Transformer winding deformation test instrument based on the measurement of the characteristic parameters of transformer internal winding the internal fault frequency response analysis (FRA) method which is being developed in developed countries is adopted to make an accurate judgment of transformer internal fault. After the design and manufacture of transformer is completed the line coil and internal structure are determined. Therefore for a multi-winding transformer line coil if the voltage grade is the same and the winding method is the same the corresponding parameters (Ci Li) of each line coil should be determined. Therefore the frequency domain characteristic response of each line coil is determined accordingly and the frequency spectrum of the corresponding three-phase line coil is comparable to some extent. The distribution parameters of transformer windings will change when short-circuit between turns and phases occurs in the test process or collision occurs in the transportation process resulting in the relative displacement of the line coil and the deformation of the line coil caused by electromagnetic tension in the short-circuit and fault state during the operation process. Then it influences and changes the original frequency domain characteristics of the transformer that is amplitude change of frequency response and resonance frequency offset. The transformer winding test instrument developed according to the response analysis method is such a novel non-destructive testing equipment for transformer internal faults. It is suitable for the internal structure fault detection of 63kV ~ 500kV power transformer.
Transformer winding deformation test instrument based on the measurement of the characteristic parameters of transformer internal winding the internal fault frequency response analysis (FRA) method which is being developed in developed countries is adopted to make an accurate judgment of transformer internal fault. After the design and manufacture of transformer is completed the line coil and internal structure are determined. Therefore for a multi-winding transformer line coil if the voltage grade is the same and the winding method is the same the corresponding parameters (Ci Li) of each line coil should be determined. Therefore the frequency domain characteristic response of each line coil is determined accordingly and the frequency spectrum of the corresponding three-phase line coil is comparable to some extent. The distribution parameters of transformer windings will change when short-circuit between turns and phases occurs in the test process or collision occurs in the transportation process resulting in the relative displacement of the line coil and the deformation of the line coil caused by electromagnetic tension in the short-circuit and fault state during the operation process. Then it influences and changes the original frequency domain characteristics of the transformer that is amplitude change of frequency response and resonance frequency offset. The transformer winding test instrument developed according to the response analysis method is such a novel non-destructive testing equipment for transformer internal faults. It is suitable for the internal structure fault detection of 63kV ~ 500kV power transformer. product names Electric power transformer winding deformation test instrument Transformer winding deformation detector Transformer winding deformation meterTransformer winding deformation analyzer
Features: Non-toxic, non-irritation, flexible, Eco - friendly, durable, lightweight. Size and Color: Customized Usage: Storage/Decorative/Gift package Packing & Delivery: 1. Postage (For Retail Orders) Shipping companies that we use: + Airmail service of Vietnam Post Office (14 to 25 days) + Express mail service : TNT Express, UPS, DHL (3 to 6 days) 2. Sea/Air Freight (For Wholesale Orders) We offer the following options: + FOB (Free on Board) : We are responsible for the delivery of goods to the Da Nang port. This includes export tax from Vietnam and handling fees until the shipment is on board the ship. You are responsible for the ocean fee, the import customs clearance, the cargo insurance and other costs and risks. + CIF (Cost, Insurance and Freight): We are responsible for the delivery of goods to the requested destination port. This includes export tax from Vietnam and handling fees until the shipment is on board the ship, the ocean fee and the cargo insurance. You are responsible for the import customs clearance and other costs and risks.
- Production: Small Round Spoon - Material: Wood - Size and Color: Customized - Features: Non-toxic, non-irritation, flexible, eco-friendly, durable, lightweight - Usage: Storage/Decorative/Gift package - Packing & Delivery: 1. Postage (For Retail Orders) Shipping companies that we use: + Airmail service of Vietnam Post Office (14 to 25 days) + Express mail service : TNT Express, UPS, DHL (3 to 6 days) 2. Sea/Air Freight (For Wholesale Orders) We offer the following options: + FOB (Free on Board) : We are responsible for the delivery of goods to the Da nang port. This includes export tax from Vietnam and handling fees until the shipment is on board the ship. You are responsible for the ocean fee, the import customs clearance, the cargo insurance and other costs and risks. + CIF (Cost, Insurance and Freight): We are responsible for the delivery of goods to the requested destination port. This includes export tax from Vietnam and handling fees until the shipment is on board the ship, the ocean fee and the cargo insurance. You are responsible for the import customs clearance and other costs and risks.
Wooden Balancing Board is like a fancy toy, a swing, a bridge, a shop, a cabin, a stepping stone, a chair, a bridge, and so on, which helps kids turn what they imagine into reality. The Balancing Board is designed for body posture stimulation. Kidsâ?? balance will be strengthened when they stand on the wobble board with a high center of gravity. It supports the muscles responsible for the correct posture develops a sense of balance. Size: 105cmx38cmx20cm/ as required Colour: wooden
PE/PP mix color floor sweep (natural & blue color) = 6.8 tons PE mix color floor sweep with fillers, color concentrates, etc (Dark & Light colors) = 13.6 tons Minimum quantity: 1 x 40ft HC container (18 tons) - available for shipment in 10 days. Price: US$198.00 / MT Ex-warehouse Houston, TX, USA.
Virgin recycle 100% cotton polyester spun yarn ,viscose , bamboo, modal, tri blends, acrylic blended yarns ,tr tc, pv ,pc ,cotton ,nylon linen,modal blend , melange, sewing thread, csy yarns , aloe yarns, soy yarns , cotton yarns, poy,fdy ,dty texturised , denim yarn sizing waste aloevera yarn, soya bean, imitation jewellery brass jewellery, glass beads, alloy ,stainless steel artificial jewellery rings , bracelets, earrings, bracelets , necklace , rose gold plated jewellery , sterling silver fashion imitation jewellery ,cotton hard waste, sweeping waste , lickerin drop a. counts :1/1 to 120/1 b. multi ply 2 ply , 3 ply , upto 12 ply c. mvs vortex, ring, siro compact, siro spun, high twist , tfo, open end , doubled yarns , cationic dyeable ,d. fibres : lenzing,eccovero,lyocel,tencel e. color raw white ,dyed as per pentatonic shade f.certifications: primark, pscp , ic2, oekotex,grs,organic,gots, fibre certificate g. weaving/unwaxed & knitting /waxed yarns.
ProductSweep outlets BrandRenaissance Pipe Fitting Inc SizesRefer the specification ConditionNew Rating39 based on 9 reviews priceStart from 10 USD RFP India is a renowned exporter manufacturer and supplier of Socket Weld Outlet Fittings in the steel market industry worldwide Sweep Outlets is relatively like a pipe saddle On the other hand it has been manufactured in such a way by means of regard to trim down the pipe stresses and stress concentration features The weld is able to be look at by emblematic weld inspection ways such as radiography and ultrasound inspections In the meantime they have sturdy seamless manufacture dimensional sturdiness and accurateness The offered outlet is widely used for pipe connection in industries They are made up of different grades of standard ranges and meet its terms all the way through international and national standards RANGE Outlets to 24 in 3000 LBS 6000 LBS 9000 LBS available with NACE MR 0175 Stainless Steel Sweep Outlets Standard ASTM ASME ASA 182 Grade F 304 304L 304H 309S 309H 310S 310H 316 316TI 316H 316L 316LN 317 317L 321 321H 347 347H 904L Duplex Steel Sweep Outlets Standard ASTM ASME ASA 182 Grade F 44 F 45 F51 F 53 F 55 F 60 F 61 Aluminium Sweep Outlets Standard ASTM B247 B361 Grade 2024 6061 6063 6101 7075 Titanium Sweep Outlets Standard ASTM B381 Grade Grade 1 Grade 2 Grade 4 Grade 5 Grade 6 Grade 7 Grade 9 Grade 19 Grade 23 Carbon Steel Sweep Outlets Standard ASTM A 105A694 A350 LF3A350 LF2 Grade F42465256606570 Low Temperature Carbon Steel Sweep Outlets Standard ASTM A 350 LF2 A350 LF3 Alloy Steel Sweep Outlets Standard ASTM A182 Grade F1F5F9F11F22F91 Copper Alloy Sweep Outlets Standard ASTM ASME SB 61 62 151 152 Grade UNS NO C 70600 CU NI 9010 C 71500 CU NI 7030 C 71640 Nickel Alloy Sweep Outlets Standard ASTM ASME SB 564 160 472 Nickel 200 UNS N02200   Nickel 201 UNS N02201   Monel 400 UNS N04400 Monel K500 UNS N05500   Inconel K600 UNS N06600   Inconel 601 UNS N06601 Inconel 625 UNS N06625   Inconel 800 UNS N08800   Inconel 800H UNS N08810 Inconel 825 UNS N08825   Hastelloy C276 UNS N10276   Alloy 20 UNS N08020 OTHER Hydraulic Fittings   Instrumentation Fittings Test Certificate Manufacturer Test Certificate as per EN 10204 31 nbsp Types Of Sweep Outlets SS 310 310S Sweep Outlets Duplex Steel UNS S31803 Sweep Outlets Stainless Steel 304 304L Sweep Outlets Duplex Steel Sweep Outlets Stainless Steel 316 316L Sweep Outlets Duplex Steel UNS S32205 Sweep Outlets Stailess Steel 321 321H Sweep Outlets Super Duplex UNS S32750 Sweep Outlets Monel 400 Sweep Outlets Hastelloy C276 Sweep Outlets SS Sweep Outlets Steel Sweep Outlets Inconel 625 Sweep Outlets Alloy 20 Sweep Outlets CuNi 7030 C71500 Sweep Outlets CuNi 9010 C70600 Sweep Outlets ASTM A105 Sweep Outlets ASTM A350 LF2 LF3 Sweep Outlets Inconel 600 Sweep Outlets Hastel
Brown Sugar from Nzac Foods: Brown sugar is made of crystalline sucrose combined with a small amount of molasses, which is responsible for its characteristic color and rich flavor. Brown sugar is a sucrose sugar product with a distinctive brown color due to the presence of molasses. Brown sugar contains slightly more minerals and marginally fewer calories than white sugar.
A concentrated oil containing aromatic compounds from a plant. Essential oils are responsible for the scent of the plant and are most often found in the flowers and leaves.Essential oils are used in aromatherapy, massage therapy and in other alternative therapies and can also be found in products such as soaps, lotions, bath salts and candles.
Application: High frequency coaxial cable, wire network, tram line Insulation Material: noninsulated Conductor Material: Copper Clad Steel Conductor Type: Solid Type: Bare Place of Origin: India and China
Ramming mass is commonly used in metallurgy, building materials, non-ferrous metal smelting, chemical, machinery and other manufacturing industries. Ramming mass is widely used in non-core intermediate frequency furnace and core induction furnace. As an intermediate frequency furnace ramming material, refractory ramming is applied to melt gray cast iron, nodular cast iron, malleable cast iron, vermicular cast iron, and cast alloy steel; to melt carbon steel, alloy steel, high manganese steel, tool steel, heat resistant steel, stainless steel, molten aluminum and its alloys; to melt red copper, brass, white brass, bronze and its alloys, etc. Induction furnaces are used for melting cast iron, mild steel and various alloy steels in foundries and making of steel in mini steel plants using sponge iron The refined high silicon, low iron quartz sand and quartz powder are selected and the fused quartz sand is added as the refractory material., with no slag, no crack, damp proof, convenience of repair, and the corrosion resistance, thus greatly improving the furnace service life span and the economic benefit.. Silica ramming mass can safely be used up to an operating temperature of 1600 deg C. Since it expands very little, it is superior to both alumina and magnesia refractories to resist thermal shocks Acid ramming material is the premixed ramming mass of the lining material. The acid ramming mass is used to smelt a series of metal materials such as ordinary steel and carbon steel. The lining practice best suited to a particular furnace depends upon the capacity and design of the furnace, operation practice adopted during making of a heat, and furnace output.
Spruce is light and soft, but nevertheless has good strength and elasticity properties for its relatively light weight. It is not very susceptible to shrinkage and when dried remains stable. Its low natural durability can be compensated for by applying a protective coat of paint. Sourced from meticulously selected spruce trees, our Spruce Wood for industrial purposes is of the highest quality. Each piece of wood is processed using advanced techniques to ensure consistency and durability. Available in various dimensions to suit different industrial requirements. Responsibly harvested and processed to meet environmental standards
The natural colour of Mango wood is most often golden brown although there are also variations that have a more yellow tint or feature black or pink streaks across its surface The wood is often beautifully discoloured due to spalting where wood can change different colours as a result of fungus Exquisite Beauty Each piece of Mango Wood boasts a rich natural grain pattern and a warm inviting color palette making it a stunning choice for furniture decor and artisanal creations Sustainable Sourcing We prioritize sustainability by ethically sourcing mango wood from responsibly managed forests ensuring minimal environmental impact while supporting local communities Exceptional Durability Mango Wood is renowned for its robustness and resilience making it ideal for longlasting furniture pieces that withstand the test of time Versatile Applications From elegant dining tables to intricate carvings and everything in between Mango Wood lends itself to a myriad of creative applications limited only by your imagination Ease of Workability Craft with ease thanks to Mango Woods excellent workability allowing for effortless shaping carving and finishing to achieve your desired aesthetic
Rubberwood is a light-colored medium-density tropical hardwood obtained from the Par�¡ rubber tree (Hevea brasiliensis), usually from trees grown in rubber plantations. Rubberwood is commonly advertised as an â??environmentally friendlyâ?? wood, as it makes use of plantation trees that have already served a useful function. Superior Durability: Our Rubberwood undergoes a rigorous treatment process to enhance its strength and resilience, ensuring long-lasting performance in demanding industrial environments. Precision Machinability: Engineered with precision in mind, our Rubberwood is specifically designed to deliver consistent results when subjected to various machining operations, facilitating seamless integration into production processes. Sustainable Sourcing: We are committed to sustainability, sourcing our Rubberwood from responsibly managed plantations to minimize environmental impact and support ethical forestry practices. Versatile Applications: From furniture manufacturing to construction, our Rubberwood is highly versatile, offering endless possibilities for innovative industrial projects. Cost-Effective Solution: With its competitive pricing and exceptional quality, our Rubberwood provides unbeatable value for businesses looking to optimize their manufacturing processes without compromising on performance
Elevate your industrial projects with our premium Finger Joint Woodboard, meticulously crafted to meet the rigorous demands of the manufacturing sector. Designed for durability, sustainability, and versatility, our woodboards are optimized to enhance efficiency and performance across a myriad of applications. Precision Finger Joint Construction: Engineered with precision finger joint technology, ensuring superior strength and stability for industrial applications. High-Quality Materials: Crafted from select hardwoods, our woodboards boast exceptional durability and resilience, capable of withstanding heavy-duty usage. Environmentally Friendly: Committed to sustainability, our woodboards are sourced from responsibly managed forests, minimizing environmental impact while promoting renewable resources. Uniform Dimensions: Each woodboard is precisely machined to uniform dimensions, facilitating seamless integration into manufacturing processes and minimizing waste. Versatile Applications: From furniture manufacturing to construction projects, our Finger Joint Woodboards excel in a wide range of industrial applications, offering unparalleled adaptability
PRE ORDER / PRODUCTION FOB Thailand ( Laem Chabang Port ) KC 500; Nitrile Examination Gloves MOQ: 5 Million x 12 months MAX: 20M x 12 months Price USD8.00 KimTech; Nitrile Examination Gloves MOQ: 5 Million x 12 months MAX: 20M x 12 months Price USD8.20 *Including USD0.10 commission for buyer side *Sea Freight USD0.35 - USD0.50 CIF Payment terms : 1. SBLC as Warranty, amounting Half Value of First Month Delivery and or 2. Irrevocable Revolving Non Transferable Divisible LC with withdrawal % from the LC as deposit from the total amount of 1 month. Standing Operative Procedure; 1. NCNDA via Docusign 2. Buyer issues LOI, ICPO, LOA (if Proxy) and Proof Of Fund (*via Ready Willing Able or RWA Letter from the Buyer's Bank) for Fund verification, KYC 3. Within 24 to 48 hours of receiving the above Documents after verification, Buyer will be provided with a Draft Sales Purchase Agreement and LC Draft 4. Once the Buyer has reviewed the SPA, the Buyer and Seller will sign SPA - IMFPA. 5. Allocation Letter @ Authorization Letter will be provided thru the Zoom Meeting 6. Seller provides PI 7. Within 3 working days after the contract assigned, Buyer activate Letter of Credit @ Irrevocable Revolving Non Transferable Divisible LC to Seller with the following terms As Note given accordingly 2.5% - 10% payment withdrawn from the IRTLC for the deposit against Confirmation Letter from Factory and Invoice from Seller from the total amount of 1 month 90% - 97.5% will be withdrawn upon completion of SGS and ready for shipment for the First Month and 100% subsequently (to be confirmed by issuing bank) or value including the full purchase price plus the 2.5% - 10% one month sales for Deposit 8. PRODUCTION START 9. Seller provide delivery schedule from Factory within 10 - 15 working days after receipt of LC. If not Seller pay penalty 2.5% of 1 Month of Sales 10. Buyer provide SGS Inspection details to Seller to get approval from Factory for the Inspection 11. SGS is completed at the factory warehouse and after receive full payment the goods release from the Warehouse. 12. Seller released original documents to Buyer : Certificate of Origin, Packing List, Pro Forma Invoice 13. The Seller is responsible for the goods until they are loaded on a shipping vessel of which point all liability, risks, insurance and costs shifted to the buyer 14. TRANSACTION COMPLETE NOTE; 1.1Mil Deposit 10% 2. 5Mil Deposit 5% - 7% 3. 10M Deposit 3% - 5% 4. 20M Deposit 2.5%
meatball making machine meatball forming machine meatball process line/production line with frequency control and no-frequency control . The meatball forming machine adopts continuous output meatball system, which has high production efficiency, and is equipped with knives and shapers of different caliber, which can be replaced at will according to the requirements of users. The machine is mainly used to produce chicken balls, fish balls, shrimp balls, pork balls, beef balls, mutton balls, donkey balls, vegetable balls, seafood balls and other products. The main equipment of meatball production line includes meat planer, mincing machine, chopping and mixing machine, stuffing mixing machine, meatball machine, forming water tank, frying production equipment, etc. The machine is small in size, light in weight, low in noise, beautiful and generous, durable, easy to operate and maintain, efficient and energy-saving. The meat (FISH) balls produced are of good quality, smooth appearance, good roundness and uniform size. The frame body is made of 3mm thick stainless steel by bending and welding, which is solid for internal use. Wear resistant brass is used inside and outside the outlet. Capacity 50-500pcs/min ,meatball diameters : 16-40mm, above 40mm big size meatball can customized mould .
HIPS Regrind White-Mix Thermoplastic PS has two representatives as GPPS and HIPS resin. In particular, PS HIPS plastic is more popular thanks to many advantages and applications. PS HIPS belongs to the group of hard, transparent resins that are easy to color, machined by suction lamination method and easy injection technology. Common HIPS applications: In packaging technology, it is used as a single-layer packaging for products that do not require strict antioxidant requirements. Make coating HIPS plastic film to increase water vapor and gas resistance. Making a printing surface to increase printing ability, making the outer plastic packaging with the ability to tear easily and create gloss. Making bottle caps, pen cases, jewelry boxes, beer tanks, fresh food containers. Making pharmaceutical bottles, pipes, cap for solvent containers. Making high-frequency insulating materials, insulation clamps. Making imitation leather sandals, textile packaging. Pressing students' tables and chairs, pressed motorcycle details, yogurt cup, plastic candy tray. MATERIAL: HIPS Regrind White-Mix CATEGORY: HIPS TYPE: Regrind White-Mix SPECIFICATION Product- HIPS regrind post production from Yogurt caps Contamination â?? up to 2% foil metalizing (cover of the yogurt caps). Food grade material Post - industrial Sheet Extrusion & Vacuum forming Origin: Spain LOADING WEIGHT: 24 Ton FOB (USD/Ton): 650$ - 850$ Packaging: Jumbo Bag Est. Shipping Time: 15, 30, 45 days
HIPS Regrind from post consumer materials Thermoplastic PS has two representatives as GPPS and HIPS resin. In particular, PS HIPS plastic is more popular thanks to many advantages and applications. PS HIPS belongs to the group of hard, transparent resins that are easy to color, machined by suction lamination method and easy injection technology. Common HIPS applications: In packaging technology, it is used as a single-layer packaging for products that do not require strict antioxidant requirements. Make coating HIPS plastic film to increase water vapor and gas resistance. Making a printing surface to increase printing ability, making the outer plastic packaging with the ability to tear easily and create gloss. Making bottle caps, pen cases, jewelry boxes, beer tanks, fresh food containers. Making pharmaceutical bottles, pipes, cap for solvent containers. Making high-frequency insulating materials, insulation clamps. Making imitation leather sandals, textile packaging. Pressing students' tables and chairs, pressed motorcycle details, yogurt cup, plastic candy tray. MATERIAL: HIPS Regrind from post consumer materials ,Yes No Fr, NO pc abs, no iron, no circuit etc CATEGORY: HIPS TYPE: Regrind SPECIFICATION: Hips from post consumer materials.Yes No Fr, NO pc abs, no iron, no circuit etc. Hips per month 52 mt Origin: Bangladesh LOADING WEIGHT: 24 Ton FOB (USD/Ton): 650$ - 850$ Packaging: Jumbo Bag Est. Shipping Time: 15, 30, 45 days
