3050X760X12Mm Acrylic Solid Surface Sheet Suppliers and Manufacturers

APPLICATION OF SK-HB K-SILICATE MORTAR : * K-SILICATE is used for jointing Acid Resisting brick in construction of vessels in suited for construction of fume chambers and stacks handling hot, dry Acid fumes and vapors. It is also used for jointing chemical resisting stoneware pipes. K-SILICATE cement is good bedding material for Acid â?? Resisting bricks and tiles. The concrete surface needed protection should be dryed, clean and rough. The bricks or tiles will be set with K-SILICATE cement over concrete surface applied with a suitable an impermeable interliner. When Bedding and Jointing Materials are the same. On the treated surface bricks or tiles are bedded to a thickness of about 6 mm and tamp gently with a wooden piece till the paste squeezes out of joints. The paste that is squeezed out of the joint should be removed by trowel with good finishing. After the mortar of the joint is dryed treat the joints with 20% Hydrochloric Acid Solution by means of brush. A.R.lining should be always in contact with Acid and not with water. Concrete subtract like Floor, Wall, tanks and similar surface should be protected with a membrane of Bitrok Mastic or compound steel tanks should be protected with rubber or PVC subjected to chemical conditions and temperature of chemical media. The Brick lining is recommended over the protective layer of Bitrok Mastic. When Bedding and Jointing Materials are Different. Spread the silicate type mortar about 6 to 8 mm thick on the back of the tile or brick. Press the tile on the bed leaving required space for joints between tiles for bricks. After the bedding mortar is set, fill Mp the joints with specified cement.PRODUCT DATA SHEET FOR SK-HB ( K-SILICATE) MORTAR A general purpose cement for acid conditions Resistant to High & medium concentrations of most of the common organic and inorganic acids except Hydroflouric acid. Recommended where the concentration of the acid is high suitable for high temperature. Unsuited to aqueous solutions, alkaline conditions. PREPARATIONS OF MORTAR : * Measure 1 part by weight of K-SILICATE solution into a suitable mixing pan. * Add slowly and gradually 3 parts by weight K-SILICATE mortar and mix thoroughly to form a smooth mortar. * In hot season very large batches of mortar will become stiff quite rapidly therefore small batches, not exceeding 4 to 8 kgs. Will be prepared. * The cement mortar will be used before it starts setting.

Oxidized starch - TS is a Chemically Modified, Vegan, Gluten-Free, Plant-based, Non-GMO tapioca starch. Oxidized starch is characterized by its exceptional functional properties such as low viscosity, high stability, clarity, film forming, low temperature stability and binding properties. Oxidized starch is widely used in bakery products, frozen foods, dairy products, confectioneries, breading and coating applications, etc., It is 100% naturally made which does not have any preservatives and Mono sodium Glutamate (MSG). APPLICATIONS Oxidized starch is used as stabilizer in milk products, ice cream desserts, puddings, fillings, etc.,It is also used in the production of flavoured yoghurts, flavoured milk drinks, whipped cream, low fat cream, etc., Oxidized starch can also be used as fat-mimetic and partial replacement of casein in cheese products with improved stretchability and hardness Oxidized starch is recommended for salad and vegetable sauces, salad dressings, sugar syrups, sauces for canned meat and vegetables, mayonnaise, soups, puddings, fruit filling for confectionery products, jellies, fruit paste candy and soft gummies In baking industry, Oxidized starch expands and improve physical possessions and physical properties of dough, increases its capability to hold gases FROZEN FOODS Oxidized starch is used in frozen foods, refrigerated or canned foods, generally for thickening, temperature stability and control the flow in the purpose food. Oxidized starches are used for improved adhesion and improved stability, reputedly because of covalent bonding with protein on the substrate surface. FEATURES AND BENEFITS Oxidized starch has improved solubility and paste clarity and could be an alternative source for food products requiring high solid contents without over-thickening It is highly bio-degradable and causes no harm to the Environment. Oxidized starch is a White powder that adds no color to application and blends well with other ingredients. It has a bland taste and so will not mask flavors or aromas.

EnzoPlast TS 8 is a Chemically Modified, Vegan, Gluten-Free, Plant- based, Non-GMO oxidized tapioca starch. EnzoPlast TS 8 is characterized by its exceptional functional properties such as low viscosity, high stability, clarity, film forming, low temperature stability and binding properties. EnzoPlast TS 8 is widely used in bakery products, frozen foods, dairy products, confectioneries, breading and coating applications, etc., It is 100% naturally made which does not have any preservatives and Mono sodium Glutamate (MSG). APPLICATIONS EnzoPlast TS 8 is used as stabilizer in milk products, ice cream desserts, puddings, fillings, etc.,It is also used in the production of flavoured yoghurts, flavoured milk drinks, whipped cream, low fat cream, etc., EnzoPlast TS 8 can also be used as fat-mimetic and partial replacement of casein in cheese products with improved stretchability and hardness EnzoPlast TS 8 is recommended for salad and vegetable sauces, salad dressings, sugar syrups, sauces for canned meat and vegetables, mayonnaise, soups, puddings, fruit filling for confectionery products, jellies, fruit paste candy and soft gummies In baking industry, EnzoPlast TS 8 expands and improve physical possessions and physical properties of dough, increases its capability to hold gases FROZEN FOODS EnzoPlast TS 8 is used in frozen foods, refrigerated or canned foods, generally for thickening, temperature stability and control the flow in the purpose food. EnzoPlast TS 8 are used for improved adhesion and improved stability, reputedly because of covalent bonding with protein on the substrate surface. FEATURES AND BENEFITS EnzoPlast TS 8 has improved solubility and paste clarity and could be an alternative source for food products requiring high solid contents without over-thickening It is highly bio-degradable and causes no harm to the Environment. EnzoPlast TS 8 is a White powder that adds no color to application and blends well with other ingredients. It has a bland taste and so will not mask flavors or aromas.

Acid / Alkali Resistant Tiles/Bricks * Our Acid proof tiles, Acid alkali resistant tiles, Chemical resistant tiles are fully vitrified tiles which are manufactured using special non ferrous clay, processed at extremely high temperatures this process causes the raw materials to fuse and form a compact mass with an extremely low water absorption of less than 0.5% resulting in the formation of a very strong body with a flexural strength of 38 N/mm2, solid through color fade proof with a very hard surface Mohs hardness of 7. * The acid resistant tiles come in a range of sizes and thicknesses from ranging from 8-25mm. Our acid proof tiles meet stringent specification norms of IS 4457:2007 and relevant ASTM/DIN standards which ensure excellent performance in Acid/Alkali/Chemical (expect Hydrofluoric acid and its derivatives). Corrosion Protection Applications * Factory Floors subject to corrosion from Chemicals, Acids, Oil & Solvents * Pickling tank and surrounding areas * Food & Beverage Industry flooring * Battery rooms and Control rooms * Demineralization plants * Walls of washing and Paint shop areas * Acid Resistant Tiles Manufacturers India * Our acid proof tiles provide excellent abrasion resistance, anti-skid properties for worker safety and high aesthetic appeal. We also provide specialized corner tiles for reducing chances for acid attack through construction joints. Our standard sizes are 200x100, 200x200 & 300x300 millimeters.

PRODUCT DATA SHEET ACID RESISTANT BRICK Material : RED SHALE Type Acid Resistant Brick Size (mm) 230 (LENGTH) X 115 (WIDTH) X 100,76,65,50,40,38,30,25 (THICK) Specification : ASTM C279, ASTM C410, IS 4860-1982 DESCRIPTION : We offer premium quality acid resistant bricks Red â?? Shale , tiles and special shapes. We also offer customized sizes as per clients' requirements. Our acid bricks comply with ASTM C279 Type-III, ASTM C410 Type H, L, and Indian Standard 4860 - 1982 Class-I for all applications where low absorption and high acid resistance is required. FEATURES OF ACID RESISTANT BRICK: Excellent resistant against wide range of chemicals except hydrofluoric acid, high abrasion resistance, low wearing properties, High Thermal resistant to sudden change in temperature AREA OF APPLICATION: Chemical Analysis (Average) Acid and Alkali Storage Tank Farms Demineralization plants and Water treatment plants Chimney inside lining, FGD linings Towers and Columns Process Vessels and Tanks Sewerage Treatment Plants and Lines Industrial Flooring and Bund Areas Chimney and Flue Gas Linings Hoppers and Chutes SiO266.4 Al2 0324 TiO21.1 Fe2 O31.1 K2 O + Na2 O2.5 NOT RECOMMENDED: HF acid or other fluoride solutions Heavy thermal shock Typical Physical Properties of GANESHAS Acid and Chemical Resistant Brick Characteristic RED SHALE ACID RESISTANT BRICK Test Standard Bulk Density, gm/cc - 2.3 to 2.35 ASTM C-20 -Water Absorption, % - 0.1 to 1.5 IS 4860-1968 Apparent Porosity, % -0.5 to 1.75 S 4860 Acid Solubility (H2SO4), Loss in Mass,% -0.1 to 1.8 ASTM C-279 Modulus of Rupture, PSI -2133 to 3555 ASTM C-67 Compressive Strength, Kg/cm2 - 700-900 IS 4860-1968 Abrasion Resistant , Volume in mm3 -69 to 85 EN 102 Surface Hardness, MOHS Scale - 7

PRODUCT DATA SHEET ACID RESISTANT BRICK Material : FIRECLAY Type Acid Resistant Brick Size (mm) : 230 (LENGTH) X 115 (WIDTH) X 100,76,65,50,40,38,30,25 (THICK) Specification : ASTM C279, ASTM C410, IS 4860-1982 DESCRIPTION : * We offer premium quality acid resistant bricks Red â?? Shale , tiles and special shapes. We also offer customized sizes as per clients' requirements. Our acid bricks comply with ASTM C279 Type-III, ASTM C410 Type H, L, and Indian Standard 4860 - 1982 Class-I for all applications where low absorption and high acid resistance is required. FEATURES OF ACID RESISTANT BRICK: * Excellent resistant against wide range of chemicals except hydrofluoric acid, high abrasion resistance, low wearing properties, High Thermal resistant to sudden change in temperature AREA OF APPLICATION: Chemical Analysis (Average) Acid and Alkali Storage Tank Farms Demineralization plants and Water treatment plants Chimney inside lining, FGD linings Towers and Columns Process Vessels and Tanks Sewerage Treatment Plants and Lines Industrial Flooring and Bund Areas Chimney and Flue Gas Linings Hoppers and Chutes SiO266.4 Al2 0324 TiO21.1 Fe2 O31.1 K2 O + Na2 O2.5 NOT RECOMMENDED: HF acid or other fluoride solutions - Heavy thermal shock Characteristic Fireclay Type Acid Resistant Brick - Test Standard Bulk Density, lbs/ft3 - 2.25 to 2.30 ASTM C-20 Water Absorption, % - 0.1 to 1.8 ASTM C-20 Apparent Porosity, % - 4.05 to 4.14 ASTM C-20 Acid Solubility (H2SO4), Loss in Mass,% - 6.1 to 6.8 ASTM C-279 Modulus of Rupture, Mpa - 14.6 ASTM C-67 Compressive Strength, PSI - 15500 to 17250 ASTM C-67 Abrasion Resistant , Volume in mm3 - 71 to 96 EN 102 Surface Hardness, MOHS Scale - 7 Thermal Conductivity, BTU-in/hr-ft-F - 6.94 to 7.12 ASTM C-236 Thermal Expansion Coefficient,in/in/Fx10-6 - 2.6 to 2.8 EN 103

What is PMMA plastic PMMA resin is also known as acrylic resin, organic glass or glass acrylic. Although not glass, in terms of technical surface, PMMA is quite similar to glass. PMMA is often used in the form of sheets and pieces with good impact resistance, high scratch resistance, and good light exposure. As a good economic alternative to glass, glass, Polycarbonate due to its low cost, it is suitable for projects that require good bearing capacity, difficult to break without high hardness MATERIAL:PMMA plastic repro pellet transparent yellowish CATEGORY: PMMA TYPE: repro pellet GRADE: Transparent Yellowish SPECIFICATION: Repro from film. Color tone is due to UVA additives Origin: Japan LOADING WEIGHT: 24 Ton FOB (USD/Ton): 1450$ - 1700$ Packaging: Jumbo Bag Est. Shipping Time: 15, 30, 45 days

PMMA Sheet Natural Plastic Scrap For Sales MATERIAL : PMMA Sheet Natural CATEGORY : PMMA TYPE : Sheet GRADE : Extrusion SPECIFICATION : All acrylic no contamination ORIGIN : Canada LOADING WEIGHT : 18 Tons CFR (USD/Ton): 700-900

Solid polycarbonate plastic sheet size Width : 1220mm, 1560mm, 1820mm, 2100mm Length : Any length Thickness : 8mm Category : Roofing panels Weight : 1.2kg / mm / m2

Solid polycarbonate plastic sheet size Width: 1220mm, 1560mm, 1820mm, 2100mm Length: Any length Thickness: 6mm Category: Roofing panels Weight: 1.2kg / mm / m2

Acid etched glass is annealed glass treated with acid to give its surface a frosted look. Entire sheets of glass can be acid etched, or small sections can be treated to add specific designs. It make glass artistic, beautiful and long lasting. Normal acid etched glass can be used to create doors, partitions, walls, shelves, and railings, special items can be used as â??anti-glare glassâ?? for picture frame, screen, etc. Product items :� single side acid etched glass / double side acid etched glass Thickness :2-19mm Size :2440x3660mm 2140x3300mm,1830x2440mm,1220x1830mm, any cut sizes

JH acid etched glass is annealed glass treated with acid to give its surface a frosted look.Entire sheets of glass can be acid etched,or small sections can be treated to add specific designs. It make glass artistic ,beautiful and long lasting .Normal acid etched glass can be used to create doors,partitions,walls,shelves,and railings, special items can be used as �?�¢??anti-glare glass�?�¢?? for picture frame , screen ,etc. Product items : single side acid etched glass / double side acid etched glass Thickness :2-19mm Size :2440x3660mm 2140x3300mm,1830x2440mm,1220x1830mm , cut sizes

HIPS Regrind White-Mix Thermoplastic PS has two representatives as GPPS and HIPS resin. In particular, PS HIPS plastic is more popular thanks to many advantages and applications. PS HIPS belongs to the group of hard, transparent resins that are easy to color, machined by suction lamination method and easy injection technology. Common HIPS applications: In packaging technology, it is used as a single-layer packaging for products that do not require strict antioxidant requirements. Make coating HIPS plastic film to increase water vapor and gas resistance. Making a printing surface to increase printing ability, making the outer plastic packaging with the ability to tear easily and create gloss. Making bottle caps, pen cases, jewelry boxes, beer tanks, fresh food containers. Making pharmaceutical bottles, pipes, cap for solvent containers. Making high-frequency insulating materials, insulation clamps. Making imitation leather sandals, textile packaging. Pressing students' tables and chairs, pressed motorcycle details, yogurt cup, plastic candy tray. MATERIAL: HIPS Regrind White-Mix CATEGORY: HIPS TYPE: Regrind White-Mix SPECIFICATION Product- HIPS regrind post production from Yogurt caps Contamination â?? up to 2% foil metalizing (cover of the yogurt caps). Food grade material Post - industrial Sheet Extrusion & Vacuum forming Origin: Spain LOADING WEIGHT: 24 Ton FOB (USD/Ton): 650$ - 850$ Packaging: Jumbo Bag Est. Shipping Time: 15, 30, 45 days

Product Name Hot rolled steel sheet Thickness plate:0.35-200mm strip:1.2-25mm Length 1.2m-12m or according to customer's special request width 610,760,840,900,914,1000,1200,1250mm Tolerance Thickness: +/-0.02mm, Width:+/-2mm Material grade Q195 Q215 Q235 Q345 SS490 SM400 SM490 SPHC SPHD SPHE SPHF SEA1002 SEA1006 SEA1008 SEA1010 S25C S35C S45C 65Mn SPHT1 SPHT2 SPH3 SPH4 QstE Others as your requirement surface iron gray (low carbon plate), brown (special alloy plate, the high carbon plate), partial ochre (weather resistance), with temperature oxidation pattern, than manufacture rough surface

Product Name Carbon steel plate 25crmo4 alloy steel sheet price Thickness 3mm~300mm,2mm-100mm is common thickness,also can customize Width 1000~3000mm,common width is 1250mm,1500mm,2000mm,2200mm Length 1000~12000mm,can as your request cut Surface Clean,finished, blasting and painting or as your request Delivery Hot Rolled, Controlled Rolling,Normalizing,Annealing, Tempering,Quanching, Q+T Packing Steel Strapping,fixing in the Container,can customize

Product Name Carbon steel plate 25crmo4 alloy steel sheet price Thickness 3mm~300mm,2mm-100mm is common thickness,also can customize Width 1000~3000mm,common width is 1250mm,1500mm,2000mm,2200mm Length 1000~12000mm,can as your request cut Surface Clean,finished, blasting and painting or as your request Delivery Hot Rolled, Controlled Rolling,Normalizing,Annealing, Tempering,Quanching, Q+T Packing Steel Strapping,fixing in the Container,can customize

Indonesia origin MANUFACTURER - Solid Wooden Panels Door maker ***** Made from Red Meranti - Mix Meranti or Mix Hardwood *** High density wood *** Could be Standard Door Or White Prime finishing or Painting Sizes and Designed by demand *** MOQ = 350 sheets in 20ft container #### Payment by Bank Transfer Deposit

We are INDONESIA Solid Wooden Panels Doors & Door Frames Manufacturer Made from Vary wood species : Red Meranti - Mahogany - Acacia - Bangkirai ## also can be PRIME WHITE All sizes available by demand Loading 20ft = 400 pcs ***** Price range usd 70 /sheet FOB Indonesia main port for Solid Wooden Panels Door ### Sizes by demand ## We also making 3 layers Solid or Finger Jointed Laminated Door frames or Door Jamb PRICE RANGE FOB Indonesia main port USD 890 /CBM ##### Payment By Deposit Bank transfer or L/C at sight