The princple of the machine: It is based on the proportion of grain crop and cobble density differences, by adjust the pressure and vibration frequency separate the stone and grain. The machine is equipped with a multi blade fan with high accuracy, the lighter grain crops will be suspended state, and the larger proportion of the stones will cling to the stainless steel mesh by adjusting the air pressure, and then by adjusting the frequency that stoner table vibrates so as to achieve the purpose of separation. The machine equipped with frequency conversion control device can be subtle regulation, even if the proportion of the difference is very small, stones also will be separated. We are the cream separator chinese supplier.
RMT 1210 SVR model comes with "silencer" and "Vibration Reduced" Handle. With its new back head design and new muffler, the RMT 1210 SVR combines excellent performance in its weight class with good ergonomics. Lowering the vibration levels offers immense benefits to the operator. They do not tire easily so it increases their productivity. Reduced vibration levels also control its negative effects on operators. It is an upgraded version of RMT 1210. Model # RMT 1210 SVR Weight with silencer 24.5 kg 55 lb Length 600 mm 24" Air pressure 6 bar 87 psi Air consumption 26.5 l/s 56 cfm Blows per minute 1400 Air inlet 19 mm 3/4" Shank size (standard) - 8900 0030 06 25 x 108 mm 1" x 4�¼â?? Shank size (option 1) - 8900 0030 08 28 x 160 mm 1�¹â??8â?³ x 6�¼â?? Shank size (option 2) - 8900 0030 10 32 x 160 mm 1�¼â?? x 6�¼â?? Retainer type Latch
An Stainless Steel Air Shower is a highly versatile local purification device in which clean, filtered, strong air is blown out of the surface of the person entering the clean area by the fan through the air shower nozzles to remove the adsorbed dust. What does an air shower room do? In a clean area, the source of bacteria and dust is the operator in a dynamic situation. Before the operator enters the clean area, the dust particles adhering to the surface of his clothes must be blown with clean air and act as an airlock. The Stainless Steel Air Shower is the purification equipment for personnel to enter the clean zone clean workshop, it is universal and can be used with all clean zones and clean plants. When entering the workshop, the staff must pass through this equipment, with strong clean air, by rotating nozzles from all directions to spray to the person, effective and rapid cleaning on the clothes attached to the dust, hair, hair dander and other debris, it can reduce the problem of pollution caused by people entering and leaving the clean area. How many types of air showers are there? Air shower rooms can be divided according to the blowing mode into. (1) Single blowing type: a side panel with nozzles, suitable for factories with low requirements, such as: food packaging or beverage processing, production of vats of water, etc. (2) Double blowing type: one side plate and the top plate have nozzles, suitable for domestic food processing enterprises, such as: pastry making, dried fruit and other small-scale enterprises. (3) Triple blow type: two side panels and the top have nozzles, suitable for export processing enterprises, or high precision instruments and other demanding industries. The importance of clean room air showers When a clean airflow is sent into the room from the air supply, it will quickly spread and mix, and at the same time the airflow is discharged from the air return, using the clean air supply airflow mixing dilution effect, the original dust concentration of high indoor air dilution, while indoor pollution sources generated by the uniform diffusion of pollutants can also be discharged outdoors in a timely manner, to achieve the corresponding dynamic balance, to meet the requirements of indoor cleanliness, to achieve the air supply The key to achieving a better mixing and dilution of airflow is to make the indoor airflow diffusion speed fast and uniform airflow.
D Atomizing Nozzle has special interior structure, which can evenly mix liquid $ gas and generate tiny spraying drop or large spraying drop. In common situation, we can get super tiny (about 30 um) liquid spraying drop by air pressure increasing or hydraulic pressure decreasing. Adjustable Atomized can adjust liquid capacity. It can meet the requirement of spraying without changing air pressure and hydraulic pressure. Therefore, it has good adaptability. Each spray device is composed of air cap and liquid cap, which can offer two spray modes, flat fan and round, with wide liquid capacity coverage. Various available sizes of inlet joint for spray nozzle, it is flexible with changeable parts. Atomizing Nozzle has good moisture effect. It is the ideal choice for the location where requires moisture control. Common Application: 1.Wool Spraying & Moisturization 2.Mould Lubricating 3.Spraying Injection 4.Air Disinfection
Detailed product description Ats fpd-4fan hanging ionizing air blower Is a kind of static eliminator, that can provide a balanced ion flow and eliminate static or neutralize static in large-scale concentrated area or eliminate the static in those area that not easy to contact. The shell adopt stainless steel material, the ion flow is concentrated, the cover area near to zero gap, have good effective to eliminate static. Ats fpd-4fan hanging ionizing air blower working principle: Ats fpd-4fan hanging ionizer air blower can produce a lot of air with positive and negative ion, the electric charges on the object and fall, when the object surface charge negative static, it will attract positive ion in the air, when the object surface charge positive static, it will attract negative ion in the air, so that the electrostatic on the surface of the object is eliminated. Product features: *suitable for large-scale to eliminate static electricity; * quick static elimination, convenient installation; *with cleaner of ion emitter *build-in fan and high voltage generator; * ion wind volumn is ajustable Ats fpd-4fan hanging ionizing air blower applications: Precision electronic products; electronic assembly line, the production of microelectronics, optoelectronics; pharmaceutical manufacturing assembly lines, printing, packaging; small part injection molding, shear plastic film, circle and film, as well as mold release etc.. Specification: Operating voltage: 110v/60hzor220v/50hz Current consumption: 1ï25aor0.62a Operating temperature: 0---50 Size: 1100mm(l)*184mm(w)*110mm(h) Weight: 7kg Air volume: 120---330cfm Offset voltage: 0vâ±10v Air coverage: 40cm*120cm Test results:testing conditions Testing voltage:1kv to 100v operating voltage:110/220v temperature:22
Half Automatic Flat T bar roll forming machine is the machine to make ceiling T bar by roll forming principle. Half automatic machine means that you need to punch the holes and ends of the flat T bar. Same as other T bar, flat t bar also has main T and cross T two types. Normally the T bar sizes 32x24x3600mm; 38x24x3600mm 38x35x3600mm; 32x15x3600mm etc. Simple and brief introduction of half automatic T bar roll forming machine: NO.ItemBrief introduction 1Frame tableMaterial: Carbon Steel, Thickness: 20mm, Polished, Anti-rusting processing 2RollerMaterial Cr12 Inner diameter 40mm, Min OD 90mm, Hardness HRC 55-56, Symmetry in the range of 0.05mm, 16 roller stations 3TransmissionChain Drive or Gear 4StitchFour Rollers real stitch can also be used for fake stitch. 5Side PlateThickness 30mm, Polish 6 sides, high precision boring 6Principal axis45# steel, tempering heat treatment, mill grinder precise making 7Electronic control systemPLC programmed, Touch Screen, full automatic controlling system. 8Stamping MouldsMaterial D2, Hardness HRC 58-60, Precise milled, precise making, easy to removable parts. Advantages of Zhongtuo Half Automatic Flat T bar roll forming machine: Full automatic production to make the T gird shape. For the finished ending making and punching hole, needs another punching machine. Machine working speed is around 25meter per minutes and speed is adjustable. Hydraulic punching for anti slip holes and the company logo if you need. Hydraulic shearing and servo flying system. The product punching die and cutting off blade, we use SKD11 as material, long time to use. PLC control system, Human-Machine interface, portable and touch screen. The brand of PLC is Panasonic.
Geyser, water purifier, air cooler , ceiling fan.
Product model : DR-01F Material: Aluminium alloy with anodized surface Nozzle Material: Imported stainless steel 316L Size: W330*D330*H180mm Rated voltage: 220V/50HZ Power: 50W Volume: 25db Oil consumption: 3ml / h N.W: 8KG Capacity: 500ml Coverage: â?¦3000m3 Certification&Assurance: CE,RoHs,FCC Mist Method: Patent atomization technology Payment: 100% in advanced payment for the first order; Advance of 30% by T/T and shipment after receipt of balance for the next order. - Product Advantages: 1. Microcomputer automatic control, enjoy fragrance service at any time, flavor concentration adjustable. 2. Using the principle of two-fluid atomization,the scent and essential oil are completely mixed inside the nozzle to form a nano-level atomization state. 3. Imported air pump, with 24-hour continuous operation and more than 15000 hours of service life, producing low noise. 4. Equipped with a built in fan which largely expands the range of aroma - Connect to central air conditioning 1. First check if all the equipments are complete,then take out the atomizer connector at the atomization outlet,replace the quick connector to connect the external mounting tube and charge,then turn on the power. 2. Turn off the fan switch for program setting,add essential oil,connect the mounting tube to the air outlet of the central air supply system and secure the device. (Note: For the first time, you need to power off and install essential oil equipment before setting up the program.) - How to maintain Maintenance: If the equipment does not necessary to operate for a long time,it needs to be cleaned with 95% industrial alcohol for the internal nozzles and other accessories.
1. Raw materials: (for step 1) A. Pulp Board Different pulp made by bulrush, straw, bagasse, bamboo, wood etc. B. Waste Paper Such as paper board, carton, newspaper, magazine, waste pulp. C. Plant Fiber Palm fiber, straw fiber, sugarcane fiber etc. 2. Configures: For step 1: Hydrapulper, Pulp Pump, For step 2: Air Compressor, Agitator, Self Priming Pump, Pulping Machine. Egg tray Forming Machine, Vacuum Pump, High Pressure Washer, Pressure Tank, Mould, Transfer Mould, Baler,Low Vacuum Filling Machine. For step 3: Induced Draft Fan, Conveyor, Fan, Mesh Bag Actuator, Dry Iron Roller, Mesh Belt Slide, Mesh Belt Bag. 3. Drying methods: (you can choose the best one which fits your order) 1.Single Brick Drying Line. 2.Single Metal Drying Line. 3.Multi Metal Drying Line.
Laminar Flow Hood Clean Bench is a piece of box-style air purification equipment that offers a class 100 (ISO class 5) aseptic working environment that is mostly dust-free and clean for local use. The Laminar Flow Hood Clean Bench is designed to meet the cleanliness requirements for local working areas in various fields such as modern industry, the photovoltaic industry, biopharmaceuticals and research and testing. Working principle The principle of the clean air laminar flow cabinet is that the air is sucked in from the natural environment by a centrifugal fan and passed through a piece of foam-like patio cotton called a "medium efficiency filter", which filters out the large particles of floating dust; the remaining small particles over 0.3�¼m are then filtered out according to a HEPA filter called a "high efficiency air outlet". According to the double-layer filtration, the air entering the clean bench cavity is clean to a class 100 standard, and the clean bench is clean in addition to ensuring sterility testing. Categorization According to its cyclonic orientation, it can be divided into horizontal single-sided flow clean benches and vertical single-sided flow clean benches. Horizontal Single-Sided Flow Clean Bench The filtered clean air is blown immediately to the operator from the back to the front, it is a very practical clean bench. It is commonly used in the field of electronics, defence and security, instrumentation, dashboards, pharmaceutical industry, etc. Vertical Single Side Flow Clean Bench Vertical flow means that the filtered clean air is blown from the top down onto the clean bench top and subsequently blown backwards and forwards out of the clean bench. Vertical flow clean benches are generally used in the laboratory, biomedical, optical industry chain, microelectronics, computer hard disk manufacturing and other industries. Applications The laminar flow clean bench is one of the basic equipment often used in various laboratories, especially in biotechnology research experiments, this equipment is essential. It is also widely used in various industries such as medical and health care, biochemistry, biopharmaceuticals, environmental monitoring and electronic instrumentation, where it can be used with good performance and a high level of safety.
Closed Circuit Cooling Tower Closed circuit cooling tower (also known as an evaporative air cooler or closed cooling tower) is the tubular heat exchanger placed in the tower, through the circulation of air, spray water and circulating water heat exchange to ensure the cooling effect. AUVC not only provides different shapes of cooling towers used in industries, such as round shape cooling towers and square cooling towers, but also offers closed cooling towers and open circuit cooling towers as well. The type of closed circuit cooling tower is widely used in iron and steel metallurgy, power electronics, machining, air conditioning system and other industries. How do closed circuit cooling towers work? Closed-circuit cooling towers make it possible to separate the evaporative circuit from the process circuit (customer circuit). A stainless-steel plate heat exchanger attached to the cooling tower, in its dedicated room, allows a glycol-free operation, and a simplified and unequalled ease of maintenance. The closed circuit cooling tower works as follows On the process side to be cooled (customer loop), the water to be cooled enters a plate heat exchanger connected to the tower and is cooled and discharged. The primary loop is closed and never comes into contact with air. On the secondary side of the cooling tower, the water is sucked out of the pool by a pump and circulated through a stainless steel plate heat exchanger. The water leaving the exchanger is piped to the top of the unit. This water is graded and evenly dispersed over the exchange surfaces by dispersers (also known as water distribution nozzles). Air driven by fans (axial or centrifugal) enters from the lower part of the cooling tower, is heated and saturated with water and exits from the upper part, passing between the exchange surfaces. Under the effect of the surface tension of the filler ladder, the water spreads uniformly and flows away over the entire height of the tower. The exchange surface is thus increased. The water cooled by forced ventilation falls freely into an inclined pool located at the bottom of the unit. Three reasons to choose a closed cooling tower No contamination in the primary circuit. Many civil and industrial processes require that process fluids be kept free from external environmental contamination: this is true, for example, of most food production processes. Closed-circuit cooling towers fulfil this need: in effect, the coils separate the process fluid from the ambient air drawn in by the fan, keeping it clean and contamination-free in a closed loop.
A clean booth is a type of air purification equipment that provides a localised high clean environment. Clean boothes are available in a wide range of cleanliness levels and space configurations. They are easy to use, flexible, easy to install, short construction period and removable, and can be added to general class cleanrooms where high cleanliness is required to reduce costs. Products Components The clean booth is mainly composed of a box, fan, primary air filter, damping layer and lamps, etc. The shell is sprayed with plastic. The product can be both suspended and ground supported, with a compact structure and easy to use. It can be used as a single unit or connected in a number of ways to form a ribbon clean area. The clean room is made of industrial aluminium (or stainless steel square, iron square with plastic spraying) as the frame, the fan filter unit (FFU) feeds the air and the anti-static drape (or toughened glass) is hung around, its internal purification level can reach 100-10000 levels. Advantages 1.The clean room can be applied independently or composed. 2. Compared with the civil engineering or assembly type building class 100 clean room, the project investment is low, the effect is good, the installation is simple and the operation cost is low. 3. Modular design structure, upgrade clean room level is very easy, scalable, and repeated use of high value. 4. Easy to move around for cleaning (universal castors can be installed). Application areas 1, Electronic factory. The workshop of an electronic factory typically has low outside purification levels, so the interior will need high-level clean areas, such as assembly line work areas, inspection tables, and special equipment work areas that release dust particles or special gases. 2, Food factory. In the food production process, it is generally recommended to use a 100-level clean shed for the packaging process. The higher the level, the higher the safety compliance rate of the food produced. 3, Laboratory: Controlling the experimental work in the clean shed area can improve the success rate of scientific research projects.
Latest IG line (Double glass production line) Main Features: Adopt Siemens and Omron control system, keep stable performance PLC control system, touch screen interface Coating&LOW-E glass automatic identification Intelligent batch-type energy saving system Digital display the depth of glue, automatic adjustment device Servo control stepped glass system, modularity function, superposition function Stepped IG, Triple IG , shaped IG automatic assembly Seven parts23.5meters Glass washing part: 1.Washer with the design of upper and lower washing sections 2.Fan with variable frequency fan, energy efficient, better cleaning effect 3.The air knife can automatically adjust the width of the air knife according to the thickness 4.Hierarchical type washing system 5.Water tank automatic temperature control, water replenishing system 6.European silencer system&stainless steel drying system Pressing part: 1.Ultra-long insulating glass can be compressed in the second time 2.The machine adopts servo torque compression 3.The pressure plate with adjustable flat and no deformation, can guarantee long-lasting high-precision tablet 4.Equipped with a precisely adjustable front platen mechanism 5.The system can diagnose fault information 6.The press plate can be opened to 65mm width for easy maintenance Gas filling part 1.Automatically filling air within the plate, synchronous compressing glasses, to maximize the gas retention rate 2.When filling shaped IG, inflatable front side of the rectangular size required 450mm (length), 280mm (high) 3.No need to drill holes in spacer frame 4.Standard filling gas is Argon 5.Fast reacting sensor for permanent control of gas filling process Clip For Kitchen
QP series tractor (QLN-1504) are specialized products with excellent quality. Its user-friendly design and strictly inspection and manufacturing process will bring you comfortable driving experience. 6-cylinders turbocharge engine with strong power, high fuel efficiency, and high torque output; Hydraulic driving brake system and handle-manipulated stop braking system, high safety coefficientï¼? Luk(Germany) independent-operation, dual-action clutch with reliable performance, large torque reserve coefficient, and high transmission capacityï¼? New-generation graceful and splendid streamline casing, meeting requirements for safety,dust-proof, noise reduction, and heat dissipation. Enclosed cab with heater, fan, air conditioner, and the sounding system is optional, which makes driving safer and more comfortable.
Working principle: the powder center will transfer the powder from the hose to the spray gun and be sprayed onto the workpiece by electrostatic spraying in the air. The two - dimensional elevator controls the upper and lower parts of the spray gun to complete the powder spraying more efficiently. 30 to 40% of the powder in the spray chamber is ejected by the spray gun and is adsorbed on the surface of the workpiece surface for surface treatment under the action of static electricity. The remaining 60-70% fall into the lower grooves and are sucked into the wind by the fan and sent back through the hose to the powder center for reuse. A small fraction of the powder is absorbed by the powder recovery equipment and the ordinary powder falls into the powder keg and uses it to complete the secondary recovery. Tiny particles can be expelled in the wind.
Our industrial ultrasonic humidifier uses a ceramic diaphragm vibrating at an ultrasonic frequency to create water droplets that silently exit the humidifier in the form of cool fog. Usually the mist gets forced out by fans. Ultrasonic humidifiers use a piezoelectric transducer to create a high frequency mechanical oscillation in a film of water. This forms an extremely fine mist of droplets about one to five micron in diameter, that is quickly evaporated into the air flow, thus relative humidification increased. The whole process do not need any physical or chemical heating We are always trying our best to offer our buyers good products with a cheap price, thank you for choosing our products. Please note: Only 220V is available now. We ship world wide, specific shipping fee, please contact me.UltrasonicHumidifier
Stainless Steel Welded Wire Mesh Stainless Steel Welded Wire Mesh, it is a grid that consists perpendicular wire strands, which are welded at each intersection, the joining of the wires at the intersection is achieved by electric resistance welding. According to the welded mesh and wire diameter, it can made into stainless steel welded mesh rolls and welded mesh panels. Materials: SS201, SS202, SS302, SS304, SS304L, SS316, SS316 and so on. Wire diameter: from 0.6 mm to 2.6 mm. Mesh opening: mini 6.4 mm and max 200 mm is available. Application of stainless steel welded wire mesh In houses, stainless steel welded wire mesh is often used as room dividers, ceilings, wall cladding, vents and soffit screens. Reinforce the building with infill panels in the building, create a ventilated attic with soffit screens, and a heating space with radiator grilles. In agriculture, it is used for trees of various shapes and sizes, yards, pastures, greenhouse benches, and corn storage spaces, and it is also used as a farming shelf for tractors. Used as animal enclosures and birdhouses in animal breeding, such as captive goats, horses, cattle, chickens, ducks, geese, rabbits, pigeons, etc., to protect small animals and poultry. In terms of traffic, it is used not only as a fence for expressways, but also as a protective net for road green belts. In the production, it is used as a rope net outdoor paving for a logistics warehouse, a merchandise display rack, a shelf and a storage rack in a grocery store. In our daily life, it is used as window cut fender, food basket, shopping cart, deck or network fence, garden and house fence. For birds, stainless steel welded wire mesh is the only way to prevent zinc poisoning in birds. Its sturdy structure and thick cables also make it the best choice for zoo fences. Other more applications: metal racks for drying food, spark suppressors on top of chimneys, guards for railings, industrial fans and machines, safety fences for other protected electrical appliances, etc.
ZB6302-5 Size: Wire Diameter: 6mm.More parameter details please see the picture. * Wire Drawing Treatment: The surface is processed with wire drawing treatment. High gloss and touch smoothly. High polished surface. Smooth surface without burrs. Durable 316/304 Stainless Steel: We use solid 316/304 stainless steel. Compared with common stainless steel, it s more wear-resistant, anti-rust and corrosion-resistant. This material is perfect for long time outdoor work. Solid stainless steel structure provides higher strength. Full welding, strong solder joints. Not easy to break, loosening and shedding. Widely Use: It can be used with various kinds of buckles, quick links and links. Mainly used in boat bolt, roof beam, ceiling fan hook and wood. Great for Suspension Training Straps, Gymnastic Rings, Yoga Swings Hammocks, Boat & Marine Deck Hardware. Our company possesses the advantaged position on the verge of . And we have convenient transportation extend in meanly engaged in the metal products. Our business is a system includes the designing, production, machining and selling. Our products are camlock coupling, rigging hardware, marine hardware, auto accessories ,as well as the machine parts .According to the standards of API ANSI BS DIN JIS, the products are made to pretty , rational construction, superior performance. The material of our products is kinds of stainless steel ,such as 304\316\316L ;aluminum; brass; pp; nylon and carbon steel. The products are used in many area covering the marine transport, petrochemical industry, Pharmaceutical papermaking, food industry ,electricity industry and so on
Zhongtuo automatic high speed interchangeable ceiling t grid roll forming machine could be used to make Main T and cross T. Main T: equiped with inverter motor, producing in line speed: 30M per minute. Hydraulic automatic punching and cutting machine linked with main forming machine,punching and cutting automatically. Two heads and middle holes are punched and cut-off at the same time after forming. Cross T: equiped with both inverter and servo motor producing in line speed: 30M per minute. Main machine with constant speed,it is traced by the servo trace system, automatic tracing the speed of the main machine, punching and cutting automatically. Two heads and middle hole are punched and cut-off at the same time after forming. some technical parameters of ceiling t grid roll forming machine Decoiler Usage: It is used to support the steel coil and uncoil it in a turntable way. Passive uncoil pulled by roll forming system Loading capacity: 3T Uncoiling width: 500mm Inner diameter: 450-550mm Main roll forming machine: Feeding and flatting will make sure the steel is neat clean and straight. Roller fixer : Guide column Frame : middle plate welded Memorial arch frame type Drive mode: gear Diameter of shafts: Ï?40mm Shearing machine: Power supply : hydraulic power Frame : Pillar style with rack & pinion system Stroke switch : non-contact photoelectric switch Electic Control System: 1. Adopted PLC, transducer, touch panel from Delta Taiwan to ensure high speed with stability, precision and lifetime. 2.Other electric element are Delta 3. Equipped with movable switch, air break, radiator, transformer & electric leakage protector for operation convenience and safety. This kind of T grid roll forming machine is fully automatic. It can do punching and cutting automaticly. The final products can be packed directly.
Mini-pleated panel HEPA filter is a kind of filters adopts equidistance and flow-friendly design of the pleats, as well as uniform media velocity and a very minimal pressure drop. This implies a very reliable and cost-effective operation along with a quasilaminar outflow. Mini-pleated panel HEPA filter is a type of HEPA filter intended to remove the smallest particles. The filter employs a unique medium designed to absorb both small and large particles while limiting airflow as little as possible. The MINI PLEAT structure is intended to increase the surface area of the filter. In comparison to conventional pleated filters, this filter has an average surface area that is over 5 times larger. Longer filter life and greater filtering capabilities result from the increased surface area. Characteristics Filter media are high-performance micro-glass-fiber papers. Filter Classes E10-H14. Cast airtight joint connecting filter media to frame. High durability, resistance to organic compounds. High efficiency, low resistance, simple installation, superior sealing, compact structure, and cheap running costs. Applications Sophisticated air-conditioning Hospitals' operating rooms and intensive care units, pharmacies, sterile rooms, labs, research facilities, etc. Sensitive industrial processes Microelectronics, pharmaceuticals, biotechnology, chemicals, optics, and food and beverages Outlets and modules in the ceiling for adaptable cleanroom systems.
