Brighto Acrylic Primer (Exterior/Interior) Price : 0.90 Ltr - USD 2.6 3.60 Ltr -USD 4.6 18 Ltr- USD 19.2
Brighto Texture Primer (Exterior/Interior) Price : 3.60 Ltr -USD 6.6 18 Ltr- USD 27.8
Zinc Enriched Red Oxide Primer Price : 0.90 Ltr - USD 2.2 3.60 Ltr -USD 7.4 18 Ltr- USD 31.1
Brighto Epoxy Zinc Chromate Primer Price : 3.60 Ltr -USD 29.7 18 Ltr- USD 112.4
Neo has extensive range of primers based on Epoxy / PU / Synthetic Resins. NEO PRIME GUARD grades are quality Epoxy based primers while NEO SHIELD PRIME grades are PU primers. These are used as a primer. They exhibit excellent adhesion properties and will stick to bare metal, Paints, primers, and fillers. They are used as a anti corrosive / protective primers. Neo offers multiple grades loaded with special additives, pigments for meeting specific requirements.
Odorless, acrylic-based primer, antibacterial, antifungal, penetrates deep into the surface, strengthens the outer layer. Reduces paint consumption, as the ability of the surface to absorb paint decreases. Used for painting and puttying. Per canister 10L
Fast-drying primer for heavily used iron structures. The zinc dust primer is suitable for the long-term passivation of iron and steel, even when they are in an aggressive atmosphere. Size 1 kg 5kg 20kg The zinc dust primer contains micronized zinc dust and an epoxy ester resin as a binder base. The product has cathodic rust protection properties and also has a sealing effect. The zinc dust primer is suitable for the long-term passivation of iron and steel, even when they are in an aggressive atmosphere. The product can be used on sandblasted steel components and structures as corrosion protection, as well as for steel equipment, pipes and body parts Weight 0.3kg Size 1kg, 5kg, 20kg
Product Category- Paint & Primers Product Name- Scottseal Description of the product- Acrylic Primer Area of Use (Application)- Interior and exterior walls Category (For Painters, Carpenters, etc.)- Painters USP of the product- 1. High covering ability 2. Reduces the porosity of the surface 3. Good binding property to the surface Area of application- Interior & Exterior
Product Category- Paint & Primers Product Name- Scott WP Description of the product- Interior Primer Area of Use (Application)- Internal walls Category (For Painters, Carpenters, etc.)- Painters USP of the product- Increases the coverage of top coat and decreases the porosity of the surface Area of application- Interior
Product Category- Paint & Primers Product Name- Scott IP Description of the product- Internal primer for acrylic paints Area of Use (Application)- Internal walls Category (For Painters, Carpenters, etc.)- Painters USP of the product- 1. Good brushability 2. High coverage with superior finish Area of application- Interior
WALL PROTECT Exterior Primer is a water-based wall coating suitable for application on exteriors as an undercoat to exterior emulsions. FEATURES :- 1. Excellent opacity and whiteness 2. Improves appearance of top coat 3. Does not chalk and can be applied on adequately cured fresh plaster 4. Does not require curing with water 5. Provides excellent adhesion to top coat emulsions 6. Prevents peeling off of top coat emulsions RECOMMENDED APPLICATION :- It can be used on all types of exterior cement plasters, exterior ceilings, asbestos sheets, concrete and existing painted surfaces. PRODUCT TECHNICAL DATA :- COLOURS : White FINISH : Smooth and Matt COVERAGE : 1 coat: 120-140 sq.ft/LTR (It may vary from the quoted coverage to factor such as method and condition of application and surface roughness) DRYING TIME : Surface drying time â?? 4-5 HOURS GLOSS LEVELS/SHEEN LEVELS : Silky smooth sheen FLASH POINT (IS101/108 Part 1, Sec 9) : Non- flammable SUITABILITY OF THINNER PAINT Use within 24 hrs. SHELF LIFE 18 months from date of manufacture in original tightly closed containers kept away from direct sunlight and excessive heat.
Description Two component metallic zinc rich epoxy high performance primer. Recommended Use :- The zinc pigment in dry film renders excellent protection to steel structure, tanks, bullets, dam gates, pipelines, plant equipments, jetty, etc. in both interior and exterior exposed conditions of fertilizer units, chemical plants, steel plants, cement plants, pulp and paper industries, ports, power plants, petrochemical and pharmaceutical industry, transformer, machines & other heavy duty OEMs. It also provides cathodic protection to steel and gives good resistance to corrosion at local damaged areas. It is useful in heavy-duty protective paint systems. It is recommended not to expose the primed coat alone to chemical and saline atmosphere for a long time. Physical Data COLOUR : Grey FINISH : Matt SOLIDS BY VOLUME : 50 �± 3% THEORETICAL SPREADING RATE : 10 sq.mt / ltr at DFT of 50 �µ FLASH POINT : Base : Above 23�°C Hardener : Above 23�°C DRYING CHARACTERISTICS (at 30�°C & at 65% Relative Humidity) : HARD DRY : Overnight FULL CURE : 7 days SHELF LIFE : BASE : 6 months HARDENER : 6 months Surface Preparation Abrasive blasting to minimum Sa 2 1/2 Standards is recommended with a profile of 35 - 75 microns. The surface should be absolutely dry and salt free before application. The primer should be applied preferably immediately or within 4 hours of blasting. Application Data :- MIXING RATIO : Base : Hardener (As per our recommendations) APPLICATION : By Brush / By Conventional Spray / By Airless Spray THINNER : Epoxy Thinner 190 POT LIFE : 4 hours min at 30�°C RECOMMENDED DFT : 30 50 µ. OVERCOATING INTERVAL : MIN : 8 hours MAX : Infinite COMPATIBILITY : Compatible with Epoxy, PU, Chlorinated Rubber intermediate/finish coat.
Two-component,water-based epoxy primer, high surface hardness, high moisture,water and chemical resistance, high mechanical resistance. It is excellent for bridging the water-based topcoat applications. There are no harmful chemicals in its composition.
WALL BIND ACRYLIC Cement Primer Water Thinnable No. Type WALL BIND Acrylic Interior Wall Primer (Water Thinnable) is suitable for useas a primer for painting of waterbased wall finishes such as distemper and plastic emulsions. 1 FEATURES WALL BIND has a special features are better whitness and opacity, easy brushing, excellent covering,alkali resistance,quick drying and good filling properties. Provides superior hiding and superior whiteness. 2 RECOMMENDED APPLICATION WALL BIND can be used for priming plastered wall,asbestose,brick work,cement concrete etc. PRODUCT TECHNICAL DATA No COLOURS White 1. FINISH Smooth and matt 2. COVERAGE 1 coat: 130-140 sq.ft/ltr 2 coats: 80-90 sq.ft/ltr (It may vary due to factors such as methods and conditions during application and surface roughness etc.) 3. DRYING TIME Surface drying time â?? 10-15 minutes 4. GLOSS LEVELS/SHEEN LEVELS NA 5. FLASH POINT (IS101/108 Part 1, Sec 9) Non- flammable 6. SUITABILITY OF THINNER PAINT Use within 24 hrs. 7. SHELF LIFE 12 Month from date of manufacture in original tightly closed containers away from direct sunlight and excessive heat. PERFORMANCE DATA 2. REMARKS a) Kindly refer to the MSDS for the saffro mellow coatings & resins Nano Acrylic Cement Primer which gives detailed information on Safety measures while handling the paint. b) Store the product at ambient conditions in well ventilate locations and away from the source of ignition and fire. c) Avoid eye and skin contact. In case of eye and skin contacts wash with plenty of clean water. d) Do not inhale or inject. In case of inhalation move to fresh air and seek medical attention. e) Use protective equipments like rubber/polythene gloves, safety goggle/glasses, face mask while handling. f) In humid areas, use of a bio-wash solution is recommended to remove surface fungus growth, fungal spores, mould etc. before application of the paint system. g) Do not apply when ambient temperature is less than 10�ºC or if the temperature might drop to this level within 4 hrs of application. h) Tinted paints need thorough shaking/mixing immediately after tinter addition as well as before use. i) For removing stains, sponge clean with a mild soap solution and wipe clean. Ensure drying time of 1 Week before cleaning.
Description Two component Epoxy based anti corrosive primer containing zinc phosphate as corrosion inhibiting pigments Recommended Use :- It is recommended as primer on M.S surface for OEM's as well as for process industries like fertilizers, refineries, chemicals and other plants. It can also be applied in diverse areas of tank exteriors, equipments, pipelines, structural steel, etc. Not to be used for immersion application. Physical Data :- COLOUR :- Yellow FINISH :- Matt SOLIDS BY VOLUME :- 40 �± 3% THEORETICAL SPREADING RATE :- 13.33 sq.mt. / ltr. at recommended DFT of 30 �µ FLASH POINT :- Base : 23�°C Hardener : 23�°C DRYING CHARACTERISTICS :- SURFACE DRY : 60 to 90 minutes (At 30�°C & 65% Relative Humidity) :- HARD DRY : Overnight. FULL CURE : 7 Days SHELF LIFE :- BASE : 6 months HARDENER : 6 months SURFACE PREPARATION Abrasive blasting to Sa 21/2 Swedish Standards is the best method of surface preparation. In case blasting is not possible, then the surface of steel should be cleaned to St-2/St-3 std. The surface should be absolutely dry, moisture and oil free before primer application Application Data MIXING RATIO :- Base : Hardener (As per our recommendation) APPLICATION :- By Brush / By Conventional Spray / By Airless Spray THINNER :- Epoxy Thinner 190 POT LIFE :- 4 hours min at 30�°C RECOMMENDED DFT :- 30 - 40 �µ. OVERCOATING INTERVAL :- MIN : 8 Hours MAX : 24 Hours COMPATIBILITY :- Can be over coated with Epoxy, PU, Chlorinated rubber and Oleo-resinous topcoats. Application Method Stir the Base part thoroughly. Mix the base and hardener as per our recommended ratio, by volume. Stir the mix gently to attain homogeneity. Allow the mixture to stand still (maturation) for about 10-15 minutes to initiate the reaction. Add Epoxy Thinner into the mix, if required, depending on application method, and stir gently for few minutes. Strain the paint through Nylon filter cloth and apply uniformly over the surface. All equipments used for above should be properly cleaned. Application : By Brush / By Conventional Spray / By Airless Spray Generally no thinner is required for Brush application; however under adverse environmental conditions about 5% of thinner, by volume, can be added. . Apply evenly in crossed manner, ensuring the uniform application. Use quality brushes for paint application. For Conventional Spray application:- Thinner : Epoxy Thinner 190 Addition : 10-15% Nozzle Orifice : 1.2 1.4 mm Nozzle Pressure : 40 - 70 p.s.i. For Airless Spray Application:- Thinner : Epoxy Thinner 190 Addition : Max 5% Nozzle Orifice : 0.37- 0.42mm Nozzle Pressure : 1400-1800 p.s.i.
Description Two component Epoxy based anti corrosive primer pigmented with Zinc Chromate as corrosion inhibiting pigments. Recommended Use :- It is recommended as primer on M.S surface for original equipment manufacturing as well as for process industry as in various fertilizer, refineries, petrochemical, chemical and other plants, applied in diverse areas of tank exteriors, equipments, pipelines, structural steel, etc. Not to be used for immersion application. Physical Data COLOUR : Assorted FINISH : Matt SOLIDS BY VOLUME : 40 ± 3% THEORETICAL SPREADING RATE : 13.33 sq.mt. / ltr. at recommended DFT of 30 �µ FLASH POINT : Base : Above 23�°C Hardener : Above 23�°C DRYING CHARACTERISTICS : SURFACE DRY : 60 90 minutes (At 65% Relative Humidity & at 30�°C) : HARD DRY : Overnight FULL CURE : 7 days SHELF LIFE : BASE : 6 months HARDENER : 6 months Surface Preparation Abrasive blasting to Sa 21/2 Swedish Standards is the best method of surface preparation. In case blasting is not possible, then the surface of steel should be cleaned to St-2/St-3 std. The surface should be absolutely dry, moisture and oil free before primer application. Application Data MIXING RATIO : Base : Hardener (As per our recommendations) APPLICATION : By Brush / By Conventional Spray THINNER : Epoxy thinner 190 POT LIFE : 4 hours min at 30 C RECOMMENDED DFT : 30 - 40 au. OVERCOATING INTERVAL : MIN : 8 hours MAX : 24 hours COMPATIBILITY : Can be over coated with Epoxy, PU, Chlorinated rubber and Oleo-resinous topcoats. Application Method Stir the Base part thoroughly. Mix the base and hardener as per our recommended ratio, by volume. Stir the mix gently to attain homogeneity. Allow the mixture to stand still (maturation) for about 10-15 minutes to initiate the reaction. Add Epoxy Thinner into the mix, if required, depending on application method, and stir gently for few minutes. Strain the paint through Nylon filter cloth of 100 mesh size and apply uniformly over the surface. All equipments used for above should be properly cleaned. Application :- By Brush / By Conventional Spray / By Airless Spray Generally no thinner is required for Brush application, however under adverse environmental conditions about 5% of thinner, by volume, can be added. Apply evenly in criss-cross manner and ensure the uniform application. Use quality brushes for paint application For Conventional Spray application :- Thinner : Epoxy Thinner 190 Addition : 10-15% Nozzle Orifice : 1.2 -1.4 mm Nozzle Pressure : 40-70 psi For Airless Spray application :- Thinner : Epoxy Thinner 190 Addition : 10-15% Addition : Max 5% if required Nozzle Orifice : 0.37- 0.42mm Nozzle Pressure : 1400-1800 psi
Description Two component Epoxy based anti corrosive primer containing red oxide and zinc chromate as corrosion inhibiting pigments Recommended Use :- Recommended as a primer on suitably cleaned mild steel surface in various fertilizer units, refineries, chemical and other plants, transportation industries, steel plants, cement plants, power plants, pulp and paper industries, pharmaceutical industries, etc. for application on tank exteriors, structural steel, pipelines, machineries, vessels, etc. The product is recommended as a primer for mild to moderate service conditions. Not to be recommended for immersed water condition Physical Data COLOUR : Red FINISH : Matt SOLIDS BY VOLUME : 40 + 3% THEORETICAL SPREADING RATE : 13.33 sq.mt / lt at recommended DFT of 30 FLASH POINT : Base : Above 23C Hardener : Above 23C DRYING CHARACTERISTICS (At 65% Relative Humidity & at 30C) : SURFACE DRY : 60 - 90 minutes HARD DRY : Overnight FULL CURE : 7 days SHELF LIFE : BASE : 6 months HARDENER : 6 months Surface Preparation Abrasive blasting to Sa 21/2 Swedish Standards is the best method of surface preparation. In case blasting is not possible, then the surface of steel should be cleaned to St-2/St-3 std. The surface should be absolutely dry, moisture and oil free before primer application Application Data :- MIXING RATIO : Base : Hardener (As per our recommendations) APPLICATION : By Brush / By Conventional Spray / By Airless Spray THINNER : Epoxy Thinner 190 POT LIFE at 30�°C : 4 hours min at 30�°C RECOMMENDED DFT : 30 40 �µ. OVERCOATING INTERVAL : MIN : 8 hours MAX : 24 hours COMPATIBILITY : Can be over coated with Epoxy, PU, Chlorinated Rubber and Synthetic Enamel finish paints. Application Method Stir the Base part thoroughly. Mix the base and hardener as per our recommended ratio, by volume. Stir the mix gently to attain homogeneity. Allow the mixture to stand still (maturation) for about 10-15 minutes to initiate the reaction. Add Epoxy Thinner into the mix, if required, depending on application method, and stir gently for few minutes. Strain the Application : By Brush / By Conventional Spray / By Airless Spray Generally no thinner is required for Brush application; however under adverse environmental conditions about 5% of thinner, by volume, can be added. Apply evenly in crossed manner, ensuring the uniform application. Use quality brushes for paint application. For Conventional Spray application :- Thinner : Epoxy Thinner 190 Addition : 10-15% Nozzle Orifice : 1.2 -1.4 mm Nozzle Pressure : 40-70 p.s.i. For Airless Spray application :- Thinner : Epoxy Thinner 190 Addition : Max 5% if required Nozzle Orifice: 0.37- 0.42mm Nozzle Pressure : 1400-1800 p.s.i.
Product Data Sheet GENERAL DESCRIPTION An easy-to-use, water-based primer specifically formulated to �¢??lock-out�¢?? corrosion on a wide range of metals. Applied correctly, is guaranteed for years. USES Suitable on sheet metal, castings, wrought iron, TNT Bar, steel Bar and steelwork. This product is not recommended for automotive use. COLOURS Available in natural green. SIZES Available in 4 litre,10 litre and 20 litre COVERAGE Up to 14 square metres per litre depending upon surface porosity and application method. APPLICATION Roller, brush, dip or airless spray. Provide adequate ventilation during use. DRYING TIMES Touch Dry Time - 20 minutes. Recoat Dry Time - 2 hours. Drying times refer to normal conditions (30�?�°C, 50% humidity). Under cooler, humid or still conditions, longer drying times may be necessary. DO NOT USE IN TEMPERATURES BELOW 10'c OR ABOVE 45C. DANGEROUS GOODS CLASSIFICATION Not classified as Dangerous Goods. SURFACE PREPERATION Previously Painted Surfaces : Scrape off loose and flaking paint and make sure the remainder is firmly attached. Sand glossy surfaces and enamels thoroughly and wipe clean. Remove all rust by abrasive blasting or mechanical sanding. Treat any remaining rust. Prime treated and bare areas with one coat SAFFRO Anti-Corrosive Metal Primer. In highly corrosive environments or within 2 kilometre of the sea, apply 2 coats of SAFFRO Anti- Corrosive Metal Primer. TNT BAR,STEEL BAR AND IRON: Remove all grease, dirt and other surface contaminants.Remove all rust by abrasive blasting or mechanical sanding. Treat any remaining rust with. Prime treated and bare areas with one coat SAFFRO Anti-Corrosive Metal Primer. In highly corrosive environments or within 2 kilometre of the sea, apply 2 coats of SAFFRO Anti- Corrosive Metal Primer
Description Two components, air drying, high build Epoxy primer. The product has the advantage of epoxy resin composition with specialty pigments, which facilitates one-coat, high build application for high performance. The product can be applied on minimum prepared surface and is designed to be completely wet and provide maximum intimacy with the substrate. Excellent adhesion is obtained on a variety of intact surfaces including over old coating and tightly adherent rust. With the high solids and less solvent content of the coating the risk of lifting, blistering, pin holing is reduced, and thus the risk of adhesion failure is minimized. Recommended Use :- It is recommended for steel structures in industrial plants, bridges, tank exteriors, oil tanks, pipes, marine atmosphere, cooling towers, etc. It has good resistance to spillage and fumes of acids, alkalis, fresh and salt water. Recommended as a primer on suitably cleaned mild steel surface in various Fertilizer units, Refineries, Chemical and other plants, Transportation industries, steel plants, cement plants, power plants, pulp and paper industries, pharmaceutical industries, etc. for application on tank exteriors, structural steel, pipelines, machineries, vessels, etc. Physical Data COLOUR : Selected Industrial shades FINISH : Matt SOLIDS BY VOLUME : 63 + 3% THEORETICAL SPREADING RATE : 8.4 sq.mt / lt at a recommended DFT of 75 FLASH POINT : Base : Above 25C Hardener : Above 25C DRYING CHARACTERISTICS (At 30C & 65% Relative Humidity) : HARD DRY : 16 - 18 hours FULL CURE : 7 days SHELF LIFE : Base: 6 months Hardener: 6 months Surface Preparation Abrasive blasting to Sa 21/2 Swedish Standards is the best method of surface preparation. In case blasting is not possible than manual cleaning by mechanical methods like wire brush, emery paper, hand / power tools, etc. to achieve St-2 / St-3 cleaning standards of Swedish specification. The surface should be free from moisture, oil, dust and dirt and should be absolutely dry before painting. Removal of loose rust is a must. Application Data :- MIXING RATIO : Base : Hardener (As per our recommendation ) POT LIFE : 2 hours at 30�°C APPLICATION : By Brush / By Conventional Spray / By Airless Spray THINNER : Epoxy Thinner 190 RECOMMENDED DFT : 75-100 �µ. OVERCOATING INTERVAL : MIN : 8 hrs. MAX : 24 hours (In case it is exceeded, the surface should be roughened byemery scuffing) OVERCOATABILITY : Epoxy, PU, Chlorinated Rubber and Synthetic Enamel intermediate &finish coat.
Specifications 1.odorless 2.low VOC 3.antimicrobial 4. mildew resistant 5.environmentally friendly 6.waterproof 7.Scrub resistance Description It is an enhanced mildew proof product adopting nano-scale Ag+ antimicrobial and mildew proof technology, integrating odorless formula, with fresh product smell, smooth paint film, durable and beautiful paint.As an affordable and environmentally friendly product with excellent decorative performance, it is characterized by fresh smell, environmental health, strong covering power, large painting area, convenient constructionapplication, short constructionapplication period, etc. Specification Data Solvent: Water Pigment: Non-lead pigment Theoretical Solids By Volume: more than 50% Theoretical Coverage: Theoretically 1 litre of this product covers 12 sqm in 1 coat Coverage varies considerably depending on application methods and surface roughness and porosity. Shelf Life: Minimum 12 months at 77F(25C) unopened and store in cool and dry places. Recommended Film Thickness: Wet: 80 micron Dry: 30 micron Dry Time: At 77F (25C) and 50% R.H. to recoat Touch Dry: 1 hours Recoat : 2-3 hours Application: Brush, Roll, conventional spray or Airless Spray. Thinner: Thin up 15% depend on different application methods & temperature. Do not over thin by adding more than 30% water. Brush or Roller: For sealing new or bare surfaces thin with up to 1 part of clean water to 5-10 parts of paint(10%-20%) Conventional Spray: Add up to 1 part clean water to 5 parts paint(20%) Airless spray: do not thin Clean-up: Clean up equipment with water Typical painting system Substrate System All kinds of Wall surfaces 1.Alkali Resistance Primer (1 coat) 2.Emulsion Wall Paint (2 coats)
