Find Verified Ca 100Fr Steel Coating Firestop Mortar Suppliers, Manufacturers and Wholesalers

APPLICATION OF SK-HB K-SILICATE MORTAR : * K-SILICATE is used for jointing Acid Resisting brick in construction of vessels in suited for construction of fume chambers and stacks handling hot, dry Acid fumes and vapors. It is also used for jointing chemical resisting stoneware pipes. K-SILICATE cement is good bedding material for Acid â?? Resisting bricks and tiles. The concrete surface needed protection should be dryed, clean and rough. The bricks or tiles will be set with K-SILICATE cement over concrete surface applied with a suitable an impermeable interliner. When Bedding and Jointing Materials are the same. On the treated surface bricks or tiles are bedded to a thickness of about 6 mm and tamp gently with a wooden piece till the paste squeezes out of joints. The paste that is squeezed out of the joint should be removed by trowel with good finishing. After the mortar of the joint is dryed treat the joints with 20% Hydrochloric Acid Solution by means of brush. A.R.lining should be always in contact with Acid and not with water. Concrete subtract like Floor, Wall, tanks and similar surface should be protected with a membrane of Bitrok Mastic or compound steel tanks should be protected with rubber or PVC subjected to chemical conditions and temperature of chemical media. The Brick lining is recommended over the protective layer of Bitrok Mastic. When Bedding and Jointing Materials are Different. Spread the silicate type mortar about 6 to 8 mm thick on the back of the tile or brick. Press the tile on the bed leaving required space for joints between tiles for bricks. After the bedding mortar is set, fill Mp the joints with specified cement.PRODUCT DATA SHEET FOR SK-HB ( K-SILICATE) MORTAR A general purpose cement for acid conditions Resistant to High & medium concentrations of most of the common organic and inorganic acids except Hydroflouric acid. Recommended where the concentration of the acid is high suitable for high temperature. Unsuited to aqueous solutions, alkaline conditions. PREPARATIONS OF MORTAR : * Measure 1 part by weight of K-SILICATE solution into a suitable mixing pan. * Add slowly and gradually 3 parts by weight K-SILICATE mortar and mix thoroughly to form a smooth mortar. * In hot season very large batches of mortar will become stiff quite rapidly therefore small batches, not exceeding 4 to 8 kgs. Will be prepared. * The cement mortar will be used before it starts setting.

* PHOSCAST Phoscast : Phosphate Bonded Castables * PURPOSE customers using FBC boilers (Particularly underbed feed FBC boilers) for the protection of inbed coils against erosion potential by applying highly abrasive resistant refractory on inbed coils above fuel feed system. BACKGROUND * Two of such actions are providing special alloy studs on inbed coils and applying highly abrasive resistant refractory on the outer bottom loops of inbed Coils which are above the fuel feed nozzles. * GANESHAS has taken number of approaches to identify the key factors affecting erosion rates with an objective to enhance the life of inbed tubes as well as implementing the corrective action to reduce the erosion rates. Phosphate coatings are often used to protect steel parts against rusting and other types of corrosion * Erosion of inbed coils in fluid bed combustor is unavoidable phenomenon however the rate of metal wastage and thus the life of tubes depends on various factors like ash & fuel properties, design of Combustor / feeding system, flue gas velocities operating conditions etc. It has been also observed that maximum erosion prone inbed coils are those which come above fuel feed nozzles and an area of approximately 1 to 1.5 mts around fuel feed systems are badly affected. APPLICATION Phoscast-90 XR can be applied by ramming with wooden mallet having adequately large head @" dia x 5" length x 10â?? Jong handle). The desired lining or repair thickness is built up in several courses while ramming the mass to uniform thickness. Phoscast refractory should never be trawled to obtain smooth surface; ramming only should finish surface. Any excess mass is to be sliced off with trowel edge and then finished by ramming again for bed coil. Tube application of AFBC boiler, the material pasty mass should be finger pressed into the studs of the tube with maximum force. Finish should be given by pressing the hand palm against material applied, using surgical type thin rubber hand gloves.

DATA SHEET FOR EPOXY EPOXY COATING :- INTRODUCTION - EPOXY COATING (HYB) is a two part high solids solvent free epoxy phenolic resin based coating system designed for hard wearing, smooth surface finish for floors, walls and on steel structures. Nonskid surface finish can be achieved on floor, if required. FEATURES: 1) Hard Wearing 2) Non Dusting 3) Excellent Surface Finish 4) Non Smelling 5) Good Aesthetics 6) Highly Chemical Resistant APPLICATION: 1.Stir well before mixing Part A and Part B and mix in the prescribed ratio. 2.Apply one coat of EPOXY primer on the clean and dry surface. 3.EPOXY COATING (HYB) should be applied on the surface by brush or roller within 24 hrs. After application of primer coat it should be allowed to air dry for min. 4 hrs. Preferable in a dust free atmosphere. 4.Apply min. 2 coats with the intercoat interval of 6-8 hrs. PRODUCT SPECIFICATIONS: Application - Brush, Roller Mixing Ratio - As Directed on Packing Port Life - 30 Mins. Drying Time - Touch Dry- 30 Min, Hard Dry 6 Hrs. - Intercoat Interval 6-8 Hrs. Min. - Dry Film Thickness 125-150 Microns/per coat - depending on porosity Covering Capacity - 6-8 sq.met/kg per coat depending on porosity, roughness & method of application. Color Shades - All Standard Shades RECOMMENDED USES: 1) Food & Pharmaceutical 2) Work Shop 3) Clean Room Application 4) Chemical Resistant Coating for Concrete& Steel 5) Petrochemical, Fertilizer plants METHOD OF APPLICATION: SURFACE PREPARATION The long-term durability of the applied Epoxy coating (HYB) epoxy coating is dependent on the adhesion between sub-base and coating material. It is most important therefore, that the substrate surfaces are correctly prepared prior to application. 1.Before application of the Epoxy coating (HYB) surface should be free from loose partials, rust, oils, grease or earlier coatings and should be totally dry. 2.New concrete or cementations surface should be placed at least 28 days and have a moisture content of less than 5% before application of Epoxy coating (HYB) 3.After surface is dry, all repair work like sealing of joints, cracks filling of cavities and crevices should be carried out. HEALTH & SAFETY - Keep the containers tightly closed when not in use. Avoid contact with skin & eyes. It comes in contact with the body, wash affected parts with plenty of water and contact a doctor. Other known sector for Epoxy floor lining, Epoxy garage floor lining, Concrete epoxy lining, Concrete floor epoxy lining, Epoxy pipe lining, Marine epoxy lining, Sub marine epoxy lining, Basement lining epoxy floor shield, Louisiana, Oregon, Chip lining color epoxy floor, Aviation lining epoxy interior.

The Ground Granulated Blast Furnace Slag (GGBS/GGBFS) is a type of eco-friendly green building material and high quality secondary cementitious material for concrete and cement. It is recognized as one of the best secondary cementations material for building high durable concrete stricture in the world today! GGBS has taken over a top place of high-performance cement and concrete mineral additives with its unique characteristics of hydration, low-price raw material. GGBS is obtained by quenching molten iron blast furnace slag (a by-product of iron and steel making) in water or steam. It is then further grounded into the desired fineness in terms of the required particle size distribution. The main components of blast furnace slag are CaO (30-50%), SiO2 (28-38%), Al2O3 (8-24%), and MgO (1-18%). The other important aspect of GGBS is its superiority in concrete durability which extends the lifespan of buildings from fifty years to a hundred years. APPLICATIONS Soil stabilization Mortar Used in combination with Portland cement Pre-cast concrete Ready mix concrete Specialist projects

Product Name 55% Aluzinc/Galvalume Steel Coil Thickness 0.12mm-4.0mm or 0.8mm/1.0mm/1.2mm/1.5mm/2.0mm Width 600mm-1250mm or 914mm/1000mm/1200mm/1219mm/1220mm Content 55% Alu,43.5%Zinc,1.5% Si Surface Light Oil/Oil/Dry/Chromate/Passivated/Anti Finger Zinc Coating AZ30g/m2-AZ275g/m2 Coating PE/PVDF/HDP/SMP Package Details Plastic Cloth/Brown Paper/Galvanized Plate

Thickness 0.13-3.0mm Width Galvanized steel strip 24-600 mm; galvanized steel coil:600-1250mm Coil weight Usually is 3-4.5 tons,the max coil is 10 tons Zn coating 0.13-0.8 mm is 30-150 g/m2; 0.8-1.5 mm is 30-180 g/m2;1.5-6.0 mm is 30-275 g/m2 Coil ID 600-1500 mm,Normal width is 91 4/1000/1219/1250/1500 mm Steel grade DX51D,DX52D,DC01,DC02,SGHC Surface regular/mini/big/zero spangle,skin pass, chromated, unoiled, dry Packaging seaworthy export standard package, or according to the customers requirement

Type:Steel Coil, Hot-Galvanized Steel Sheet, Color Coated Steel Sheet, C Surface Treatment:BA/2B/NO.1/NO.3/NO.4/8K/HL/2D/1D Package:Standard Sea Worthy Package or as customer's requirement Keyword:cold rolled coil Payment:D/P,L/C,TT,D/P,D/A Usage:Architectural decoration, luxury doors, elevators decorating,ect Grade:200 400 series MOQ:25 Tons Special Use:Silicon Steel Surface structure:zero spangle / minimized spangle / regular spangle/ big spang Type:Steel Coil Standard:AiSi Width:1251-1500mm Certificate:API Certificate:ce Certificate:SNI Certificate:SASO Certificate:SABS Surface Treatment:Normal Oiled Hardness:Full Hard Tolerance:�?�±1% Processing Service:Welding Processing Service:Punching Processing Service:Cutting Processing Service:Bending Processing Service:Decoiling Processing Service:Annealed Processing Service:Black Annealed Skin Pass:Yes Oiled or Non-oiled:Slightly Oiled Alloy Or Not:Non-Alloy Delivery Time:within 7 days Place of Origin:CN;JIA Application:High-strength Steel Plate Thickness:0.5mm~3.0mm Length:1000-12000(requirment) Grade:steel

1) Material: stainless steel. 2) Coated with Teflon, Platinum and Chrome. 3) Customized brand and OEM are welcome. 4) Sharpness parameter of the blade is below 15N . Color - Blue Function - Shaving Packaging - Standard export carton

1. Basalt short fiber - a new material to replace steel fiber. Basalt short fiber is an inorganic mineral fiber with a length of less than 50mm, which can be evenly dispersed in cement concrete. 2. Characteristics of basalt short fiber (1) the specific gravity of steel fiber is 7.8 and that of cement concrete is 2.5. After mixing, the specific gravity of steel fiber is higher than that of cement, and the cement will sink and have poor dispersion. The specific gravity of basalt short fiber is 2.6, which is basically equivalent to that of cement concrete. After mixing, it does not sink, has good dispersion, is degradable, and is green. The road surface will not be as hard as steel fiber, resulting in car driving noise.. (2) Basalt staple fiber is a real "multifunctional" fiber. Acid and alkali resistance (especially alkali resistance, fully applicable to cement concrete), low and high temperature resistance, insulation and sound insulation. The tensile strength is three times that of steel fiber. The corrosion resistance of basalt fiber is better than that of steel fiber. The compressive strength is 20% higher than that of steel fiber, which is suitable for harsh environment. It has excellent comprehensive performance. (3) Low cost. The price of basalt fiber used in cement concrete is significantly lower than that of 50% steel fiber. (4) Natural compatibility. Basalt fiber is a typical silicate fiber, which is easy to disperse when mixed with cement concrete and mortar. Fresh basalt fiber concrete has stable volume, good workability and durability, and has excellent high temperature resistance, impermeability, crack resistance and impact resistance.

Produced by Chongqing Hesheng Longgang Technology Co., Ltd. (manufacturer) Basalt fiber reinforcement (new material to replace reinforcement) Product Description: basalt fiber reinforced bar (BFRP) is a new composite material formed by pultrusion process. It is made of basalt fiber as reinforcement, resin, filler and curing agent. Now it has been widely used in construction, highway and bridge constructionã?? Basalt fiber reinforcement can completely replace ordinary steel reinforcement and deformed steel; Compared with ordinary reinforcement, it has strong advantages: (see Annex for technical parameters) 1. The cost is the same as that of ordinary reinforcement; 2. The strength is 200% of the ordinary reinforcement with the same specification and diameter; The tensile strength reaches 1100mpap; The reinforcement is only 450MPa, 3. Basalt fiber reinforcement, especially with high acid, alkali and corrosion resistance, is a kind of electrical insulator that will never rust. 4. Basalt fiber reinforced bar, which is non-magnetic. It has high tolerance to the moisture concentration in cement mortar and the penetration and diffusion of carbon dioxide, and can prevent the corrosion of concrete structure in harsh environment, so as to improve the durability of buildings and bridges. 5. The specific gravity of basalt fiber reinforcement is 2.1g/cm3; The specific gravity of steel and reinforcement is 7.85/cm3; The diameter weight of the same specification is 370% lighter than that of steel reinforcement, and the strength is 200% of that of steel reinforcement. 6. The physical properties of basalt fiber reinforcement are higher than that of steel reinforcement, and the cost is the same as that of steel reinforcement, which is of epoch-making significance to replace steel reinforcementã??

1. Chopped basalt fiber Basalt fiber is a kind of inorganic fiber material. Chopped basalt fiber is an inorganic mineral fiber with a length of less than 50mm and can be evenly dispersed in cement concrete. 2. Characteristics of chopped basalt fibers (1) The naturalness of raw materials. Because the raw material for producing continuous basalt fiber depends on the natural volcanic extrusive rock, there are no ingredients harmful to human health except that it is inherently high in chemical stability and thermal stability. (2) Comprehensive performance. Basalt fiber is acid resistant and alkali resistant. It is both low temperature and high temperature resistant. It is insulated and insulated by heat and electricity. Its tensile strength is higher than that of large tow carbon fiber. Its elongation at break is even better than that of small tow carbon fibers. It has high compressive strength, shear strength and adaptability to aging, and has good comprehensive properties in harsh environment. (3) Low cost. The price of basalt fiber used in cement concrete is significantly lower than that of steel fiber and polyester fiber. (4) Natural compatibility. Basalt fiber is a typical silicate fiber, which is easy to disperse when mixed with asphalt concrete, cement concrete and mortar. The newly mixed basalt fiber concrete has stable volume, good workability and durability, and has superior high temperature resistance, anti-seepage, crack resistance and impact resistance.

Product name : Color Coated 304 Stainless steel sheet Grade : 304 Thickness range : 0.3mm-3.0mm, Width range : 600mm-1500mm Length : 2000mm, 2438mm, 3048mm Size : : 1000mm*2000mm, 1219mm*2438mm, 1219mm*3048mm, or as required Finish : No. 1 , No. 4, hairline , 2b, BA, 8K, embossed, PVD color coated, sand blasted, anti-fingerprint Lead time : 7 to 15 working days after the receipt Packing : Wooden pallet or according to customer's request Application : Interior/exterior/architectural/bathroom decoration, elevator decoration, hotel decoration, kitchen equipment, ceiling, cabinet, kitchen sink, advertising nameplate Warehouse Storage : Shandong Jintuo Metal Materials Co., Ltd is located in Liaocheng City, the capital of steel tubes. It is a large enterprise specializing in the sales of carbon steel, stainless steel, galvanized color coated products, and copper and aluminum.Our company adopts a flexible business approach and management mechanism to provide good services to customers, while also considering the interests of the owner and the project, in order to ensure the quality of the project Packing and shipping : Our products are exported to multiple overseas countries and regions such as Europe, America, South Asia, Southeast Asia, Africa, and Latin America, and have won the trust and support of customers with excellent quality and service. During the supply process, the company can timely use sufficient funds to adjust the production variety and model of the steel plant, ensuring the use needs during the peak construction period.

Decoration field: 304 stainless steel can be used in decoration field. 304 stainless steel has been widely used in the decoration industry due to its high tensile strength, good internal wall finish and excellent wear resistance. Just like our common stainless steel stair guardrails, handrails, stainless steel anti-theft windows, stainless steel doors, stainless steel tables and chairs, they are all made of 304 stainless steel decorative tubes. In life, the bathroom is wet and the kitchen is full of lampblack, so 304 stainless steel can be used in these two places. Industrial field: 304 stainless steel is used in the industrial field, mainly for industrial transmission pipelines and mechanical structural parts such as petroleum, chemical, medical, food, light industry, mechanical instruments, etc. Generally, the working pressure of water supply system in high-rise buildings is high, while the tensile strength of 304 stainless steel is strong, and the possibility of water leakage under external force is very small. It is an important material of water supply system in high-rise buildings Product name Color Coated 304 Stainless steel sheet Grade 304 Thickness range 0.3mm-3.0mm, Width range 600mm-1500mm Length 2000mm, 2438mm, 3048mm Size 1000mm*2000mm, 1219mm*2438mm, 1219mm*3048mm, or as required Finish No. 1 , No. 4, hairline , 2b, BA, 8K, embossed, PVD color coated, sand blasted, anti-fingerprint Lead time 7 to 15 working days after the receipt Packing Wooden pallet or according to customer's request Application Interior/exterior/architectural/bathroom decoration, elevator decoration, hotel decoration, kitchen equipment, ceiling, cabinet, kitchen sink, advertising nameplate

Product name : Color Coated 304 Stainless steel sheet Grade : 304 Thickness range : 0.3mm-3.0mm, Width range : 600mm-1500mm Length : 2000mm, 2438mm, 3048mm Size : 1000mm*2000mm, 1219mm*2438mm, 1219mm*3048mm, or as required Finish : No. 1 , No. 4, hairline , 2b, BA, 8K, embossed, PVD color coated, sand blasted, anti-fingerprint Lead time : 7 to 15 working days after the receipt Packing : Wooden pallet or according to customer's request Applicati on : Interior/exterior/architectural/bathroom decoration, elevator decoration, hotel decoration, kitchen equipment, ceiling, cabinet, kitchen sink, advertising nameplate Warehouse Storage : Shandong Jintuo Metal Materials Co., Ltd is located in Liaocheng City, the capital of steel tubes. It is a large enterprise specializing in the sales of carbon steel, stainless steel, galvanized color coated products, and copper and aluminum.Our company adopts a flexible business approach and management mechanism to provide good services to customers, while also considering the interests of the owner and the project, in order to ensure the quality of the project

Decoration field: 304 stainless steel can be used in decoration field. 304 stainless steel has been widely used in the decoration industry due to its high tensile strength, good internal wall finish and excellent wear resistance. Just like our common stainless steel stair guardrails, handrails, stainless steel anti-theft windows, stainless steel doors, stainless steel tables and chairs, they are all made of 304 stainless steel decorative tubes. In life, the bathroom is wet and the kitchen is full of lampblack, so 304 stainless steel can be used in these two places. Industrial field: 304 stainless steel is used in the industrial field, mainly for industrial transmission pipelines and mechanical structural parts such as petroleum, chemical, medical, food, light industry, mechanical instruments, etc. Generally, the working pressure of water supply system in high-rise buildings is high, while the tensile strength of 304 stainless steel is strong, and the possibility of water leakage under external force is very small. It is an important material of water supply system in high-rise buildings Product name Color Coated 304 Stainless steel sheet Grade 304 Thickness range 0.3mm-3.0mm, Width range 600mm-1500mm Length 2000mm, 2438mm, 3048mm Size 1000mm*2000mm, 1219mm*2438mm, 1219mm*3048mm, or as required Finish No. 1 , No. 4, hairline , 2b, BA, 8K, embossed, PVD color coated, sand blasted, anti-fingerprint Lead time 7 to 15 working days after the receipt Packing Wooden pallet or according to customer's request Application Interior/exterior/architectural/bathroom decoration, elevator decoration, hotel decoration, kitchen equipment, ceiling, cabinet, kitchen sink, advertising nameplate

Product name : Color Coated 304 Stainless steel sheet Grade : 304 Thickness range : 0.3mm-3.0mm, Width range : 600mm-1500mm Length : 2000mm, 2438mm, 3048mm Size : 1000mm*2000mm, 1219mm*2438mm, 1219mm*3048mm, or as required Finish : No. 1 , No. 4, hairline , 2b, BA, 8K, embossed, PVD color coated, sand blasted, anti-fingerprint Lead time : 7 to 15 working days after the receipt Packing : Wooden pallet or according to customer's request Application : Interior/exterior/architectural/bathroom decoration, elevator decoration, hotel decoration, kitchen equipment, ceiling, cabinet, kitchen sink, advertising nameplate Warehouse Storage : Shandong Jintuo Metal Materials Co., Ltd is located in Liaocheng City, the capital of steel tubes. It is a large enterprise specializing in the sales of carbon steel, stainless steel, galvanized color coated products, and copper and aluminum.Our company adopts a flexible business approach and management mechanism to provide good services to customers, while also considering the interests of the owner and the project, in order to ensure the quality of the project

Dolomite mineral is a double carbonate of calcium and magnesium and it exhibits a granular structure. It has high natural whiteness and it's noted for their ease of dispersion. Its use improves properties such as weather ability, reduces shrinkage, fissure development and water absorption. Natural Dolomite Powder is of White Colour and is used as Filler in many applications such as Soap & Detergent, Paints, Ceramics and many other Industries. Applications: - Soap & Detergent Leather Cloth Industry Cable Industries Rigid PVC Pipes Iron, Steel, and Ferro-Alloys Industries Paints, Inks, Powder Coating Ceramic Industry Rubber Industry Glass Industry Available Mesh Size: - 100 TO 700 MESH Custom sizes and Material of required specifications can be made in case of Bulk and Regular orders. BRIGHTNESS: - 92 TO 96 AS PER REQUIREMENT Index Compound Result 1. Silica - (SiO2) 10.41 % 2. Alumina - (AI2O3) 01.15 % 3. Iron - (Fe2O3) 00.21 % 4. Titanium - (TiO2) 00.18 % 5. Calcium - (Cao) 30.02 % 6. Magnesium - (MgO) 18.41 % 7. Soda - (Na2O) 00.34 % 8. Potash - (K2O) 00.07 % 9. Loss on Ignition - (LOI) 38.91 %

Fluorite ore (CaF2) is widely used in industry and beyond. This chemical compound is mostly fit for the production of hydrogen fluoride, which is used for example in glass etching and yeast production. It is also a valuable raw material used in the production filters and optical glasses, anti-reflection coatings, cosmetics, (calcium) nitrogenous fertilisers used in agriculture, dental preparations and varnishes. Fluorite is also a valuable material for the steel manufacturing industries. With our double storage warehouses in Port Harcourt and Lagos we are positioned to supply 1000-3000MT of this product monthly.

Essential details Warranty: 3 years After-sale Service: Online technical support, Other Weight: 20kg/bag Chemical Composition: Steel Wire Alloy Or Not: Is Alloy Secondary Or Not: Non-secondary Project Solution Capability: total solution for projects, Others Application: building/office/shopping mall, Concrete Construction Support Design Style: Modern Model Number: Concrete Steel Fiber Product name: fiber concrete Material: Steel Surface treatment: Copper Coated Color: Golden Standard: International standards Length: 13�±1.2mm Package: 25kg/bag L/D Ratio: 50-70 Keyword: Concrete Steel Fiber Supply Ability 5000 Ton/Tons per Month Packaging Details Each 20kgs Net Plastic Woven Flexible Container, packing in wooden case 1.08tons on pallet. Each 20gp' can load 21.6 tons Good quality wholesale copper coated micro steel fiber concrete fiber reinforced concrete Product Specification. Straight Copper Coated Steel Fiber Material Steel Wire Diameter 0.55mm Length 10-15mm L/D ratio 42-50 TS More Than 2850 Mpa Package 25kg/bag,1.25T/Bulk Bag