Airlife Respiratory Therapy Solution Suppliers and Manufacturers

APPLICATION OF SK-HB K-SILICATE MORTAR : * K-SILICATE is used for jointing Acid Resisting brick in construction of vessels in suited for construction of fume chambers and stacks handling hot, dry Acid fumes and vapors. It is also used for jointing chemical resisting stoneware pipes. K-SILICATE cement is good bedding material for Acid â?? Resisting bricks and tiles. The concrete surface needed protection should be dryed, clean and rough. The bricks or tiles will be set with K-SILICATE cement over concrete surface applied with a suitable an impermeable interliner. When Bedding and Jointing Materials are the same. On the treated surface bricks or tiles are bedded to a thickness of about 6 mm and tamp gently with a wooden piece till the paste squeezes out of joints. The paste that is squeezed out of the joint should be removed by trowel with good finishing. After the mortar of the joint is dryed treat the joints with 20% Hydrochloric Acid Solution by means of brush. A.R.lining should be always in contact with Acid and not with water. Concrete subtract like Floor, Wall, tanks and similar surface should be protected with a membrane of Bitrok Mastic or compound steel tanks should be protected with rubber or PVC subjected to chemical conditions and temperature of chemical media. The Brick lining is recommended over the protective layer of Bitrok Mastic. When Bedding and Jointing Materials are Different. Spread the silicate type mortar about 6 to 8 mm thick on the back of the tile or brick. Press the tile on the bed leaving required space for joints between tiles for bricks. After the bedding mortar is set, fill Mp the joints with specified cement.PRODUCT DATA SHEET FOR SK-HB ( K-SILICATE) MORTAR A general purpose cement for acid conditions Resistant to High & medium concentrations of most of the common organic and inorganic acids except Hydroflouric acid. Recommended where the concentration of the acid is high suitable for high temperature. Unsuited to aqueous solutions, alkaline conditions. PREPARATIONS OF MORTAR : * Measure 1 part by weight of K-SILICATE solution into a suitable mixing pan. * Add slowly and gradually 3 parts by weight K-SILICATE mortar and mix thoroughly to form a smooth mortar. * In hot season very large batches of mortar will become stiff quite rapidly therefore small batches, not exceeding 4 to 8 kgs. Will be prepared. * The cement mortar will be used before it starts setting.

Unilever Pond's Face Care Variants: Acne Solution Face Foam, Age Miracle Day Cream, Miracle Night Cream, Clear Solution Face Scrub, Men Energy , Men Acne Solution, Oil Control, Pure White, Day Cream for Normal Skin, Day Cream for Oily Skin, Skin Perfecting Cream, Sun Dullness Face Cream Scrub, Tone Up FM+FF, Tone Up Milk Cream, White Beauty Face Foam.

Inspection item Appearance White Granular Available chlorine Wt. % 60%MIN PH value (1% water solution) 5.5-7.0 Moisture (%) 5%MAX Granularity (mesh) 20-60mesh

Appearance White granular, good fluidity Active Oxygen(O) 13.5% Iron(Fe)(%) 0.0015 % Moisture 2.0% Bulk Density g/l 700-1100 PH value (3%water solution 20) 10~~11

Checking Item Test Standard Sodium oxide(Na2O)% 28.00-30.00 Silica(SiO2)% 27.00-29.00 Water insoluble% 0.2 Fe(ppm) 200ppm Whiteness% 80 Bulk Density 0.80-0.97g/cc PH of 1.0% Solution 12-13 Melting Point 72.2 ParticularSize % (16-30mesh) 90 98

High-speed copper plating of welding wire is brown brown liquid, which is used for non electrodeposition of high-speed copper plating film on iron to facilitate wire drawing process. It can make copper ions deposit orderly, make copper deposit compact, and have strong adhesion. At the same time, the complexing agent can also effectively complexe excessive iron ions in the tank solution, so that the tank solution remains stable. The deposition film is golden yellow and pink, which is loved by users. It can be used as immersion or continuous production line. The weight of copper film is 5-20g/m2

Calcium thiosulfate solution CAS NO .: 10124-41-1 Molecular formula: Ca2S2O3 Molecular weight: 152.208 Physical and chemical properties: colorless transparent liquid, non-dangerous goods Use: used in medicine, agriculture and other fields Packing:1240kg IBC drum Product specifications: Appearance Clear transparent liquid Content Ca2S2O3 % 24% S 12.4 Lead ppm 1 Mercury ppm 1 Iron ppm 0.01 pHï¼ 20 6.5-9.0

Commodity: Sodium Lauryl Ether Sulfate Synonyms: Sodium Laury Ethyle Sulfate 70% aqueous solution; Sodium Alkyl Ethoxy Sulfate 70% aqueous solution; Sodium C10-16 Alkyl Ethoxy Sulphate (Predominantly C12-C14) 70% aqueous solution; SLES 70% aqueous solution Molecular formula: CH3-(CH2) n-(O-CH2-CH2) p -OSO3Na, where n=9~15, p=2 Mean molecular weight: 388 Description: It has excellent detergency, emulsification ,and foamability, it is easy to dissolve in water. As well as favorable hard-water resistant and high-biodegradation. Specifications: ITEM SLES - 70 SLES - 28 Appearance Transparent or white viscous paste light yellow transparent liquid Odor No strange odors No strange odors Active Matter% 70�±2 28�±2 PH value 7.0-9.5 7.0-9.5 Unsulfated matter% Max. 2.0 Max. 1.0 Sodium sulfate % Max. 1.0 Max. 0.5 Microbiological(CFU/g) Max. 100 Max. 100 Dioxane(ppm) Max. 50 Max. 50 Heavy metal(ppm) Max. 10 Max. 10 Peroxide% Max. 0.1 Max. 0.1 Color Max. 10 Max. 10 Usage: 1. Used to prepare the shampoo, bath foam, soap,hand cleaner , liquid detergent and detergent. 2. Used in hard surface cleaner, such as the glass cleaner, car cleaner, they always used with the K12ã??LAS-Naã??6501. 3.Used in the textile, paper making, leather, machinery, petroleum. Industry. Packing: plastic drum, per 160kg/170kg/200kg/220kg net weight Loading weight in 1x20fcl: 18.24mt for 160kg drum 19.38mt for 170kg drum 17.6mt for 220kg drum Storage: sealed and stored at the room temperature, the shelf life is two years.

A practical and nutritious breakfast solution that offer you a complete nutrition and energy (milk, egg, cereal, oats and essential vitamins) for the whole family. Language in Packaging = English, Bahasa Indonesia. Port of Loading: Semarang, Indonesia. Note: We could paste sticker on each pack should there is any additional information needed (importer name, information in other language, etc)

Commodity:Sodium Aluminate Other names:Aluminium sodium dioxide; SodiumaluminatecaHO; dialuminum; oxygen(-2) anion; sodiooxysodium Molecular formula: NaAlO2 CAS No.: 1302-42-7 Property: colorless, odorless, tasteless, strongly alkaline. Solid type: white powder or granules, hygroscopic, readily soluble in water. The aqueous solution may absorb CO2 and form aluminum hydroxide precipitate. Addition of NaOH is required to increase stability. Liquid type: transparent slurry, stable during storage life. Prolonged stay of diluted aqueous solution may cause aluminum hydroxide precipitate. Use: In the construction process, it can be used as leaking stoppage agent combined with the sodium silicate. In paper-making, this product can mix with aluminum sulfate to be a good filling agent. In water treatment, it can be used as additive of purifier. Technical specifications: ModelNa2Al2O4Al2O3Na2O/Al2O3Insoluble % Density, g/c m3Shelf life, month LiquidA-129181.700.51.48±0.0112 A-238241.300.51.50±0.0112 SolidSNA162391.25±0.050.5 24 SNA265411.25±0.050.5 24 SNA377481.25±0.050.5 24 SNA480501.25±0.050.5 24 Packing: Solid powder in 25kg PP bag Liquid in 300kg drums or 1500kg IBC tank

[Technical Indicators] 1. Industrial grade Indicator Name/Indicator Value Powdered Products (F) Needle Products (Z) Level 92 Level 93 Level 95 Level 92 Level 95 Appearance White or light yellow powder, without caking White or yellowish needle-like, without lumps Active matter,% 92.0 93.0 95.0 92.0 95.0 Free oil,% 1.2 1.2 1.2 2.0 1.5 Inorganic salt,% Sodium sulfate 5.8 4.8 2.5 4.8 2.5 Sodium chloride 0.15 0.15 0.15 0.15 0.15 Moisture,% 2.0 2.0 2.0 4.0 3.0 PH value (1% aqueous solution) 7.5-9.5 7.5-10 Whiteness (WB), 90 2. Toothpaste grade Indicator Name/Indicator Value Toothpaste Grade (Y) (I) Level (II) Level (III) Level Appearance White or yellowish powdery or needle-like, without caking Active matter,% 95.0 93.0 93.0 Free oil,% 1.2 1.2 1.2 Inorganic salt,% Sodium sulfate 2.5 3.2 4.0 Sodium chloride 0.15 0.15 0.15 Moisture,% 2.0 2.0 3.0 PH value (1% aqueous solution) 8-9.3 8-9.3 8-10 Whiteness (WB), 90 Foaming capacity/mm 180 Heavy metal (as Pb)/ (mg/Kg), 15 Arsenic content (as As)/ (mg/Kg), 3 Total bacterial count/ (CFU/G), 100 Total number of molds and yeasts/ (CFU/G), 100 Fecal coliforms/G Not to be detected Pseudomonas aeruginosa/G Not to be detected Staphylococcus aureus/G Not to be detected   3. Latex grade Indicator Name/Indicator Value Latex grade (powder, needle, liquid) Aggregate grade Seed level Liquid K12 Appearance White or yellowish powdery or needle-like, without caking Light yellow transparent liquid Active matter,% 94.0 92 28.5-30.5 Free oil,% 0.8-1.0 1.5-2.0 1.5 Inorganic salt,% Sodium sulfate 3.0 3.0 1.5 Sodium chloride 0.15 0.15 0.05 Moisture,% 3.5 3.5 - PH value (1% aqueous solution) 8-10 7.5-9.5 Whiteness (WB), 90 - Color Klett (30% active), - 60 4. Reagent grade Indicator Name/Indicator Value Reagent grade Level 99% Level 97% Appearance White flaky crystals White powder Solubility (1%, alcohol) Completely dissolved Solubility (10%, aqueous solution) Completely dissolved Chroma APHA (20%, deionized water), 15   - Active matter (%), â?¥ 99 (on dry basis) 97 Petroleum ether soluble matter (%), 0.2 1.0 Sodium sulfate (%), 0.5 1.5 Sodium chloride (%), Moisture (%), 1.0 2.0 PH value (1% aqueous solution) 6.0-8.0 6.0-11 Phosphate, 1ppm - Lead (Pb), 2ppm Iron (Fe), 1ppm Nitrogen, 5ppm - Arsenic (As), 0.1ppm Fraction content (%), 99.0 Absorbance (3%, deionized water) 230nm 0.4 260nm 0.1 280nm 0.1 - 410nm 0.01

Formula:KAl(SO4)2 12H2O Relative Molecular Weight:474.39 CAS NO,: 7784-24-9 EINECS No.:5637-689-7 HS CODE.: 2833301000 Appearance: lump, white crystal, white powder Properties:Colorless, transparent, particle or crystalline powder, odorless, nontoxic, tastes slightly sweet and puckery, astringent, easily soluble in water, its water solution appears acid,is would lose crystal water and become white powder on heating Usage; Food industry: Buffering agents and leavening agents in food-grade products. Chemical Industry: Water Flocculant, aluminum tanning agents and after-treating agents for leather tanning in the leather industry, dyeing agents,Astringents,mordants etc. Items Specifications Potassium aluminum sulfate [AlK(SO4)2.12H2O] % 99.5 Plumbum(Pb) mg/kg 5.0 Arsenic (As) mg/kg 2.0 Fluorine (F) mg/kg 30.0 Selenium (Se) mg/kg 30.0 Moisture % 4.0

Commodity : Soda Ash Light / Dense Molecular formula:na2co3 Molecule weight:105.99 H.S Code:28362000 Cas: 497-19-8 Properties : white crystal powder, easily soluble in water, water solution is alkali. Easily absorbing moisture and co2 if exposing in the air. Applications: mainly used in glass-manufacturing, chemical industry, metallurgy, paper, dye, synthetic washes and petrochemistry. Packing :25kg/ 40kg/50kg/750kg pp woven bag with waterproof pe inner , two layers Specifications standard : gb210.1-2004 Items : specification First grade : specification Second grade Total alkalinity(as na2co3 in dry base) %99.2% min98.8% min Chloride content(as nacl) %0.7% max0.9% max Iron content(as fe in dry base) /%0.003% max0.0035% max Sulphate content(as so4 in dry base) /%0.03% max0.03% max Water insoluble matter /%0.03% max0.03% max Loss on ignition a/ %0.5% max0.5% max

Commodity:Sodium persulfate Molecular Formula : Na2S2O8 Molecular weight : 238.13 Description Sodium persulfate is a white,crystalline,odourless salt.It is used as initiator for the Polymerization of monomers and as a strong oxidizing agent in many applications.It has the particular advantage of being almost non - hygroscopic,of having a particularly good storage stability as a result of its extremely high purity and of being easy and safe to handle. Transportation Road/Rail transport : GGVS,GGVE,ADR,RID/CLASS 5.1 Sea transport : GGV Sea/IMDG code : CLASS 5.1 Page 5185,UN no.1505 Water hazards class 1(slight water hazard) All information is given in good faith,but without warranty,since the conditions of use are outside our control. Verification by the user is recommended.Freedom from patent restriction cannot be assumed. Package (1) In 25kgs net multiple paper bags with one PE bag inner (2) In 25kgs net PE bags (3) In 25kgs net woven bags with two PE bags inner (4) In 1000kgs net big woven bags with one PE bag inner The above package is also with a pallet 1000kgs each. Storage NPS(SPS) is not combustible but assists combustion materials due to release of oxygen.Provided it is stored under appropriate condition.It must be stored dry in closed containers and protected from direct sunlight,heat and humidity.Impurities such as dirt,rust or traces of metal and reductants may cause catalytic decomposition.The product as supplied or in solution needs to be handled with appropriate care.The eye,skin and clothes must be protected when working with NPS(SPS) as damp powder or aqueous solution has a bleaching and slightly corroding effect. Application Polymerization : Initiator for the emulsion or solution Polymerization of acrylic monomers,vinyl acetate,vinyl chloride etc.and for the emulsion co-polymerization of styrene,acrylonitrile,butadiene etc. Metal treatment : Treatment of metal surfaces(e.g. in the manufacture of semiconductors; cleaning and etching of printed circuits),activation of copper and aluminium surfaces. Cosmetics : Essential component of bleaching formulations. Paper : modification of starch,repulping of wet - strength paper. Textile : Desizing agent and bleach activator - particularly for cold bleaching.(i.e.bleaching of Jeans). Others : - Chemical synthesis - Water treatment(decontamination) - Waste gas treatment,oxidative degradation of harmful substances(e.g.Hg) - Disinfectant ITEMS SPECIFICATIONS Appearance white crystalline salt Assay 99.0% w/w min Active oxygen 6.65% w/w min Chloride and chlorate(as CL) 0.005% w/w max Ammonia (NH4) 0.05% w/w max Manganese(Mn) 0.0001% w/w max Iron(Fe) 0.001% w/w max Heavy metals(as Pb) 0.001% w/w max Moisture 0.05% w/w max Decomposition of the product as supplied at above 65C Recommended storage temperature Normal Temperature Storage stability as from date of delivery 12 months

English name: Calcium Nitrite Molecular formula: Ca(NO2)2 Molecular weight: 132 CAS NO. 13780-06-8 HS CODE: 28341000 UN NO.: 2627 5.1 type oxidizing agent Properties: White powder without crystal water. It is tasteless and toxic. Easily in water and presents light yellow solution. Specifications: Item Superior grade First grade Second grade Calcium Nitrite[Ca(NO2)2 as dry basis]% 94 92 90 Calcium Nitrate[Ca(NO3)2 as dry basis]%

Trichloroisocyanuric acid (TCCA) 90% Min intro: 1. Molecular formula: C3N3O3C13 Molecular Weight: 232.44 CAS: 87-90-1 HS NO:29336922 UN NO:2468 2. Structural formula: 3. Uses: 1) water treatment: it can be used to disinfect drink water and water in swimming pool, algae-removing in circulating water. 2) Disinfection: It can be used in disinfecting dinner, food, and dishes, or used in the prophylactic disinfection of home, hotel and public place; hygiene and disease control of hospital; or used in the disinfection of silk worm, animals, birds and fish 3) Other: It can be used in anti-shrinkage finishing of wool, textile bleaching, antimoth of paper and chlorinated agent of rubber. 4. Technical Index: Appearance: white powder/granular Available chlorine: 90%Min PH (1% Aq. Solution): 2.7-3.3 Moisture: 0.5% Max Granular Size: 8-30mesh or 20-60mesh Package: 25kg/50kg plastic drum, 50kg fiber drum. 5. Product: According to the requirements of production from customers.

Commodity: Calcium chloride Molecular formula CaCl2 H.S code 28272000 Product feature Calcium chloride is an inorganic salt, which exists as solid or liquid. Solid calcium chloride is a white, crystal substance in the form of flake, granule, pellet or powder. With different crystallized water contents, it can be dihydrate or anhydrous. Liquid calcium chloride is a colorless, clear solution. As calcium chloride has such properties as quick dissolving, exothermic ability, attracting moisture from the air and surroundings, dissolving at very low temperature, Specifications: Analysis Item Standard Calcium chloride (CaCl2) 74%min,77% min,94%min Total Chlorinated Alkali: (NaCl) 5.0%max Magnesium Chloride(MgCl2) 0.5%max Insoluble matter in water 0.25%max Calcium Sulfate (CaSO4): 0.2%max Ferric Oxide (Fe2O3) 0.025%max Heavy Metal as Cu., Pb., Cd., Cr., Hg., As 0.005%max Application Mainly used in drying, melting snow for airport express and street, concrete desiccant and concreting fast, removing dust and oil industry. Exporting Packing :Plastic woven bag with PE ,25kg/50kg/1000kgs net weight or 25kg x 40 bags into one big bag or 40 bags on a pallet with shrink-wrapped Means of transportation :in containers or by bulk vessel with large quantity

Commodity: Sodium Bisulfite Molecular Formula: NaHSO3 Molecular Weight: 104.06 Properties: White monoclinic crystalline powder with sulfur dioxide odor; relative density: 1.49; very easily soluble in water; can be decomposed when heated; slightly soluble in ethanol; aqueous solution is acidic; has strong reducing property; can be oxidized in the air or loose sulfur dioxide. Quality Standard: HG/T3492-80 Technical Indicator High-purity grade Acrylic grade Food grade Refined grade Industrial grade 1 NaHSO3 % 99.5 Insol. in water % 0.003, 0.005, 0.03, 0.04, 0.05 Chloride(Cl) % 0.003, 0.004 Iron(Fe) % 0.001 0.002 0.005 Heavy metal(Pb) 0.001 Arsenic(As) % 0.0001 Clarity test Qualified Use: It is used in the bleaching of cotton textiles; as reducing agent in dyes, paper-making, leather, chemical synthesis; in the manufacture of pharmaceutical intermediates, developer, food bleacher, antiseptic and anti-oxidants. Packing: In PP woven bag lined with PE bag; paper-plastic composite bag, and kraft paper bag etc. Net wt.: 25/50/1000 kgs/bag or upon clients' request.

Commodity: Sodium bicarbonate Synonym: Baking Soda; Bicarbonate of soda; Sodium acid carbonate; Monosodium carbonate; Sodium hydrogen International CHEMTREC , carbonate; Carbonic acid monosodium salt Molecular formula:NaHCO3 Molecule Weight:84.01 H.S code:28363000 CAS:144-55-8 Characteristics: White powder or tiny crystalls, nodorousand salty, easily soluble in water,insoluble in alcohol, presenting slightly alkalinity, decomposed when heating. Decomposed slowly when exposed to moist air. Quality Standard Item The National Standard The Total Alkalinity Content(NaHCO3)% 99.0, 100.5 Loss on Dring% 0.20 PH Value(10g/1) Solution, 8.6 Arsentic Content% 0.0001 Heavy Metal Content, 0.0005 Ammonium Salt pass Clearness pass Uses: food fermentation, feed addive, detergent ingredient, carbon dioxide foamer, pharmacy, leather, ore milling and metallurgy, detergent for wool, extinguisher and metal heat-treating, fiber and rubber industry, etc. Packing:25kgs or 50kgs plastic woven bags lined with one layer polythene bag. (We can meet with all your demands according with your need.)