Sintered Corundum Tabular Alumina Suppliers and Manufacturers

This is chemical setting Furan based chemical resistant mortar which is combination of Liquid and Powder, when mixed in proper proportion from workable mortar which after setting and curing give of liquid and give black highly cross linked composites. Furan When set and cured is resistant to highly corrosive acids, alkalis and to powerful organic solvents such as ketones, Aromatic and Chlorinated solvents. It has extreme resistant to Acidic & alkalis, Salts, Greases and Detergents. It resists to Organic & Inorganic acids at their boiling temperature. It is suitable against mild chlorine Gas (dry) phosphorous trichloride, pyridine at room temperature. Furan is especially useful where resistance to mixed media such as aqueous acids /alkalis and organic solvents is needed in chemical plant process and waste streams. Carbon filled Furan is used against corrosive effect of hydrofluoric acid & its salts. PREPARATION OF FURANE MORTAR : Mortar consist of Furan solution and Furan powder. The average mixing ratio necessary to obtain mortar with good working consistency is 1 part by weight Solution & 3 part by weight powder. The ratio will vary slightly depending on temperature and working conditions.Stir the liquid thoroughly before using. Place liquid in a suitable shallow mixing pan. Add powder by weight in the solution mix thoroughly and rapidly until all lumps are dispersed and the mortar is completely homogenous. Spread out the mortar in a thin layer, not more than ¾ thick, to dissipate the heat of reaction and lengthen the working life. Batch size can be varied depending upon the temperature and the speed with which the masons are working. Very large batches will become stiff quite rapidly. Make sure that all the Furan Motrar is used from the pan before another batch is mixed.When working at temperature above 40 C, very small batches not more than 2 Kgs, should be prepared. When working at temperature below 15C the liquid should be kept warm.

DATA SHEET FOR EPOXY EPOXY COATING :- INTRODUCTION - EPOXY COATING (HYB) is a two part high solids solvent free epoxy phenolic resin based coating system designed for hard wearing, smooth surface finish for floors, walls and on steel structures. Nonskid surface finish can be achieved on floor, if required. FEATURES: 1) Hard Wearing 2) Non Dusting 3) Excellent Surface Finish 4) Non Smelling 5) Good Aesthetics 6) Highly Chemical Resistant APPLICATION: 1.Stir well before mixing Part A and Part B and mix in the prescribed ratio. 2.Apply one coat of EPOXY primer on the clean and dry surface. 3.EPOXY COATING (HYB) should be applied on the surface by brush or roller within 24 hrs. After application of primer coat it should be allowed to air dry for min. 4 hrs. Preferable in a dust free atmosphere. 4.Apply min. 2 coats with the intercoat interval of 6-8 hrs. PRODUCT SPECIFICATIONS: Application - Brush, Roller Mixing Ratio - As Directed on Packing Port Life - 30 Mins. Drying Time - Touch Dry- 30 Min, Hard Dry 6 Hrs. - Intercoat Interval 6-8 Hrs. Min. - Dry Film Thickness 125-150 Microns/per coat - depending on porosity Covering Capacity - 6-8 sq.met/kg per coat depending on porosity, roughness & method of application. Color Shades - All Standard Shades RECOMMENDED USES: 1) Food & Pharmaceutical 2) Work Shop 3) Clean Room Application 4) Chemical Resistant Coating for Concrete& Steel 5) Petrochemical, Fertilizer plants METHOD OF APPLICATION: SURFACE PREPARATION The long-term durability of the applied Epoxy coating (HYB) epoxy coating is dependent on the adhesion between sub-base and coating material. It is most important therefore, that the substrate surfaces are correctly prepared prior to application. 1.Before application of the Epoxy coating (HYB) surface should be free from loose partials, rust, oils, grease or earlier coatings and should be totally dry. 2.New concrete or cementations surface should be placed at least 28 days and have a moisture content of less than 5% before application of Epoxy coating (HYB) 3.After surface is dry, all repair work like sealing of joints, cracks filling of cavities and crevices should be carried out. HEALTH & SAFETY - Keep the containers tightly closed when not in use. Avoid contact with skin & eyes. It comes in contact with the body, wash affected parts with plenty of water and contact a doctor. Other known sector for Epoxy floor lining, Epoxy garage floor lining, Concrete epoxy lining, Concrete floor epoxy lining, Epoxy pipe lining, Marine epoxy lining, Sub marine epoxy lining, Basement lining epoxy floor shield, Louisiana, Oregon, Chip lining color epoxy floor, Aviation lining epoxy interior.

Bitumen Primer * Bitumen Primer is Bituminous air curing ready mixed Acid & Alkali resistant special primer. Application * Concrete surface must be clean, dry and rough. No primer should be applied over smooth and wet surface. * After cleaning the concrete surface, one coat of Bitumen Primer should be applied with brush and allow to dry thoroughly. * The drying time will depend upon the temperature. * 24 Month at the temperature 30C (+2OC) Packing * Bitumen Primer: 25 Liter Drum Note * Bitumen Primer contains volatile and slightly toxic solvent. Keep away from spark and open flames at working area. * Bitumen premier it is manufactured using bitumen solution which is used for sealing of prime porous and non-porous surface, and also to protect residential and commercial building. * Bitumen Primer is used to protect substrate against corrosive attack, is suggested to apply anti-corrosive primer.It is best for protection against sub-striate against atmospheric corrosion and chemical corrosion. It is a mixed substance made up of organic liquids that are highly sticky, water proof, viscous,acid proof as with all surface coating, good Bitumen Premier is used for long life of the system. it is applied by brush or roller and allowed to dry before any water proofing treatment so to avoid solvent it is used in defects such as cracks, broken mortar joints, etc. are to be repaired prior to Bitumen primer application. Product Details: Grade Standard Technical Grade Physical State - Liquid Usage - Industrial Color - Black Characteristics: Appearance/Color - Pasty liquid/ black Chemical Base - Bituminous rubber emulsion. Density - 1.0 kg/l Curing Speed/ Rate - 3 - 4 hours Tack free after - 5 - 10 hours Cured after - 2 - 4 days (Dependent on ambient Solid Content by - temperature, substrate temperature, Weight - relative Water Content by weight - humidity and thickness of the coating) Bitumen Content - 41% by weight - Thixotropic (The viscosity can be adjusted by - Viscosity adding up to max. 5% of clean water. - Stir well prior use) - For light protection: 1.0 mm min. Coating - For greater protection: ~ 1.5 - 2.0 mm Thickness applied - in two coats. Water Penetration - 48 h, 1 bar: 78.5 cm2: 0 ml under Hydrostatic - 96 h, 4 bar: 78.5 cm2: 33 ml Pressure - Water vapor 6 x 10-7 mg / hmPa Permeability Service - -30 C to 200 C Temperature - Adhesion Concrete - Very good, Timber: Very good, Metal: Moderate Glass: Poor

PRODUCT DATA SHEET ACID RESISTANT BRICK Material : RED SHALE Type Acid Resistant Brick Size (mm) 230 (LENGTH) X 115 (WIDTH) X 100,76,65,50,40,38,30,25 (THICK) Specification : ASTM C279, ASTM C410, IS 4860-1982 DESCRIPTION : We offer premium quality acid resistant bricks Red â?? Shale , tiles and special shapes. We also offer customized sizes as per clients' requirements. Our acid bricks comply with ASTM C279 Type-III, ASTM C410 Type H, L, and Indian Standard 4860 - 1982 Class-I for all applications where low absorption and high acid resistance is required. FEATURES OF ACID RESISTANT BRICK: Excellent resistant against wide range of chemicals except hydrofluoric acid, high abrasion resistance, low wearing properties, High Thermal resistant to sudden change in temperature AREA OF APPLICATION: Chemical Analysis (Average) Acid and Alkali Storage Tank Farms Demineralization plants and Water treatment plants Chimney inside lining, FGD linings Towers and Columns Process Vessels and Tanks Sewerage Treatment Plants and Lines Industrial Flooring and Bund Areas Chimney and Flue Gas Linings Hoppers and Chutes SiO266.4 Al2 0324 TiO21.1 Fe2 O31.1 K2 O + Na2 O2.5 NOT RECOMMENDED: HF acid or other fluoride solutions Heavy thermal shock Typical Physical Properties of GANESHAS Acid and Chemical Resistant Brick Characteristic RED SHALE ACID RESISTANT BRICK Test Standard Bulk Density, gm/cc - 2.3 to 2.35 ASTM C-20 -Water Absorption, % - 0.1 to 1.5 IS 4860-1968 Apparent Porosity, % -0.5 to 1.75 S 4860 Acid Solubility (H2SO4), Loss in Mass,% -0.1 to 1.8 ASTM C-279 Modulus of Rupture, PSI -2133 to 3555 ASTM C-67 Compressive Strength, Kg/cm2 - 700-900 IS 4860-1968 Abrasion Resistant , Volume in mm3 -69 to 85 EN 102 Surface Hardness, MOHS Scale - 7

PRODUCT DATA SHEET ACID RESISTANT BRICK Material : FIRECLAY Type Acid Resistant Brick Size (mm) : 230 (LENGTH) X 115 (WIDTH) X 100,76,65,50,40,38,30,25 (THICK) Specification : ASTM C279, ASTM C410, IS 4860-1982 DESCRIPTION : * We offer premium quality acid resistant bricks Red â?? Shale , tiles and special shapes. We also offer customized sizes as per clients' requirements. Our acid bricks comply with ASTM C279 Type-III, ASTM C410 Type H, L, and Indian Standard 4860 - 1982 Class-I for all applications where low absorption and high acid resistance is required. FEATURES OF ACID RESISTANT BRICK: * Excellent resistant against wide range of chemicals except hydrofluoric acid, high abrasion resistance, low wearing properties, High Thermal resistant to sudden change in temperature AREA OF APPLICATION: Chemical Analysis (Average) Acid and Alkali Storage Tank Farms Demineralization plants and Water treatment plants Chimney inside lining, FGD linings Towers and Columns Process Vessels and Tanks Sewerage Treatment Plants and Lines Industrial Flooring and Bund Areas Chimney and Flue Gas Linings Hoppers and Chutes SiO266.4 Al2 0324 TiO21.1 Fe2 O31.1 K2 O + Na2 O2.5 NOT RECOMMENDED: HF acid or other fluoride solutions - Heavy thermal shock Characteristic Fireclay Type Acid Resistant Brick - Test Standard Bulk Density, lbs/ft3 - 2.25 to 2.30 ASTM C-20 Water Absorption, % - 0.1 to 1.8 ASTM C-20 Apparent Porosity, % - 4.05 to 4.14 ASTM C-20 Acid Solubility (H2SO4), Loss in Mass,% - 6.1 to 6.8 ASTM C-279 Modulus of Rupture, Mpa - 14.6 ASTM C-67 Compressive Strength, PSI - 15500 to 17250 ASTM C-67 Abrasion Resistant , Volume in mm3 - 71 to 96 EN 102 Surface Hardness, MOHS Scale - 7 Thermal Conductivity, BTU-in/hr-ft-F - 6.94 to 7.12 ASTM C-236 Thermal Expansion Coefficient,in/in/Fx10-6 - 2.6 to 2.8 EN 103

Acid / Alkali Resistant Tiles/Bricks * Our Acid proof tiles, Acid alkali resistant tiles, Chemical resistant tiles are fully vitrified tiles which are manufactured using special non ferrous clay, processed at extremely high temperatures this process causes the raw materials to fuse and form a compact mass with an extremely low water absorption of less than 0.5% resulting in the formation of a very strong body with a flexural strength of 38 N/mm2, solid through color fade proof with a very hard surface Mohs hardness of 7. * The acid resistant tiles come in a range of sizes and thicknesses from ranging from 8-25mm. Our acid proof tiles meet stringent specification norms of IS 4457:2007 and relevant ASTM/DIN standards which ensure excellent performance in Acid/Alkali/Chemical (expect Hydrofluoric acid and its derivatives). Corrosion Protection Applications * Factory Floors subject to corrosion from Chemicals, Acids, Oil & Solvents * Pickling tank and surrounding areas * Food & Beverage Industry flooring * Battery rooms and Control rooms * Demineralization plants * Walls of washing and Paint shop areas * Acid Resistant Tiles Manufacturers India * Our acid proof tiles provide excellent abrasion resistance, anti-skid properties for worker safety and high aesthetic appeal. We also provide specialized corner tiles for reducing chances for acid attack through construction joints. Our standard sizes are 200x100, 200x200 & 300x300 millimeters.

Sintered stone is a synthetic surfacing material made entirely of minerals and formed by heat, without any binders, unlike engineered stone or quartz countertops This material is highly durable, heat-resistant, scratch-resistant, and non-porous, making it ideal for countertops and bathroom vanities Sintered stone is created by intensely heating a selection of minerals and stone particles together with pressure to bond them, mimicking the natural stone formation process in just hours It is used for kitchen and bathroom countertops, flooring, wall cladding, and exterior facades due to its durability and large format options

We deals in the following Chemicals :- Dolomite Powder Mica Powder, Mica Flakes, Mica Blocks, Mica Sheets Quartz / Silica Powder, Quartz / Silica Lumps, Quartz / Silica Granules, Quartz / Silica Grits Bentonite Powder, Bentonite Lumps, Bentonite Granules, Bentonite Clay Barite Powder, Barite Ore Hematite / Iron Oxide Powder, Iron Oxide ( Ferric Oxide ) Ilmenite (Synthetic Rutile) Fly Ash Powder Alumina Silica ( Cenosphere ) Powder Calcium Carbonate Powder Magnetite, Cellulose Fibers, Cellophane Flakes, Walnut Shells

We deals in the following Chemicals :- Barite Powder, Barite Ore Dolomite Powder Mica Powder, Mica Flakes, Mica Blocks, Mica Sheets Quartz / Silica Powder, Quartz / Silica Lumps, Quartz / Silica Granules, Quartz / Silica Grits Bentonite Powder, Bentonite Lumps, Bentonite Granules, Bentonite Clay Hematite / Iron Oxide Powder, Iron Oxide ( Ferric Oxide ) Ilmenite (Synthetic Rutile) Fly Ash Powder Alumina Silica ( Cenosphere ) Powder Calcium Carbonate Powder Magnetite, Cellulose Fibers, Cellophane Flakes, Walnut Shells

We deals in the following Chemicals :- Calcium Carbonate Bentonite Powder, Bentonite Lumps, Bentonite Granules, Bentonite Clay Quartz / Silica Powder, Quartz / Silica Lumps, Quartz / Silica Granules, Quartz / Silica Grits Mica Powder, Mica Flakes, Mica Blocks, Mica Sheets Dolomite Powder Barite Powder, Barite Ore Hematite / Iron Oxide Powder, Iron Oxide ( Ferric Oxide ) Ilmenite (Synthetic Rutile) Fly Ash Powder Alumina Silica ( Cenosphere ) Powder Calcium Carbonate Powder Magnetite, Cellulose Fibers, Cellophane Flakes, Walnut Shells

We are supplier and exporter of Manganese Oxide. Manganese Oxide Fertilizer Grade: Application: The product is generally used by the fertilizer industry. Fertilizer Grade: Appearance: Fine greenish-brown powder Total Manganese (Mn): 54% +/- 2% Manganese Oxide (MnO): 68% Iron as Fe: 12% max. Silica as SiO2: 12% max. Alumina as Al2O3: 5% max. Manganese Dioxide (MnO2): 2% max. Screen analysis 100 mesh (BSS): 95-100% Passing. Manganese oxide Mn :- 44 - 46 % Mno2 :- 06 % max. Sio2 10 % max. Fe203 :- 08 % max. 50 kgs. Hdpe begs.

We deals in the following Chemicals :- Bentonite Powder, Bentonite Lumps, Bentonite Granules, Bentonite Clay Quartz / Silica Powder, Quartz / Silica Lumps, Quartz / Silica Granules, Quartz / Silica Grits Mica Powder, Mica Flakes, Mica Blocks, Mica Sheets, Mica Scraps Dolomite Powder Barite Powder, Barite Ore Hematite / Iron Oxide Powder, Iron Oxide ( Ferric Oxide ) Ilmenite (Synthetic Rutile) Fly Ash Powder Alumina Silica ( Cenosphere ) Powder Calcium Carbonate Powder Magnetite, Cellulose Fibers, Cellophane Flakes, Walnut Shells

We deals in the following Chemicals :- Quartz / Silica Powder, Quartz / Silica Lumps, Quartz / Silica Granules, Quartz / Silica Grits Bentonite Powder, Bentonite Lumps, Bentonite Granules, Bentonite Clay Mica Powder, Mica Flakes, Mica Blocks, Mica Sheets, Mica Scraps Dolomite Powder Barite Powder, Barite Ore Hematite / Iron Oxide Powder, Iron Oxide ( Ferric Oxide ) Ilmenite (Synthetic Rutile) Fly Ash Powder Alumina Silica ( Cenosphere ) Powder Calcium Carbonate Powder Magnetite, Cellulose Fibers, Cellophane Flakes, Walnut Shells

We deals in the following Chemicals :- Quartz / Silica Powder, Quartz / Silica Lumps, Quartz / Silica Granules, Quartz / Silica Grits Bentonite Powder, Bentonite Lumps, Bentonite Granules, Bentonite Clay Mica Powder, Mica Flakes, Mica Blocks, Mica Sheets, Mica Scraps Dolomite Powder Barite Powder, Barite Ore Hematite / Iron Oxide Powder, Iron Oxide ( Ferric Oxide ) Ilmenite (Synthetic Rutile) Fly Ash Powder Alumina Silica ( Cenosphere ) Powder Calcium Carbonate Powder Magnetite, Cellulose Fibers, Cellophane Flakes, Walnut Shells

Feldspar is the name given to a group of minerals distinguished by the presence of alumina and silica (SiO2) in their chemistry. This group includes aluminum silicates of soda, potassium, or lime. It is the single most abundant mineral group on Earth. They account for an estimated 60% of exposed rocks, as well as soils, clays, and other unconsolidated sediments, and are principal components in rock classification schemes. The minerals included in this group are the orthoclase, microcline and plagioclase feldspars. APPLICATIONS Glass making Ceramics Porcelain Electrodes Abrasion We at CEMENTATION produce Feldspar of minerals containing Potassium and Sodium. Our supply is available in Lumps, Granules and Powder form.

Introduction: - Feldspar is primarily used in industrial applications for its alumina and alkali content. Feldspar is a naturally occurring anhydrous, inorganic, igneous rock. The fusibility of the mineral makes it useful raw material for many applications and the purity is the indication of better fusibility in the application. There are two types of it depending On Na2O and K2O SODA FELDSPAR POTASH FELDSPAR Applications: - CERAMICS ENAMEL FRITZ & GLAZED INSULATORS GLASS MILD ABRASIVES PICTURE TUBES SANITARYWARE TABLEWARE VITRIFIED TILES WELDING ELECTRODE Available Mesh Size: - 100 - 500 MESH Custom sizes and Material of required specifications can be made in case of Bulk and Regular orders. TYPICAL CHEMICAL COMPOSITION OF POTASH FELDSPAR Index ompound Unit Result 1. Silica - (SiO2) % 66 - 68 2. Alumina - (AI2O3) % 17 - 18 3. Iron - (Fe2O3) % 0.03 - 0.06 4. Titanium - (TiO2) % 0.03 - 0.06 5. Calcium - (Cao) % 00.00 6. Magnesium - (MgO) % 00.00 7. Soda - (Na2O) % 2 - 3 8. Potash - (K2O) % 10 - 12 9. Loss on Ignition - (LOI) % 0.10 - 0.20 TYPICAL CHEMICAL COMPOSITION OF SODA FELDSPAR Index Compound Unit Result 1. Silica - (SiO2) % 68 - 72 2. Alumina - (AI2O3) % 17 - 18 3. Iron - (Fe2O3) % 0.10 - 0.15 4. Titanium - (TiO2) % 0.03 - 0.06 5. Calcium - (Cao) % 0.05 - 0.20 6. Magnesium - (MgO) % 0.10 - 0.15 7.Soda - (Na2O) % 9 - 10 8. Potash - (K2O) % 0.50 - 0.20 9. Loss on Ignition - (LOI) % 0.10 - 0.20

China Clay is a naturally hydrated Aluminum Silicate. It is one of the most abundantly available clay in the Earth's crust. Pure grade of China clay or kaolin clay produced by the processes of levigating. China Clay is also called KAOLIN, it is one of the essential Raw materials for Ceramic Industries, China Clay does not swell on adding water & Alumina present in Clay do not form Isomorphism series with any other metallic compound. Applications: - China clay products are immensely used in the manufacturing of ceramics, papers, paint colors, vitrified tiles, soap, ultramarine and in various other purposes Available Mesh Size : As per requirement Custom sizes and Material of required specifications can be made in case of Bulk and Regular orders.