Painter's tape, also known as masking tape, is a type of pressure-sensitive adhesive tape that is widely used in painting projects. It is designed to be easily applied and removed without leaving residue or damaging the surface it is applied to. Painter's tape is typically made of a Washi paper or Crepe paper as carrier. It has a relatively low-tack adhesive on one side that allows it to adhere to surfaces temporarily.
Wafer Soft Seal Butterfly Valve Size Range: 2 100 DN50-DN2500 Pressure: PN10,PN16 Class150 Body Materials: Ductile Iron/ WCB/CF8/CF8M Disc Materials: Ductile Iron/ WCB/CF8/CF8M Seat Materials: NBR, EPDM,PTFE Connection: Wafer Application fields: Municipal construction, water treatment, water supply and drainage, water conservancy projects, etc.
Hilton Forge India is a leading manufacturer, supplier, and exporter of high-quality flanges in a wide range of materials, sizes, and pressure ratings. Our flanges are manufactured to the highest standards and meet all applicable industry specifications. We are committed to providing our customers with the best service and support. Visit our site to learn more about flanges.
Our longest roller will provide the best coverage and grasp for the back as well as the arms and legs. Simply roll against the muscles to relieve all kinds of stress and tension. The longest roller in this set provides better grip and control, while also reaching further away parts of the body. In addition, the end can also be used to relieve pressure points.
Injection molding machine is also known as injection molding machine or injection machine. It is the thermoplastic plastic or thermosetting plastic using plastic molding mold into plastic products of various shapes of the main molding equipment. It is divided into vertical, horizontal and all-electric. The injection molding machine heats the plastic and applies high pressure to the molten plastic so that it shoots out and fills the mold cavity
SPM Pipe welding pneumatic clamps assure a rapid, accurate alignment of two joints of pipe during the welding operation. Front and rear heads operate independently to lock the clamp into position. A specially designed shoe on each head exerts pressure uniformly around the inside circumference of the pipe to maintain necessary alignment. Each pipe welding pneumatic clamp is easily and quickly adjusted for different pipe wall thicknesses.
Single-acting/double-acting pneumatic actuator. Size standard: NAMUR standard, ISO5211 standard. Cylinder material: die-cast aluminum. It can be equipped with solenoid valve, limit switch and positioner. Air source pressure 2-8 bar. Applicable occasions: indoor or outdoor installation. Available valves: ball valves, butterfly valves, plug valves. Installation method: any position, 360-degree rotation.
Product Name:Purified water storage tank Deionized and Ultra-pure Water Storage Tanks What are some common materials used to make purified water tanks? Purified water tanks can be made from a variety of materials, depending on the intended use and application. Some common materials used to make purified water tanks include: Stainless steel: Stainless steel is a durable and corrosion-resistant material that is commonly used in the food and beverage industry. It is easy to clean and maintain and can withstand high temperatures and pressures.
VIVOLO - XP168 â?? â??SAE AAâ?? TYPE PUMP â?? ø50.8 FLANGE â?? PARALLEL SHAFT Displacements from 0.91 cm3 / revolution to 9.88 cm3/ revolution. Maximum pressures up to 300 bar. Rotation speeds up to 6000 rpm. Configurations with inlet and outlet in the body, flange and cover. Available shafts:
enviClone Photovoltaic PV Module Solar Panel Wind Resistance Dynamic Mechanical Load Test Machine The PV modules Dynamic Mechanical Load (DML) Test Machine simulates the dynamic load with the pneumatic cylinders and suction cups. Each pneumatic cylinder drives one suction cup, and each cylinder rod is equipped with one tension pressure sensor. Each pneumatic cylinder is a separate control module. Periodic load stress test is performed on the Photovoltaic (PV) Modulesâ?? surface, and PV Modules can be installed according to different requirements. The system also has the ability to monitor the curvature of the PV Moduleâ??s center points in real time. SPECIFICATION Model No.: EVCL-DML-2200, EVCL-DML-2600 Max Dimensions of Tested PV Module Panel 2200 mm x 1200 mm, 2600mm x 1300mm, etc. Quantity for each test 1 Piece of PV Module Pressure Method Pneumatic Cylinders Quantity of Pneumatic Cylinders: 50 pcs, 98pcs, etc (varies as per your Max dimensions of solar panel) Quantity of Pressure Sensors: Each pcs for each pneumatic cylinder The Max Pressure can be tested: 12,000 Pa The Max Pulling Force can be tested: 7,500 Pa Accuracy Deviation: â?¤3% Deformation Sensor: 1 (or customized as per requirement) Controlling Method: Siemens PLC + HM1 Drive Method: Air Compressed Load Amplitude Test Range (Static) Pressure:� +500~12,000 Pa (Continuous, adjustable) Suction:� -500 ~ -7,200 Pa (Continuous, adjustable)� Note: The test time and pressures can be adjusted during the test every time. Load Amplitude Test Range (Dynamic) Pressure:� -2,500 Pa ~ +2,500 Pa Suction:� -500 Pa ~ -7,200 Pa Frequency:� 3~7 times / min Accuracy Deviation:� â?¤� �±50 Pa. Test Standards IEC TS 62782 Photovoltaic (PV) modules â?? Cyclic (dynamic) mechanical load testing IEC 61215 Ed.3 Static: Forward Direction 2400 Pa�·1 IEC 61730 MST 34 Equivalent: IEC TS 60904-12, IEC TS 61836, ISO/IEC 17025, etc. Wuxi EnviClone Test Equipment Company specializes in environmental simulation test chambers for various industries such as automotives, photovoltaic (PV) modules, solar power, new energy batteries, rubber manufacturing, electronics, military, etc.
Product Description Technically, the La Marzocco GS/3 is a commercial machine, ready for use in a coffee shop or kiosk but we are also selling it for the home. With dual stainless steel boilers for simultaneous brewing and steaming, a 118 oz water reservoir, separate stainless steel hot water and steam wands, a multifunction backlit keypad and easy to read digital display, programmable water volumes, adjustable temperature control and more, we figured that this machine was too good to hide from a retail audience. If youâ??re ready to blur the line between â??consumerâ?? and â??professional,â?? or if you think the line never really existed in the first place, then youâ??re ready to take a closer look at the respected and reputable La Marzocco GS/3. This machine has a 13 month warranty. Features & Benefits: Coffee Design To the left of the brew group are two pressure gauges â?? the far left pressure gauge shows the pressure in the brew boiler, and the gauge closer to the brew group shows the pressure in the steam boiler. Above these gauges is the steam wand, and below them is the steam activation lever. To the right of the brew group is the digital display with clock and below the display is the keypad. This is also where you find the hot water dispenser and hot water lever. They keypad has icons, so you can remember which button does which. From left to right, they stand for espresso, double espresso, coffee, double coffee, programming and tea. When in programming mode, the espresso and double espresso buttons stand for a down arrow and an up arrow, respectively. The coffee button is used to access certain menus, the double coffee button has no programming function, and the tea button is used to turn the GS/3 on and off. Brewing The machine is heated to proper brewing temperature when the keypad buttons are backlit. Before brewing, itâ??s a good idea to run some hot water through the portafilter. This warms the portafilter to brewing temperature, so your espresso is brewed at a consistent temperature. Add grounds to the portafilter, insert the portafilter into the group head, and press the button corresponding to your preferred drink â?? espresso, double espresso, coffee, or double coffee. The machine will automatically dispense a set volume of water through the grounds. When brewing, the brew boiler pressure gauge should read about 9 bars.
2001J Mainline Packers meet the highest standards for testing and sealing joints of mainline sewer pipes with acrylamide, acrylate or urethane gels. Logiball 2001J Mainline Packers meet the highest standards for testing and sealing joints of mainline sewer pipes with acrylamide, acrylate or urethane gels. A thick, reinforced SBR rubber sleeve is bonded to the stainless-steel core and a layer of softer rubber is applied over the seating portion to provide superior seating against rough surfaces. The smooth outer finish reduces the adherence of the grout on the packer. Logiball 2001J Mainline Packers come with two grout ports and a third port dedicated for the test medium (air or water). MAIN FEATURES: Void Pressure Monitoring Systems: Two different void pressure monitoring systems are available to accurately transmit the void test and grouting pressures to a gauge read by the camera or through a pressure transducer. The conventional localized sensor is recommended for acrylamide and acrylate grouts. The in-wall water chamber sensor is recommended for stickier grouts such as urethane gels and polyurethanes. The 2001J Packer can be ordered with both systems or one of the two as needed by customer. Dedicated Test Port: By using a dedicated hose from the truck to the packer for the test medium (air/water), â??Hâ?? blocks are eliminated and the mixing ratio of the two-part grout is kept constant (no flushing of the catalyst when testing). Features Three-Function Adjustable Rubber Check-Valve: They provide added safety against syphoning the tanks and unwanted backflow contamination into the hoses, and provide a good mixing of the two-part chemicals through the fan like stream of the opposed and adjacent ports. The Autotesting Concept: When inflating the 2001J packers, the ends first seal against the pipe wall, while its central portion progressively expands, trapping air and water, and compressing it into the mixing chamber. The pressure in the chamber is transmitted through the improved liquid filled sensor and/or the in-wall water chamber sensor to a gauge or transducer installed on the packer. The operator can tell if a joint is obviously good or not by simply inflating the packer over it. By avoiding time consuming conventional tests, productivity could be increased by as much as 30%. Logiball 2001J Packers approximate void volumes. ICGA promotes the proper use of chemical grouting as a safe, economical and effective mean to reduce ground water.
Venus Legacy Body Shape slimming device fat removal Radio frequency Skin Tightening Machine. Model: iShape III+ 2024 upgraded best equipo cellulite SPRT v10 sculptor body slim shape machine weight loss for sale 1.Skin Tightening 2. Wrinkle Removal 3. Eyes' area treatments 4. lncrease skin elasticity 5. Fat and cellulite reduction 6. Face wrinkle removal & lifting 7. Warm vacuum cellulite massage 8. Body slimming, contouring & shaping 9. Promote cell metabolism, improveblood circulation 940nm Infrared laser reduces skin impedance by heating skin and RF energy penetrates deeply into connective tissue; The synergistic combination of infrared laser and conducted Bipolar RF energies increase the oxygen intracellular diffusion by heating the skin Vacuum plus specially designed rollers manipulate leads RF penetration to be even 5-15mm. At the same time, Cavitation and Rollers mechanical tissue manipulation nips and stretches fibrillar connective tissue, effectively breaks down subcutaneous fat as well as extruded capillary vessel, Increase lymphatic drainage, promotes metabolism and reduces or shrinks the size of the actual fat chamber and greatly improved body contouring effect; The technology that vacuum folds skin makes RF energy penetrate a specific folded skin, greatly improve effect and safety, even for the upper eyelid area treatment. Technology 1: Cavitation 40KHz Cavitation technology in itself means that the ultrasound causes the fat cells to vibrate so fast (high frequency) so vacuum bubbles are formed in the cell. As a consequence, the outer casing of the fat cells (the membrane) is "blown out" and the fat ends outside the cells. Outside of the membrane, the fat can be broken down to rapidly accessible energy, which is then taken up in the blood or transported by lymph nodes, after which they are either burned or stored in other fat cells elsewhere in the body. Technology 2: Mechanical roller massage The mechanical roller massage works profoundly on densified connective tissues. The mechanical massage rollers enhance the skin's cell-generating activity, resulting in thickened fat deposits being drained. Technology 3: Vacuum massage The vacuum massages lift, mold and massage the skin deep and on the surface. The massage also increases the blood circulation, which in turn leads to the release of fat from the fat cells. The massage further provides a tightening of the skin. Technology 4: Bipolar RF(radio frequency) Bipolar RF makes water molecules in the fat revolve with high speed to produce friction and shock, then triglyceride go out from fat. RF energy with 1-10M could get to 4-15mm skin depth, which makes every layer get heat evenly. The new collagen makes skin turn tighten. This Bipolar RF makes the reorganizing fat cells connect more closely, stimulate the collagen re-grow, avoiding flabby skin after slimming treatment. Technology 5: 980nm infrared light
Foot Massage Ball, Spiky Mini Massage Ball, Deep Tissue Massage Ball For Sale Spiky Massage Ball System Parameters: Product Name Bulk Small Pilates Spiky Mini Deep Tissue Massage Ball for Back Pain Exercises Material: PVC Color: Custom Color Size: 5/6/7/8/9/10cm or Custom Size Logo: Custom Logo MOQ: 500pcs Delivery time: (1)7-10 working days-for existing products (2)10-15 working days-if need customized logo OEM Service: Yes Certification Available: Yes Packing details: Poly Bag+Carton Production Capacity: 200000 Piece/Pieces per Month Payment Term: L/C,T/T,D/P,PAYPAL,Trade assurance Spiky Massage Ball Description: Imagine yourself feeling totally relaxed, pain and stress free after a long hard day. SAVE YOUR PRECIOUS TIME AND MONEY and HAVE AN INSTANT PAIN AND STRESS SOLUTION available anytime and anywhere! Afford it quickly with our Massage ball foot rollers. You will love and enjoy the Best massage therapy with our physical therapy Balls! Wouldn't you love to easily RECOVER YOUR PLANTAR FASCIITIS, IMPROVE REFLEXOLOGY and eliminate those stubborn Headaches or Backaches without taking pills? Due to high quality and pvc material our compact stress ball with strong spikes will provide you the deepest body and tissue massage effect with the softest touch with your skin. Ease your tight muscles with our trigger point massage roller ball.You can use our massage roller for massaging the feet or hands before, during or after physical activity for tight muscles and cramping in conjunction with rehabilitation to complement physiotherapy treatment. When the balls need cleaning simply soak them in soap water for a few minutes, thoroughly rinse and air dry. It is also known by various names, including massage ball, yoga massage ball, foot massage ball, hand massage ball, spiky massage ball, deep tissue massage ball and therapy ball. It can also be used inphysical therapy and athletic training, with below functions: 1. Experience a full body and muscle relief 2. Enhance body awareness 3. Correct bad posture 4. Reduce joint stiffness 5. Improve flexibility both in individual muscles and large muscle groups 6. Increase blood flow to local areas, which in turn can improve blood circulation 7. Spiky Balls are used to soften the muscle and help to relieve muscle tension in specific areas of the body which is causing niggling pains. They can also release the Fascia especially in the foot. Bingehua specializes in the production and export of fitness accessories, body-sculpting and power training goods, mainly including yoga ball, Resistance Band Loop, Half Balance Ball, etc. Our own factory was founded more than 10 years.
Stainless steel water tank SUS316,SUS304 can be choosen depending on the water quality and usage environment ,stainless steel boards are shaped by hydraulic press mold, the standard specification is 1000x1000mm or 1000 x 500mm, they are welded on site by arc-argon welding machine,the welding surface is washed and passivated by acid to ensure the welding parts will not get rusted. Factory use unique stainless steel plate and the high difficulty ramming formation craft to achieve the high strength requirenments with the smallest material consumption. The weight only be third of the ordinaly panel. 1.The raw materaial plate was anlysised by our material anlysier to assure the quality 2.The welding is argon arc weld(TIG) to avoid plate's oxidized 3.After welding the the inner tank ,we will make a full water pressure test to check the welding joint .After welding the jacket ,the full water pressure test be done for jacket too 4.After finishing the surface finish ,our people will make a surface roughness testing to assure the Ra data . 5.After agitator installment ,we will operate it to assure the function is good . 6.The nozzle's position 's confirm also is checked by our quality control people .
Senwart water pumps are equipped with an oil level alarm system: when the oil level is too low, the gasoline engine will automatically stop running to avoid specific damage to the engine. Aluminum alloy and durable cast iron body can withstand high pressure and is more durable, with simple and reliable structure to maximize flow rate. Wear-resistant graphite and ceramic magnetic mechanical seals are used to provide excellent sealing performance. High-pressure pump with wear-resistant cast iron volute and aluminum alloy impeller to maximize flow. MODEL: WP30G Engine type : 168F-1 Engine : 4 Stroke, single cylinder, air-cooled Displacement : 196cc Motor type : Gasoline Engine : 3,600rpm Power : 4.8kW / 6.5HP Outlet size : 3 inch / 80mm Inlet size : 3 inch / 80mm Max flow : 60m�³/h Total head : 30m Suction : 8m Fuel tank : 3600ml Compression ratio : 8:05:01 Start model : Recoil Oil tank : 600ml Package : 505x410x450mm N.W./G.W. : 31kg/35kg Qty.:20'/40'HQ : 300pcs/600pcs
BJ-PA is a macroporous weak base anion exchange resin with styrene-DVB matrix, having primary amine groups. It has high regeneration efficiency with low amount of regenerant and yields high operating capacities. Large organic molecules are also readily removed by the resin and easily eluted due to macroporous structure of BJ-PA. It is supplied in free base form. FEATURES & BENEFITS Uniform particle size 95% all beads are in the assignation range; giving a lower pressure drop and superior kinetics. �?�¢??Organic fouling resistance BJ-PA primary amine functionality and its macroporous structure provides nearly 100% regeneration efficiency and the ability to reversibly sorb naturally occurring organic substances. �?�¢??Superior physical stability High sphericity combined with high crush strengths and uniform particle size provide greater resistance to bead breakage resulting in longer service life and lower pressure drop. PRANCIPAL APPLICATIONS BJ-PA has high chemical stress and physical stability. These characteristics, in addition to the large pore size, allow BJ-PA to be specially used in acid removal, color removal or carbon dioxide.
Size:600*600mm Resflor Introduction of Products  Full steel, tile could be HPL or PVC/ceramics. Lower plane is ST14 stretched plate, surface plane is SPCC hard steel both are Shanghai Bao steel. Foaming cement infillled conductive regula for four sides. Pedestal is pressured forming by steel plate, lead screw can be adjusted at discretion, stringer is made with square tube. Characteristics     1.Prevent static validly; flame retardant, dustproof, antiskid, antirust, antisoil ,  esistance to chemical attack.     2.Environmental adhesive, strong wearability, non-bubble non-degumming; painted steel body to prevent static, soft light, wearproof, artistic.     3.Super strength loading, pressurization.     4.Fix conveniently, assembly agility, bottom space could be used for air conditioning.
Constant-fluron PTFE particle resin G401 is a free-flowing white powder composed of relatively large particles that is ideal for isobaric molding. Its most unique features are improved moldability at lower pressures and improved surface smoothness of finished parts. PTFE G401 is often used to form thicker sheets, and sometimes for the stamping of rods and pipes with thicker cross sections. Properly processed products made from high purity PTFE G401 have the superior properties typical of fluoroplastic resins Processing suggestion Fluoron PTFE is processed in two steps: preforming and sintering. The powder is first pressed into a preformed shape close to the desired molded product and then consolidated at temperatures higher than the melting point of the pure powder crystal using precise heating (sintering) and cooling cycles. The performance of the finished product depends on the bottle failure pressure, sintering time and temperature, and cooling rate. PTFE is used to make relatively large objects in molds that can be manually filled. Small particles of resin do not flow properly in the automatic feeding system.
Product Application: Ceramic salt cores are primarily used in the casting process of liquid forging aluminum alloy pistons. By forming cavities inside the piston, ceramic salt cores help achieve an internal cooling structure for the piston. Features: High Strength: By adding ceramic additives, ceramic salt cores achieve high strength, enhancing their ability to withstand high temperatures and pressures of aluminum liquid. High Density: Multiple granulation techniques are employed to achieve high density in ceramic salt cores, contributing to the overall quality of the castings. Low Linear Expansion Coefficient: Through innovative sintering techniques, ceramic salt cores achieve a low linear expansion coefficient, reducing the impact of thermal expansion on aluminum alloy pistons. Ceramic salt cores are typically used in the casting of liquid forging aluminum alloy pistons. Compared to traditional salt cores, ceramic salt cores meet the requirements of high-pressure casting processes for salt cores by increasing ceramic additives, using multiple granulation techniques, and innovative sintering techniques to achieve high strength, high density, and low linear expansion coefficient performance.
