V3 Borewell Submersible Pumpset Falcon standard 73mm (3") Borewell Submersible pump is firmly coupled to a submersible electric motor which Operates by being submerged beneath the surface of the water. The optimal design of impeller and diffuser enables the best Possible hydraulic efficiency. Built-in check valve prevents back flow and reduces the risk of water hammering. All Vital components of these pumps are made up of corrosion resistance thermoplastic and the shaft is of SS 410. Pump Liquids - Clean - Thin - Non-Aggressive - Non-Explosive - Clear - Cold - Fresh water - Without abrasives - Solid particles. Salient Features - Motor portion covered with corrosive resistance Stainless steel (SS 204cu) shell - More durability and hygiene - High operating efficiency - Specially designed thrust bearing to withstand high axial thrust load - Extremely hardwearing water lubricated bearing - Thread type motor construction ensures service feasibility - Specially designed Deep Drawn type pump ensures perfect alignment and Thereby increases the life of the pump set - Designed for wide voltage operation - Best alternative for JET & Compressor pump set - Additional intermediate bearing in higher stage pumps. Specification - Power Range : 0.37 kW to 1.1 kW (0.50 HP to 1.5HP) - Version : Single Phase 160V to 230V, 50Hz, AC Supply - Speed : 2880 RPM - Head Range : 14 Mtr. to 96 Mtr. - Discharge Range : 70 LPM to 15 LPM - Outlet Size in Inch : 1.25" - Degree of Protection : IP 58 - Direction of Rotation : Counter clockwise from driving end -1 pH Minimum cooling 1pH - Flow Along the Motor : 0.15 m/sec. - Type of Duty : S1 (Continuous) - Method of Starting : 1ph-Capacitor - Maximum Starts Per Hour : 20 Times Characteristics Of Clear Cold Water - Maximum liquid temperature : 33C max - Permissible amount of sand : 25 g/m - Allowable solids : 3000 ppm (max.) - Chloride ion density : 500 ppm (max.) - Turbidity : 50 ppm silica scale (max.) - Hardness (Drinking Water) : 300 ppm (max.) - Specific gravity : 1.004 (max.) 6 - Viscosity : 6 1.75 x 10 m�²/sec (max.) - Ph Value : 6.5 to 8.5
V3 Borewell Submersible Pumpset Falcon standard 73mm (3") Borewell Submersible pump is firmly coupled to a submersible electric motor which Operates by being submerged beneath the surface of the water. The optimal design of impeller and diffuser enables the best Possible hydraulic efficiency. Built-in check valve prevents back flow and reduces the risk of water hammering. All Vital components of these pumps are made up of corrosion resistance thermoplastic and the shaft is of SS 410. Pump Liquids - Clean - Thin - Non-Aggressive - Non-Explosive - Clear - Cold - Fresh water - Without abrasives - Solid particles. Salient Features - Motor portion covered with corrosive resistance Stainless steel (SS 204cu) shell - More durability and hygiene - High operating efficiency - Specially designed thrust bearing to withstand high axial thrust load - Extremely hardwearing water lubricated bearing - Thread type motor construction ensures service feasibility - Specially designed Deep Drawn type pump ensures perfect alignment and Thereby increases the life of the pump set - Designed for wide voltage operation - Best alternative for JET & Compressor pump set - Additional intermediate bearing in higher stage pumps. Specification - Power Range : 0.37 kW to 1.1 kW (0.50 HP to 1.5HP) - Version : Single Phase 160V to 230V, 50Hz, AC Supply - Speed : 2880 RPM - Head Range : 14 Mtr. to 96 Mtr. - Discharge Range : 70 LPM to 15 LPM - Outlet Size in Inch : 1.25" - Degree of Protection : IP 58 - Direction of Rotation : Counter clockwise from driving end -1 pH Minimum cooling 1pH - Flow Along the Motor : 0.15 m/sec. - Type of Duty : S1 (Continuous) - Method of Starting : 1ph-Capacitor - Maximum Starts Per Hour : 20 Times Characteristics Of Clear Cold Water - Maximum liquid temperature : 33C max - Permissible amount of sand : 25 g/m - Allowable solids : 3000 ppm (max.) - Chloride ion density : 500 ppm (max.) - Turbidity : 50 ppm silica scale (max.) - Hardness (Drinking Water) : 300 ppm (max.) - Specific gravity : 1.004 (max.) 6 - Viscosity : 6 1.75 x 10 m/sec (max.) - Ph Value : 6.5 to 8.5
ESS 215KW Lithium Battery Energy Storage System 384VDC Rechargeable Lifepo4 Battery pack 280AH Energy Storage Battery 1. High energy density, small footprint, short construction period, strong environmental adaptability 2. Standardized components, modular architecture, easy for expansion 3. Battery module within the layered stack design, with more than 10 years of long design life 4. Efficient battery module and system cooling design 5. The use of international advanced IGBT and intelligent power module, with high power fast adjustment capability 6. BMS battery management system with SOC automatic calibration and high current active balance function, combined with the perfect operation control and management strategies to achieve accurate and efficient management 7. The combination of software and hardware protection, with alarm protection and automatic diagnostic functions, improve the protection strategy to ensure safe and efficient operation of the system 8. Our BMS use NXP(USA) automotive-grade high performance chip, strong anti-interference, good reliability, wide temperature range. 9. We use brand new high quality A-grade battery power cell, longer service life. 10. Charging and discharging are controlled separately, more convenient and reliable to control charging and discharging. 11. Big color LCD touch screen display, easy setting and operation. 12. Can built in solar charge controller and AC-DC charger, our BMS can intelligently manage charger to charge battery well, BMS can communicate well with battery, solar controller, ac charger and inverter, one integrated intelligent monitoring system. 13. Approved by UL1741 certificate. 14. Accept customized product, our lithium battery system are widely used in many situations, such as: Different residential home, hotel, shop, factory, hospital, commercial buildings, electric car, RVs, Van, mobile dining car, heavy truck, different ship/boats, ice-cream car, outdoor camper,.etc. Applications: 1.Energy Storage --Solar-Wind Power System / City Grid (On/Off) / Community and Family 2.Back-up System and UPS --Telcom Base / CATV system / Computer Server Center / Medical Instrumnt / Military Equipment 3.Other Applications --Security and Electronics / Mobile POS, Mining Lihgt / Torch / LED Light / Emergency Light --RV Motorhome /Golf Carts Battery / Boat Marine Yachts / Electric Skateboard / Electric bike / Electric Scooter / Electric bicycle --LED Backup / Engine Starting Battery,etc.
ESS 215KW Lithium Battery Energy Storage System 384VDC Rechargeable Lifepo4 Battery pack 280AH Energy Storage Battery 1. High energy density, small footprint, short construction period, strong environmental adaptability 2. Standardized components, modular architecture, easy for expansion 3. Battery module within the layered stack design, with more than 10 years of long design life 4. Efficient battery module and system cooling design 5. The use of international advanced IGBT and intelligent power module, with high power fast adjustment capability 6. BMS battery management system with SOC automatic calibration and high current active balance function, combined with the perfect operation control and management strategies to achieve accurate and efficient management 7. The combination of software and hardware protection, with alarm protection and automatic diagnostic functions, improve the protection strategy to ensure safe and efficient operation of the system 8. Our BMS use NXP(USA) automotive-grade high performance chip, strong anti-interference, good reliability, wide temperature range. 9. We use brand new high quality A-grade battery power cell, longer service life. 10. Charging and discharging are controlled separately, more convenient and reliable to control charging and discharging. 11. Big color LCD touch screen display, easy setting and operation. 12. Can built in solar charge controller and AC-DC charger, our BMS can intelligently manage charger to charge battery well, BMS can communicate well with battery, solar controller, ac charger and inverter, one integrated intelligent monitoring system. 13. Approved by UL1741 certificate. 14. Accept customized product, our lithium battery system are widely used in many situations, such as: Different residential home, hotel, shop, factory, hospital, commercial buildings, electric car, RVs, Van, mobile dining car, heavy truck, different ship/boats, ice-cream car, outdoor camper,.etc. Applications: 1.Energy Storage --Solar-Wind Power System / City Grid (On/Off) / Community and Family 2.Back-up System and UPS --Telcom Base / CATV system / Computer Server Center / Medical Instrumnt / Military Equipment 3.Other Applications --Security and Electronics / Mobile POS, Mining Lihgt / Torch / LED Light / Emergency Light --RV Motorhome /Golf Carts Battery / Boat Marine Yachts / Electric Skateboard / Electric bike / Electric Scooter / Electric bicycle --LED Backup / Engine Starting Battery,etc.
MPPT Solar charge controller Feature 1. We choose high speed and high performance 32-bit processor with excellent EMC design 2. Advanced MPPT tracking algorithm, the tracking efficiency more than 99% 3. High performance IGBT power module as electronic switch, there is no any mechanical switch, plus multiphase synchronous rectification technology, improves the stable greatly 4. Ultrafast maximum power point tracking speed to ensure tracking efficiency 5. Accurate identification and tracking of multi-peak maximum power points 6. With current-limiting charging function, charging current can be set, friendly and compatible with various capacity batteries. 7. Widely PV arraysâ?? voltage input, this can save the cost of PV combiner box, wires and construction 8. Full enclosed duct design and high-speed fan for cooling makes the controller suitable for various harsh environment 9. It shows the ambient temperature. It also has automatic temperature compensation function and RTC real time function 10. The perfect battery protection function and multi-stage charging improves battery life 11. It has the statistical function of generating capacity which is very convenient for customers to view the daily, monthly and total charging capacity of the controller. 12. Complete menu display and operation, plus the humanized design of browsing interface, these makes the operation more easy 13. It can work with GEL. LEAD-ACID, LITHIUM and other type battery 14. Twice protection function to protect battery from damage when the power switch is down (optional) 15. Standard Modbus communication protocol for RS-485 or GPRS communication to extend the communication distance (optional function)
SANDI SERIES charging module is for electric vehicle charging station. With single-phase non neutral conductor AC input, it has the advantages of high efficiency, high power density and low harmonic. Functional details 1. Hot plug Plug technology is applied to the charging module to provide convenience for installation and maintenance. The access of the charging module to the system shall not disturb the output voltage of the system. 2. Advanced current sharing technology Under constant voltage working mode, the charging modules can share current automatically within 10S, with degree of unbalance less than �±0.5A. 3. Control of input limited power Refer to Fig. 1-10 for the relation between the output power and input voltage of the charging module. When the input voltage is within 360 Vac ~ 450 Vac (return difference is less than 5V), the module can output the maximum power of 20 KW; when the input voltage is within 260 Vac ~ 320 Vac, the module can still work normally under limited power mode. 4. Control of output constant power When there is a rated input voltage, the output power of the module is 20 KW. Refer to Fig. 11 for the relation between the output voltage and the output current of the module. The SD75050 module uses two operating modes with output voltage ranges of 50 to 750V. The module only selects the operating mode based on the value of the received demand voltage, and does not select the operating mode based on the actual output voltage. 5. Temperature limited power 6. Regulation of output current limiting point 8. Regulation of output voltage The output voltage of the module can be regulated constantly through the external monitoring module, with regulation range of 50Vdc ~ 750Vdc and minimum regulation step of 0.1 Vdc. 9. Fan control The built-in processor of the module can regulate the speed of the fan according to the internal temperature and output current of the module. 10. Protection of input overvoltage/ voltage shortage 11. Output overvoltage protection The overvoltage protection point is 260Vdc ~770Vdc ( +10 Vdc). Default is 778Vdc.The module can be started after manual intervention upon overvoltage protection. 12. Over-temperature protection The environmental over-temperature protection point is 80 C. When the DC panel has a temperature over 100 C, the module will stop working; when the DC panel has a temperature below 90 C, the module will automatically work again. 13. Protection of internal bus fault When the internal bus voltage of the module is beyond the overvoltage/ voltage shortage protection point, the module will be powered off automatically. At this time, there is no output from the module and the fault indicator light is on. 14. Short circuit protection In case of short circuit of the module, it will be subjected to protective shutdown and the red indicator light of the panel is on, and this condition will be transmitted to the monitor of the "module fault".
SANDI SERIES charging module is for electric vehicle charging station. With single-phase non neutral conductor AC input, it has the advantages of high efficiency, high power density and low harmonic. Functional details 1. Hot plug Plug technology is applied to the charging module to provide convenience for installation and maintenance. The access of the charging module to the system shall not disturb the output voltage of the system. 2. Advanced current sharing technology Under constant voltage working mode, the charging modules can share current automatically within 10S, with degree of unbalance less than �±0.5A. 3. Control of input limited power Refer to Fig. 1-10 for the relation between the output power and input voltage of the charging module. When the input voltage is within 360 Vac ~ 450 Vac (return difference is less than 5V), the module can output the maximum power of 20 KW; when the input voltage is within 260 Vac ~ 320 Vac, the module can still work normally under limited power mode. 4. Control of output constant power When there is a rated input voltage, the output power of the module is 20 KW. Refer to Fig. 11 for the relation between the output voltage and the output current of the module. The SD75200 module uses two operating modes with output voltage ranges of 50 to 750V. The module only selects the operating mode based on the value of the received demand voltage, and does not select the operating mode based on the actual output voltage. 5. Temperature limited power 6. Regulation of output current limiting point 8. Regulation of output voltage The output voltage of the module can be regulated constantly through the external monitoring module, with regulation range of 50Vdc ~ 750Vdc and minimum regulation step of 0.1 Vdc. 9. Fan control The built-in processor of the module can regulate the speed of the fan according to the internal temperature and output current of the module. 10. Protection of input overvoltage/ voltage shortage 11. Output overvoltage protection The overvoltage protection point is 260Vdc ~770Vdc (�±10 Vdc). Default is 778Vdc.The module can be started after manual intervention upon overvoltage protection. 12. Over-temperature protection The environmental over-temperature protection point is 80�°C. When the DC panel has a temperature over 100�°C, the module will stop working; when the DC panel has a temperature below 90�°C, the module will automatically work again. 13. Protection of internal bus fault When the internal bus voltage of the module is beyond the overvoltage/ voltage shortage protection point, the module will be powered off automatically. At this time, there is no output from the module and the fault indicator light is on. 14. Short circuit protection In case of short circuit of the module, it will be subjected to protective shutdown and the red indicator light of the panel is on, and this condition will be transmitted to the monitor of the "module fault".
SANDI SERIES charging module is for electric vehicle charging station. With single-phase non neutral conductor AC input, it has the advantages of high efficiency, high power density and low harmonic. Functional details 1. Hot plug Plug technology is applied to the charging module to provide convenience for installation and maintenance. The access of the charging module to the system shall not disturb the output voltage of the system. 2. Advanced current sharing technology Under constant voltage working mode, the charging modules can share current automatically within 10S, with degree of unbalance less than �±0.5A. 3. Control of input limited power Refer to Fig. 1-10 for the relation between the output power and input voltage of the charging module. When the input voltage is within 360 Vac ~ 450 Vac (return difference is less than 5V), the module can output the maximum power of 20 KW; when the input voltage is within 260 Vac ~ 320 Vac, the module can still work normally under limited power mode. 4. Control of output constant power When there is a rated input voltage, the output power of the module is 20 KW. Refer to Fig. 11 for the relation between the output voltage and the output current of the module. The SD75050 module uses two operating modes with output voltage ranges of 50 to 750V. The module only selects the operating mode based on the value of the received demand voltage, and does not select the operating mode based on the actual output voltage. 5. Temperature limited power 6. Regulation of output current limiting point 8. Regulation of output voltage The output voltage of the module can be regulated constantly through the external monitoring module, with regulation range of 50Vdc ~ 750Vdc and minimum regulation step of 0.1 Vdc. 9. Fan control The built-in processor of the module can regulate the speed of the fan according to the internal temperature and output current of the module. 10. Protection of input overvoltage/ voltage shortage 11. Output overvoltage protection The overvoltage protection point is 260Vdc ~770Vdc (�±10 Vdc). Default is 778Vdc.The module can be started after manual intervention upon overvoltage protection. 12. Over-temperature protection The environmental over-temperature protection point is 80�°C. When the DC panel has a temperature over 100�°C, the module will stop working; when the DC panel has a temperature below 90�°C, the module will automatically work again. 13. Protection of internal bus fault When the internal bus voltage of the module is beyond the overvoltage/ voltage shortage protection point, the module will be powered off automatically. At this time, there is no output from the module and the fault indicator light is on. 14. Short circuit protection In case of short circuit of the module, it will be subjected to protective shutdown and the red indicator light of the panel is on, and this condition will be transmitted to the monitor of the "module fault".
SANDI SERIES charging module is for electric vehicle charging station. With single-phase non neutral conductor AC input, it has the advantages of high efficiency, high power density and low harmonic. Functional details 1. Hot plug Plug technology is applied to the charging module to provide convenience for installation and maintenance. The access of the charging module to the system shall not disturb the output voltage of the system. 2. Advanced current sharing technology Under constant voltage working mode, the charging modules can share current automatically within 10S, with degree of unbalance less than �±0.5A. 3. Control of input limited power Refer to Fig. 1-10 for the relation between the output power and input voltage of the charging module. When the input voltage is within 360 Vac ~ 450 Vac (return difference is less than 5V), the module can output the maximum power of 20 KW; when the input voltage is within 260 Vac ~ 320 Vac, the module can still work normally under limited power mode. 4. Control of output constant power When there is a rated input voltage, the output power of the module is 20 KW. Refer to Fig. 11 for the relation between the output voltage and the output current of the module. The SD75050 module uses two operating modes with output voltage ranges of 50 to 750V. The module only selects the operating mode based on the value of the received demand voltage, and does not select the operating mode based on the actual output voltage. 5. Temperature limited power 6. Regulation of output current limiting point 8. Regulation of output voltage The output voltage of the module can be regulated constantly through the external monitoring module, with regulation range of 50Vdc ~ 750Vdc and minimum regulation step of 0.1 Vdc. 9. Fan control The built-in processor of the module can regulate the speed of the fan according to the internal temperature and output current of the module. 10. Protection of input overvoltage/ voltage shortage 11. Output overvoltage protection The overvoltage protection point is 260Vdc ~770Vdc (�±10 Vdc). Default is 778Vdc.The module can be started after manual intervention upon overvoltage protection. 12. Over-temperature protection The environmental over-temperature protection point is 80�°C. When the DC panel has a temperature over 100�°C, the module will stop working; when the DC panel has a temperature below 90�°C, the module will automatically work again. 13. Protection of internal bus fault When the internal bus voltage of the module is beyond the overvoltage/ voltage shortage protection point, the module will be powered off automatically. At this time, there is no output from the module and the fault indicator light is on. 14. Short circuit protection In case of short circuit of the module, it will be subjected to protective shutdown and the red indicator light of the panel is on, and this condition will be transmitted to the monitor of the "module fault".
Technical Features: 1, The core components are all imported, adopting the sixth generation IPM module from Mitsubishi, which has stable performance, long service life, strong protection functions and convenient replacement and maintenance. 2, Adopt the central processor DSP28335 chip from American TI Company, respond quickly and accurately, and provide stable and clean power for the load to provide protection. 3, The whole machine adopts modular design and plug-in design, which is convenient for maintenance. 4, According to the product configuration conditions, adjustment the system usage mode: DC(Battery/Solar) priority or AC mains bypass priority can be set. 5, Two kinds of start mode: Reduction Voltage Start and Variable Frequency Start. Customers can set start mode according to the type of their load. 6, The output voltage can be set between -40 % to +20 % of rated voltage. And the output voltage is very accuracy �±1%. 7, The DC input voltage range can be set. Over-voltage point, under-voltage point, over-voltage recovery point, under-voltage recovery point all can be setting via the LCD panel. 8, Output AC Power is suitable for all types of electrical equipment, CNC machines, electric tools, motors, pump and air conditioner etc. It has higher efficiency and higher capability of driving load. 9, Humanized safety design, using isolation transformer design, input and output are completely electrically isolated, input and output are equipped with circuit breakers, which saving costs for the user and easy to installation, the electric parts are completely closed to prevent electric shock. 10, Using SVPWM space vector algorithms, high conversion efficiency, high instantaneous power and low losses conversion efficiency up to 94%. 11, Powerful data display function. LCD + LED display, can display input and output voltage, current, KWH, fault display, convenient for customers to quickly find faults and guide maintenance. 12, The controller adopts three charging stages (buck charging, equalize charging and float charging) which can maximize the utilization of photovoltaic modules and batteries 13, Solar controller adopt IGBT Modular design ensure stable and efficiency performance of solar controller and solar power system 14, The controller has perfect battery protection function and with multi-stage charging technology to improve battery life 35% at least 15, Fully enclosed duct design and high-speed fan for cooling makes the controller working under harsh environments 16, The controller has power generation statistics and real-time power curve function, so we can know power generating information at any time 17, Colorful LCD display, touching key and multi-language option makes the HMC (Human Machine communication) easy and convenient. 18, The controller also has temperature compensation function and RTC real time clock function,
SANDI SERIES charging module is for electric vehicle charging station. With single-phase non neutral conductor AC input, it has the advantages of high efficiency, high power density and low harmonic. Functional details 1. Hot plug Plug technology is applied to the charging module to provide convenience for installation and maintenance. The access of the charging module to the system shall not disturb the output voltage of the system. 2. Advanced current sharing technology Under constant voltage working mode, the charging modules can share current automatically within 10S, with degree of unbalance less than �±0.5A. 3. Control of input limited power Refer to Fig. 1-10 for the relation between the output power and input voltage of the charging module. When the input voltage is within 360 Vac ~ 450 Vac (return difference is less than 5V), the module can output the maximum power of 20 KW; when the input voltage is within 260 Vac ~ 320 Vac, the module can still work normally under limited power mode. 4. Control of output constant power When there is a rated input voltage, the output power of the module is 20 KW. Refer to Fig. 11 for the relation between the output voltage and the output current of the module. The SD75050 module uses two operating modes with output voltage ranges of 50 to 750V. The module only selects the operating mode based on the value of the received demand voltage, and does not select the operating mode based on the actual output voltage. 5. Temperature limited power 6. Regulation of output current limiting point 8. Regulation of output voltage The output voltage of the module can be regulated constantly through the external monitoring module, with regulation range of 50Vdc ~ 750Vdc and minimum regulation step of 0.1 Vdc. 9. Fan control The built-in processor of the module can regulate the speed of the fan according to the internal temperature and output current of the module. 10. Protection of input overvoltage/ voltage shortage 11. Output overvoltage protection The overvoltage protection point is 260Vdc ~770Vdc (�±10 Vdc). Default is 778Vdc.The module can be started after manual intervention upon overvoltage protection. 12. Over-temperature protection The environmental over-temperature protection point is 80�°C. When the DC panel has a temperature over 100�°C, the module will stop working; when the DC panel has a temperature below 90�°C, the module will automatically work again. 13. Protection of internal bus fault When the internal bus voltage of the module is beyond the overvoltage/ voltage shortage protection point, the module will be powered off automatically. At this time, there is no output from the module and the fault indicator light is on. 14. Short circuit protection In case of short circuit of the module, it will be subjected to protective shutdown and the red indicator light of the panel is on, and this condition will be transmitted to the monitor of the "module fault".
Novatec a271sb/f372sb hubs, front: 2 sealed bearings, o.L.D: 100mm weight: 112g, rear: 4 sealed bearings, o.L.D: 130mm weight:276g Cassette body: shimano or campagnolo Pillar aero 1432 spokes Accessories:free quick release+brake pads +extension valve +rim tapes+6 spare spokes 3k matte/glossy, f-20holes, r-24holes 12-layer design on brake track6-layer carbon body Max recommend rider weight:110kg Max recommend tyre pressure:125psi Weight:1740
Hindalco produces di-ammonium phosphate (DAP) fertiliser. It is the most popular phosphatic fertiliser because of its high nutrient content and good physical properties. The composition of DAP is 18% Nitrogen and P2O5 46%. Within the same facility, Hindalco can also produce nitrogen phosphorus potassium (NPK) complexes as value-added downstream products. It can manufacture NPK complexes such as 10:26:26, 12:32:16 and 20:20:0. Hindalcoâ??s DAP plant went on-stream in the year 2000, and has a capacity of 400,000 TPA. Phosphoric acid is produced at Hindalco's phosphoric acid plant by the chemical reaction of sulphuric acid (generated as by-product from copper smelting process) and rock phosphate (imported). At the DAP plant, phosphoric acid and ammonia are reacted to form DAP. Imported potash is used to produce the NPK complexes. The products are marketed under the well-known brand Birla Balwan, a name that commands preference among the farmers of Gujarat, Maharashtra, Rajasthan, Madhya Pradesh, Chhattisgarh, Haryana and Punjab, through a vast, established network of dealers, retailers and C&F agents. Operations are carried out through both private and institutional distribution channels. The products are packed in gusseted Lyril-green 50kg PP bags, and are transported to various destinations by rail and road, stored and then delivered to dealers, retailers, co-operative societies, and other customers in various marketing regions. The customers are serviced through an experienced and qualified marketing team across all the seven states. Marketing, service-related activities, and farmer/retailer meets are regularly held at customersâ?? locations by well-trained field personnel. Birla Phospho Gypsum is marketed in the agricultural field as a soil conditioner. The product contains 15-17 % sulphur, 20-22 % calcium and 1 % of P2O5. It is an economical input that adds nutrients to the soil and enhances its productivity, improvement and crop growth. Birla Phospho Gypsum is available in loose form, bulk and also in bags for convenience of handling and storage. The popular brand, Birla Vishwas, caters to the market of diversified agricultural inputs
Barley for animal Specifications: Moisture: 14% max Protein: 11.5% min Test weight: 650 g/L max Foreign matter: 0/75 % max Broken kernels: 1.5% max Head damaged kernels: 0.5% max Total damaged kernels: 1% max
Details: Serial n¦ 61683 speed - 225 nominal width - 3300mm useful width - 3200mm needle set - 1020d/1 warps - 6 motor power - 3kw galgaö - 7-14-7 3 jacquards with 1344 hooks each creel û 3600 bobbins maximum serial n¦ 63687 / 71302 speed - 225 nominal width - 3300mm useful width - 3200mm needle set 1020d/1 warps - 6 motor power - 3kw galgaö - 9-18-9 3 jacquards with 1344 hooks each creel û 3456 bobbins maximum, model: rjg 5/2 f-ne.
We specialise in providing a comprehensive range of bicycle parts to meet all your needs. Here's a list of the various bicycle parts we supply: 1. Frames 2. Forks 3. Handlebars 4. Grips 5. Saddles 6. Chain 7. Wheels 8. Tires and Tubes 9. Brakes (including calipers, pads, and levers) 10. Drivetrain components (including chainrings, chains, cassettes, and derailleurs) 11. Pedals 12. ChainWheel & Cranksets 13. Bottom brackets 14. Headsets 15. Shifters 16. Cables and housing 17. Bearings and bushings 18. Reflectors and lights 19. Fenders 20. Kickstands 21. Bottle cages 22. Bike locks 23. Bike racks and carriers 24. Tools and maintenance equipment 25. Bicycle carrier 26. Bicycle paddle 27. Axle 28. Fork fitting 29. Mudguard 30. Coaster Brake 31. Chain wheel cover 32. Bicycle bell And many more. No matter what type of bicycle part you're looking for, we have you covered with high-quality products to enhance your cycling experience.
INGREDIENT SPECIFICATION: Canola Oil, NOP Refined, Bleached and Deodorized CERTIFICATE OF ANALYSIS: Each shipment to include certificate. DESCRIPTION: Organic Canola seeds are pressed using cold-pressing technology, degummed, bleached (if necessary), and deodorized under vacuum and controlled temperature. APPEARANCE, FLAVOR & COLOR Light green in color with light taste AVERAGE ANALYSIS: IODINE VALUE: 100 130 PEROXIDE VALUE: 1.00 Max. FATTY ACID COMPOSITION: FREE FATTY ACID Max. 0.10% of Oleic Acid MYRISTIC ACID C 14:0 0.20 % Max. PALMITIC ADIC C 16:0 3.0 â?? 6.0 % PALMITOLEIC ACID C 16:1 0.60 % Max. STEARIC ACID C 18:0 1.0 3.0 OLEIC ACID C 18:1 51 70 % LINOLEIC ACID C 18:2 15 30 % LINOLENIC ACID C 18:3 5 15 % ARACHIDIC ACID C 20:0 0.2 1.2 % EICOSENOIC ACID C 20:2 0.1 3.0 % BEHENIC ACID C 22:0 0.5 % Max. ERUCIC ACID C 22:1 2.0 % Max. STORAGE: Store in a cool dry place away from direct sources of sunlight, heat, and oxidizers. Properly stored unopened containers have an expected shelf life of 24 months. MARKINGS: As per the buyer specification suggested:; COUNTRY OF ORIGIN MANUFACTURER IMPORTER BATCH NUMBER PURCHASE ORDER NUMBER JULIAN DATE PACKAGING: Drums (55 gallon) or any DOCUMENTS: Lot or batch numbers Date of Manufacture Certificate of Analysis Kosher Certificate, if required Organic Certificate
Organic High Oleic Sunflower is a vertical Organic Process, our supplier chooses the organic seeds that need to be crushed, they then oversee the crushing of the seeds into a liquid. Additionally, a large ORGANIC refinery processes the oil into the finished High Oleic Sunflower we bring to market. Important controls and specification are followed by an extensive QA/QC team to insure quality and ORGANIC status. DESCRIPTION New hybrids of the traditional sunflower species produce an oil unusually high in oleic acid (C18:1). The appearance of this new hybrid only differs in the color of the kernel shells from off white to silver gray compared to black resp. black stripes. The seed is pressed and then extracted. The subsequent 4 step refining (deacidification, bleaching, steam deodorization, and winterization) results in a very light transparent refined high oleic sunflower seed oil with excellent oxidative stability. ORIGIN: The Netherlands and France CERTIFICATE OF Each shipment to include certificate. ANALYSIS: APPEARANCE & COLOR Appearance: Light transparent / Color: Lovibond 5 14 2.0 red SPECIFICATIONS Density (20 C) 0.912 -0.924 Refractive Index (20 C) 1.464 -1.474 Iodine Value 80-97 Peroxide Value 1.00 max Saponification Value 187 â?? 197 Smoke Point ca. 240�° C Free Fatty Acids (% of Oleic Acid) 0.10 max FATTY ACID COMPOSITION Palmitic Acid C 16:0 5.0 % max Stearic Acid C 18:0 6.2 % max Oleic Acid C 18:1 75 â?? 90 % Linoleic Acid C 18:2 17 % max Linolenic Acid C 18:3 0.3% max Arachidic Acid C 20:0 0.69 % max Behenic Acid C 22:0 1.6 % max Other Fatty Acids 3 % max STORAGE: Keep away from direct sunlight at room temperature in tightly sealed containers (nitrogen topping is of advantage) USAGE: The excellent stability to oxidation is comparable to that of a good olive oil and approximately twice as high as with traditional sunflower oil and soybean oils. It is therefore, particularly suited as a fat component and carrier for pharmaceutical and cosmetic formulations. Its usage in food: in baker's ware and pastries (un-hydrogenated spray oil), baby food and margarines, as a baking and frying oil (high smoke point). Like olive oil, high oleic sunflower seed oil is believed to favorably influence the human cholesterol metabolism due to its high content of monounsaturated oleic acid (C18:1).
We are Brazil Exporter and Importer Certified producers of USA, Brazil, Argentina, UK Halal and non Halal Frozen Chicken. We supply at both CIF and FOB terms at any safe world port. Our product meet both International and National Standards. We can supply various Frozen Chicken cuts such as; We can supply various Frozen Chicken cuts such as; 1. frozen whole chicken 2. frozen chicken feet 3. frozen chicken Paws 4. frozen chicken breast 5. frozen chicken thighs 6. frozen chicken drumstick 7. frozen chicken leg quatars 8. frozen chicken wings We ship directly to all Asian ports, and we are registered to supply and deliver directly to China, Hong Kong, Vietnam,dubai,saudi, Taiwan, Korea, Thailand , Malaysia and other countries.. we produce and supply the best quality of Grade A Frozen Chicken Feet,Paws and other chicken parts Processed Frozen Chicken Paws â?? Grade A Specifications: - White skin - No broken bones 0% - Outer yellow skin off - Well cleaned and fresh - No bruises - No black pads or ammonia burns - No bad smells - No excessive blood or blood stains - Moisture content is less than 3% - Weight per piece is 35-50g - Length per piece 12-15 cm Frozen Temperature: - Blasted at: minus 40 degrees Celsius - Storage at: minus 20 degrees Celsius. - Temperature during Transportation: minus 18 degrees Celsius We package in 20kg carton boxes, each box contains 5kg polybags x 4. Customized packaging of all other sizes are offered, and we also provide labels for buyers. We load 27MT per container 40FT. Processed Frozen Chicken Feet â?? Grade A Specifications: - White skin - No broken bones 0% - Outer yellow skin off - Well cleaned and fresh - No bruises - No black pads or ammonia burns - No bad smells - No excessive blood or blood stains - Moisture content is less than 3% - Weight per piece is 35-60g - Length per piece 14-16cm Frozen Temperature: - Blasted at: minus 40 degrees Celsius - Storage at: minus 20 degrees Celsius. - Temperature during Transportation: minus 18 degrees Celsius We package in 20kg carton boxes, each box contains 5kg polybags x 4. Customized packaging of all other sizes are offered, and we also provide labels for buyers. We load 27MT per container 40FT
Wholesale Passenger Car PCR Tyre, 4WD Offroad SUV 4X4 at/Mt Mud Tyres, Truck tires, tractor, excavator Sizes: 12.00R20 Type Inner Tube Structure All-steel radial Position steer/all position Application Off road Features: Wider tread, High speed, low rolling resistance, excellent wet grip etc. Place of Origin China Loading Port Qingdao Certificates: ECE, etc. OEM Yes Supply Ability: 7 million pieces per Year Min. Order: 1*20 GP HS Code: 40112000 Technology: German Technology Quality warranty: 120000� km Shipment Date: Within 15 days after deposit Package: Standard package for exporting Supplier Star Rating: Top five stars
