Ram Arm Tractor Trailer Combine Part Suppliers and Manufacturers

Fly Ash: Fly Ash is by product generated during combustion of coal, and comprises the fine particles that rise with the flue gases. Ash which is collected from the bottom is termed bottom ash. Fly ash is collected by electrostatic precipitators or other particle filtration equipment before the flue gases reach the chimneys of coal-fired power plants and together with bottom ash removed from the bottom of the furnace is in this case jointly known as coal ash. Depending upon the type of coal being used, the specification of Fly Ash varies considerably, but Fly Ash contains substantial amounts of silicon dioxide and calcium oxide (CaO), both being endemic ingredients in many coal-bearing rock strata. We are a reputed Fly Ash Exporter based in India and are supplying Fly Ash different cement, ready mix concrete, steel, refractories and construction industries. The Major Utilization Areas Of Fly Ash : - Manufacture of Portland Pozzolanic Cement & Performance improver in Ordinary Portland cement (OPC). - Part replacement of OPC in cement concrete. - High volume Fly Ash concrete. - Roller Compacted Concrete used for dam & pavement construction. - Manufacture of ash bricks and other building products. - Construction of road embankments, structural fills, low lying area development. - As a soil amender in agriculture and wasteland development. Types of Fly Ash: - According to the type of coal used fly is classified into two types. Anthracite and bituminous coal produces Fly Ash classified as class F. Class C Fly Ash is produced by burning lignite or sub-bituminous coal. Class C Fly Ash has self-cementing properties. - Class F and Class C Fly Ash are products of the combustion of coal in large power plants. Fly Ash is collected in electrostatic precipitators or baghouses, and then transferred to large silos for shipment. When needed, Fly Ash is classified by precise particle size requirements, thus assuring a uniform, quality product. - Class F Fly Ash is available in the largest quantities. Class F is generally low in lime, usually under 15 percent, and contains a greater combination of silica, alumina and iron (greater than 70 percent) than Class C Fly Ash. - Class C Fly Ash normally comes from coals which may produce an ash with higher lime content generally more than 15 percent often as high as 30 percent. Elevated CaO may give Class C unique self-hardening characteristics. Minimum Order Quantity : 1 container

The unique combination of artisans between rattan and ceramic, creating a product that has always attracted the attention of tourists in all parts of the country.

Psyllium Husk is obtained from plantage ovate or Psyllium plant. Psyllium plant grows in the region which has good exposure to sunlight, and the soils are well drained and sandy. This is an annual crop cultivated largely in Gujarat and in some parts of Rajasthan and Madhya Pradesh. The Botanical name of Psyllium husk is Plantago Ovata, and it is better known as Isabgol in India. Psyllium is mucilage having a combination of xylose, aucubin, galacturonic, arabinose, semi drying fatty oils.

* PHOSCAST Phoscast : Phosphate Bonded Castables * PURPOSE customers using FBC boilers (Particularly underbed feed FBC boilers) for the protection of inbed coils against erosion potential by applying highly abrasive resistant refractory on inbed coils above fuel feed system. BACKGROUND * Two of such actions are providing special alloy studs on inbed coils and applying highly abrasive resistant refractory on the outer bottom loops of inbed Coils which are above the fuel feed nozzles. * GANESHAS has taken number of approaches to identify the key factors affecting erosion rates with an objective to enhance the life of inbed tubes as well as implementing the corrective action to reduce the erosion rates. Phosphate coatings are often used to protect steel parts against rusting and other types of corrosion * Erosion of inbed coils in fluid bed combustor is unavoidable phenomenon however the rate of metal wastage and thus the life of tubes depends on various factors like ash & fuel properties, design of Combustor / feeding system, flue gas velocities operating conditions etc. It has been also observed that maximum erosion prone inbed coils are those which come above fuel feed nozzles and an area of approximately 1 to 1.5 mts around fuel feed systems are badly affected. APPLICATION Phoscast-90 XR can be applied by ramming with wooden mallet having adequately large head @" dia x 5" length x 10â?? Jong handle). The desired lining or repair thickness is built up in several courses while ramming the mass to uniform thickness. Phoscast refractory should never be trawled to obtain smooth surface; ramming only should finish surface. Any excess mass is to be sliced off with trowel edge and then finished by ramming again for bed coil. Tube application of AFBC boiler, the material pasty mass should be finger pressed into the studs of the tube with maximum force. Finish should be given by pressing the hand palm against material applied, using surgical type thin rubber hand gloves.

This is chemical setting Furan based chemical resistant mortar which is combination of Liquid and Powder, when mixed in proper proportion from workable mortar which after setting and curing give of liquid and give black highly cross linked composites. Furan When set and cured is resistant to highly corrosive acids, alkalis and to powerful organic solvents such as ketones, Aromatic and Chlorinated solvents. It has extreme resistant to Acidic & alkalis, Salts, Greases and Detergents. It resists to Organic & Inorganic acids at their boiling temperature. It is suitable against mild chlorine Gas (dry) phosphorous trichloride, pyridine at room temperature. Furan is especially useful where resistance to mixed media such as aqueous acids /alkalis and organic solvents is needed in chemical plant process and waste streams. Carbon filled Furan is used against corrosive effect of hydrofluoric acid & its salts. PREPARATION OF FURANE MORTAR : Mortar consist of Furan solution and Furan powder. The average mixing ratio necessary to obtain mortar with good working consistency is 1 part by weight Solution & 3 part by weight powder. The ratio will vary slightly depending on temperature and working conditions.Stir the liquid thoroughly before using. Place liquid in a suitable shallow mixing pan. Add powder by weight in the solution mix thoroughly and rapidly until all lumps are dispersed and the mortar is completely homogenous. Spread out the mortar in a thin layer, not more than ¾ thick, to dissipate the heat of reaction and lengthen the working life. Batch size can be varied depending upon the temperature and the speed with which the masons are working. Very large batches will become stiff quite rapidly. Make sure that all the Furan Motrar is used from the pan before another batch is mixed.When working at temperature above 40 C, very small batches not more than 2 Kgs, should be prepared. When working at temperature below 15C the liquid should be kept warm.

1.Factory with 20 years farm tractor manufacture experence ensure the products quality. 2.Two years warranty period. 3.For easy-damage parts, we will send you together with the tractor for free. 4.During warranty period, free spare parts for quality-problem spare parts replacement. 5.Multi-selection of configuration. Product Model HX454 Wheel Drive 4x4(4x2) Dimension(L*W*H)mm 3350x1500x1860 Weight(KG) 1380 Front Wheel Tread(mm) 850,960,1000,1100,1200,1300 adjustable R Wheet Tread(mm) 960-1300 unlimited adjustable Wheet Base(mm) 1750 Minimum Land Clearance(mm) 330(340) Gear Shifts 8F+2R Tyre Size 9.5--24/650--16(9.5-24/550-16)

We are produce and export Various Rubber Parts like as Bush Bush-Arm Boots Bush Shock Absorber Engine Mounting Insulator etc. for Hyundai Kia SSangyong Daewoo of Korean Cars Toyota Honda Isuzu Nissan Miusubishi of Japanese Please study high quality of various rubber parts

Fresenius fx8 dialyzer is a part of FX Series dialyzer. Its a single use dialyzer. Fx8 Dialyzer are based on optimized and redefine handling. There are several high end technologies have been combined to provide the distinctive functional feature of FX dialyzer. The structure of fibre bundle, membrane ,flow port and housing design provide the performance of the dialyzer along with safety and handling. The optimal membrane permeability design gives minimal loss of blood components. It gives homogeneous blood flow inside the dialyzer.