100Kw To 100Mw Diesel Containerized Power Plant Suppliers and Manufacturers

Fly Ash: Fly Ash is by product generated during combustion of coal, and comprises the fine particles that rise with the flue gases. Ash which is collected from the bottom is termed bottom ash. Fly ash is collected by electrostatic precipitators or other particle filtration equipment before the flue gases reach the chimneys of coal-fired power plants and together with bottom ash removed from the bottom of the furnace is in this case jointly known as coal ash. Depending upon the type of coal being used, the specification of Fly Ash varies considerably, but Fly Ash contains substantial amounts of silicon dioxide and calcium oxide (CaO), both being endemic ingredients in many coal-bearing rock strata. We are a reputed Fly Ash Exporter based in India and are supplying Fly Ash different cement, ready mix concrete, steel, refractories and construction industries. The Major Utilization Areas Of Fly Ash : - Manufacture of Portland Pozzolanic Cement & Performance improver in Ordinary Portland cement (OPC). - Part replacement of OPC in cement concrete. - High volume Fly Ash concrete. - Roller Compacted Concrete used for dam & pavement construction. - Manufacture of ash bricks and other building products. - Construction of road embankments, structural fills, low lying area development. - As a soil amender in agriculture and wasteland development. Types of Fly Ash: - According to the type of coal used fly is classified into two types. Anthracite and bituminous coal produces Fly Ash classified as class F. Class C Fly Ash is produced by burning lignite or sub-bituminous coal. Class C Fly Ash has self-cementing properties. - Class F and Class C Fly Ash are products of the combustion of coal in large power plants. Fly Ash is collected in electrostatic precipitators or baghouses, and then transferred to large silos for shipment. When needed, Fly Ash is classified by precise particle size requirements, thus assuring a uniform, quality product. - Class F Fly Ash is available in the largest quantities. Class F is generally low in lime, usually under 15 percent, and contains a greater combination of silica, alumina and iron (greater than 70 percent) than Class C Fly Ash. - Class C Fly Ash normally comes from coals which may produce an ash with higher lime content generally more than 15 percent often as high as 30 percent. Elevated CaO may give Class C unique self-hardening characteristics. Minimum Order Quantity : 1 container

During last decade Guar has immerged as an important industrial raw material and Produced by man for thousands of years. India has been the single largest producer and exporter of Guar gum accounting for more than 80 percent of the global output and trade. Guar has now assumed a larger role among the domesticated plants due to its unique functional properties. India Ranks First in the production of guar which is grown in the North Western part of the Country which mainly includes the states of Rajasthan, Gujarat, Haryana and Punjab. Other main countries are Pakistan, U.S.A and Brazil The by-product of Guar Gum industry consisting of the outer seed coat and germ material is called guar meal. The Guar meal after gum Extraction is a potential source of protein and contains about 42% crude protein which is one and a half times more than the level of protein in guar seed. The protein content in guar meal is well comparable with that of oil cakes. It is used as a feed for livestock including poultry. Guar meal contains two deleterious factors i.e. residual guar gum and trypsin inhibitor, Toasting of Guar Gum improves its nutritive value in chicks. Toasted guar Meal can be used in limited quantity i.e. Up to 10% in Poultry diet. However it can replace groundnut cake by almost 100% in animal feeds. Guar Gum (Galactomanan) is a high molecular weight carbohydrate polymer made up of a large number of mannose and galactose unit linked together. The crude Guar Gum is a greyish white powder 90% of which dissolves in water. It is non ionic polysaccharide based on the milled endosperm of the guar bean whose average. Composition is: Hydrocolloid: 23% Fats: 40% Proteins: 34% The most important property of the Guar is its ability to hydrate rapidly in cold water to attain a very high viscosity at relatively low concentrations. Its specific colloidal nature gives the solution an excellent thickening power which is 6 to10 times thicker than that obtained from starch. It is stable over a wide range of PH and it also improves the flow ability and pump ability of the fluid. It is a superior friction loss reducing agent.

ChikMat P2 is a Vegan, Gluten-Free, Plant-based and Non-GMO starch. ChikMat P21 is used as an excellent additive or ingredient for Crispy oil fried vegetarian and non-vegetarian products. ChikMat P2 will provide structure, tenderness & binding power in baking. It even gives excellent crispiness by better even coating and with low oil absorption. It is 100% naturally made which does not have any preservatives and Mono sodium Glutamate (MSG).

ChikMat P2 is a Vegan, Gluten-Free, Plant-based and Non-GMO starch. ChikMat P2 is used as an excellent additive or ingredient for Crispy oil fried vegetarian and non-vegetarian products. ChikMat P2 will provide structure, tenderness & binding power in baking. It even gives excellent crispiness by better even coating and with low oil absorption. It is 100% naturally made which does not have any preservatives and Mono sodium Glutamate (MSG).

ChikMat P1 is a Vegan, Gluten-Free, Plant-based and Non-GMO starch. ChikMat P1 is used as an excellent additive or ingredient for Crispy oil fried vegetarian and non-vegetarian products. ChikMat P1 will provide structure, tenderness & binding power in baking. It even gives excellent crispiness by better even coating and with low oil absorption. It is 100% naturally made which does not have any preservatives and Mono sodium Glutamate (MSG).

We are supplier and exporter of TMT Rebars. TMT Bars / Rebar which find usage in the core infrastructure development like construction of Multi Storeyed buildings, bridges, dams, railways, power plants as reinforcement material. These bars are rolled from Tested billets as per IS 2830 which ensures uniform physical and mechanical properties. The range varies from 8mm to 32mm, conforming to BIS 1786 - Fe 415 and Fe 500. Properties Units IS : 1786 Fe 415 OUR BARS IS: 1786 Fe 500 OUR BARS

ChikMat P1 is a Vegan, Gluten-Free, Plant-based and Non-GMO starch. ChikMat P1 is used as an excellent additive or ingredient for Crispy oil fried vegetarian and non-vegetarian products. ChikMat P1 will provide structure, tenderness & binding power in baking. It even gives excellent crispiness by better even coating and with low oil absorption. It is 100% naturally made which does not have any preservatives and Mono sodium Glutamate (MSG). APPLICATION: GLUTEN FREE ALTERNATIVE FOR FLOUR AND BAKERY: ChikMat P1 can make a suitable gluten-free alternative for flour in baking recipes like Waffles, Muffins, Gluten free flour mixes. ChikMat P1 attract and hold more water and helps to increase the moisture content in baked goods and provides structure, tenderness & binding power in baking. FRYING FOODS: ChikMat P1 could serve as a suitable fried food coating where the coating is light and crisp. It helps to lock the flavour of the product while frying. It can improve the texture of the coat foods, such as chicken, fish, or vegetables, before frying and reduces the absorption of oil. The product such as oil fried Nuggets, Potato Shots, and Cheese bites. Even it can be used in Premixes- 65 Masala, Instant Crispy Fry Mix, Manchurian Mix, Bonda Mix, etc... ChikMat P1 coating can give the foods a golden and crispy outer layer during the frying process. PROCEDURE: Replace 5-20 % of Corn flour with ChikMat P1 then add at the time of blending while adding other raw materials FEATURES AND BENEFITS Increase special appearance to the fried products. Better dispersion of spices and other ingredients. Improves texture. Enhance flavor. Low oil absorption. Excellent crispiness. Better even coating

ChikMat P1 is a Vegan, Gluten-Free, Plant-based and Non-GMO starch. ChikMat P1 is used as an excellent additive or ingredient for Crispy oil fried vegetarian and non-vegetarian products. ChikMat P1 will provide structure, tenderness & binding power in baking. It even gives excellent crispiness by better even coating and with low oil absorption. It is 100% naturally made which does not have any preservatives and Mono sodium Glutamate (MSG). APPLICATION: GLUTEN FREE ALTERNATIVE FOR FLOUR AND BAKERY: ChikMat P1 can make a suitable gluten-free alternative for flour in baking recipes like Waffles, Muffins, Gluten free flour mixes. ChikMat P1 attract and hold more water and helps to increase the moisture content in baked goods and provides structure, tenderness & binding power in baking. FRYING FOODS: ChikMat P1 could serve as a suitable fried food coating where the coating is light and crisp. It helps to lock the flavour of the product while frying. It can improve the texture of the coat foods, such as chicken, fish, or vegetables, before frying and reduces the absorption of oil. The product such as oil fried Nuggets, Potato Shots, and Cheese bites. Even it can be used in Premixes- 65 Masala, Instant Crispy Fry Mix, Manchurian Mix, Bonda Mix, etc... ChikMat P1 coating can give the foods a golden and crispy outer layer during the frying process. PROCEDURE: Replace 5-20 % of Corn flour with ChikMat P1 then add at the time of blending while adding other raw materials FEATURES AND BENEFITS Increase special appearance to the fried products. Better dispersion of spices and other ingredients. Improves texture. Enhance flavor. Low oil absorption. Excellent crispiness. Better even coating

This is chemical setting Furan based chemical resistant mortar which is combination of Liquid and Powder, when mixed in proper proportion from workable mortar which after setting and curing give of liquid and give black highly cross linked composites. Furan When set and cured is resistant to highly corrosive acids, alkalis and to powerful organic solvents such as ketones, Aromatic and Chlorinated solvents. It has extreme resistant to Acidic & alkalis, Salts, Greases and Detergents. It resists to Organic & Inorganic acids at their boiling temperature. It is suitable against mild chlorine Gas (dry) phosphorous trichloride, pyridine at room temperature. Furan is especially useful where resistance to mixed media such as aqueous acids /alkalis and organic solvents is needed in chemical plant process and waste streams. Carbon filled Furan is used against corrosive effect of hydrofluoric acid & its salts. PREPARATION OF FURANE MORTAR : Mortar consist of Furan solution and Furan powder. The average mixing ratio necessary to obtain mortar with good working consistency is 1 part by weight Solution & 3 part by weight powder. The ratio will vary slightly depending on temperature and working conditions.Stir the liquid thoroughly before using. Place liquid in a suitable shallow mixing pan. Add powder by weight in the solution mix thoroughly and rapidly until all lumps are dispersed and the mortar is completely homogenous. Spread out the mortar in a thin layer, not more than ¾ thick, to dissipate the heat of reaction and lengthen the working life. Batch size can be varied depending upon the temperature and the speed with which the masons are working. Very large batches will become stiff quite rapidly. Make sure that all the Furan Motrar is used from the pan before another batch is mixed.When working at temperature above 40 C, very small batches not more than 2 Kgs, should be prepared. When working at temperature below 15C the liquid should be kept warm.

Apple washing peeling remove seeds half cutting in-one-machine, also can process pear and other same fruits and vegetables. Parameters : Number of valve openings: determined by the user Production capacity: 45-50 pcs/min, 16 plugs (one circle) Peeling thickness: 1.1-1.3 mm adjustable Suitable fruit diameter: 65-120 mm remove seeds diameter: 22 mm (can be determined according to user requirements) Peel removal rate: 95 % or more . (normal apples, non rotten fruits, dry scars, irregular fruits.) Excluding both ends. Total power of equipment: 2.25 kw Equipment specifications: host; 1800 * 1050 * 2100, auxiliary equipment 3300 * 1200 * 900 Equipment weight : 850 kg Equipment gas consumption: 0.65 m3/min Advanced technology : small area,efficient,sanitary,easy operate and clean,saving labor costs . Apple process machine apple machinery fruit machinery ,pear /apple/round fruits/vegetable peeler, fruit process machine ,apple/pear peeling machinery ,apple /pear seeds remove machine/machinery Canned apple /pear /fruits making machine applesauce making machine applesauce process machinery /equipment, apple ring making machine ,apple production line apple plant ,apple/pear half cutting machinery

Product Description D6 is also be known as Residual Fuel Oil and is of high-viscosity. This particular fuel oil requires preheating to 220 - 260 Degrees Fahrenheit. D6 is mostly used for generators. D6 is a type of residual fuel, mainly used in power plants and larger ships. The fuel requires to be preheated before it can be used. It is not possible to use it in smaller engines or vessels/vehicles where it is not possible to pre-heat it. D6 is its name in the USA. In other parts of the world it has other names Price of product ( USD price or FOB price) : USD 0.65 - 0.70 per Gallons Product origin : Russian Key Specifications/Special Features : International Standard Minimum Order Size and Packaging details : 10000000 Gallons

D6 is also be known as Residual Fuel Oil and is of high-viscosity. This particular fuel oil requires preheating to 220 - 260 Degrees Fahrenheit. D6 is mostly used for generators. D6 is a type of residual fuel, mainly used in power plants and larger ships. The fuel requires to be preheated before it can be used. It is not possible to use it in smaller engines or vessels/vehicles where it is not possible to pre-heat it. D6 is its name in the USA. In other parts of the world it has other names. Residual means the material remaining after the more valuable cuts of crude oil have boiled off. The residue may contain various undesirable impurities including 2 percent water and one-half percent mineral soil. D6 fuel is also known as residual fuel oil (RFO), by the Navy specification of Bunker C, or by the Pacific Specification of PS-400 Recent changes in fuel quality regulation now require further refining of the D6 in order to remove the sulfur, which leads to a higher cost. Despite this recent change, D6 is still less useful because of its viscosity as well as that it needs to be pre-heated before it can be used and contains high amounts of pollutants, such as sulfur. Since it requires pre-heating, it cannot be used in small ships or boats or cars. However large ships and power plants can use the residual fuel oil. The price of D6 diesel traditionally rises during colder months as demand for heating oil rises, which is refined in much the same way.In many parts of the United States and throughout the United Kingdom and Australia, d6 diesel may be priced higher than petrol. D6 Diesel Standards and ClassificationCCAI and CII are two indexes which describe the ignition quality of residual fuel oil, and CCAI is especially often calculated for marine fuels.

Petroalliance diesel fuel is the second distillate of crude oil. Ultra-low sulfur grades of D2, such as GOST 305-82, with a reduce sulfur content to a maximum of 0.02 percent and reduce sulfur pollution emissions. Diesel fuel is often used in diesel engines. Diesel engines or compression ignition engines, rely on the temperature increase of compression, rather than on spark plugs, to achieve reliable ignition timing and combustion efficiency. As a result of their inherently higher compression ratio for a given power output, diesel engines are more fuel efficient than spark ignition engines. Compared with spark ignition automotive engines, diesel engines weigh more, generate more vibration and produce greater particulate or soot emissions. Diesel engines can also produce a particularly carcinogenic type of hydrocarbon pollutant known as polycyclic aromatic hydrocarbons (PAHs), which are generated during the diesel combustion process. The cetane index is a measure of the autoignition quality of a diesel fuel, with higher numbers meaning that the engine is easier to start in cold weather. Our products are exported to Asia, Europe, America, and the CIS

PETROALLIANCE diesel fuel is the second distillate of crude oil. Ultra-low sulfur grades of D2, such as GOST 305-82, with a reduce sulfur content to a maximum of 0.02 percent and reduce sulfur pollution emissions. Diesel fuel is often used in diesel engines. Diesel engines or compression ignition engines, rely on the temperature increase of compression, rather than on spark plugs, to achieve reliable ignition timing and combustion efficiency. As a result of their inherently higher compression ratio for a given power output, diesel engines are more fuel efficient than spark ignition engines. Compared with spark ignition automotive engines, diesel engines weigh more, generate more vibration and produce greater particulate or soot emissions. Diesel engines can also produce a particularly carcinogenic type of hydrocarbon pollutant known as polycyclic aromatic hydrocarbons (PAHs), which are generated during the diesel combustion process. The cetane index is a measure of the autoignition quality of a diesel fuel, with higher numbers meaning that the engine is easier to start in cold weather. Our products are exported to Asia, Europe, America, and the CIS.

PETROALLIANCE diesel fuel is the second distillate of crude oil. Ultra-low sulfur grades of D2, such as GOST 305-82, with a reduce sulfur content to a maximum of 0.02 percent and reduce sulfur pollution emissions. Diesel fuel is often used in diesel engines. Diesel engines or compression ignition engines, rely on the temperature increase of compression, rather than on spark plugs, to achieve reliable ignition timing and combustion efficiency. As a result of their inherently higher compression ratio for a given power output, diesel engines are more fuel efficient than spark ignition engines. Compared with spark ignition automotive engines, diesel engines weigh more, generate more vibration and produce greater particulate or soot emissions. Diesel engines can also produce a particularly carcinogenic type of hydrocarbon pollutant known as polycyclic aromatic hydrocarbons (PAHs), which are generated during the diesel combustion process. The cetane index is a measure of the autoignition quality of a diesel fuel, with higher numbers meaning that the engine is easier to start in cold weather. Our products are exported to Asia, Europe, America, and the CIS.

Petroalliance diesel fuel is the second distillate of crude oil. Ultra-low sulfur grades of D2, such as GOST 305-82, with a reduce sulfur content to a maximum of 0.02 percent and reduce sulfur pollution emissions. Diesel fuel is often used in diesel engines. Diesel engines or compression ignition engines, rely on the temperature increase of compression, rather than on spark plugs, to achieve reliable ignition timing and combustion efficiency. As a result of their inherently higher compression ratio for a given power output, diesel engines are more fuel efficient than spark ignition engines. Compared with spark ignition automotive engines, diesel engines weigh more, generate more vibration and produce greater particulate or soot emissions. Diesel engines can also produce a particularly carcinogenic type of hydrocarbon pollutant known as polycyclic aromatic hydrocarbons (PAHs), which are generated during the diesel combustion process. The cetane index is a measure of the autoignition quality of a diesel fuel, with higher numbers meaning that the engine is easier to start in cold weather. Our products are exported to Asia, Europe, America, and the CIS