* PHOSCAST Phoscast : Phosphate Bonded Castables * PURPOSE customers using FBC boilers (Particularly underbed feed FBC boilers) for the protection of inbed coils against erosion potential by applying highly abrasive resistant refractory on inbed coils above fuel feed system. BACKGROUND * Two of such actions are providing special alloy studs on inbed coils and applying highly abrasive resistant refractory on the outer bottom loops of inbed Coils which are above the fuel feed nozzles. * GANESHAS has taken number of approaches to identify the key factors affecting erosion rates with an objective to enhance the life of inbed tubes as well as implementing the corrective action to reduce the erosion rates. Phosphate coatings are often used to protect steel parts against rusting and other types of corrosion * Erosion of inbed coils in fluid bed combustor is unavoidable phenomenon however the rate of metal wastage and thus the life of tubes depends on various factors like ash & fuel properties, design of Combustor / feeding system, flue gas velocities operating conditions etc. It has been also observed that maximum erosion prone inbed coils are those which come above fuel feed nozzles and an area of approximately 1 to 1.5 mts around fuel feed systems are badly affected. APPLICATION Phoscast-90 XR can be applied by ramming with wooden mallet having adequately large head @" dia x 5" length x 10â?? Jong handle). The desired lining or repair thickness is built up in several courses while ramming the mass to uniform thickness. Phoscast refractory should never be trawled to obtain smooth surface; ramming only should finish surface. Any excess mass is to be sliced off with trowel edge and then finished by ramming again for bed coil. Tube application of AFBC boiler, the material pasty mass should be finger pressed into the studs of the tube with maximum force. Finish should be given by pressing the hand palm against material applied, using surgical type thin rubber hand gloves.
Olive Cherry Date seeds Removing Machine Fruit seeds stone Removing machine series fruit different capacity different ,machine are little different ) Apricot kernel remover stone /core removing machine Peach core remover Apricot,Peach,Jujube nut removing machine Red date/Peach and apricot /Green plum / Cherry /Hawthorn /Sandberry /Iraq date /Date de /Marinated peach kernel machine Olive /Li Zi /Nut and butter/Litchi/ Pear stone removing machine Longan /Automatic stone core removal machine of large-scale red date automatic jujube type /Hawthorn / Beach date /Prunus cherry and so on ...about 20-40kind fruit can be stone removing machine Technology advantage : 1. The full-automatic equipment has high degree of automation. The mold conveyor belt can automatically feed and send materials to carry out transportation and core flushing. It only needs to pour the fruit into the feed hopper to complete the separation effect of core and flesh. It can work continuously and solve the problems of low efficiency, labor-consuming and time-consuming of manual core removal. 2. The structure of the machine is composed of stainless steel thick wall square tube and channel steel welding, which makes the equipment more stable during start-up and operation. All parts are assembled with bolts, which makes the operation and maintenance of the equipment more convenient. 3. The raw material of the equipment is made of stainless steel, which meets the hygienic standard of food processing equipment. The conveyor belt is made of imported polyurethane material, which is wear-resistant, tensile, tear resistant and has a longer service life. 4. The operation of the machine is simple and convenient, without long-term care. One person can manage multiple machines at the same time. The transmission system adopts advanced design concept and standardized components. The principle of core punching adopts the process of machine tool to punch the core, so that each equipment meets the high design standard, so that the effect of core removing is good, and the fruit shape is completely unchanged.
Cherry Olive Date Seeds Removing Machine are necessary machine for fruit process . Fruit Seeds Removing machine series fruit different capacity different ,machine are little different ) Apricot kernel remover stone /core removing machine Peach core remover Apricot,Peach,Jujube nut removing machine Red date/Peach and apricot /Green plum / Cherry /Hawthorn /Sandberry /Iraq date /Date de /Marinated peach kernel machine Olive /Li Zi plum /Nut and butter/Litchi/ Pear nuclear machine Longan /Automatic nuclear removal machine of large-scale red date Semi automatic small jujube type /Hawthorn / Beach date /Prunus cherry and so on ... Technology advantage : 1. The full-automatic equipment has high degree of automation. The mold conveyor belt can automatically feed and send materials to carry out transportation and core flushing. It only needs to pour the fruit into the feed hopper to complete the separation effect of core and flesh. It can work continuously and solve the problems of low efficiency, labor-consuming and time-consuming of manual core removal. 2. The structure of the machine is composed of stainless steel thick wall square tube and channel steel welding, which makes the equipment more stable during start-up and operation. All parts are assembled with bolts, which makes the operation and maintenance of the equipment more convenient. 3. The raw material of the equipment is made of stainless steel, which meets the hygienic standard of food processing equipment. The conveyor belt is made of imported polyurethane material, which is wear-resistant, tensile, tear resistant and has a longer service life. 4. The operation of the machine is simple and convenient, without long-term care. One person can manage multiple machines at the same time. The transmission system adopts advanced design concept and standardized components. The principle of core punching adopts the process of machine tool to punch the core, so that each equipment meets the high design standard, so that the effect of core removing is good, and the fruit shape is completely unchanged.
Fruit Stone Seeds Removing machine series fruit different capacity different ,machine are little different ) Apricot kernel remover stone /core removing machine Peach core remover Apricot,Peach,Jujube nut removing machine Red date/Peach and apricot /Green plum / Cherry /Hawthorn /Sandberry /Iraq date /Date de /Marinated peach kernel machine Olive /Li Zi /Nut and butter/Litchi/ Pear nuclear machine Longan /Automatic nuclear removal machine of large-scale red date Semi automatic small jujube type /Hawthorn / Beach date /Prunus cherry and so on ... Technology advantage : 1. The full-automatic equipment has high degree of automation. The mold conveyor belt can automatically feed and send materials to carry out transportation and core flushing. It only needs to pour the fruit into the feed hopper to complete the separation effect of core and flesh. It can work continuously and solve the problems of low efficiency, labor-consuming and time-consuming of manual core removal. 2. The structure of the machine is composed of stainless steel thick wall square tube and channel steel welding, which makes the equipment more stable during start-up and operation. All parts are assembled with bolts, which makes the operation and maintenance of the equipment more convenient. 3. The raw material of the equipment is made of stainless steel, which meets the hygienic standard of food processing equipment. The conveyor belt is made of imported polyurethane material, which is wear-resistant, tensile, tear resistant and has a longer service life. 4. The operation of the machine is simple and convenient, without long-term care. One person can manage multiple machines at the same time. The transmission system adopts advanced design concept and standardized components. The principle of core punching adopts the process of machine tool to punch the core, so that each equipment meets the high design standard, so that the effect of core removing is good, and the fruit shape is completely unchanged.
Fruit Seeds Removing machine series fruit different capacity different ,machine are little different ) Apricot kernel remover stone /core removing machine Peach core remover Apricot,Peach,Jujube nut removing machine Red date/Peach and apricot /Green plum / Cherry /Hawthorn /Sandberry /Iraq date /Date de /Marinated peach kernel machine Olive /Li Zi /Nut and butter/Litchi/ Pear nuclear machine Longan /Automatic nuclear removal machine of large-scale red date Semi automatic small jujube type /Hawthorn / Beach date /Prunus cherry and so on ... Technology advantage : 1. The full-automatic equipment has high degree of automation. The mold conveyor belt can automatically feed and send materials to carry out transportation and core flushing. It only needs to pour the fruit into the feed hopper to complete the separation effect of core and flesh. It can work continuously and solve the problems of low efficiency, labor-consuming and time-consuming of manual core removal. 2. The structure of the machine is composed of stainless steel thick wall square tube and channel steel welding, which makes the equipment more stable during start-up and operation. All parts are assembled with bolts, which makes the operation and maintenance of the equipment more convenient. 3. The raw material of the equipment is made of stainless steel, which meets the hygienic standard of food processing equipment. The conveyor belt is made of imported polyurethane material, which is wear-resistant, tensile, tear resistant and has a longer service life. 4. The operation of the machine is simple and convenient, without long-term care. One person can manage multiple machines at the same time. The transmission system adopts advanced design concept and standardized components. The principle of core punching adopts the process of machine tool to punch the core, so that each equipment meets the high design standard, so that the effect of core removing is good, and the fruit shape is completely unchanged.
* Pregnant Holstein Heifers Cattle * Fattening Beef Bulls * Hereford * Charolais * Limousin * Belgian Blue * Aberdeen Angus * Simmental beef cattle Type 1: Pregnant Holstein Heifers Weight: 400 to 800 Kg each Quantity: 3,000 Head Details: Pregnancy : 4 - 8 months, Milking Capacity: 30 and more litres per day, Age : 24 to 30 months Type 2: Heifers Bulls Weight: weight around 400-500 kg each Quantity: 2,000 Head Details: bulls for meat, Age : 6 to 18 months Type 3: Fattening Beef Bulls Weight: weight around 150-250 kg each Quantity: 2,000 Head Details: young bulls , Age : 3 to 10 Months Milking Capacity : 30 and more litres per day
PRODUCT INFO Broccoli consists of flowering heads that are harvested when the buds are unopened, small, and still green. The heads average 10 to 20 centimeters in diameter and grow on thick, fibrous stalks, emerging from a covering of large, leathery, dark green leaves. Broccoli heads are generally green, sometimes flushed with dark purple depending on the variety, and contain tiny, unopened buds attached to branching stems. The branching, segmented stems with the flower buds are known as florets, which connect into a larger, central, thick, and fibrous, pale green stem. The unopened buds have a crisp and tender consistency when raw, and if left to mature, the buds would produce bright yellow, four-petaled flowers. The thick, raw stems also have a crisp, crunchy, slightly chewy texture, and the leaves are edible but often contain a bitter, fibrous nature. When cooked, Broccoli develops a soft, semi-crunchy consistency and has vegetal, herbaceous, and earthy flavors with grassy, bittersweet nuances. Broccoli is a versatile ingredient well-suited for both raw and cooked applications, including steaming, boiling, roasting, baking, frying, and sauteing. The heads, stems, and leaves are all edible and will contain varying textures and flavors. The heads and stems are the most common portion of the plant consumed and can be chopped and tossed fresh into salads, mixed with other ingredients into slaws, or served on appetizer plates with creamy sauces and dips. Broccoli can also be battered and fried into tempura, lightly cooked and mixed into grain bowls, tossed into pasta, stir-fried with other vegetables, steamed and served as a tender side dish, or blanched and combined into rice and noodle dishes. In addition to using the heads in larger pieces, cooked Broccoli florets can be pureed into soups, stirred into risotto, or baked into quiches. The thick stems can also be used in any preparation calling for Broccoli. Some chefs choose to peel the stems to develop a more tender consistency when cooked. USES Broccoli leaves are also edible but may contain a bitter flavor. The leaves can be prepared similarly to kale or Swiss chard. Broccoli pairs well with zucchini, cauliflower, bell pepper, mushrooms, roasted meats, including poultry, turkey, beef, and fish, other seafood, sauces such as oyster, soy, creamy dressing, and vinaigrettes, and cheeses such as parmesan, cheddar, feta, and goat. Unwashed, raw Broccoli will keep 4 to 7 days when stored in the refrigerator, and once cooked, it will keep up to 5 days. It can also be frozen for 6 to 8 months. Season Broccoli is available year-round, with a peak season in the late fall through early spring.
Sprinkler head: aluminum alloy or abs plastic material, high strength, high quality, good price. Aluminum alloy material: 1.5inch. 2inch. 3inch 4hole. 3inch 6hole. 4inch 4hole. 4inch 6hole. 5inch 4hole. 6inch 4hole. 8inch 6hole. 10inch 8hole Plastic material: 1.5inch 4hole. 2inch 4hole. 3inch 4hole. 4inch 6hole. 5inch 6hole. 6inch 6hole. Model no.: 5 inch 4hole. Ventilation mode: mechanical ventilation. Air contact form: wet. Tower shape: round. Application fields: industrial. Condition: new. Nos of hole: 4. Trademark: newin. Cooling method: counter flow. Material: frp. Air contact way: open. Noise level: ordinary. Certification: csa, rohs, ur, iso, ul, ce, sgs, ccc. Size: 5inch. Application: round type cooling tower. Package: wood packing. Hs code: 84195000. Port:Shenzhen, china. Production capacity:50000pieces/year. Payment terms:L/c, t/t, western union.
1, Safe working load: 200kg 2, The back board folding angle: 70 3, The thigh board folding angle: 30 4.TR/ATR:0-20 5, The four motors automatically realize various positions. The motors are selected from internationally renowned brand Timotion, which are safe and noiseless. 6, Two control methods, operation handle control and guardrail built-in button operation, control handle is clear and easy to operate; built-in buttons on the side rail near headboard, graphic display, clear at a glance. The key has lock function, which reduces the probability of misoperation and locks safely. 7, Side rail: 1),Two side rail in each side of bed. 2),It can be automatically locked when raising, and each guardrail can bear more than 50KG. 3), Guardrail safety switch design, placed under the guardrail to avoid misuse of the patient; 4), Equipped with gas spring for easy operation. 5), The steel structure of the guardrail base is welded on the bed to ensure safety. 6), The 4-pieces guardrail has angle indicator that allows the caregiver to quickly and easily adjust the backrest angle and TR/ATR angle of the bed. 7),It equipped with guardrail built-in button to make it easier for the patient to operate the bed. 8, Casters 1), The four casters use 125mm center control one. 2), Steel structure, precision ball bearings are placed in the rotating head and the caster, the caster frame is equipped with a wheel cover made of synthetic material, suitable for locking the lever with a cam hole. Caster surface material: polyurethan, passed EN 12531 standard, single dynamic (force) load is not more than 175 kg, static load is not more than 200 kg 3),Braking system: Pedal-type synchronous braking arms on both sides of the bed, adopting all-metal structure, compact structure and reliable braking. 9, Shank board can be adjusted manually by simple steel support for convenience position. 10, At the 4 corners of the bed, there is an diameter HDPE anti-collision wheel which intergated on H/F board. 11, There are 1 hook in each side for drainage bag. 12, It equipped with manual CPR for emergency treatment.
Specification R50 R65 Rail Iron Profile Processing Train Used Rail Railway Track Railroad Steel Rails Railway Scrap Metal for Building Standard ASTM Grade Q235B Rail Heigth 120mm Bottom Width 120mm Web Thickness 28mm Head Width 70mm Length 6m Place of Origin China Zhejiang Brand Name zhongding Type Heavy Rail Application Railway Rail Weight QU70 Secondary Or Not Non-secondary Tolerance �±5% Alloy Or Not Non-Alloy Delivery Time 15-21 days Technique Hot Rollled Material Q235 Length 6m-12m production mode forge and press
Specification R50 R65 Rail Iron Profile Processing Train Used Rail Railway Track Railroad Steel Rails Railway Scrap Metal for Building Standard ASTM Grade Q235B Rail Heigth 120mm Bottom Width 120mm Web Thickness 28mm Head Width 70mm Length 6m Place of Origin China Zhejiang Brand Name zhongding Type Heavy Rail Application Railway Rail Weight QU70 Secondary Or Not Non-secondary Tolerance �±5% Alloy Or Not Non-Alloy Delivery Time 15-21 days Technique Hot Rollled Material Q235 Length 6m-12m production mode forge and press
Specification R50 R65 Rail Iron Profile Processing Train Used Rail Railway Track Railroad Steel Rails Railway Scrap Metal for Building Standard ASTM Grade Q235B Rail Heigth 120mm Bottom Width 120mm Web Thickness 28mm Head Width 70mm Length 6m Place of Origin China Zhejiang Brand Name zhongding Type Heavy Rail Application Railway Rail Weight QU70 Secondary Or Not Non-secondary Tolerance �±5% Alloy Or Not Non-Alloy Delivery Time 15-21 days Technique Hot Rollled Material Q235 Length 6m-12m production mode forge and press
Specification R50 R65 Rail Iron Profile Processing Train Used Rail Railway Track Railroad Steel Rails Railway Scrap Metal for Building Standard ASTM Grade Q235B Rail Heigth 120mm Bottom Width 120mm Web Thickness 28mm Head Width 70mm Length 6m Place of Origin China Zhejiang Brand Name zhongding Type Heavy Rail Application Railway Rail Weight QU70 Secondary Or Not Non-secondary Tolerance �±5% Alloy Or Not Non-Alloy Delivery Time 15-21 days Technique Hot Rollled Material Q235 Length 6m-12m production mode forge and press
Specification R50 R65 Rail Iron Profile Processing Train Used Rail Railway Track Railroad Steel Rails Railway Scrap Metal for Building Standard ASTM Grade Q235B Rail Heigth 120mm Bottom Width 120mm Web Thickness 28mm Head Width 70mm Length 6m Place of Origin China Zhejiang Brand Name zhongding Type Heavy Rail Application Railway Rail Weight QU70 Secondary Or Not Non-secondary Tolerance �±5% Alloy Or Not Non-Alloy Delivery Time 15-21 days Technique Hot Rollled Material Q235 Length 6m-12m production mode forge and press
Specification R50 R65 Rail Iron Profile Processing Train Used Rail Railway Track Railroad Steel Rails Railway Scrap Metal for Building Standard ASTM Grade Q235B Rail Heigth 120mm Bottom Width 120mm Web Thickness 28mm Head Width 70mm Length 6m Place of Origin China Zhejiang Brand Name zhongding Type Heavy Rail Application Railway Rail Weight QU70 Secondary Or Not Non-secondary Tolerance �±5% Alloy Or Not Non-Alloy Delivery Time 15-21 days Technique Hot Rollled Material Q235 Length 6m-12m production mode forge and press
Type Upright/Pendent/Sidewall/Concealed/ESFR Model ZSTZ ZSTX ZSTBS ZSTP ZSTDY ZSTY Nominal Diameter (mm): DN15 DN20 Connecting Threaded (Inch): 1/2" 3/4" Flux Coefficient: 80 115 Bulb Diameter: 5mm glass bulb for standard response 3mm glass bulb for quick response Response Time: 15seconds in general for 5mm glass bulb 8seconds in general for 3mm glass bulb Response Time Index RTI (ms)0.5: 87 for 5mm glass bulb 2225 for 3mm glass bulb
Main technical data Response time 15seconds in general for 5mm glass bulb 8seconds in general for 3mm glass bulb Response time index rti (m¡ï¿½ï¿½s)0.5 87 for 5mm glass bulb 22¡a25 for 3mm glass bulb
Main Technical Data Diameter DN15 DN20 Material Zinc Alloy or Brass Flux Coefficient 80 for DN15 115 for DN20 Max. Working Pressure 175 psig/1.2 mpa (12 bar) Factory Hydrostatic Test 100% @ 500psig (3.4 mpa) Min. Operating Pressure 7 psig/0.048 mpa (0.48 bar) Escutcheon Finish Chrome Plated or White Paint