Gvpp Series Vertical Polypropylene Pump Suppliers and Manufacturers

Type ZJ and ZJLR pumps are vertical,centrifugal slurry pumps submerged in sumps to work.They are designed for delivering abrasive,large particle and high slurries.These pumps have no need of any shaft seal and sealing water.they can also be operated normally for insufficiend suction duties. Wet parts of Type ZJL pump are made of abrasion-resistant metal. All parts of type ZJLR pump immersed in liquid are lined with rubber our liners.They are suited to transport non-edge angle abrasive slurry. Different size wooden case

This pump is design in vertical type seal less Glandless pump with m

Vertical Submersible Pumps with extended shaft directly goes into sump or tank mainly used for solvents with motor above the ground and the whole pumps below mounting plate inside the tank. Available in Metallic as well as Non-Metallic MOC.

These vertical pumps are designed to operate with the pumping elements immersed in the product. These pumps are compact and space saving. They are custom designed and are manufactured for varying column length to suite the pump depth. The suction port of all the pump sizes are designed so that a strainer can be attached to prevent and large solids entering the pump. These pumps are available in only close coupled configuration. A variety of material of construction, shaft sealing options are also available. Single Stage Pump Capacities upto 500 m3/hr Pressures upto 12 bar These vertical pumps are designed to operate with the pumping elements immersed in the product. These pumps are compact and space saving. They are custom designed and manufactured for varying column lengths to suite the sump depth. Vertical-Single-Stage Multi Stage Pump Capacities upto 500 m3/hr Pressures upto 12 bar These vertical pumps are designed to operate with the pumping elements immersed in the product. These pumps are compact and space saving. They are custom designed and manufactured for varying column lengths to suite the sump depth. Material Options WETTABLE HOUSING COMPONENTS: Fabricated Steel Fabricated Stainless Steel. STATOR: Natural Nitrile High Nitrile EPDM Chloro-Sulphonated Rubber Fluoroelastomer Aflas HNBR. ROTOR: Tool Steel Case Hardened Steel Alloy Steel Stainless Steel. COUPLING ROD: Alloy Steel Stainless Steel. SHAFT: Alloy Steel Stainless Steel. OTHER EXOTIC MATERIALS: Duplex Super Duplex Alloy 20 Haste alloy. ROTOR SURFACE COATINGS: Ceramic Coatings Tungsten Carbide Hard Chrome Plating. PROTECTIVE COATINGS: Rubber Lining Epoxy Coatings. Price Range: Rs.25000 to Rs. 50 Lacs* * Minimum prices are mentioned for smallest model Bare Shaft Pump. Prices may vary for complete Pump set with motor & accessories and for exotic material options or customized pumps.

Roto s Vertical Twin Screw Pumps are available in both external & internal bearing configuration. Pumps with steam jackteing as an option is also available. The suction & discharge ports are in a line. Mechanical seals are standard. Option for gland packing is also available. Pumps are fitted with relief valves suitable for 100% bypass. Vertical Internal / External Bearing RV series Capacities upto 500 m3/hr Pressures upto 40 bar These pumps are designed to suit the areas where space is a constraint. They are available in internal as well as external bearing configurations. These pumps can handle fluids with high temperatures upto 3500C / 6600F with or without steam jacketing, electrical/steam tracing arrangement as an option. API 682 type seals can be mounted. Built in safety relief valve designed for 100% bypass. MOC CASING: Cast Iron, Cast Steel, Fabricated Steel Fabricated Stainless Steel. LINER: Case Steel, Stainless Steel. SCREWS: Alloy Steel Stainless Steel, Hardened Steel. TIMING GEARS: Hardened Steel. OTHER EXOTIC MATERIALS: Duplex Super Duplex . SCREW SURFACE COATING: Hard Chrome Plating. Price Range: Rs. 1.25 Lacs to Rs. 50 Lacs* * Minimum prices are mentioned for smallest model Bare Shaft Pump. Prices may vary for complete Pump set with motor & accessories and for exotic material options or customized pumps.

Product Description The TS/TSR heavy duty cantilever sump pump is designed for applications requiring greater reliability and durability than conventional vertical process pump can offer. The heavy duty cantilever design makes the TS/TSR pump ideally suited for heavy continuous handling of abrasive and corrosive liquids and slurries whilst submerged in sumps or pits. Fully elastomer lined or hard metal fitted. No submerged bearings or packing. High capacity double suction design. Optional recessed impeller and suction agitator available. · TS pump - hard metal construction · TSR pump - rubber covered construction Structure: Fully Cantilevered – Eliminates submerged bearings, packing, lip seals, and mechanical seals that other vertical slurry pumps typically require. Impellers – Unique double suction impellers; fluid flow enters the top as well as the bottom. This design eliminates shaft seals and reduces thrust load on the bearings. Large Particle – Large particle impellers are also available and enable passing unusually large solids. Bearing Assembly – The maintenance friendly bearing assembly has heavy duty roller bearings, robust housings, and a massive shaft. Casing – The metal pumps have a heavy walled abrasive resistant 27% chrome alloy casing. Rubber pumps have a molded rubber casing adhered to sturdy metal structures. Column and Discharge Pipe – The metal pump columns and discharge pipes are steel, and the rubber columns and discharge pipes are rubber covered. Upper Strainers – Snap in elastomer strainers fit in column openings to prevent overly large particles and unwanted refuse from entering casing of the pump. Lower Strainers – Bolt-on cast strainers on the metal pump and molded snap-on elastomer strainers on the rubber pumps protect the pump from oversize particles. Specification 300T-TS Vertical Pump Capacity (Q) : 288-1267m³/h Head (H) : 6-33m Power (KW) : 200KW Speed(N) : 350-700r Effiency : 50 Impeller Dia.: 610mm Impeller No.: 5 Outlet Dia.: 300mm Weight: 3940kg Slurry Pump Spares Pumps spare and parts material : High chrome alloy:A33, A05, A07, A49, etc. vertical slurry pump Natural rubber: R08, R26, R33, R55, etc. Other material as per requests, like stainless steel, duplex stainless steel, Nickle alloy, Alloy 20, and so on. Applications Mining Coal washery Power plant Metallurgy Petrochemical Building material Dredging Other industrial departments, etc. This series of pumps are preferred by many customers with special installation requirements and widely applied in pool. Its wear-resistant metal liner could handle abrasive slurries with rough particles and high concentration.

Type vs and vsr pumps are vertical, centrifugal slurry pumps submerged in sump to work. They are designed for delivering abrasive, large particle and high density slurries. These pumps have no need of any shaft seal and sealing water. They can also be operated normally for insufficient suction duties. Wet parts of type vs pump are made of abrasion-resistant metal. All parts of type vsr pump immersed in liquid are lined with rubber outer liner. They are suited to transport non-edge angle abrasive slurry. The type with¡°l¡±is a sump pump of extension shaft series, which is suited for the working condition of deeper level. The guide bearing construction is added to the pump on the basis of the standard pump, so the pump is with both more steady operation and wider application range, but flushing water should be attached to the guide bearing.

Technological parameters: Flow rate: 10~ 2000 l/h. Pressure: 0~1.0 mpa. Adjustment mode: manual, electric, pneumatic, frequency conversation. Measuring accuracy: 1%. Motor power: 380v / 0.75kw (or 1.5kw) / 50hz (for your reference only) Fluid temperature: -45~450 Allowed particle size: 0.01 mm Viscosity of fluid: 0.3~800 cst Head of pump: 1 Diaphragm: 1 Material: Worm wheel: tin bronze Worm: 40cr or 38crmoal Diaphragm: ptfe Pump head: pvc, cs, ss, ptfe, etc. Inlet & outlet part: pvc, cs, ss, ptfe, etc. Bearing: nsk japan, skf sweden Oil seal: nok japan Advantage: 1. Simple structure and beautiful appearance. 2. Vertical installation of motor avoid the leakage of lubrication oil and prevent the environmental pollution. 3. Patented integrated sleeve adjustable eccentric transmission mechanism. 4. High drive efficiency. 5. Strong carrying capacity with accurate flow rate. 6. The flow rate is adjustable with capability of 0-100% free adjustment. 7. Stable and reliable operation with low noise. 8. Convenient maintenance and long life service. Certificate: Dnv iso9001:2000 Iso14001-2004 Ohsas18001 Ce Api Application: Our products are widely applied to petroleum, natural gas, chemical, power industry, environmental water treatment, nuclear industry, pharmaceutical, foodstuff, etc. We occupy an important market position in petroleum, natural gas, polycrystalline silicon, fluorine chemical, our market occupancy reaches more than 90% in chinese fluorine chemical industry. Strong wooden box with pallet

Head - Up,to,65,mtr Max Flow Rate Up,to,300,m3,/,hr Model - GXP,Series Temp - Max,80,dig,C MOC - PP,UHMWPE RPM - 1440-2900 Type - Mechanical,Steel/Gland,Type In order to keep pace with never ending demands of the customers, our company is instrumental in offering GXP Polypropylene Pump. Application: Water Treatment Plant, Effluent Treatment Plant, Transfer And Loading I Unkaing like HcL Sulphuric Add, Caustic Liquid Scrubbing Of Corrosive Gasses like Nh3, Cot, Sot, 1.2, F2, &2 Etc. Eller Press For Oyes & Chemicals. Circtiation Of Chemicals In Metal Finishing Industry.

Introduction: FP series enhanced polypropylene centrifugal pump, FS series engineering centrifugal pump and FPZ anti-corrosion self priming centrifugal pump are new modified plastic pumps which are developed on the basis of absorbing domestic and international advanced technology of the same product.They all adopt mechanical seal. FP series polypropylene centrifugal pump uses CFR-PP (enhanced polyprolene) as the material of the pump body,and FS series engineering plastic centrigfugal pump use ABS(engineering plastic) as the material of the pump body. FPZ anti-corrosion self priming centrifugal pump is of one mould shaped uses material of polyvinylidenefluoride (PVDF) and enhanced polypropylene (RPP). Main Character: Advanced structure,light weight,small volume,long life. They are widely used to transporrt acid ,alkali ,hydrochloric acid etc corrosion liquid in chemical industry, foodstuff,pharmacy,electroplate,papermaking,environment protection,water treatment etc. Operating coditions: 1.Plastic pump should be installed flatly forbid supporting weight of pipeline.If it needs particularly be installed vertically,the motor must be upturned. 2.Pump needs to pour water before it starts. When pumped liquid surface is higher than axesline, open suction pipe valve before it starts. If pumped liquid surface is lower than axes line,the pipeline needs to match bottom valve. 3.Check if the rotary direction of motor and pump is accordant. 4.Medium temperature: FP centrifugal pump=80°C FS centrifugal pump =60°C. FPZ self priming centrifugal pump =120°C 5.Pump forbid racing and operation.

Applications : Domestic , Gardens, Irrigation, Hotels, Appartments, Agriculture And Sprinkler Irrigation Structural Characteristics Pump Casting : Grey Iron Casting Impeller : Ci / Gun Metal Shaft/motor Body : Ss 410/ss 302 Thrust Bearing : Bronze/stainless Steel/carbon MAXIMUM OPERATING CONDITIONS Pumping Medium " Clean Water Free From Solids, Chemically And Mechanically Non- Aggresive Liquid Temperature :

APPLICATIONS : Domestic , Gardens, Irrigation, Hotels, Appartments, Agriculture and Sprinkler Irrigation Structural Characteristics Pump Casting : Grey Iron Casting Impeller : Ci/gun Metal Shaft/motor Body : Ss 410/ss 302 Thrust Bearing : Bronze/stainless Steel/carbon Maximum Operating Conditions Pumping Medium : Clean Water Free From Solids, Chemically And Mechanically Non- Aggresive Liquid Temperature :

Vertical pump SEP series Motor Model:SEP-Vertical pump Materical:PP Power:5hp Pole:2P Rubber:EPDM Frequency:50HZ Caliber:2"X1.5" Max.capacity:466l/min Max.head:20.5m Weight:31.0kg

Vertical pump SEP series Motor Model:SEP-Vertical pump Materical:PP Power:2hp Pole:2P Rubber:EPDM Frequency:50HZ Caliber:2"X1.5" Max.capacity:350l/min Max.head:14.0m Weight:21.0kg

Vertical pump SEB series Motor Model:SEB-Vertical pump Materical:PP Power:2hp Pole:2P Rubber:EPDM Frequency:50HZ Caliber:2"X3" Max.capacity:350l/min Max.head:13.8m Weight:30.0kg

Vertical pump SEB series Motor Model:SEB-Vertical pump Materical:PP Power:15hp Pole:2P Rubber:EPDM Frequency:50HZ Caliber:4"X4" Max.capacity:1750l/min Max.head:29.0m Weight:118.0kg