* PHOSCAST Phoscast : Phosphate Bonded Castables * PURPOSE customers using FBC boilers (Particularly underbed feed FBC boilers) for the protection of inbed coils against erosion potential by applying highly abrasive resistant refractory on inbed coils above fuel feed system. BACKGROUND * Two of such actions are providing special alloy studs on inbed coils and applying highly abrasive resistant refractory on the outer bottom loops of inbed Coils which are above the fuel feed nozzles. * GANESHAS has taken number of approaches to identify the key factors affecting erosion rates with an objective to enhance the life of inbed tubes as well as implementing the corrective action to reduce the erosion rates. Phosphate coatings are often used to protect steel parts against rusting and other types of corrosion * Erosion of inbed coils in fluid bed combustor is unavoidable phenomenon however the rate of metal wastage and thus the life of tubes depends on various factors like ash & fuel properties, design of Combustor / feeding system, flue gas velocities operating conditions etc. It has been also observed that maximum erosion prone inbed coils are those which come above fuel feed nozzles and an area of approximately 1 to 1.5 mts around fuel feed systems are badly affected. APPLICATION Phoscast-90 XR can be applied by ramming with wooden mallet having adequately large head @" dia x 5" length x 10â?? Jong handle). The desired lining or repair thickness is built up in several courses while ramming the mass to uniform thickness. Phoscast refractory should never be trawled to obtain smooth surface; ramming only should finish surface. Any excess mass is to be sliced off with trowel edge and then finished by ramming again for bed coil. Tube application of AFBC boiler, the material pasty mass should be finger pressed into the studs of the tube with maximum force. Finish should be given by pressing the hand palm against material applied, using surgical type thin rubber hand gloves.
Ramming mass is commonly used in metallurgy, building materials, non-ferrous metal smelting, chemical, machinery and other manufacturing industries. Ramming mass is widely used in non-core intermediate frequency furnace and core induction furnace. As an intermediate frequency furnace ramming material, refractory ramming is applied to melt gray cast iron, nodular cast iron, malleable cast iron, vermicular cast iron, and cast alloy steel; to melt carbon steel, alloy steel, high manganese steel, tool steel, heat resistant steel, stainless steel, molten aluminum and its alloys; to melt red copper, brass, white brass, bronze and its alloys, etc. Induction furnaces are used for melting cast iron, mild steel and various alloy steels in foundries and making of steel in mini steel plants using sponge iron The refined high silicon, low iron quartz sand and quartz powder are selected and the fused quartz sand is added as the refractory material., with no slag, no crack, damp proof, convenience of repair, and the corrosion resistance, thus greatly improving the furnace service life span and the economic benefit.. Silica ramming mass can safely be used up to an operating temperature of 1600 deg C. Since it expands very little, it is superior to both alumina and magnesia refractories to resist thermal shocks Acid ramming material is the premixed ramming mass of the lining material. The acid ramming mass is used to smelt a series of metal materials such as ordinary steel and carbon steel. The lining practice best suited to a particular furnace depends upon the capacity and design of the furnace, operation practice adopted during making of a heat, and furnace output.
METHOD OF APPICATION: * Mastic compound application consist of two coats of. Primer ,Primer and followed by Mastic compound in recommended thickness, ranging from min. 12mm to 25mm in one or two layers to achieve desired thickness without any pin hole and crack. 1). Surface preparation and application of Primer: Refer application method of Primer. 2). After doing necessary surface preparation and application of primer coating, area to be installed with Mastic compound should be divided in to equal no. bays. To maintain even thickness required, place wooden or aluminum batten. Mastic compound is then broken in small pieces and put it in heating pan. While heating, keep material moving to avoid burning. It is heated until it comes in a uniform consistency and then applied on the surface and works it with wooden float, to achieve uniform thickness and smooth surface free from any pinholes. CHEMICAL RESISTANCE PROPERTIES: * Mastic compound has good resistance to weak, diluted acids, alkalis salts etc. It is not recommended to use against strong acids, oxidizing acid solvents, oil and fats STORAGE & PACKING: * Keep Mastic compound away from direct sunlight, heat solvents etc. Under this condition, its shelf life is unlimited. It is supplied in cake form and approx. wt. is 10 kgs. HEALTH & SAFETY: * Handle melted Mastic compound compound very carefully . Avoid contact with skin. It is advisable to wear protective wears at the time of use of Mastic compound and all other our products. This information, given in good faith, is based on results gained from experience and tests. However, all recommendations or suggestions are made without guarantee since the conditions of use are beyond our control.
APPLICATION OF SK-HB K-SILICATE MORTAR : * K-SILICATE is used for jointing Acid Resisting brick in construction of vessels in suited for construction of fume chambers and stacks handling hot, dry Acid fumes and vapors. It is also used for jointing chemical resisting stoneware pipes. K-SILICATE cement is good bedding material for Acid â?? Resisting bricks and tiles. The concrete surface needed protection should be dryed, clean and rough. The bricks or tiles will be set with K-SILICATE cement over concrete surface applied with a suitable an impermeable interliner. When Bedding and Jointing Materials are the same. On the treated surface bricks or tiles are bedded to a thickness of about 6 mm and tamp gently with a wooden piece till the paste squeezes out of joints. The paste that is squeezed out of the joint should be removed by trowel with good finishing. After the mortar of the joint is dryed treat the joints with 20% Hydrochloric Acid Solution by means of brush. A.R.lining should be always in contact with Acid and not with water. Concrete subtract like Floor, Wall, tanks and similar surface should be protected with a membrane of Bitrok Mastic or compound steel tanks should be protected with rubber or PVC subjected to chemical conditions and temperature of chemical media. The Brick lining is recommended over the protective layer of Bitrok Mastic. When Bedding and Jointing Materials are Different. Spread the silicate type mortar about 6 to 8 mm thick on the back of the tile or brick. Press the tile on the bed leaving required space for joints between tiles for bricks. After the bedding mortar is set, fill Mp the joints with specified cement.PRODUCT DATA SHEET FOR SK-HB ( K-SILICATE) MORTAR A general purpose cement for acid conditions Resistant to High & medium concentrations of most of the common organic and inorganic acids except Hydroflouric acid. Recommended where the concentration of the acid is high suitable for high temperature. Unsuited to aqueous solutions, alkaline conditions. PREPARATIONS OF MORTAR : * Measure 1 part by weight of K-SILICATE solution into a suitable mixing pan. * Add slowly and gradually 3 parts by weight K-SILICATE mortar and mix thoroughly to form a smooth mortar. * In hot season very large batches of mortar will become stiff quite rapidly therefore small batches, not exceeding 4 to 8 kgs. Will be prepared. * The cement mortar will be used before it starts setting.
This is chemical setting Furan based chemical resistant mortar which is combination of Liquid and Powder, when mixed in proper proportion from workable mortar which after setting and curing give of liquid and give black highly cross linked composites. Furan When set and cured is resistant to highly corrosive acids, alkalis and to powerful organic solvents such as ketones, Aromatic and Chlorinated solvents. It has extreme resistant to Acidic & alkalis, Salts, Greases and Detergents. It resists to Organic & Inorganic acids at their boiling temperature. It is suitable against mild chlorine Gas (dry) phosphorous trichloride, pyridine at room temperature. Furan is especially useful where resistance to mixed media such as aqueous acids /alkalis and organic solvents is needed in chemical plant process and waste streams. Carbon filled Furan is used against corrosive effect of hydrofluoric acid & its salts. PREPARATION OF FURANE MORTAR : Mortar consist of Furan solution and Furan powder. The average mixing ratio necessary to obtain mortar with good working consistency is 1 part by weight Solution & 3 part by weight powder. The ratio will vary slightly depending on temperature and working conditions.Stir the liquid thoroughly before using. Place liquid in a suitable shallow mixing pan. Add powder by weight in the solution mix thoroughly and rapidly until all lumps are dispersed and the mortar is completely homogenous. Spread out the mortar in a thin layer, not more than ¾ thick, to dissipate the heat of reaction and lengthen the working life. Batch size can be varied depending upon the temperature and the speed with which the masons are working. Very large batches will become stiff quite rapidly. Make sure that all the Furan Motrar is used from the pan before another batch is mixed.When working at temperature above 40 C, very small batches not more than 2 Kgs, should be prepared. When working at temperature below 15C the liquid should be kept warm.
PRODUCT DATA SHEET ACID RESISTANT BRICK Material : RED SHALE Type Acid Resistant Brick Size (mm) 230 (LENGTH) X 115 (WIDTH) X 100,76,65,50,40,38,30,25 (THICK) Specification : ASTM C279, ASTM C410, IS 4860-1982 DESCRIPTION : We offer premium quality acid resistant bricks Red â?? Shale , tiles and special shapes. We also offer customized sizes as per clients' requirements. Our acid bricks comply with ASTM C279 Type-III, ASTM C410 Type H, L, and Indian Standard 4860 - 1982 Class-I for all applications where low absorption and high acid resistance is required. FEATURES OF ACID RESISTANT BRICK: Excellent resistant against wide range of chemicals except hydrofluoric acid, high abrasion resistance, low wearing properties, High Thermal resistant to sudden change in temperature AREA OF APPLICATION: Chemical Analysis (Average) Acid and Alkali Storage Tank Farms Demineralization plants and Water treatment plants Chimney inside lining, FGD linings Towers and Columns Process Vessels and Tanks Sewerage Treatment Plants and Lines Industrial Flooring and Bund Areas Chimney and Flue Gas Linings Hoppers and Chutes SiO266.4 Al2 0324 TiO21.1 Fe2 O31.1 K2 O + Na2 O2.5 NOT RECOMMENDED: HF acid or other fluoride solutions Heavy thermal shock Typical Physical Properties of GANESHAS Acid and Chemical Resistant Brick Characteristic RED SHALE ACID RESISTANT BRICK Test Standard Bulk Density, gm/cc - 2.3 to 2.35 ASTM C-20 -Water Absorption, % - 0.1 to 1.5 IS 4860-1968 Apparent Porosity, % -0.5 to 1.75 S 4860 Acid Solubility (H2SO4), Loss in Mass,% -0.1 to 1.8 ASTM C-279 Modulus of Rupture, PSI -2133 to 3555 ASTM C-67 Compressive Strength, Kg/cm2 - 700-900 IS 4860-1968 Abrasion Resistant , Volume in mm3 -69 to 85 EN 102 Surface Hardness, MOHS Scale - 7
PRODUCT DATA SHEET ACID RESISTANT BRICK Material : FIRECLAY Type Acid Resistant Brick Size (mm) : 230 (LENGTH) X 115 (WIDTH) X 100,76,65,50,40,38,30,25 (THICK) Specification : ASTM C279, ASTM C410, IS 4860-1982 DESCRIPTION : * We offer premium quality acid resistant bricks Red â?? Shale , tiles and special shapes. We also offer customized sizes as per clients' requirements. Our acid bricks comply with ASTM C279 Type-III, ASTM C410 Type H, L, and Indian Standard 4860 - 1982 Class-I for all applications where low absorption and high acid resistance is required. FEATURES OF ACID RESISTANT BRICK: * Excellent resistant against wide range of chemicals except hydrofluoric acid, high abrasion resistance, low wearing properties, High Thermal resistant to sudden change in temperature AREA OF APPLICATION: Chemical Analysis (Average) Acid and Alkali Storage Tank Farms Demineralization plants and Water treatment plants Chimney inside lining, FGD linings Towers and Columns Process Vessels and Tanks Sewerage Treatment Plants and Lines Industrial Flooring and Bund Areas Chimney and Flue Gas Linings Hoppers and Chutes SiO266.4 Al2 0324 TiO21.1 Fe2 O31.1 K2 O + Na2 O2.5 NOT RECOMMENDED: HF acid or other fluoride solutions - Heavy thermal shock Characteristic Fireclay Type Acid Resistant Brick - Test Standard Bulk Density, lbs/ft3 - 2.25 to 2.30 ASTM C-20 Water Absorption, % - 0.1 to 1.8 ASTM C-20 Apparent Porosity, % - 4.05 to 4.14 ASTM C-20 Acid Solubility (H2SO4), Loss in Mass,% - 6.1 to 6.8 ASTM C-279 Modulus of Rupture, Mpa - 14.6 ASTM C-67 Compressive Strength, PSI - 15500 to 17250 ASTM C-67 Abrasion Resistant , Volume in mm3 - 71 to 96 EN 102 Surface Hardness, MOHS Scale - 7 Thermal Conductivity, BTU-in/hr-ft-F - 6.94 to 7.12 ASTM C-236 Thermal Expansion Coefficient,in/in/Fx10-6 - 2.6 to 2.8 EN 103
Acid / Alkali Resistant Tiles/Bricks * Our Acid proof tiles, Acid alkali resistant tiles, Chemical resistant tiles are fully vitrified tiles which are manufactured using special non ferrous clay, processed at extremely high temperatures this process causes the raw materials to fuse and form a compact mass with an extremely low water absorption of less than 0.5% resulting in the formation of a very strong body with a flexural strength of 38 N/mm2, solid through color fade proof with a very hard surface Mohs hardness of 7. * The acid resistant tiles come in a range of sizes and thicknesses from ranging from 8-25mm. Our acid proof tiles meet stringent specification norms of IS 4457:2007 and relevant ASTM/DIN standards which ensure excellent performance in Acid/Alkali/Chemical (expect Hydrofluoric acid and its derivatives). Corrosion Protection Applications * Factory Floors subject to corrosion from Chemicals, Acids, Oil & Solvents * Pickling tank and surrounding areas * Food & Beverage Industry flooring * Battery rooms and Control rooms * Demineralization plants * Walls of washing and Paint shop areas * Acid Resistant Tiles Manufacturers India * Our acid proof tiles provide excellent abrasion resistance, anti-skid properties for worker safety and high aesthetic appeal. We also provide specialized corner tiles for reducing chances for acid attack through construction joints. Our standard sizes are 200x100, 200x200 & 300x300 millimeters.
NILKANTH EXPORTS are the leading manufacturers and importers of best quality Sawdust Powder in India The products of Nilkanth Exports are focused to provide our clients a top quality of Sawdust We offer superior quality of Saw Dust than Vietnam and China with low affordable an competitive price We are undoubtedly involved in offering a unique range of Saw Dust that is precisely processed using the most recent techniques jointly with set industrial standards Highly appreciated for their accurate composition and with best quality these products are available in different packaging options according to clientspecific demands Apart from this the offered range is sternly tested against various parameters of quality under the inspection of our adroit experts We are providing a wide range of Brown Wood Sawdust Powder It is available in different quality and quantities as per the demands from our customers Saw Dust is used as Alternative Fuel in Many Industries Moreover our offered products are examined against various parameters under the attention of our top quality controllers to give a flawless array at the users premises Features  Precisely Packed  Long Shelf Life  Exact Composition  High Purity Specification of Saw Dust Alternative Fuel Parameters Results Approx GCV ADB 3600 to 4000 KCalKg Total Moisture 15 to 20 Size 00mm to 10mm
Fly ash is a by-product produced while burning finely ground coal in a boiler to produce electricity. It is removed from the plant exhaust gases primarily by electrostatic precipitators or baghouses and secondarily by scrubber systems. Physically, fly ash is a very fine, powdery material, composed mostly of silica. Nearly all particles are spherical in shape. Fly ash is a pozzolan, a siliceous material which in the presence of water will react with calcium hydroxide at ordinary temperatures to produce cementitious compounds. SiO2, Al2O3, Fe2O3 and occasionally CaO are the main chemical components present in fly ashes. Fly ash significantly improves concrete performance in different ways and also provides many benefits in cement and non-cement applications. Fly Ash colour can vary from grey and dark grey, yellowish tan and light to brownish. ADVANTAGES OF FLY ASH IN CONCRETE Fly Ash is a Pozzolan Improves concrete workability and lowers water demand Sulfate and Alkali Aggregate Resistancet Rise in compressive strength over time Environment friendly CEMENTATION Fly Ash is optimized for its fineness while reducing the water demand and improving the chemical compositions to maximise its benefits when used in concrete. Fly-ash can also be used as an add-on to concrete mixture with pozzolanic and/or latent hydraulic properties. We at CEMENTATION selectively collect fly ash and subject to rigorous testing, further refines these collected materials to produce quality fly ash products meeting the needs of our customers.
Product Description - Mazut is a commercial grade oil Price of product ( USD price or FOB price) - UNFOURTUNALLY OUR NEXT ALLOCATION FOR MAZUT M 100 IS POSSIBALY NEXT MONTH Product origin - Russia Key Specifications/Special Features - Mazut M - 100 is a heavy oil which is used in large boiler's for its high energy content Minimum Order Size and Packaging details - "First initial trial shipment of 10,000 MT, followed by a 12 month contract, with monthly shipments between 25,000 to 100,000 MT per month. SORRY, NO SPOT CONTRACTS ACCEPTED "
1). Size: 25mm*25mm-250mm-250mm 2). Wall thickness: 1.5mm-25mm 3). Length: 1m-12m 4). Grade: Q195, Q235, Q345,SS400,SS540, S235JR, A36 etc 4). Certificate: ISO 9001-2008 5). Packing: Standard exporting package. 6). Delivery: Within 20 days after receiving the deposit. 7). Application: Framework of all kinds of construction and engineering; Construction joint ;Iron tower; Derrick frame ; Building structures, such as beams, bridges, transmission towers, lifting or transporting machines, shipping, industrial boilers ,product according to your needs.
Keywords: Refined Fine Salt Non-Iodized Refined Fine Salt Iodized Refined Fine Salt NACL Edible salt Fine refined iodized salt Refined sodium chloride Refined Iodized Salt Refined Salt sodium chloride salt Fine Salt Food Grade Salt Food Salt iodized salt Non iodized salt Sea Salt Sodium chloride low-sodium salt low-sodium salt (light salt) light salt Table Salt Origin: Egypt Salt source: Sea salt Color and Form: White Crystalline Refined Fine Salt Packing: 25 Kg Sacks - Jumbo Bag 1 Ton Hs Code: 250100 Molecular Formula: NaCl Purity: 98.50% min. Refined Fine Salt Chemical analysis: (Attached) Refined Fine Salt Application: Edible Salt, Food Industry, Boiler Water Treatment, Textile, Leather Tanning Sieve: Passing from 1 mm 90% min.
Description:Stainless Steel Sheet, Cold Rolled Stainless Steel Sheet, Hot Rolled Stainless Steel Sheet Type:201 202 304 316L 310S 309S 321 316Ti 410 420 430 409 duplex,SAF2205,S31803 Thickness:0.3-60mm Width:500-2000mm or customized Length:1000-6000 or customized Standard size:1000-2000mm, 1250-2500mm, 1219-2438mm, 1500-3000mm Surface:2B, No.1, No.4, HL, BA, 8K etc Standard: ASME, ASTM, EN ,BS,GB,DIN, JIS etc Application:Stainless steel sheet applies to construction field, ships building industry, petroleum & chemical industries,war and electricity industries, food processing and medical industry, boiler heat exchanger,machinery and hardware fields.
Description:Stainless Steel Sheet, Cold Rolled Stainless Steel Sheet, Hot Rolled Stainless Steel Sheet Type:201 202 304 316L 310S 309S 321 316Ti 410 420 430 409 duplex,SAF2205,S31803 Thickness:0.3-60mm Width:500-2000mm or customized Length:1000-6000 or customized Standard size:1000-2000mm, 1250-2500mm, 1219-2438mm, 1500-3000mm Surface:2B, No.1, No.4, HL, BA, 8K etc Standard: ASME, ASTM, EN ,BS,GB,DIN, JIS etc Application:Stainless steel sheet applies to construction field, ships building industry, petroleum & chemical industries,war and electricity industries, food processing and medical industry, boiler heat exchanger,machinery and hardware fields.
Description:Stainless Steel Sheet, Cold Rolled Stainless Steel Sheet, Hot Rolled Stainless Steel Sheet Type:201 202 304 316L 310S 309S 321 316Ti 410 420 430 409 duplex,SAF2205,S31803 Thickness:0.3-60mm Width:500-2000mm or customized Length:1000-6000 or customized Standard size:1000-2000mm, 1250-2500mm, 1219-2438mm, 1500-3000mm Surface:2B, No.1, No.4, HL, BA, 8K etc Standard: ASME, ASTM, EN ,BS,GB,DIN, JIS etc Application:Stainless steel sheet applies to construction field, ships building industry, petroleum & chemical industries,war and electricity industries, food processing and medical industry, boiler heat exchanger,machinery and hardware fields.
Description:Stainless Steel Sheet, Cold Rolled Stainless Steel Sheet, Hot Rolled Stainless Steel Sheet Type:201 202 304 316L 310S 309S 321 316Ti 410 420 430 409 duplex,SAF2205,S31803 Thickness: 0.3-60mm Width: 500-2000mm or customized Length: 1000-6000 or customized Standard size: 1000-2000mm, 1250-2500mm, 1219-2438mm, 1500-3000mm Surface:2B, No.1, No.4, HL, BA, 8K etc Standard: ASME, ASTM, EN ,BS,GB,DIN, JIS etc Application: Stainless steel sheet applies to construction field, ships building industry, petroleum & chemical industries,war and electricity industries, food processing and medical industry, boiler heat exchanger,machinery and hardware fields.
Description:Stainless Steel Sheet, Cold Rolled Stainless Steel Sheet, Hot Rolled Stainless Steel Sheet Type:201 202 304 316L 310S 309S 321 316Ti 410 420 430 409 duplex,SAF2205,S31803 Thickness:0.3-60mm Width:500-2000mm or customized Length:1000-6000 or customized Standard size:1000-2000mm, 1250-2500mm, 1219-2438mm, 1500-3000mm Surface:2B, No.1, No.4, HL, BA, 8K etc Standard: ASME, ASTM, EN ,BS,GB,DIN, JIS etc Application:Stainless steel sheet applies to construction field, ships building industry, petroleum & chemical industries,war and electricity industries, food processing and medical industry, boiler heat exchanger,machinery and hardware fields.
Description:Stainless Steel Sheet, Cold Rolled Stainless Steel Sheet, Hot Rolled Stainless Steel Sheet Type:201 202 304 316L 310S 309S 321 316Ti 410 420 430 409 duplex,SAF2205,S31803 Thickness:0.3-60mm Width:500-2000mm or customized Length:1000-6000 or customized Standard size:1000-2000mm, 1250-2500mm, 1219-2438mm, 1500-3000mm Surface:2B, No.1, No.4, HL, BA, 8K etc Standard: ASME, ASTM, EN ,BS,GB,DIN, JIS etc Application:Stainless steel sheet applies to construction field, ships building industry, petroleum & chemical industries,war and electricity industries, food processing and medical industry, boiler heat exchanger,machinery and hardware fields.
Description:Stainless Steel Sheet, Cold Rolled Stainless Steel Sheet, Hot Rolled Stainless Steel Sheet Type:201 202 304 316L 310S 309S 321 316Ti 410 420 430 409 duplex,SAF2205,S31803 Thickness:0.3-60mm Width:500-2000mm or customized Length:1000-6000 or customized Standard size:1000-2000mm, 1250-2500mm, 1219-2438mm, 1500-3000mm Surface:2B, No.1, No.4, HL, BA, 8K etc Standard: ASME, ASTM, EN ,BS,GB,DIN, JIS etc Application:Stainless steel sheet applies to construction field, ships building industry, petroleum & chemical industries,war and electricity industries, food processing and medical industry, boiler heat exchanger,machinery and hardware fields.
