Pvc Sound Proof Tarpaulin Material Suppliers and Manufacturers

This is chemical setting Furan based chemical resistant mortar which is combination of Liquid and Powder, when mixed in proper proportion from workable mortar which after setting and curing give of liquid and give black highly cross linked composites. Furan When set and cured is resistant to highly corrosive acids, alkalis and to powerful organic solvents such as ketones, Aromatic and Chlorinated solvents. It has extreme resistant to Acidic & alkalis, Salts, Greases and Detergents. It resists to Organic & Inorganic acids at their boiling temperature. It is suitable against mild chlorine Gas (dry) phosphorous trichloride, pyridine at room temperature. Furan is especially useful where resistance to mixed media such as aqueous acids /alkalis and organic solvents is needed in chemical plant process and waste streams. Carbon filled Furan is used against corrosive effect of hydrofluoric acid & its salts. PREPARATION OF FURANE MORTAR : Mortar consist of Furan solution and Furan powder. The average mixing ratio necessary to obtain mortar with good working consistency is 1 part by weight Solution & 3 part by weight powder. The ratio will vary slightly depending on temperature and working conditions.Stir the liquid thoroughly before using. Place liquid in a suitable shallow mixing pan. Add powder by weight in the solution mix thoroughly and rapidly until all lumps are dispersed and the mortar is completely homogenous. Spread out the mortar in a thin layer, not more than ¾ thick, to dissipate the heat of reaction and lengthen the working life. Batch size can be varied depending upon the temperature and the speed with which the masons are working. Very large batches will become stiff quite rapidly. Make sure that all the Furan Motrar is used from the pan before another batch is mixed.When working at temperature above 40 C, very small batches not more than 2 Kgs, should be prepared. When working at temperature below 15C the liquid should be kept warm.

DATA SHEET FOR EPOXY EPOXY COATING :- INTRODUCTION - EPOXY COATING (HYB) is a two part high solids solvent free epoxy phenolic resin based coating system designed for hard wearing, smooth surface finish for floors, walls and on steel structures. Nonskid surface finish can be achieved on floor, if required. FEATURES: 1) Hard Wearing 2) Non Dusting 3) Excellent Surface Finish 4) Non Smelling 5) Good Aesthetics 6) Highly Chemical Resistant APPLICATION: 1.Stir well before mixing Part A and Part B and mix in the prescribed ratio. 2.Apply one coat of EPOXY primer on the clean and dry surface. 3.EPOXY COATING (HYB) should be applied on the surface by brush or roller within 24 hrs. After application of primer coat it should be allowed to air dry for min. 4 hrs. Preferable in a dust free atmosphere. 4.Apply min. 2 coats with the intercoat interval of 6-8 hrs. PRODUCT SPECIFICATIONS: Application - Brush, Roller Mixing Ratio - As Directed on Packing Port Life - 30 Mins. Drying Time - Touch Dry- 30 Min, Hard Dry 6 Hrs. - Intercoat Interval 6-8 Hrs. Min. - Dry Film Thickness 125-150 Microns/per coat - depending on porosity Covering Capacity - 6-8 sq.met/kg per coat depending on porosity, roughness & method of application. Color Shades - All Standard Shades RECOMMENDED USES: 1) Food & Pharmaceutical 2) Work Shop 3) Clean Room Application 4) Chemical Resistant Coating for Concrete& Steel 5) Petrochemical, Fertilizer plants METHOD OF APPLICATION: SURFACE PREPARATION The long-term durability of the applied Epoxy coating (HYB) epoxy coating is dependent on the adhesion between sub-base and coating material. It is most important therefore, that the substrate surfaces are correctly prepared prior to application. 1.Before application of the Epoxy coating (HYB) surface should be free from loose partials, rust, oils, grease or earlier coatings and should be totally dry. 2.New concrete or cementations surface should be placed at least 28 days and have a moisture content of less than 5% before application of Epoxy coating (HYB) 3.After surface is dry, all repair work like sealing of joints, cracks filling of cavities and crevices should be carried out. HEALTH & SAFETY - Keep the containers tightly closed when not in use. Avoid contact with skin & eyes. It comes in contact with the body, wash affected parts with plenty of water and contact a doctor. Other known sector for Epoxy floor lining, Epoxy garage floor lining, Concrete epoxy lining, Concrete floor epoxy lining, Epoxy pipe lining, Marine epoxy lining, Sub marine epoxy lining, Basement lining epoxy floor shield, Louisiana, Oregon, Chip lining color epoxy floor, Aviation lining epoxy interior.

Bitumen Primer * Bitumen Primer is Bituminous air curing ready mixed Acid & Alkali resistant special primer. Application * Concrete surface must be clean, dry and rough. No primer should be applied over smooth and wet surface. * After cleaning the concrete surface, one coat of Bitumen Primer should be applied with brush and allow to dry thoroughly. * The drying time will depend upon the temperature. * 24 Month at the temperature 30C (+2OC) Packing * Bitumen Primer: 25 Liter Drum Note * Bitumen Primer contains volatile and slightly toxic solvent. Keep away from spark and open flames at working area. * Bitumen premier it is manufactured using bitumen solution which is used for sealing of prime porous and non-porous surface, and also to protect residential and commercial building. * Bitumen Primer is used to protect substrate against corrosive attack, is suggested to apply anti-corrosive primer.It is best for protection against sub-striate against atmospheric corrosion and chemical corrosion. It is a mixed substance made up of organic liquids that are highly sticky, water proof, viscous,acid proof as with all surface coating, good Bitumen Premier is used for long life of the system. it is applied by brush or roller and allowed to dry before any water proofing treatment so to avoid solvent it is used in defects such as cracks, broken mortar joints, etc. are to be repaired prior to Bitumen primer application. Product Details: Grade Standard Technical Grade Physical State - Liquid Usage - Industrial Color - Black Characteristics: Appearance/Color - Pasty liquid/ black Chemical Base - Bituminous rubber emulsion. Density - 1.0 kg/l Curing Speed/ Rate - 3 - 4 hours Tack free after - 5 - 10 hours Cured after - 2 - 4 days (Dependent on ambient Solid Content by - temperature, substrate temperature, Weight - relative Water Content by weight - humidity and thickness of the coating) Bitumen Content - 41% by weight - Thixotropic (The viscosity can be adjusted by - Viscosity adding up to max. 5% of clean water. - Stir well prior use) - For light protection: 1.0 mm min. Coating - For greater protection: ~ 1.5 - 2.0 mm Thickness applied - in two coats. Water Penetration - 48 h, 1 bar: 78.5 cm2: 0 ml under Hydrostatic - 96 h, 4 bar: 78.5 cm2: 33 ml Pressure - Water vapor 6 x 10-7 mg / hmPa Permeability Service - -30 C to 200 C Temperature - Adhesion Concrete - Very good, Timber: Very good, Metal: Moderate Glass: Poor

PRODUCT DATA SHEET ACID RESISTANT BRICK Material : RED SHALE Type Acid Resistant Brick Size (mm) 230 (LENGTH) X 115 (WIDTH) X 100,76,65,50,40,38,30,25 (THICK) Specification : ASTM C279, ASTM C410, IS 4860-1982 DESCRIPTION : We offer premium quality acid resistant bricks Red â?? Shale , tiles and special shapes. We also offer customized sizes as per clients' requirements. Our acid bricks comply with ASTM C279 Type-III, ASTM C410 Type H, L, and Indian Standard 4860 - 1982 Class-I for all applications where low absorption and high acid resistance is required. FEATURES OF ACID RESISTANT BRICK: Excellent resistant against wide range of chemicals except hydrofluoric acid, high abrasion resistance, low wearing properties, High Thermal resistant to sudden change in temperature AREA OF APPLICATION: Chemical Analysis (Average) Acid and Alkali Storage Tank Farms Demineralization plants and Water treatment plants Chimney inside lining, FGD linings Towers and Columns Process Vessels and Tanks Sewerage Treatment Plants and Lines Industrial Flooring and Bund Areas Chimney and Flue Gas Linings Hoppers and Chutes SiO266.4 Al2 0324 TiO21.1 Fe2 O31.1 K2 O + Na2 O2.5 NOT RECOMMENDED: HF acid or other fluoride solutions Heavy thermal shock Typical Physical Properties of GANESHAS Acid and Chemical Resistant Brick Characteristic RED SHALE ACID RESISTANT BRICK Test Standard Bulk Density, gm/cc - 2.3 to 2.35 ASTM C-20 -Water Absorption, % - 0.1 to 1.5 IS 4860-1968 Apparent Porosity, % -0.5 to 1.75 S 4860 Acid Solubility (H2SO4), Loss in Mass,% -0.1 to 1.8 ASTM C-279 Modulus of Rupture, PSI -2133 to 3555 ASTM C-67 Compressive Strength, Kg/cm2 - 700-900 IS 4860-1968 Abrasion Resistant , Volume in mm3 -69 to 85 EN 102 Surface Hardness, MOHS Scale - 7

PRODUCT DATA SHEET ACID RESISTANT BRICK Material : FIRECLAY Type Acid Resistant Brick Size (mm) : 230 (LENGTH) X 115 (WIDTH) X 100,76,65,50,40,38,30,25 (THICK) Specification : ASTM C279, ASTM C410, IS 4860-1982 DESCRIPTION : * We offer premium quality acid resistant bricks Red â?? Shale , tiles and special shapes. We also offer customized sizes as per clients' requirements. Our acid bricks comply with ASTM C279 Type-III, ASTM C410 Type H, L, and Indian Standard 4860 - 1982 Class-I for all applications where low absorption and high acid resistance is required. FEATURES OF ACID RESISTANT BRICK: * Excellent resistant against wide range of chemicals except hydrofluoric acid, high abrasion resistance, low wearing properties, High Thermal resistant to sudden change in temperature AREA OF APPLICATION: Chemical Analysis (Average) Acid and Alkali Storage Tank Farms Demineralization plants and Water treatment plants Chimney inside lining, FGD linings Towers and Columns Process Vessels and Tanks Sewerage Treatment Plants and Lines Industrial Flooring and Bund Areas Chimney and Flue Gas Linings Hoppers and Chutes SiO266.4 Al2 0324 TiO21.1 Fe2 O31.1 K2 O + Na2 O2.5 NOT RECOMMENDED: HF acid or other fluoride solutions - Heavy thermal shock Characteristic Fireclay Type Acid Resistant Brick - Test Standard Bulk Density, lbs/ft3 - 2.25 to 2.30 ASTM C-20 Water Absorption, % - 0.1 to 1.8 ASTM C-20 Apparent Porosity, % - 4.05 to 4.14 ASTM C-20 Acid Solubility (H2SO4), Loss in Mass,% - 6.1 to 6.8 ASTM C-279 Modulus of Rupture, Mpa - 14.6 ASTM C-67 Compressive Strength, PSI - 15500 to 17250 ASTM C-67 Abrasion Resistant , Volume in mm3 - 71 to 96 EN 102 Surface Hardness, MOHS Scale - 7 Thermal Conductivity, BTU-in/hr-ft-F - 6.94 to 7.12 ASTM C-236 Thermal Expansion Coefficient,in/in/Fx10-6 - 2.6 to 2.8 EN 103

Acid / Alkali Resistant Tiles/Bricks * Our Acid proof tiles, Acid alkali resistant tiles, Chemical resistant tiles are fully vitrified tiles which are manufactured using special non ferrous clay, processed at extremely high temperatures this process causes the raw materials to fuse and form a compact mass with an extremely low water absorption of less than 0.5% resulting in the formation of a very strong body with a flexural strength of 38 N/mm2, solid through color fade proof with a very hard surface Mohs hardness of 7. * The acid resistant tiles come in a range of sizes and thicknesses from ranging from 8-25mm. Our acid proof tiles meet stringent specification norms of IS 4457:2007 and relevant ASTM/DIN standards which ensure excellent performance in Acid/Alkali/Chemical (expect Hydrofluoric acid and its derivatives). Corrosion Protection Applications * Factory Floors subject to corrosion from Chemicals, Acids, Oil & Solvents * Pickling tank and surrounding areas * Food & Beverage Industry flooring * Battery rooms and Control rooms * Demineralization plants * Walls of washing and Paint shop areas * Acid Resistant Tiles Manufacturers India * Our acid proof tiles provide excellent abrasion resistance, anti-skid properties for worker safety and high aesthetic appeal. We also provide specialized corner tiles for reducing chances for acid attack through construction joints. Our standard sizes are 200x100, 200x200 & 300x300 millimeters.

Type: Chopping Blocks Commercial Buyer: Restaurants, Food & Beverage Stores, Food & Beverage Manufacture, Department Stores Season: Everyday Room Space: Kitchen, Dining Room Design Style: Modern Material: Bamboo/Wooden Feature: Sustainable Place of Origin: Vietnam Brand Name: 99 GOLD DATA Model Number: Selena +84 587 176 063 Product name: Cutting Board Usage: Kitchenware Color: Customized Color Keyword: Custom Chopping Board Function: Cutting Food Board MOQ: 1000pcs OEM & ODM: Accepptable High Quality: 100% Eco-friendly Description: Chopping Cutting Board Blocks PAYMENT: TT 30% Deposit Supply Ability 20000 Piece/Pieces per Month Packaging Details Poly bag;Shrink package;White box;Color box;PVC box;PDQ display box Port All port in Vietnam

ITO GLOBAL, SALE OFFER ZINC ASH ,Product: Furnace Plant Material Zinc Ash, 35-40% basis. Origin: INDIA Quantity: 500 t Trial; 10,00 ton per month thereafter with possibility to increase. Contract Period: 12 Months. PAYMENT TERMS: Letter of Credit 100% LC Confirmed and Irrevocable, Non-Transferable and Indivisible. Payable At Sight at the Port of Loading against boarding documents. PERFORMANCE BOND: 2% Performance Bond to be issued by Seller to Buyer on issue of DLC. DELIVERY CONDITIONS (INCOTERMS): FOB INDIA or CIF AWSP Buyer choice PACKAGING: Bulk. Shipments are initiated 30 days after confirmed DLC. PROCEDURES: 1. Seller issues FCO. 2. Buyer signs FCO on acceptance and submits ICPO / LOI. 3. Buyer returns signed and stamped FCO. 4. Seller issues Contract with full banking details. 5. Buyer and Seller sign and exchange contracts. 6. Seller provides Proof of Product &/or Buyer conducts a site Visit to verify goods and local conditions. 7. Buyer's Bank opens Letter of Credit. 8. Shipment commences as per contract.

ITO GLOBAL, SALE OFFER ZINC ASH / EAF DUST ,Product: Furnace Plant Material Zinc Ash, 35-40% AND 40-45% basis. Origin: INDIA Quantity: 100 ton Trial; 1000 ton per month thereafter with possibility to increase. Contract Period: 12 Months. PAYMENT TERMS: Letter of Credit 100% LC Confirmed and Irrevocable, Non-Transferable and Indivisible. Payable At Sight at the Port of Loading against boarding documents. PERFORMANCE BOND: 2% Performance Bond to be issued by Seller to Buyer on issue of DLC. DELIVERY CONDITIONS (INCOTERMS): FOB INDIA or CIF AWSP Buyer choice PACKAGING: Bulk. Shipments are initiated 30 days after confirmed DLC. PROCEDURES: 1. Seller issues FCO. 2. Buyer signs FCO on acceptance and submits ICPO / LOI. 3. Buyer returns signed and stamped FCO. 4. Seller issues Contract with full banking details. 5. Buyer and Seller sign and exchange contracts. 6. Seller provides Proof of Product &/or Buyer conducts a site Visit to verify goods and local conditions. 7. Buyer's Bank opens Letter of Credit. 8. Shipment commences as per contract.

2Lians can supply PVC product as below: PVC Regrind Mixed Color Plastic Scrap for Recycle MATERIAL: PVC regrind mixed color CATEGORY: PVC TYPE: Regrind GRADE: Mixed color SPECIFICATION: From Pipe Origin: Japan LOADING WEIGHT: 24 Tons

PVC Agricultural Film Plastic Scrap MATERIAL : PVC Agricultural Film CATEGORY : PVC TYPE : Film GRADE : Light Blue SPECIFICATION : From post-industrial, 100% PVC, no coating ORIGIN : Japan LOADING WEIGHT : 24 Tons FOB (USD/Ton) : 400-700

MATERIAL : PVC Flex Clear CATEGORY :PVC TYPE :Flex GRADE :Clear SPECIFICATION :"PVC clear flex made from shower curtain, 1 load, 18 tons Origin in USA ORIGIN : US LOADING WEIGHT : 18 Tons CNF (USD/Ton): $750-950MT Asia main port

Rigid PVC Sheet Reground White For Sales MATERIAL Rigid PVC Sheet Reground White CATEGORY PVC TYPE Regrind GRADE Clear SPECIFICATION Origin in Japan Origin Japan LOADING WEIGHT 24 Tons FOB (USD/Ton) 800-1000

PVC decor regrind Material : PVC decor regrind Category : PVC Type : Decor GRADE : Regrind SPECIFICATION : Canada origin,2loads per month Origin : Canada- Montreal Loading Weight : 18 Ton Fas (usd/ton) : 450$ Packaging : jumbo Bag Est. Shipping Time: 15, 30, 45 Days

PVC Pipe Regrind Grey Plastic Scrap For Sales MATERIAL : PVC Pipe Regrind Grey CATEGORY : PVC TYPE : Regrind GRADE : Grey SPECIFICATION : Origin from Japan ORIGIN : Japan LOADING WEIGHT : 25 Tons CFR (USD/Ton): Busan 550-700

PVC Pipe Fitting Regrind White Color Plastic Scrap Material For Sales MATERIAL : PVC pipe fitting regrind White color CATEGORY : PVC TYPE : pipe fitting regrind GRADE : White color SPECIFICATION : PVC pipe fitting regrind white color USA origin,no information of CaCO3. Post industrial. 5 loads available ORIGIN : US LOADING WEIGHT : 19-20 Tons FAS (USD/Ton): 680-880

PVC Pipe Regrind Grey Color Plastic Scrap Material For Sales MATERIAL : PVC pipe regrind grey color CATEGORY : PVC TYPE : pipe regrind GRADE : grey color SPECIFICATION : PVC grey pipe regrind USA origin,no information of CaCO3 . 5 loads available ORIGIN : US LOADING WEIGHT : 19-20 Tons FAS (USD/Ton) 800-1000

PVC Flexible Lumps From Cables Scrap MATERIAL : PVC flexible lumps from cables CATEGORY : PVC TYPE : flexible lumps GRADE : from cables SPECIFICATION : 120,000 lbs PVC flexible lumps from cables, ongoing supply .Mixed color, USA origin ORIGIN : USA LOADING WEIGHT : 18 Tons CFR (USD/Ton) : 700-850 India

Rigid PVC Sheet Reground Clear Plastic Scrap MATERIAL : Rigid PVC Sheet Reground Clear CATEGORY : PVC TYPE : Regrind GRADE : Clear SPECIFICATION : PVC Sheet Reground Clear, Packing : In Fle-Con Bag. Early/Mid Aug ORIGIN : Japan LOADING WEIGHT : 24 Tons FOB (USD/Ton) : 900-1100