* PHOSCAST Phoscast : Phosphate Bonded Castables * PURPOSE customers using FBC boilers (Particularly underbed feed FBC boilers) for the protection of inbed coils against erosion potential by applying highly abrasive resistant refractory on inbed coils above fuel feed system. BACKGROUND * Two of such actions are providing special alloy studs on inbed coils and applying highly abrasive resistant refractory on the outer bottom loops of inbed Coils which are above the fuel feed nozzles. * GANESHAS has taken number of approaches to identify the key factors affecting erosion rates with an objective to enhance the life of inbed tubes as well as implementing the corrective action to reduce the erosion rates. Phosphate coatings are often used to protect steel parts against rusting and other types of corrosion * Erosion of inbed coils in fluid bed combustor is unavoidable phenomenon however the rate of metal wastage and thus the life of tubes depends on various factors like ash & fuel properties, design of Combustor / feeding system, flue gas velocities operating conditions etc. It has been also observed that maximum erosion prone inbed coils are those which come above fuel feed nozzles and an area of approximately 1 to 1.5 mts around fuel feed systems are badly affected. APPLICATION Phoscast-90 XR can be applied by ramming with wooden mallet having adequately large head @" dia x 5" length x 10â?? Jong handle). The desired lining or repair thickness is built up in several courses while ramming the mass to uniform thickness. Phoscast refractory should never be trawled to obtain smooth surface; ramming only should finish surface. Any excess mass is to be sliced off with trowel edge and then finished by ramming again for bed coil. Tube application of AFBC boiler, the material pasty mass should be finger pressed into the studs of the tube with maximum force. Finish should be given by pressing the hand palm against material applied, using surgical type thin rubber hand gloves.
Ramming mass is commonly used in metallurgy, building materials, non-ferrous metal smelting, chemical, machinery and other manufacturing industries. Ramming mass is widely used in non-core intermediate frequency furnace and core induction furnace. As an intermediate frequency furnace ramming material, refractory ramming is applied to melt gray cast iron, nodular cast iron, malleable cast iron, vermicular cast iron, and cast alloy steel; to melt carbon steel, alloy steel, high manganese steel, tool steel, heat resistant steel, stainless steel, molten aluminum and its alloys; to melt red copper, brass, white brass, bronze and its alloys, etc. Induction furnaces are used for melting cast iron, mild steel and various alloy steels in foundries and making of steel in mini steel plants using sponge iron The refined high silicon, low iron quartz sand and quartz powder are selected and the fused quartz sand is added as the refractory material., with no slag, no crack, damp proof, convenience of repair, and the corrosion resistance, thus greatly improving the furnace service life span and the economic benefit.. Silica ramming mass can safely be used up to an operating temperature of 1600 deg C. Since it expands very little, it is superior to both alumina and magnesia refractories to resist thermal shocks Acid ramming material is the premixed ramming mass of the lining material. The acid ramming mass is used to smelt a series of metal materials such as ordinary steel and carbon steel. The lining practice best suited to a particular furnace depends upon the capacity and design of the furnace, operation practice adopted during making of a heat, and furnace output.
METHOD OF APPICATION: * Mastic compound application consist of two coats of. Primer ,Primer and followed by Mastic compound in recommended thickness, ranging from min. 12mm to 25mm in one or two layers to achieve desired thickness without any pin hole and crack. 1). Surface preparation and application of Primer: Refer application method of Primer. 2). After doing necessary surface preparation and application of primer coating, area to be installed with Mastic compound should be divided in to equal no. bays. To maintain even thickness required, place wooden or aluminum batten. Mastic compound is then broken in small pieces and put it in heating pan. While heating, keep material moving to avoid burning. It is heated until it comes in a uniform consistency and then applied on the surface and works it with wooden float, to achieve uniform thickness and smooth surface free from any pinholes. CHEMICAL RESISTANCE PROPERTIES: * Mastic compound has good resistance to weak, diluted acids, alkalis salts etc. It is not recommended to use against strong acids, oxidizing acid solvents, oil and fats STORAGE & PACKING: * Keep Mastic compound away from direct sunlight, heat solvents etc. Under this condition, its shelf life is unlimited. It is supplied in cake form and approx. wt. is 10 kgs. HEALTH & SAFETY: * Handle melted Mastic compound compound very carefully . Avoid contact with skin. It is advisable to wear protective wears at the time of use of Mastic compound and all other our products. This information, given in good faith, is based on results gained from experience and tests. However, all recommendations or suggestions are made without guarantee since the conditions of use are beyond our control.
APPLICATION OF SK-HB K-SILICATE MORTAR : * K-SILICATE is used for jointing Acid Resisting brick in construction of vessels in suited for construction of fume chambers and stacks handling hot, dry Acid fumes and vapors. It is also used for jointing chemical resisting stoneware pipes. K-SILICATE cement is good bedding material for Acid â?? Resisting bricks and tiles. The concrete surface needed protection should be dryed, clean and rough. The bricks or tiles will be set with K-SILICATE cement over concrete surface applied with a suitable an impermeable interliner. When Bedding and Jointing Materials are the same. On the treated surface bricks or tiles are bedded to a thickness of about 6 mm and tamp gently with a wooden piece till the paste squeezes out of joints. The paste that is squeezed out of the joint should be removed by trowel with good finishing. After the mortar of the joint is dryed treat the joints with 20% Hydrochloric Acid Solution by means of brush. A.R.lining should be always in contact with Acid and not with water. Concrete subtract like Floor, Wall, tanks and similar surface should be protected with a membrane of Bitrok Mastic or compound steel tanks should be protected with rubber or PVC subjected to chemical conditions and temperature of chemical media. The Brick lining is recommended over the protective layer of Bitrok Mastic. When Bedding and Jointing Materials are Different. Spread the silicate type mortar about 6 to 8 mm thick on the back of the tile or brick. Press the tile on the bed leaving required space for joints between tiles for bricks. After the bedding mortar is set, fill Mp the joints with specified cement.PRODUCT DATA SHEET FOR SK-HB ( K-SILICATE) MORTAR A general purpose cement for acid conditions Resistant to High & medium concentrations of most of the common organic and inorganic acids except Hydroflouric acid. Recommended where the concentration of the acid is high suitable for high temperature. Unsuited to aqueous solutions, alkaline conditions. PREPARATIONS OF MORTAR : * Measure 1 part by weight of K-SILICATE solution into a suitable mixing pan. * Add slowly and gradually 3 parts by weight K-SILICATE mortar and mix thoroughly to form a smooth mortar. * In hot season very large batches of mortar will become stiff quite rapidly therefore small batches, not exceeding 4 to 8 kgs. Will be prepared. * The cement mortar will be used before it starts setting.
This is chemical setting Furan based chemical resistant mortar which is combination of Liquid and Powder, when mixed in proper proportion from workable mortar which after setting and curing give of liquid and give black highly cross linked composites. Furan When set and cured is resistant to highly corrosive acids, alkalis and to powerful organic solvents such as ketones, Aromatic and Chlorinated solvents. It has extreme resistant to Acidic & alkalis, Salts, Greases and Detergents. It resists to Organic & Inorganic acids at their boiling temperature. It is suitable against mild chlorine Gas (dry) phosphorous trichloride, pyridine at room temperature. Furan is especially useful where resistance to mixed media such as aqueous acids /alkalis and organic solvents is needed in chemical plant process and waste streams. Carbon filled Furan is used against corrosive effect of hydrofluoric acid & its salts. PREPARATION OF FURANE MORTAR : Mortar consist of Furan solution and Furan powder. The average mixing ratio necessary to obtain mortar with good working consistency is 1 part by weight Solution & 3 part by weight powder. The ratio will vary slightly depending on temperature and working conditions.Stir the liquid thoroughly before using. Place liquid in a suitable shallow mixing pan. Add powder by weight in the solution mix thoroughly and rapidly until all lumps are dispersed and the mortar is completely homogenous. Spread out the mortar in a thin layer, not more than ¾ thick, to dissipate the heat of reaction and lengthen the working life. Batch size can be varied depending upon the temperature and the speed with which the masons are working. Very large batches will become stiff quite rapidly. Make sure that all the Furan Motrar is used from the pan before another batch is mixed.When working at temperature above 40 C, very small batches not more than 2 Kgs, should be prepared. When working at temperature below 15C the liquid should be kept warm.
DATA SHEET FOR EPOXY EPOXY COATING :- INTRODUCTION - EPOXY COATING (HYB) is a two part high solids solvent free epoxy phenolic resin based coating system designed for hard wearing, smooth surface finish for floors, walls and on steel structures. Nonskid surface finish can be achieved on floor, if required. FEATURES: 1) Hard Wearing 2) Non Dusting 3) Excellent Surface Finish 4) Non Smelling 5) Good Aesthetics 6) Highly Chemical Resistant APPLICATION: 1.Stir well before mixing Part A and Part B and mix in the prescribed ratio. 2.Apply one coat of EPOXY primer on the clean and dry surface. 3.EPOXY COATING (HYB) should be applied on the surface by brush or roller within 24 hrs. After application of primer coat it should be allowed to air dry for min. 4 hrs. Preferable in a dust free atmosphere. 4.Apply min. 2 coats with the intercoat interval of 6-8 hrs. PRODUCT SPECIFICATIONS: Application - Brush, Roller Mixing Ratio - As Directed on Packing Port Life - 30 Mins. Drying Time - Touch Dry- 30 Min, Hard Dry 6 Hrs. - Intercoat Interval 6-8 Hrs. Min. - Dry Film Thickness 125-150 Microns/per coat - depending on porosity Covering Capacity - 6-8 sq.met/kg per coat depending on porosity, roughness & method of application. Color Shades - All Standard Shades RECOMMENDED USES: 1) Food & Pharmaceutical 2) Work Shop 3) Clean Room Application 4) Chemical Resistant Coating for Concrete& Steel 5) Petrochemical, Fertilizer plants METHOD OF APPLICATION: SURFACE PREPARATION The long-term durability of the applied Epoxy coating (HYB) epoxy coating is dependent on the adhesion between sub-base and coating material. It is most important therefore, that the substrate surfaces are correctly prepared prior to application. 1.Before application of the Epoxy coating (HYB) surface should be free from loose partials, rust, oils, grease or earlier coatings and should be totally dry. 2.New concrete or cementations surface should be placed at least 28 days and have a moisture content of less than 5% before application of Epoxy coating (HYB) 3.After surface is dry, all repair work like sealing of joints, cracks filling of cavities and crevices should be carried out. HEALTH & SAFETY - Keep the containers tightly closed when not in use. Avoid contact with skin & eyes. It comes in contact with the body, wash affected parts with plenty of water and contact a doctor. Other known sector for Epoxy floor lining, Epoxy garage floor lining, Concrete epoxy lining, Concrete floor epoxy lining, Epoxy pipe lining, Marine epoxy lining, Sub marine epoxy lining, Basement lining epoxy floor shield, Louisiana, Oregon, Chip lining color epoxy floor, Aviation lining epoxy interior.
Bitumen Primer * Bitumen Primer is Bituminous air curing ready mixed Acid & Alkali resistant special primer. Application * Concrete surface must be clean, dry and rough. No primer should be applied over smooth and wet surface. * After cleaning the concrete surface, one coat of Bitumen Primer should be applied with brush and allow to dry thoroughly. * The drying time will depend upon the temperature. * 24 Month at the temperature 30C (+2OC) Packing * Bitumen Primer: 25 Liter Drum Note * Bitumen Primer contains volatile and slightly toxic solvent. Keep away from spark and open flames at working area. * Bitumen premier it is manufactured using bitumen solution which is used for sealing of prime porous and non-porous surface, and also to protect residential and commercial building. * Bitumen Primer is used to protect substrate against corrosive attack, is suggested to apply anti-corrosive primer.It is best for protection against sub-striate against atmospheric corrosion and chemical corrosion. It is a mixed substance made up of organic liquids that are highly sticky, water proof, viscous,acid proof as with all surface coating, good Bitumen Premier is used for long life of the system. it is applied by brush or roller and allowed to dry before any water proofing treatment so to avoid solvent it is used in defects such as cracks, broken mortar joints, etc. are to be repaired prior to Bitumen primer application. Product Details: Grade Standard Technical Grade Physical State - Liquid Usage - Industrial Color - Black Characteristics: Appearance/Color - Pasty liquid/ black Chemical Base - Bituminous rubber emulsion. Density - 1.0 kg/l Curing Speed/ Rate - 3 - 4 hours Tack free after - 5 - 10 hours Cured after - 2 - 4 days (Dependent on ambient Solid Content by - temperature, substrate temperature, Weight - relative Water Content by weight - humidity and thickness of the coating) Bitumen Content - 41% by weight - Thixotropic (The viscosity can be adjusted by - Viscosity adding up to max. 5% of clean water. - Stir well prior use) - For light protection: 1.0 mm min. Coating - For greater protection: ~ 1.5 - 2.0 mm Thickness applied - in two coats. Water Penetration - 48 h, 1 bar: 78.5 cm2: 0 ml under Hydrostatic - 96 h, 4 bar: 78.5 cm2: 33 ml Pressure - Water vapor 6 x 10-7 mg / hmPa Permeability Service - -30 C to 200 C Temperature - Adhesion Concrete - Very good, Timber: Very good, Metal: Moderate Glass: Poor
Acid / Alkali Resistant Tiles/Bricks * Our Acid proof tiles, Acid alkali resistant tiles, Chemical resistant tiles are fully vitrified tiles which are manufactured using special non ferrous clay, processed at extremely high temperatures this process causes the raw materials to fuse and form a compact mass with an extremely low water absorption of less than 0.5% resulting in the formation of a very strong body with a flexural strength of 38 N/mm2, solid through color fade proof with a very hard surface Mohs hardness of 7. * The acid resistant tiles come in a range of sizes and thicknesses from ranging from 8-25mm. Our acid proof tiles meet stringent specification norms of IS 4457:2007 and relevant ASTM/DIN standards which ensure excellent performance in Acid/Alkali/Chemical (expect Hydrofluoric acid and its derivatives). Corrosion Protection Applications * Factory Floors subject to corrosion from Chemicals, Acids, Oil & Solvents * Pickling tank and surrounding areas * Food & Beverage Industry flooring * Battery rooms and Control rooms * Demineralization plants * Walls of washing and Paint shop areas * Acid Resistant Tiles Manufacturers India * Our acid proof tiles provide excellent abrasion resistance, anti-skid properties for worker safety and high aesthetic appeal. We also provide specialized corner tiles for reducing chances for acid attack through construction joints. Our standard sizes are 200x100, 200x200 & 300x300 millimeters.
Hulled sesame seeds are India's owns harvesting product since years. Shubhlaxmi Industry brings to you the premium quality Hulled sesame seeds with Auto Dried process. Hulled Sesame Seeds are Source of most nutritious seeds because of its proteins and valuable minerals. The husk hull (upper skin) of these seeds are removed hence are called as Hulled Sesame Seeds. The botanical name of Natural Sesame Seeds is Sesamum indicum and it belongs to family Pedaliaceae. Finest quality of natural sesame seeds are dried and hulled mechanically. Natural sesame seeds can be sundried too to get hulled sesame seeds. Sesame seeds are oxidative and hence can reverse the liver damage. In Arabian countries, Tahini is mixed with Date syrup to make sweet drink. Hulled Sesame Seeds are widely used in breads, burgers, sauces, cereals, crackers, spreads, drinks, granola, candies,food dish garnishing & various other bakery and confectionary products to enrich its taste and nutritional values. Specification HS Code 012074090 Purity Levels : 99.90%/99.95%/99.97%/99.99% Moisture : 4% Max Oil Content : 48% Min Admixture : 1%/0.03%/0.02% E-coil : Nil Color : Milky White Aflatoxin (b1+b2+g1+ Bellow 4ppb Salmonella absent/25gms Packing : 5/10/25/50 Kg Net Pp. & Brand Packing Quality Assurance ; Sgs,geo-chem Loading Capacity : 19mt In 20'fcl
Hanger & shoulder Fire bricks are special type of brick which are form of Refractory ceramic material. It is used for Roof lining of Boiler, furnace, kiln, fireplaces & fireboxes. Hanger & Shoulder Brick are used for Reheating furnace roof. There are three qualities of Hanger & shoulder brick as per their specification 40% Alumina Hanger & Shoulder Brick 50% Alumina Brick Hanger & Shoulder Brick 70% Alumina brick Hanger & Shoulder Brick
Cupola Fire Bricks are special type of brick which are form of Refractory ceramic material. It is used for inner surface lining of Boiler, furnace, kiln, fireplaces & fireboxes. Quality: We offer various quality bricks are IS-6, IS-8, PI - 30% to 70% Alumina offering high temperature resistance of 1100 C to 1700 C Sizes of Cupola Bricks: Length 9 Inch & 11 Inch Dia (Inch) 9D, 12D, 15D, 18D, 21D, 24D, 27D up to 56D
Acid Resistance bricks & Tile are special form of masonry bricks which are chemically resistant and thermally durable. These are used for masonry construction and flooring which is prone to chemical attack. These products are classified as per the different standard. Class - I Class - II Sizes of Bricks: 230 x 115 x 75 mm, 230 x 115 x 65 mm, 230 x 115 x 38 mm, 230 x 115 x 25 mm Sizes of Tile: 230 x 115 x 20 mm / 15 mm / 12 mm 200 x 100 x 20 mm / 15 mm/ 12 mm 300 x 300 x 15 mm / 12mm
Insulation Bricks are used for hot face & back up insulation lining of Boiler, Reheating furnace, Blast furnace, reactor chamber, high temperature furnace etc. Insulation Bricks are providing energy efficiency by minimising heat loss. They have feature of low density, high purity, low thermal conductivity, excellent thermal shock resistance. Types of Insulation Bricks: Cold Face Insulation Bricks Hot Face Insulation Bricks HFK Insulation Bricks Porosint Insulation Bricks Sizes: Standard 9 * 4.5 * 3 Inch
We offer superior quality sponge iron that is also known as direct- reduced iron. Our offered sponge iron is made for high grade, 65-70 fe Min fem-80%, fet-90-92%, s-0.04% max. Loose in form of lumps. Sponge iron filter material In industry through a sponge iron production equipment is widely applied iron phosphorus reduction method, method of reduction of iron ore concentrate, etc., the rolling iron phosphorus or ore concentrate after reduced iron press down into pieces, into the roasting tube into the kiln roasting, produce the high quality reduced iron. Sponge iron filter material for the first time into the deaerator, must first after backwashing, remove the sponge iron residue on the surface of the filter material float ash impurities.
Natural Phyton-Herbal Skin Mist 1. Plant-based mixture ingredients remove pore choking and toxicity resulting from dead skin, active factors of the extract are supplied as nutrition factors to the skin, skin's self-healing and recycling process stimulation make your skin bright, soft, and elastic. 2. Antioxidant properties of active factors inhibiting skin free radicals, enhance skin cells, offering an antibacterial active function against external infectious factors.
Foodix- Offering Instant Mix for Murukku. One of the Most wanted Indian Snacks and widely prepared when the festively time Like Diwali. Preparation 1. Empty the contents of this pack and mix it with 2 cups (Approx. 300ml) of water. Then add 25g of butter or two tablespoons of oil (30 ml) and make it into a dough. 2. Heat oil in a pan 3. Insert the dough into the mould and press the mould to make spirals either on a cloth, butter paper, foil or flat hold ladle. 4. Place the ladle in the oil or remove the Murukku and drop gently in the hot oil. Fry until golden brown and crisp. 5. Drain the fried MURUKKU on the kitchen tissue to remove excess oil. Cool them completely. Store them in an airtight container for delicious Murukku. Can be used for preparing Spicy/Sweet Murukku. Add chilli powder/ sugar as per your preference Serving size This pack gives 50 pieces of Murukku (6 cm diameter)
Copra We make high-quality copra by drying fresh coconut meat (kernel) in hybrid solar dryers. With efficient and continuous drying technology, we can reduce the moisture content of fresh coconut kernels from around 50% to lower than 6% within 48 hours. This result can be achieved by utilizing solar energy during daylight and renewable energy from smokeless biomass burning all night long. Moisture content: maximum 6%, Free Fatty Acid content: maximum 0.5%, Green: 0%, Burnt: maximum 2%, Smoky: maximum 5%, Rubbery: maximum 5% We only pick mature coconut fruits for the drying process, coconut must be put in a dryer immediately after opening to prevent microbes such as fungus, mold, and bacteria to grow. We keep the temperature in the oven dryer between 60 to 70 degrees Celsius. We inspect the copra periodically during the drying process, any damaged copra should be removed from the oven dryer immediately.
Ginger is one of the earliest known oriental spices and is being cultivated in Indonesia for both as fresh vegetable and as a dried spice, since time immemorial. Ginger is obtained from the rhizomes of Zingiber officinale The ginger family is a tropical group, especially abundant in Indo-Malaysian region, consisting of more than 1200 plant species in 53 genera. The area under cultivation in Indonesia is 107.54 thousand ha and the total production of the country is 385.33 thousand tons. PT Nif Internasional is one of the leading exporter of Fresh ginger from Karnataka which is located in the indonesia. We are located in the central hub of major Ginger production areas in Karnataka. Indonesia Fresh Ginger is well-known for its aromatic, spicy & pungent flavor. It is popularly used as a spice in Indonesia culinary preparations. Once the harvesting is done rhizomes are immediately subjected to high pressure water wash to remove the soil particles & other microbial debris adhering to the rhizomes & then shade dried for the certain extent to drain the water to prevent it from mold & other microbial growth. Our variety of Ginger is freshly harvested & packed in a temper proof packaging material to prevent it from degradation. Quality of the rhizomes checked by our quality inspection team before packaging and continuous monitoring the process of sorting & packaging & using standard packaging materials makes PT Nif Internasional to serve our clients with best product in a most professional way with competitive price. Health Benefits of Ginger : 1. It facilitates digestion. 2. It clears a sore throat and nose congestion. 3. Ginger is known for its healing properties. Specifications : Product - Fresh Ginger Variety - Rio - de - Janeiro Type - Water washed Each Rhizome Weight - 50/100/150/200 gms Packaging Type - Mesh Bag/ PP Box/ Cartoon Box Nett. Wt. per Package - 5/10/25/30 KGS Port of Loading - Port of Tanjung Priok - jakarta - Belawan - medan
Kaolin, soft white clay that is an essential porcelain and is widely used in the making of paper, rubber, paint, and many other products.
Olive Cherry Date seeds Removing Machine Fruit seeds stone Removing machine series fruit different capacity different ,machine are little different ) Apricot kernel remover stone /core removing machine Peach core remover Apricot,Peach,Jujube nut removing machine Red date/Peach and apricot /Green plum / Cherry /Hawthorn /Sandberry /Iraq date /Date de /Marinated peach kernel machine Olive /Li Zi /Nut and butter/Litchi/ Pear stone removing machine Longan /Automatic stone core removal machine of large-scale red date automatic jujube type /Hawthorn / Beach date /Prunus cherry and so on ...about 20-40kind fruit can be stone removing machine Technology advantage : 1. The full-automatic equipment has high degree of automation. The mold conveyor belt can automatically feed and send materials to carry out transportation and core flushing. It only needs to pour the fruit into the feed hopper to complete the separation effect of core and flesh. It can work continuously and solve the problems of low efficiency, labor-consuming and time-consuming of manual core removal. 2. The structure of the machine is composed of stainless steel thick wall square tube and channel steel welding, which makes the equipment more stable during start-up and operation. All parts are assembled with bolts, which makes the operation and maintenance of the equipment more convenient. 3. The raw material of the equipment is made of stainless steel, which meets the hygienic standard of food processing equipment. The conveyor belt is made of imported polyurethane material, which is wear-resistant, tensile, tear resistant and has a longer service life. 4. The operation of the machine is simple and convenient, without long-term care. One person can manage multiple machines at the same time. The transmission system adopts advanced design concept and standardized components. The principle of core punching adopts the process of machine tool to punch the core, so that each equipment meets the high design standard, so that the effect of core removing is good, and the fruit shape is completely unchanged.
