall is kink resistant Chemical & ozone resistant Burst pressure is 3 times the working pressure Self-extinguishing Temperature: -10 (-50) to 65(+150) Application: PVC transparent hose is used for conveying water, oil, gas under normal working condition in factories, farm, ship, building and family. Characteristics: Flexible, light, transparent.Food grade, non-toxic, without odor.Anti-erosion and anti-abrasion.Anti-aging,long working life.PVC Clear Heavy Duty General Service Hose is designed for transfer of abrasives, air, food particulates, sanitary products and potable water in applications.This general purpose PVC CLEAR HOSE PIPE TUBE is the industry standard for air and water applications. HOSE is clear, so you can easily monitor flow. It is flexible to easily bend around objects.This PVC clear hose is more economical. Clear PVC Hose pipe provides a versatile, cost-effective alternative for many hose piping applications, particularly those where visual monitoring is critical. The benefits of transparent plastics are well recognized. Clear PVC Hose pipe has exceptional corrosion resistance; smooth interior walls for unimpeded flow and reduced sediment buildup; non-contaminating for purity applications; fast, reliable solvent-welded connections; good pressure-bearing capability; and ease of handling and installation, to name a few. All of these important benefits are now available in a unique product with optimum clarity. This clarity provides the all-round visibility that specialized applications demand whether it be clean room applications, sight glass, dual-containment or various other processing applications where continuous monitoring is necessary. Simple solvent-welded joining techniques.Fully compatible with standard PVC hose pipe, fittings and valves.Corrosion resistant, Non-conductive.Resists bacterial and biological activity.Lower overall cost and longevity than other alternatives such as acrylic pipe.
ZB1401-25 Name External Eye End Material stainless steel 316 Suface finish high polishing MOQ 1 PC Technqiue investment casting Packing bubble bag+ carton Brand Richwits Speficication of SS External Eye End This External Eye End is casted in stainless steel 316 material by investment casting, which is solid and durable The surface is polished . Good material and excellent polishing quality make it has good performance on anti-rust and corrosion resistance . The screw here make the connection with pipe tightly.Two sizes available , which can fit tube 7/8 in or 1 inch. Zhibo is a professional manufacturer of stainless steel marine hardware and rigging hardware. In our factory , you can get anchors, hinges , deck fillers, fishing rod holders , eye plates , eye botls, shackles , turnbuckles, thimbles, carabiners and soon. Most of them can be supplied from stock. Low MOQ is acceptable. Contact us now for more details! Bimini Top Fitting stainless steel Swivel Deck Hinge Boat Deck Hinge 90 Degree Pin Marine Hardware boat hardware Key Features: - Fine polished & well-plated bimini top fittings; - 7/8'' ID external eye end, fit for most 7/8'' OD round tubing; - Corrosion resistance, solid, withstand harsh weather conditions; - Heavy duty 316 stainless steel for marine & industrial applications; - Perfect replacement parts for worn-out, plastic, nylon fittings; - Work with jaw slide to join the bimini top frame; - Easy to assemble and install; Specification: Material: 316 Stainless steel Internal Diameter: 22.6mm (7/8 in) Outside Diameter: 27.7mm (1 in) Thickness: 2.58mm (0.1 in); Height: 54.5mm (2.15 in) Mounts: 1/4'' bolt holes
Perimeter Intrusion Detection System The RF900 is a Dual-zone perimeter intrusion detection system designed to detect intrusions into the perimeters and borders on the basis of the principle of M-Z laser interference. It adopts optical fiber vibration sensing technology, to detect and notify any intrusion attempt such as climbing, cutting sabotage the fence or disassembles the system.The device has only one defense area and is available without external communication network. The project construction is convenient, no network transmission cable is required, the equipment can be managed and monitored remotely, with built-in battery. When the equipment is powered off, it can indicate the power off alarm, and ensure the normal operation of the equipment to achieve 24-hour uninterrupted protection. Furthermore, it has strong anti-disturb ability to eliminate environment nuisance alarms and can be immune to electromagnetic interference, lightning and storms. The RF900 perimeter intrusion detection system provides both indoor and outdoor deployment, supports 1-2 defense zones; it is suitable for villas, residential, oil depots and other short-distance or less complex perimeter protection. Features Zone length is up to 500m. One zone and two zones are optional. Optical fiber length is up to 1000m. Use normal optical fiber cable for telecommunications (GYXTW). Fiber optics can be installed on wire net or underground. Support contact closure alarm output. Detect behaviors of climbing, cutting, sabotage and disassembling. Support rapid fiber cutting detection (less than 1 second). Be immune to electromagnetic interference, lightning damage. ESD and surge protection circuits inside. Ambient working temperature: -40 ~ +70 Adopt ABS engineering plastics. DC12V power supply with consumption less than 3W. Application RF900 Dual-zone GPRS intrusion detection system You can find more information on our web, so please take a look.
Essential details Finish: ZINC, Plain, Zinc,Plain,Blue,Dyed Material: Stainless steel, Steel, Stainless steel,Steel,Brass,Aluminium, Titanium Model Number: Phillips Socket Cheese Head Machine Screws Standard: DIN, DIN Grade: 4.8/6.8/8.8/10.9/12.9 Package: Iner Plastic Bag + Carton + Pallet Delivery time: 5-15 Days Head type: Pan, Truss, Flat, Oval, Round, HEX, Cheese, Binding Certificate: ISO9001:2008 Product name: Phillips Socket Cheese Head Machine Screws a manufacturer of fastener, has been supplying non-standard and custom made screw since 2002. According sample or drawing requirements, provide one-stop custom services to solving your custom screw needs. King-Tower is committed to offering you the widest range of sems screw, anti-theft screw, thread-locking screw and stainless steel screw and more. If you have any fastening inquiries, our engineering department will be glad to help with our many custom screw options. Q1. why should you buy from us not from other suppliers A1:1.Our company has passed IATF16949:2016quality system certification; 2.We have 11 years experience in screws production; 3.We can provide the OEM&ODM serve. Q2. What is the advantage about your company A2.Our company has professional team(ten engineer with 11 years experience) and professional production line(more than 200 sets of precision equipment ). Q3. Why should I choose your products A3. Our products are high quality and competitive price; Q4. The logo and the color can be customized A4.Yes,we can custom the logo and color,accroding to your requirements. Q5. Any other good service your company can provide A5. We can provide better after-sale and faster delivery.
Overview Essential details Finish: ZINC, Plain, Zinc,Plain,Blue,Dyed Material: Stainless steel, Steel, Stainless steel,Steel,Brass,Aluminium, Titanium Model Number: Set screw Standard: DIN, DIN Grade: 4.8/6.8/8.8/10.9/12.9 Package: Iner Plastic Bag + Carton + Pallet Delivery time: 5-15 Days Head type: Pan, Truss, Flat, Oval, Round, HEX, Cheese, Binding Certificate: ISO9001:2008 Product name: Stove Shaft Set Bolt a manufacturer of fastener, has been supplying non-standard and custom made screw since 2002. According sample or drawing requirements, provide one-stop custom services to solving your custom screw needs. King-Tower is committed to offering you the widest range of sems screw, anti-theft screw, thread-locking screw and stainless steel screw and more. If you have any fastening inquiries, our engineering department will be glad to help with our many custom screw options. FAQ Q1. why should you buy from us not from other suppliers A1:1.Our company has passed IATF16949:2016quality system certification; 2.We have 11 years experience in screws production; 3.We can provide the OEM&ODM serve. Q2. What is the advantage about your company A2.Our company has professional team(ten engineer with 11 years experience) and professional production line(more than 200 sets of precision equipment ). Q3. Why should I choose your products A3. Our products are high quality and competitive price; Q4. The logo and the color can be customized A4.Yes,we can custom the logo and color,accroding to your requirements. Q5. Any other good service your company can provide A5. We can provide better after-sale and faster delivery.