we are leading manufacturer & exporter of Brass knurling insert.
we are leading manufacture & exporter of Brass washer
we are leading manufacturer of Brass Lock washer
we are leading manufacturer of Brass Elbow .
We are leading manufacturer of Brass Tee.
We Are Leading Manuacturer Of Brass Anchors
We Are Leading Manufacturer Of Brass Male Female Adaptor
We Are Leading Leading Manufacturer Of Brass Precision Tuned Parts
We are leading manufacturer & exporter of Brass Threaded stud
We are leading manufacturer of Brass Parts
We are leading manufacturer of Brass Terminal connector
we are leading manufacturer of Brass stop plug
We are leading manufacture of Brass bush.
We Are Leading Manufacturer Of Brass Guide Bush.
we are leading manufacturer of Brass cable glands
we are leading manufacturer of Brass nut bolts washer
we are leading manufacturer & exporter of standoff/spacers as per requirement or Drawing
We Are Leading Manufacture & Exporter Of Stainless Steel, Brass, Aluminium And Metal Adapter.
We Are Leading Manufacture And Exporter Of Brass, MS Steel And Metal Industrial Components As Per Customer Specification, Design, Drawing Or Requirements.
DATA SHEET FOR EPOXY EPOXY COATING :- INTRODUCTION - EPOXY COATING (HYB) is a two part high solids solvent free epoxy phenolic resin based coating system designed for hard wearing, smooth surface finish for floors, walls and on steel structures. Nonskid surface finish can be achieved on floor, if required. FEATURES: 1) Hard Wearing 2) Non Dusting 3) Excellent Surface Finish 4) Non Smelling 5) Good Aesthetics 6) Highly Chemical Resistant APPLICATION: 1.Stir well before mixing Part A and Part B and mix in the prescribed ratio. 2.Apply one coat of EPOXY primer on the clean and dry surface. 3.EPOXY COATING (HYB) should be applied on the surface by brush or roller within 24 hrs. After application of primer coat it should be allowed to air dry for min. 4 hrs. Preferable in a dust free atmosphere. 4.Apply min. 2 coats with the intercoat interval of 6-8 hrs. PRODUCT SPECIFICATIONS: Application - Brush, Roller Mixing Ratio - As Directed on Packing Port Life - 30 Mins. Drying Time - Touch Dry- 30 Min, Hard Dry 6 Hrs. - Intercoat Interval 6-8 Hrs. Min. - Dry Film Thickness 125-150 Microns/per coat - depending on porosity Covering Capacity - 6-8 sq.met/kg per coat depending on porosity, roughness & method of application. Color Shades - All Standard Shades RECOMMENDED USES: 1) Food & Pharmaceutical 2) Work Shop 3) Clean Room Application 4) Chemical Resistant Coating for Concrete& Steel 5) Petrochemical, Fertilizer plants METHOD OF APPLICATION: SURFACE PREPARATION The long-term durability of the applied Epoxy coating (HYB) epoxy coating is dependent on the adhesion between sub-base and coating material. It is most important therefore, that the substrate surfaces are correctly prepared prior to application. 1.Before application of the Epoxy coating (HYB) surface should be free from loose partials, rust, oils, grease or earlier coatings and should be totally dry. 2.New concrete or cementations surface should be placed at least 28 days and have a moisture content of less than 5% before application of Epoxy coating (HYB) 3.After surface is dry, all repair work like sealing of joints, cracks filling of cavities and crevices should be carried out. HEALTH & SAFETY - Keep the containers tightly closed when not in use. Avoid contact with skin & eyes. It comes in contact with the body, wash affected parts with plenty of water and contact a doctor. Other known sector for Epoxy floor lining, Epoxy garage floor lining, Concrete epoxy lining, Concrete floor epoxy lining, Epoxy pipe lining, Marine epoxy lining, Sub marine epoxy lining, Basement lining epoxy floor shield, Louisiana, Oregon, Chip lining color epoxy floor, Aviation lining epoxy interior.
