We make customized rolling, sliding gates, collapsible gates for home, commercial building factories etc. These gates come in Aluminum, Stainless Steel or in Steel. The surface is powder coated to last many years after installation. These gates can be installed on tracks or without tracks. Every aspect of the gates can be customized. These gates are easy to operate with minimal effort. Our standard dimensions Height 1600mm (height can customized) Stretching ratio: 1:0.17 + 0.42 (can be customized) Gate Minimum length :2 Meters Gate Maximum length: upto 90 meters ( double Gates) Operation: Hand operated, Motorized. Colors available: Blue, Red (colors can be customized) Please contact us for competitive pricing.
We supply Film Faced Plywood ( Shuttering Plywood) with Original Dynea film red brown, brown film (40/128 grade), 30kg, densified Film Faced (15mm to 12mm),11 ply, 12mm thickness (+/- .5mm), 10-15times repetition, 72Hours WBP Glue (Phenol Formaldehyde). Hot press-40minute heating and cooling cycle. Rubber wood + Poly core: 30Kg: Rubber wood + Full core: 30Kg: Eucalyptus + Full core: 38Kg: Benefits: more usages, more load bearing, less scaffolding, save on labor cost. Origin: India, China
Three phase motor Range 0.10 h.P. To 75 h.P. (0.075 k.W. To 55 k.W.) frame 63 to 250m in 2, 4, 6, 8, 10 & 12 pole Mounting - foot- flange- face Standards Performance conforms to be: 325 and dimensions according to is 1231 & is 2223 Frame Motor are supplied in a robust, rugged cast iron frame with integral feet. On request we can supply motor in aluminum body up to 100 l frame. Ratings All standard three phase motors are continuous rated to comply with performance standards. Voltage and frequency Supply volts 415 +- 5% 3 phase 50 hz. +- 3% (on customer request we are also able supply motor in 220, 380, 460, 525 volts on hz. 50 or 60 also) Enclosures Motor ip-44 protection as defined in is: 4691. Motors can be supplied with ip-54 and ip-55 on request. Insulation Motor supply with class b & f insulation as standard feature. Also supply h on request of customer. Shaft Made from high carbon steel to provide exceptional strength & rigidity to minimize deflection. Rotor Rotors are of high-pressure e.C. Grad aluminum die-cast. Every rotor is dynamically balanced. Its make motor low amplitudes of vibration & noise Bearings & lubrication Bearings are adequately lubricated with lithium based high temp up to 150 deg. All the motors are supplied with c3 ball bearing & fully charged with lithium base grease at the time of assembly. Earthling terminals Motor provided with minimum two earthling terminals. One in the terminal box and other on foot. Paints All standard motor are painted with semi glossy synthetic enamel paint. However sp. Paint is available on request. Export packing avalbale
1.We use imported base paper from Germany. For solid color, base paper most 80 to 120GSM. For wood base paper is between 70-85 gsm 2. High quality water-base ink- Available over 200 shades in Solid colors and wood grains 3. With clear texture ,high Fidelity meeting international standards. 4. With smooth surface coating 5. Germproof, mould proof, antistatic and wear-resistance. 6. Green environmental protection and Odorlessness which Conforms to the GB18584-2001 standard requirement 7. Can be used for the hot press molding craft, the production efficiency is high. 8. Melamine paper takes shape easily, is widely used for the panel furniture and the decorative yarn. Product Specification: Width: 1230-1260mm or 1300-1800mm Length: 500-1000m For storing: Put it in room to a cool and dry place keep the temperature 20-25°C in room. The best humidity is: 50-60% We can also give you complete decorative solution with Matching Melamine Edge Banding, PU Paper. If you need just need Melamine/prelaminated boards either in MDF / Particle board we can also do so
Specifications 1.odorless 2.low VOC 3.antimicrobial 4. mildew resistant 5.environmentally friendly 6.waterproof 7.Scrub resistance Description It is an enhanced mildew proof product adopting nano-scale Ag+ antimicrobial and mildew proof technology, integrating odorless formula, with fresh product smell, smooth paint film, durable and beautiful paint.As an affordable and environmentally friendly product with excellent decorative performance, it is characterized by fresh smell, environmental health, strong covering power, large painting area, convenient constructionapplication, short constructionapplication period, etc. Specification Data Solvent: Water Pigment: Non-lead pigment Theoretical Solids By Volume: more than 50% Theoretical Coverage: Theoretically 1 litre of this product covers 12 sqm in 1 coat Coverage varies considerably depending on application methods and surface roughness and porosity. Shelf Life: Minimum 12 months at 77F(25C) unopened and store in cool and dry places. Recommended Film Thickness: Wet: 80 micron Dry: 30 micron Dry Time: At 77F (25C) and 50% R.H. to recoat Touch Dry: 1 hours Recoat : 2-3 hours Application: Brush, Roll, conventional spray or Airless Spray. Thinner: Thin up 15% depend on different application methods & temperature. Do not over thin by adding more than 30% water. Brush or Roller: For sealing new or bare surfaces thin with up to 1 part of clean water to 5-10 parts of paint(10%-20%) Conventional Spray: Add up to 1 part clean water to 5 parts paint(20%) Airless spray: do not thin Clean-up: Clean up equipment with water Typical painting system Substrate System All kinds of Wall surfaces 1.Alkali Resistance Primer (1 coat) 2.Emulsion Wall Paint (2 coats)
Plastic scrap, plastic scrap, ldpe, hdpe, industrial films, post industrial resins, copper electrical motor scrap, insulated copper wire.
Frozen chicken, pork, frozen beef, chicken feet, chicken paws, chicken, sunflower oil, soybean oil, canola oil, red kidney beans, beans, white beans, lentils, chickpeas, chana dal, green mung beans, black eye beans, sesame seeds, soybeans, yellow corn, white sugar, compressor scrap, scrap, used electric motor scrap, copper wire scrap, oranges, fresh fruits, lemons, mandarines, limes, apples, pears, guavas, soda ash, caustic soda, uht milk, milk powder, peanuts, groundnuts, ldpe, hdpe, lldpe, polyvinyl chloride (pvc), polystyrene (ps), polypropylene (pp), polycarbonate (pc), polyphenylene oxide, used cooking oil, used engine oil, virgin granules, used blue drum scrap, recycled granules, bitumen, beef omasum, deer antlers, alfalfa hay.
Non-Sterile Medical Examination Nitrile Gloves Powder free & Latex free 100% Virgin raw materials with FDA certificate & as per ASTM D6319/ CE EN 455 Quality standard: ASTM D6319, with 510K and FDA, CE/EN455, Color: Blue, white Finger Tips: textured Cuff: Beaded Pcs per Box for S/M/L/XL : 100pcs/box Origin: China, Vietnam, Thailand, Malaysia Benefits Protection from unwanted and harmful substances Beaded Cuff ensures easy donning and prevent roll down Superior Strength with better Puncture resistance Finger Tip Textured enhances wet and dry grip Thinner Guage improves tactile senstivity Custom Design enhances comfort and fit Provide an Alternate Solution for individual who are allergic to natural rubber latex Material : Synthetic Nitrile Type : Non-Sterile Powder Free, Amibidextrous, Finger Tip Textured, beaded cuff. Storage: Store in a dry and cool place, the temperature not higher than 38�° C Shelf life: 2 years Physical Properties Tensile Strength: Before Aging 14Mpa min Tensile Strength: After Aging 14Mpa min Elongation at Break (%): Before aging 500% min Elongation at Break (%): After aging 400% min Length: 230 mm in XS, S, M, L, XL Width: 70+/- 10 (XS) Width: 80+/- 10 (S) Width: 95+/- 10 (M) Width: 110+/- 10 (L) Width: 120+/- 10 (XL) Thickness Single wall ( mm): Fingers 0.050mm min Thickness Single wall ( mm): Palm 0.050mm min
Unbalance vibratory motor with special tough design is used as drive for the vibrating machines. The applications are feeding, screening, discharging etc. The vibration motors are available in 2800, 1440, 960 and 750 RPM. The special features includes sturdy frame with stiffing ribs, Body Fabricated with high grade ductile iron, Extra-large dia. Of Shaft to resist bending under high centrifugal force, Fitted with heavy duty cylindrical roller bearing, specially varnished winding with terminal box to withstand tough operating conditions, Specially designed electrical parameters for cool operation condition. Vibration motors are available from 0.25 HP to 10 HP in foot mounted design or flange mounted type. Vibration motor are widely used in process plants, Glass, Food, Metal, Coal power plant, Chemical, Ceramic, Iron and steel, Foundries, Packaging industries etc. Unbalanced vibratory motor in 2,4,6 or 8 pole design motor available in flange or foot mounted. In brief movable unbalance plates can be adjusting on circumference for easy tracing of the weight which serves oscillation width from zero to maximum. Range: 0.25 HP to 10.0 HP Three phase supply and 0.10 HP to 1 HP Single Phase supply Application : Conveying, Compacting, Emptying, Cleaning, Testing & Feeding of all kind of products, process can be achieved with help of vibratory motor. Loosening & separation of bulk material screening, dewatering, filtration, crushing.
AC motors, DC motors, geared motor, gear box, vibratory motor, flame proof motor, bench grinder, polisher, PMDC motor, cooling tower motor.
Chiller, cooling tower, motor, pumps, ductable, vrv & vrf, ahu, fcu, split, window, ducting, insulation, supply fan, exhaust fan, damper, fire fighting, softener plant, lift, escelator, dgset etc..