The Variable Speed Drive FRENIC series is equipped with functions and performance to meet all types of requirements, and in addition it is easily maintained and environmentally friendly. The series lineup ranges from simple to advanced-function models, enabling model choices matching situations for use. Fuji Electric provide Variable Speed Drives perfect for automating and with energy saving devices like a fan pump or carrier and variable speeds.
FEATURES LOWER SP10116L-G01 Spare Parts is installed on 100RV-SP Vertical slurry pump. 100RV-SP Vertical Slurry Pump is designed for handling abrasive and corrosive liquids and slurries, while submerged in sumps or pits. Suited for applications requiring greater reliability and durability than conventional vertical process pumps can offer. It is mainly used for pumping the slurries with high abrasive, strong corrosion and high concentration liquids contain suspended solid particles. Design Features: Bearing Assembly - The bearings, shaft and housing are generously proportioned to avoid problems associated with the operation of cantilevered shafts in the first critical speed zones. The assembly is grease lubricated and sealed by labyrinths; the upper is grease purged and the lower protected by a special flinger. The upper or drive end bearing is a parallel roller type whilst the lower bearing is a double taper roller with preset end float. This high performance bearing arrangement and robust shaft eliminates the need for a lower submerged bearing. Column Assembly - Completely fabricated from mild steel. The SPR model is elastomer covered. Casing - Has a simple bolt-on attachment to the base of the column. It is manufactured from a wear resistant alloy for the SP and from moulded elastomer for the SPR. Impeller - Double suction impellers (top and bottom entry) induce low axial bearing loads and have heavy deep vanes for maximum wear resistance and for handling large solids. Wear resistant alloys, polyurethane and moulded elastomer impellers are interchangeable. The impeller is adjusted axially within the casting during assembly by external shims under the bearing housing feet. No further adjustment is necessary. Upper Strainer - Drop-in metal mesh, snap-on elastomer or polyurethane for SP and SPR pumps. Strainers fit in column openings. Lower Strainer - Bolted metal or polyurethane for SP, moulded snap-on elastomer for SPR. Discharge Pipe - Metal for SP, elastomer covered for SPR. All wetted metal parts are completely rust protected. Submerged Bearings - None Agitation - An external agitator spray connection arrangement can be fitted to the pump as an option. Alternatively, a mechanical agitator is fitted to an extended shaft protruding from the impeller eye. Materials - Pumps can be manufactured in abrasive and corrosive resistant materials.
Slurry Pumps are the most comprehensive range of centrifugal slurry pumps for use in mining, minerals processing, coal preparation, dredging, metallurgy, power plant, chemical and general industry applications. The wetted parts materials designed by High abrasion and corrosion resistance alloy, rubber or polyurethane etc, Expecially for handling high abrasive, high density slurries. Design Features Bearing assembly - a large diameter shaft with short overhang minimizes deflection and contributes to long bearing life. Only four through bolts are required to hold the cartridge type housing in the frame. Volute Liners - easily replaceable liners are bolted, not glued, to the casing for positive attachment and east of maintenance. Hard metal liners are completely interchangeable with pressure moulded elastomer. Elastomer seal rings back all liner joints. Pump casing - Casing halves of cast or ductile iron with external reinforcing ribs provide high operating pressure capabilities and an extra measure of safety. Impeller front and rear shrouds have pump out vanes that reduce recirculation and seal contamination. Hard metal and moulded elastomer impellers are completely interchangeable.
Metslurry is a professional company supplying slurry pumps and spares, and also focus on making a world-level supply chain to the mining world, we provide interchangeable pumps, the quality is the same as warman. The models are ah(r), sp(r), l(r), m(r), g series and so on. We have very professional team to select the correct slurry pumps and give after-sales services. Our goal is to be your spare parts warehouse and workshop. We already have built 3 warehouses and workshops in china, australia and laos, so most common parts are in stock in above area, it is fully guaranteed for delivery time if you have any enquiry or urgent need.
Feature of the product: use of double casing , it has the character of high efficiency , wear-resistant, Stable performance and ecxellent changeable parts , the material of liner and impeller is adopt of wear-resistant metal or rubber , the discharge port can be positioned ar 8 differernt positions at an intervals of 45°. The pumps may be installed in multistage series , may be driven by belt or direct Connection, the seal of shaft may be adoptable of gland seal , expeller seal or mechanical seal, the direction of rotation from the drive end is clickwise Application: the pumps are suitable for deliverling abrasive , high density slurries in the metallurgical , mining, coal and power industrial departments , for example raw ore , middings , concentrates , gangues etc.
ZJ slurry pump is a new generation anti-wear, energy saving slurry pump.The ZJ series pumps used international advanced solid-liquid two-phase flow theory and were designed using the minimum-wear principle.The flow parts of these pumps are suitable for the flow of state media for it's set shape, which reduces hydraulic loss of eddy and impact, both in pump and along the pipelines; so reduced friction of flow parts, lower noise and vibration of the pump translates into improved hydraulic efficiency. Product name: ZJ slurry pump Item:advanced slurry pump than AH slurry pump Features: ---Cetnrifugal cantiliver type, easily repair bearing house ---Can transport high density slurry containing highly hard abrasive particles like concrete, coal cinder, cement, clay, grit ,juice etc ---The slurry density can be up to 60% Data sheet : ---Capacity: up to 19*20m3/h ---Head:up to 94m ---Material: High chrome alloy and rubber lined Function Introduction: ---Mining, metallurgy, coals, electricity, construction material industry etc
Main parameter: Capacity(flow rate): 86.4-198 m3/h Head: 9-52 meter Rate speed: 1000-2200 r/min Impeller diameter: 245 mm 1. Application: Mh series of slurry pump is a kind of cantilever centrifugal slurry pump, widely applied for pumping high abrasive and erosive slurry in thermal power generation, chemical, mining, coal mining, metallurgy, environmental protection. 2. Sealing type of slurry pump: Shaft sealing use packing seal, associated-impeller seal and mechanical seal, can be applied for different work condition requirements. 3. Structure of slurry pump: Use double shell structure, the pump body, pump cover be lined with replaceable wear-resistant metal liner or rubber liner. The pump press out opening can be rotary mounting according to eight angle to meet different installation requirements. Meanings of the model: mh75c M---------wear-resistant high chromium alloy H---------heavy type slurry pump 75------- the pump press out opening is 75 mm C -------bracket style Wooden box
Gravel and sand pumps for sales : 1.Horizontal, cantilevered, centrifugal, single stage slurry pump 2.Long bearing life: the bearing assembly is with large diameter shaft and short overhang. 3. Wear resistant and anti-abrasion wet parts: a05, a07, a33, a49 and rubber etc. They are completely interchangeable with each other 4. Easily replaceable liners: liners are bolted to the casing. 5. Easy adjustment of impeller: an impeller adjustment mechanism is provided below the bearing housing. 6. Simple maintenance throat-bush: the mating face of the throat bush is tapered, so the wear is reduced and removal is simple. Main parameter:mg150e
Slurry pump is a kind of centrifugal pump to transport slurry materials under the centrifugal force. It transfer the electricity energy into kinetic and position energy. It is widely applied in mine, electricity, metallurgy, coal and environmental protection for abrasive solid containing slurry transportation. It can also be used to transport some corrosive slurry with crystals.
Product Description Introduction: Slurry pump can be widely used in mines, electric power, metallurgy, coal, environmental protection and other industries transport slurry containing abrasive solid particles.Such as metallurgical mill pulp conveying, hydraulic ash thermal power plants, coal washery coal slurry and heavy media delivery, dredging river, river dredging, etc.In the chemical industry, also can carry some corrosive slurry containing crystallization. Structure: Single stage, single suction, overhang shaft, centrifugal, double-casing horizontal pump, Wet ends are made of abrasive resistant hard metal or rubber. Base- High strengthened base is connected with Frame Plate by bolts; The Adjusting Bolt under the Bearing Assembly realize easy adjustment to impeller clearance. Bearing Assembly: -High rigidity shaft to handle heavy duty work condition; -Cartridge bearing assembly jointed with base by bolts; -Grease Lube bearings fitted in sealed bearing housing, the two labyrinth on both ends prevent the grease from contamination. Shaft Sleeve - Clearance fit between solid solution treated stainless steel shaft sleeve and shaft as well as the O-rings on both ends prevent the shaft from abrasion and erosion. Casing - Made of Gray Iron or Ductile Iron, Ribs help casing to stand high pressure. Impeller - Pump out vanes on both shrouds reduces recirculation and seal pressure. Wet Ends - Impellers, liners, volutes made of High-Chrome alloy or rubber, both materials are interchangeable. Slurry Pump Spares Pumps spare and parts material : High chrome alloy:A33, A05, A07, A49, etc. Industrial slurry pump, corrosion resisting slurry pumps Natural rubber: R08, R26, R33, R55, etc. Other material as per requests, like stainless steel, duplex stainless steel, Nickle alloy, Alloy 20, and so on. Applications Mining Coal washery Power plant Metallurgy Petrochemical Building material Dredging Other industrial departments, etc. This series of pumps are preferred by many customers with special installation requirements and widely applied in pool. Its wear-resistant metal liner could handle abrasive slurries with rough particles and high concentration.
Product Description The TS/TSR heavy duty cantilever sump pump is designed for applications requiring greater reliability and durability than conventional vertical process pump can offer. The heavy duty cantilever design makes the TS/TSR pump ideally suited for heavy continuous handling of abrasive and corrosive liquids and slurries whilst submerged in sumps or pits. Fully elastomer lined or hard metal fitted. No submerged bearings or packing. High capacity double suction design. Optional recessed impeller and suction agitator available. · TS pump - hard metal construction · TSR pump - rubber covered construction Structure: Fully Cantilevered – Eliminates submerged bearings, packing, lip seals, and mechanical seals that other vertical slurry pumps typically require. Impellers – Unique double suction impellers; fluid flow enters the top as well as the bottom. This design eliminates shaft seals and reduces thrust load on the bearings. Large Particle – Large particle impellers are also available and enable passing unusually large solids. Bearing Assembly – The maintenance friendly bearing assembly has heavy duty roller bearings, robust housings, and a massive shaft. Casing – The metal pumps have a heavy walled abrasive resistant 27% chrome alloy casing. Rubber pumps have a molded rubber casing adhered to sturdy metal structures. Column and Discharge Pipe – The metal pump columns and discharge pipes are steel, and the rubber columns and discharge pipes are rubber covered. Upper Strainers – Snap in elastomer strainers fit in column openings to prevent overly large particles and unwanted refuse from entering casing of the pump. Lower Strainers – Bolt-on cast strainers on the metal pump and molded snap-on elastomer strainers on the rubber pumps protect the pump from oversize particles. Specification 300T-TS Vertical Pump Capacity (Q) : 288-1267m³/h Head (H) : 6-33m Power (KW) : 200KW Speed(N) : 350-700r Effiency : 50 Impeller Dia.: 610mm Impeller No.: 5 Outlet Dia.: 300mm Weight: 3940kg Slurry Pump Spares Pumps spare and parts material : High chrome alloy:A33, A05, A07, A49, etc. vertical slurry pump Natural rubber: R08, R26, R33, R55, etc. Other material as per requests, like stainless steel, duplex stainless steel, Nickle alloy, Alloy 20, and so on. Applications Mining Coal washery Power plant Metallurgy Petrochemical Building material Dredging Other industrial departments, etc. This series of pumps are preferred by many customers with special installation requirements and widely applied in pool. Its wear-resistant metal liner could handle abrasive slurries with rough particles and high concentration.
Www.Hanhe-pump.Com Hanhe group co., limited Professional slurry pump dredging pump manufacturer and exporter china. Our slurry pump are dimensionally interchangeable with warman® slurry pump. Ah, hh, l, m slurry pump, g gravel pump and wn dredging pump. Warman ah, warman hh, warman l, warman m
Wzj model for the single-stage, single-suction, cantilevered horizontal centrifugal slurry pump, this series pump adopt international advanced solid-liquid two-phase flow theory, according to the principle of minimum loss design. The over-current components geometry conforms to the flow of the medium, to reduce the eddy current and impact, so as to reduce the flow components of wear, improved the hydraulic efficiency, reduce the running noise and vibration;
Slurry pumps Our xh model=ah model 1) about us: ¡¡1. We are over 10 years leading professional slurry pump manufacturer in china. ¡¡2. Top quality of raw material castings. ¡¡3. Advanced equipment with mature experiences engineers. ¡¡4. Large size factory with strictly quality control system. 2) slurry pump parameter: Wooden box
Series lmh slurry pump is mainly used for handling strong abrasive, high density slurries in the metallurgy, mining, coal washery, power plant, building materials and other industries etc. This series of slurry pumps have replaceable wear-resistant metal liners. Its wet parts are with throat bush, impeller, an be positioned at intervals of 45 degrees by request and oriented to any eight positions to suit installations and applications. Here are the drive types, such as v belt drive, gear reducer drive, fluid coupling drive, and frequency conversion drive devices. The pumps may be installed in multistage series to meet the delivery of long distance.
Series lrh slurry pumps are cantilevered, horizontal, centrifugal with double casings. They are designed for the handling of highly abrasive, high-density slurries. Structure: the wet parts of this pump are made of natural rubber, which could be replaceable wear-resistant parts. The discharge side can be oriented to any of the eight different positions. The shaft seals may adopt packing gland seal, expeller seal and mechanical seal. Application: series lrh slurry pump mainly applies in the metallurgy, mining, coal washery, power plant, building material and other industries. This pump can be installed in multistage series.
Introduction: Series lmhh slurry pumps are cantilevered, horizontal and centrifugal. The main feature of this series is to transport the slurry for high pressure. Because of its high speed, only metal lined pump could meet the design requirements and the rubber not. Structure: the wet parts of lmhh pump are made of wear-resistant alloy. The shaft seals for series lmhh may be packing seal and expeller seal. The discharge side can be oriented to any of the eight positions to suit installations and applications. Application: they are designed for the handling of highly abrasive, high density slurries in the metallurgical, mining, coal, power generation, construction material and other industry. The pumps could be also installed in multistage series for long delivery Packing: plywood case
Application and features: Type ms, hs and hhs pumps are cantilevered, horizontal, centrifugal slurry pumps. They are designed for handling abrasive, high density slurries in the metallurgical, mining, coal, power, building material and other industrial departments etc. The pumps of this type also may be installed in multistage series. The frame plates for type ms, hs pumps are made of interchangeable, hard metal or pressure moulded elastomer liners. The impellers are made of hard metal or pressure moulded elastomer liners. The frame plate liner and impeller for hhs pump are made of hard metal only. The shaft seal for type ms, hs and hhs pumps is gland seal or centrifugal shaft seal. The discharge branch can be positioned at intervals of 45¡ã by request and oriented to any eight positions to suit installations and applications.
Type vs and vsr pumps are vertical, centrifugal slurry pumps submerged in sump to work. They are designed for delivering abrasive, large particle and high density slurries. These pumps have no need of any shaft seal and sealing water. They can also be operated normally for insufficient suction duties. Wet parts of type vs pump are made of abrasion-resistant metal. All parts of type vsr pump immersed in liquid are lined with rubber outer liner. They are suited to transport non-edge angle abrasive slurry. The type with¡°l¡±is a sump pump of extension shaft series, which is suited for the working condition of deeper level. The guide bearing construction is added to the pump on the basis of the standard pump, so the pump is with both more steady operation and wider application range, but flushing water should be attached to the guide bearing.
Product name THM-3C slurry pump Type THM pump size 4/3 Capacity 86.4-198m3/h Head 9-52m Allowable Max. Power 30kw Speed 1000-2200r/min NPSH 4-6m Introduction Model Explanation and Performance Chart: THM-3C T: Tower pump H: High Concentration M: Metal lined 3: Discharge size (inch) C: Frame type with maximum power Introduction of Slurry Pump ---- THM Series THM Series slurry pump is mainly used for handing strong abrasive, high density slurries and low density, high head slurries in the metallurgical, mining, coal, power, building material and other industrial departments etc. The features of this kind of slurry pump The frame plates of this kind of slurry pump have replaceable wear-resistant metal liners. The impellers are made of wear-resistant metal. The frame plate liner and impeller for THM pump are adoptable of hard metal only. Bearing assembly of this kind of slurry pump use cylindrical structure, adjusting the space between impeller and front liner easily, being removed completely when being repaired. Bearing assembly use grease lubrication. The shaft seal of this kind of slurry pump could use the packing seal, expeller seal and mechanical seal. The discharge branch can be positioned at intervals of 45 degrees by request and oriented to any eight positions to suit installations and applications. Here are the drive types, such as V belt drive, gear reducer drive, fluid coupling drive, and frequency conversion drive devices. Wide performance, good NPSH and high efficiency are main character of these kinds of slurry pump. The pump of this type may be installed in multistage series to meet the delivery for long distance. Main application of this kind of slurry pump This kind of slurry pump mainly applies in coal washer processing, handling with the fine ore and tailings in metal mine, handing combined bottom and fly ash in a thermal power station etc. Pump Model THM Series Impeller Dia. Allowable Max.Power Clear Water Performance Capacity Q Head H(m) Speed n(r/min) Max.Eff. ¦Ç% NPSH (m) m3/h l/s THM-1B 15 12.6-28.8 3.5-8 6-68 1200-3800 40 2-4 152 THM-1.5B 15 32.4-72 9-20 6-58 1200-3200 45 3.5-8 184 THM-2C 30 39.6-86.4 11-24 12-64 1300-2700 55 4-6 214 THM-3C 30 86.4-198 24-55 9-52 1000-2200 71 4-6 245 THM-3D 60 THM-4D 60 162-360 45-100 12-56 800-1550 65 5-8 365 THM-4E 120 THM-6E 120 360-828 100-230 10-61 500-1140 72 2-9 510 THM-6R 300 THM-8ST 560 612-1368 170-380 11-61 400-850 71 4-10 686 THM-10ST 560 936-1980 260-550 7-68 300-800 82 6 762 THM-12ST 560 1260-2772 350-770 13-63 300-600 77 3-10 965 THM-14ST 1200 1368-3060 380-850 11-63 250-550 79 4-10 1067 exported wooden crate
