Display type: mono stn lcd Display color:16 shades of blue Display size: 5.7¡± (diagonal); display area is 117.2 x 88.4mm Number of pixels :320x240; number of 8x8 characters displayable is 40x30. Input power: 24vdc15% ; less than 20w Ram :512 k bytes Cpu :32 bits risc Battery backed memory:512 k bytes Com1 9-pin female connector: rs232/rs485 Com2 25-pin female connector: rs232/rs422/rs485 Multi-functional port 26-pin connector to: printer or 64 external keys Ethernet:yes External dimensions (mm) 195(w) x 145(h) x 59.1(d) Cut-out dimensions (mm) 185.8 x 135.8 Weight 0.81 kg
Specification: Construction: plastic molding housing Display:7inch 65536 color tft lcd Cpu and core logic:32 bit risc 400mhz processor Dram:64 mb ddr2 on broard Storage:128mb flash memeory on board I/o: 3 serial ports:com1:rs-232/rs-485 2w/4w Com2:rs-232 Com3:rs-232/rs-485 2w 1 usb 1.1 host 1 usd 2/0 high speed device Rtc:built-in Dimension(w*h*d):200*146*42.5mm Dimension(w*h*d):200*146*42.5mm Weight:1-2 kg
Display type:tft lcd. Display color:64k colors. Display size. 10.4¡±. Active area of display:213.2 x 160.4 mm. Weight:3-5kg
PTC thermistors current protector, also called PTC thermistor resettable fuses, protect load against over-current, overload, short circuit. No need for replacement, resume protective function after a short cooling-down time. Ceramic PTC (positive temperature coefficient) thermistors are used instead of conventional fuses to protect load, such as motors, transformers, or electronic circuit, against overcurrent for circuit protection. PTC thermistor protector not only respond to inadmissibly high currents but also if a preset temperature limit is exceeded. PTC thermistor over-current protector limits the power dissipation of the whole circuit by increasing their resistance and thus reducing the current to a harmless residual value. In contrast to conventional fuses, PTC thermistor resettable fuses do not have to be replaced after elimination of the fault but resume their protective function immediately after a short cooling-down time. PTC Thermistor Over-current Protector Application It applies in the over-current overload and short circuit protection of transformers, battery charger, switches, switch power supply, adaptor, meter, instrumentation, apparatus, electronic coils, control panels, air conditioner, automotive electron, etc. Operating Principle of PTC Thermistor for Overload Over-current Protection The operating principle is as indicated in the following. When a circuit is in the normal status, the current through PTC is lower than the rated current and PTC thermistor protector is in the normal state with small resistance value, which will not affect the normal operation of the protected circuit. In case of some fault in the circuit and the current is greater than the rated current, the PTC thermistor protector will become hot quickly and present a high resistance state, which sets the circuit relatively "off" to protect the circuit from damage. After the fault is removed, PTC thermistor protector will automatically restore its low resistance state and the circuit will resume normal operation. Normally, when PTC thermistor is used as an overcurrent protection component, it is preferred to select maximum operating current, maximum operating voltage and proper specifications. Furthermore such factors should be taken into consideration as the dimensions of the components, rated zero-power resistance, operating temperature range, etc.
Linear PTC Thermistor (LPTC) resistance increases with the temperature rises in linearity, displays a virtually linear positive temperature coefficient over their entire temperature range, suitable in measurement and control system, temperature compensation. As the construction material is mainly semiconductor monocrystalline silicon, also called silicon temperature sensor, silicon thermistor, sometimes referred to as silistors. As the temperature coefficient is positive, the silicon temperature sensors exhibit fail-safe operation when a system overheats. Furthermore silicon is inherently stable, so silicon temperature sensor are extremely reliable and have very long operational lifetimes. Hermetically sealed glass package, axial leaded, 2 leads, can operate in high temperature and moisture environment. Linear PTC thermistor in small dimension, tightness, convenient for automatic installation. AMWEI Linear PTC Thermistor (LPTC) Features: 1. Silicon temperature sensors have a TK (temperature coefficinet) which is nearly constant over the complete temperature range. Temperature coefficient a25/50>=0.7%/C. 2. Excellent long term stability, annual diversification rate
Power ntc thermistor description Power ntc thermistor can be a cost effective device to limit the amount of inrush current in a switching power supply or other devices when the power is first turned on. Power ntc thermistor limits surge current by functioning as a power resistor which drops from a high cold resistance to a low hot resistance when heated by the current flowing through it. Inrush-current limiters power ntc thermistor protect circuits from undesirably high currents, suppressing high inrush current surges, while its resistance remains negligible low during continuous operation. Thanks to their low resistance in the operating state, power thermistor have a considerably lower power dissipation than the fixed resistors frequently used for this application. Inrush current limiting power ntc thermistor application Limiting surge current, suitable for the protection of switch mode power supply, ups power, transformers, motors, various electric heating utensil, energy saving lights, ballast, various power circuit, amplifiers, colored displayer, monitors, color tv, filament protection, etc. Power thermistor components can also be used for the soft starting of motors, for example in vacuum cleaners with continuous currents of up to 20 a. Inrush current limiting power ntc thermistor advantages Low cost solid state device for inrush current supression. Minimise line current distortion and radio noise. Protect switches, rectifier diodes and smoothing capacitors against premature failures. Prevent fuse from blowing in error. Inrush current limiting power ntc thermistor features Resin coated disk thermistor with uninsulated lead-wires. Suitable for both ac and dc circuits up to a voltage of 265 v(rms). Wide range of resistance, current and dimension. Excellent mechanical strength. Suitable for pcb mounting.
Temperature sensor and thermowell . Each nos
Model: TBT-10H industrial thermometer is main suitable for lab , Boil water, and liquid object industrial Function: 1. With lcd display temperature; 2. Temperature range: -50c to 300c 3. Measuring accuracy: +/-1c to +/-2c 4. Specification: with a diameter of 48*49mm, tube length of 75/120/200mm 5. Battery: 1.5v;AG13, 1PCS 6. Material: abs+ stainless steel; 7. Color: black 8. CE certification 9. Packing: blister Packing: blister Size: 51.6*28.2*35.5cm Qty: 72pcs Gw: 5kg Nw: 3.7kg
More than 30m communicating distance in room. Ot protocol It is widely used for temperature control on domestic appliance such as air-condition, wall hung boiler(combine boiler), etc. Weekly programmable time zone Energy saving/cost saving 6 programmable time zone per day Winter/summer mode 6 different programs to satisfy different requirements Rf wireless connection,no wire needs to connect to the room thermostat 2 programmable modes.
Thermostat Detailed screw type bimetal thermostat description 1:auto reset 2:cremis shell 3.6.3*0.8 terminal 4:CQC UL VDE TUV SGS Detailed brass screw bimetal thermostat description fixation of the working temperaturing reliable snap action perdurable less radio interference Technical parameters: Electrical parameters: 1)CQC,VDE,UL,CUL AC250V 50~60Hz 5A/10A/15A (Resistance load) 2)UL AC125V 50Hz 15A (Resistance load) 2.Action temperature range: 45~160 (Optional); temperature accuracy: 3.Recovery and action temperature difference: 8~100 (Optional) 4.Connection method: Insert the terminal 250# (bending angle: 0~90deg optional); Insert the terminal 187# (bending angle: 0~90deg optional; thickness: 0.5, 0.8mm optional) 5.Lifespan: over100,000 times 6.Electrical strength: No spark or breakdown for 1min at AC 50Hz 1800V 7.Contact resistance: less than 50m 8.Insulation resistance: less than100M Junction method: Constant-closed: the contact point disconnects when temperature rises; and contact point connects when temperature falls; Constant-opened: the contact point connects when temperature rises; and contact point disconnects when temperature falls. 10.Casing protective class: IP00 11.Grounding method: Connection is made between the metal casing of the temperature controller and the metal part of the grounding device. 12.Installation method: installed for KI031 series: general moving ring, mini round moving ring, flat moving ring general aluminum cover with mounting hole, extra length aluminum cover with mounting hole Structure and application: KI-32 serial products are the temperature controllers taking bimetallic strip as the temperature-sensing unit. In case of normal operation the electrical appliance, the bimetallic strip is in a free state; the contact point is in a state of close/open. When the temperature reaches the action temperature, the bimetallic strip performs quick action generates caused by internal stress due to heating; open/close the contact point; disconnect/connect the circuit; thus, the temperature is in control. When the electrical appliance is cooled to the recovery temperature, the contact point automatically opens/closes to recover normal operation state. Widely used in electrical heating appliances like water dispenser, water heater, sandwich bread baker, dishwasher, dryer, sterilizing cupboard, micro-wave oven, electric heating coffee pot, electric cooker, refrigeratory, air-conditioner, laminator, heater of auto seat. Characteristics: Stable performance, high accuracy, small size, lightweight, high reliability, long lifespan, less interference to radio Precautions: 1.When adopting contact temperature sensing installation, the surface of the metal cover is required to be securely contacted with the installing surface of the controlled device. For ensuring the temperature sensing effect, it is required to coat thermal conductive grease or other similar thermal conductive medium on the surface of temperature sensor. 2.For reliable performance, collapse, loose or distorted top part of the cover is prohibited during installation. 3.Liquid inleakage into the controller, crackle in the casing and unauthorized change of external terminal position are prohibited. 4.When the product is used in the circuit with maximum current of 5A, the cable with copper core at section 0. 5-1mm2 is required for connection; When the product is used in the circuit with maximum current of 10A, the cable with copper core at section 0.75-1.5 mm2 is required for connection; 5.The product should be kept in a clean, dry and corrosive gas-free warehouse with good ventilation and at relative humidity below 90%, environment temperature below 40. Passed certifications :CQC UL VDE TUV SGS. according to customers' requirements.
Detailed Product Description Stable performance, high accuracy, small size, lightweight, high reliability, long lifespan, less interference to radio Name:thermostat model:KI-31 Technical parameters: Electrical parameters: 1)CQC,VDE,UL,CUL AC250V 50~60Hz 5A/10A/15A (Resistance load) 2)UL AC125V 50Hz 15A (Resistance load) 2.Action temperature range: 45~160 (Optional); temperature accuracy: 3.Recovery and action temperature difference: 8~100 (Optional) 4.Connection method: Insert the terminal 250# (bending angle: 0~90¡ã optional); Insert the terminal 187# (bending angle: 0~90 optional; thickness: 0.5, 0.8mm optional) 5.Lifespan: 100,000 times 6.Electrical strength: No spark or breakdown for 1min at AC 50Hz 1800V 7.Contact resistance: 50m 8.Insulation resistance: 100m Junction method: Constant-closed: the contact point disconnects when temperature rises; and contact point connects when temperature falls Constant-opened: the contact point connects when temperature rises; and contact point disconnects when temperature falls. 10.Casing protective class: IP00 11.Grounding method: Connection is made between the metal casing of the temperature controller and the metal part of the grounding device. 12.Installation method: installed for KI031 series: general moving ring, mini round moving ring, flat moving ring general aluminum cover with mounting hole, extra length aluminum cover with mounting hole Structure and application: KI-31serial products are the temperature controllers taking bimetallic strip as the temperature-sensing unit. In case of normal operation the electrical appliance, the bimetallic strip is in a free state; the contact point is in a state of close/open. When the temperature reaches the action temperature, the bimetallic strip performs quick action generates caused by internal stress due to heating; open/close the contact point; disconnect/connect the circuit; thus, the temperature is in control. When the electrical appliance is cooled to the recovery temperature, the contact point automatically opens/closes to recover normal operation state. Widely used in electrical heating appliances like water dispenser, water heater, sandwich bread baker, dishwasher, dryer, sterilizing cupboard, micro-wave oven, electric heating coffee pot, electric cooker, refrigeratory, air-conditioner, laminator, heater of auto seat. Characteristics: Stable performance, high accuracy, small size, lightweight, high reliability, long lifespan, less interference to radio Precautions: 1.When adopting contact temperature sensing installation, the surface of the metal cover is required to be securely contacted with the installing surface of the controlled device. For ensuring the temperature sensing effect, it is required to coat thermal conductive grease or other similar thermal conductive medium on the surface of temperature sensor. 2.For reliable performance, collapse, loose or distorted top part of the cover is prohibited during installation. 3.Liquid inleakage into the controller, crackle in the casing and unauthorized change of external terminal position are prohibited. 4.When the product is used in the circuit with maximum current of 5A, the cable with copper core at section 0. 5-1mm2 is required for connection; When the product is used in the circuit with maximum current of 10A, the cable with copper core at section 0.75-1.5 mm2 is required for connection; 5.The product should be kept in a clean, dry and corrosive gas-free warehouse with good ventilation and at relative humidity below 90%, environment temperature below 40. Passed certifications :CQC UL VDE SGS. according to our custom.
Thermostat Detailed screw type bimetal thermostat description 1:auto rest 2:cremis shell 3.6.3*0.8 terminal 4:CQC UL VDE TUV SGS Detailed brass screw bimetal thermostat description fixation of the working temperaturing reliable snap action perdurable less radio interference Technical parameters: Electrical parameters: 1)CQC,VDE,UL,CUL AC250V 50~60Hz 5A/10A/15A (Resistance load) 2)UL AC125V 50Hz 15A (Resistance load) 2.Action temperature range: 45~160 (Optional); temperature accuracy: 3.Recovery and action temperature difference: 8~100 (Optional) 4.Connection method: Insert the terminal 250 bending angle: 0~90deg optional); Insert the terminal 187(bending angle: 0~90deg optional; thickness: 0.5, 0.8mm optional) 5.Lifespan: over100,000 times 6.Electrical strength: No spark or breakdown for 1min at AC 50Hz 1800V 7.Contact resistance: less than 50m 8.Insulation resistance: less than100M Junction method: Constant-closed: the contact point disconnects when temperature rises; and contact point connects when temperature falls Constant-opened: the contact point connects when temperature rises; and contact point disconnects when temperature falls. 10.Casing protective class: IP00 11.Grounding method: Connection is made between the metal casing of the temperature controller and the metal part of the grounding device. 12.Installation method: installed for KI031 series: general moving ring, mini round moving ring, flat moving ring general aluminum cover with mounting hole, extra length aluminum cover with mounting hole Structure and application: KI-32 serial products are the temperature controllers taking bimetallic strip as the temperature-sensing unit. In case of normal operation the electrical appliance, the bimetallic strip is in a free state; the contact point is in a state of close/open. When the temperature reaches the action temperature, the bimetallic strip performs quick action generates caused by internal stress due to heating; open/close the contact point; disconnect/connect the circuit; thus, the temperature is in control. When the electrical appliance is cooled to the recovery temperature, the contact point automatically opens/closes to recover normal operation state. Widely used in electrical heating appliances like water dispenser, water heater, sandwich bread baker, dishwasher, dryer, sterilizing cupboard, micro-wave oven, electric heating coffee pot, electric cooker, refrigeratory, air-conditioner, laminator, heater of auto seat. Characteristics: Stable performance, high accuracy, small size, lightweight, high reliability, long lifespan, less interference to radio Precautions: 1.When adopting contact temperature sensing installation, the surface of the metal cover is required to be securely contacted with the installing surface of the controlled device. For ensuring the temperature sensing effect, it is required to coat thermal conductive grease or other similar thermal conductive medium on the surface of temperature sensor. 2.For reliable performance, collapse, loose or distorted top part of the cover is prohibited during installation. 3.Liquid inleakage into the controller, crackle in the casing and unauthorized change of external terminal position are prohibited. 4.When the product is used in the circuit with maximum current of 5A, the cable with copper core at section 0. 5-1mm2 is required for connection; When the product is used in the circuit with maximum current of 10A, the cable with copper core at section 0.75-1.5 mm2 is required for connection; 5.The product should be kept in a clean, dry and corrosive gas-free warehouse with good ventilation and at relative humidity below 90%, environment temperature below 40. Passed certifications :CQC UL VDE TUV SGS. according to customers' requirements.
The Apollo touch screen room thermostat is mainly applied the Heat pump, Gas Heating, Electric Heating, and so on systems. Features: 24VAC or Battery Powered (2 x AAA) Large Backlit LCD Touch Screen Security Logic inc Key lock & Limit Control 7 day, 5+2 Day or Manual Operation Programmable Fan Logic Heat cool & Heat Pump Logic Single & Multistage Control Remote Sensor Inputs Outside Sensor Inputs Designed and built by Smart Temp Australia Comprehensive 3 year Warranty RTB Specifications: Input Voltage (Hardwired) 20-30 VAC 50/60 Hz Relay Rating 24 VAC @ 1 Amp Max Per Relay Battery Power (2) AAA 1.5 V Operating Temperature 0° C to 55° C Operating Relative Humidity 0-95% (non-condensing) Storage Temperature 0° C to 65° C Size: 125" W x 85" H x 25" D (mm) LCD Display Size 57 W x 99 H (mm) Back Light White LED Short-Cycle Delay Off or 4 minutes Displayed Temperature Resolution 0.1° C Set Point Range Heating 5° C - 49° C Cooling 6° C - 50° C Heating and Cooling Limits Fully adjustable Onboard Sensor NTC type 3 100K Remote NTC type 3 10K Warranty 3 years (RTB).
Thermocouples are manufactured in many different configurations for multitude of applications. Diameters, lengths, sheath material, lead lengths and sensor material are just a few of the variables that go into determining the style of thermocouple when manufactured. The main determining factors of what type thermocouple needs to be used in a application is temperature, environment, response time and accuracy. The junction of the thermocouple can be grounded, ungrounded or exposed. The thermocouple junction may be of many different styles, from tube type to a washer configuration. The lead length may vary depending on the distance of the temperature controller from the thermocouple sensor. The metal that the sensor is constructed of determines the type of thermocouple manufactured.Applications: Plastic injection molding machinery Food processing equipment Engine and turbine exhaust gas Semiconductor processing Heat treating and metals processing Medical equipment Aerospace industries Packaging equipment Test stands Features Thermocouple Wires: Cromel-Alumel, Iron- Constant, Copper-Constant, imported Bright & Oxidized finish, SWG 10 to 36. PT/PTRH 10%, 13% . Thermocouple Extension & Compensating Cables: Fiber glass covered, PVC / PVC. Asbestos / Asbestosis, Teflon/Teflon, Insulated, Teflon/Fg/SS Braided single pair, multi pair, Type K, J, T, R, and PT-100 RTD Cables 2 core, 3 core, 4 core , 6 core, Also Teflon /silicon rubber Teflon/shielded/Teflon etc qualities. Thermocouple M.I. Cables: SS 316, 310 & Inconel 600 quality type K, J, Simplex 1mm,1.5mm, Simplex & Duplex 3mm,6mm, 8mm, also PT-100 RTD Thermocouple M I Cables SS 316 quality. 3mm, 5mm, 6mm 4 core Thermocouple Assemblies: Straight, L Type , Rotating type, Inmelt Bolt type, Pencil type, Washer, Holder with Spring. Rotating Type, Adjustable Types etc. Made out of SS tube 4.8mm, 6mm,supplied with Spring & Brass bayonets Single Slot & Double Slot , 10mm id, 12mm id, 14mm id, etc. Thermocouple Brass Parts: ADAPTORS 1/8 BSP, 1/4 BSP, 1/2 BSP, 3/8 BSP Single Pin, Double pin Bayonets. Carton box and wooden box.
Various types of thermocouple Can be widely supplied as Customer's requirment--good Erosion-resistant, corrosion-resistant 1) Thermocouples specified for food, health, medicine, and light industries 2) Inert-gas-filled thermocouples and thermocouples for temperature measurement on ships 3) Thermocouples with stainless steel terminal box Features: 1) Complete stainless steel structure 2) With npt threaded connection and flange 3) Assorts of lengths and diameters 4) Thermo-wells and assembled integrated transmitters are supplied. Plastic bags and carton box.
PH-099, designed for simultaneous pH and ORP measurements. It also reads temperature, which is continuously displayed on the dual level LCD. It is a waterproof pH, ORP and temperature meter. All pH readings are automatically temperature compensated(ATC). Measurements are highly accurate with a unique stability indicator right on the LCD. The pH electrode, supplied with the meter, is interchangeable and can be easily replaced by the user. Range : mV 0~1999mV pH : 0.00 to 14.00 pH Temperature : 0 to 55 Resolution : mV 1 mV pH : 0.01 pH Temperature : 0.1 Accuracy : mV 5mV pH : 0.1 pH Temperature : 1 Temperature Compensation : 0 to 50 Electrode : replaceable pH electrode (included);fixed ORP sensor Power Supply : 4 x 1.5V(AG13) Environment : 0 to 50 Dimensions : 170 x 40 x 23 mm Weight : 100 g.
Thermocouples are manufactured in many different configurations for multitude of applications. Diameters, lengths, sheath material, lead lengths and sensor material are just a few of the variables that go into determining the style of thermocouple when manufactured. The main determining factors of what type thermocouple needs to be used in a application is temperature, environment, response time and accuracy. The junction of the thermocouple can be grounded, ungrounded or exposed. The thermocouple junction may be of many different styles, from tube type to a washer configuration. The lead length may vary depending on the distance of the temperature controller from the thermocouple sensor. The metal that the sensor is constructed of determines the type of thermocouple manufactured. Applications: Plastic injection molding machinery Food processing equipment Engine and turbine exhaust gas Semiconductor processing Heat treating and metals processing Medical equipment Aerospace industries Packaging equipment Test stands Features: Thermocouple Wires: Cromel-Alumel, Iron- Constant, Copper-Constant, imported Bright & Oxidized finish, SWG 10 to 36. PT/PTRH 10%, 13% . Thermocouple Extension & Compensating Cables: Fiber glass covered, PVC / PVC. Asbestos / Asbestosis, Teflon/Teflon, Insulated, Teflon/Fg/SS Braided single pair, multi pair, Type K, J, T, R, and PT-100 RTD Cables 2 core, 3 core, 4 core , 6 core, Also Teflon /silicon rubber Teflon/shielded/Teflon etc qualities. Thermocouple M.I. Cables: SS 316, 310 & Inconel 600 quality type K, J, Simplex 1mm,1.5mm, Simplex & Duplex 3mm,6mm, 8mm, also PT-100 RTD Thermocouple M I Cables SS 316 quality. 3mm, 5mm, 6mm 4 core Thermocouple Assemblies: Straight, L Type , Rotating type, Inmelt Bolt type, Pencil type, Washer, Holder with Spring. Rotating Type, Adjustable Types etc. Made out of SS tube 4.8mm, 6mm,supplied with Spring & Brass bayonets Single Slot & Double Slot , 10mm id, 12mm id, 14mm id, etc. Thermocouple Brass Parts: ADAPTORS 1/8 BSP, 1/4 BSP, 1/2 BSP, 3/8 BSP Single Pin, Double pin Bayonets. Wooden box/carton.
1. Auto fan Adjust fan speed automatically according to the temperature Differential between set value and room temperature 2. Sleeping mode Adjust the setting temperature automatically according to the Thermal environmental conditions. 3. Shortcut menu Enter into the pre-setting temperature directly 4. Key-lock function To avoid erroneous operations 5. Timer off function To deactivate the thermostat at your pre-setting time 6. Timer on function To activate the thermostat at your pre-setting time 7. On/off key Zero power consumption after switching off 8. Back light(Optional) Display with backlight, stay on for 15seconds 9. LCD display Inclined larger size LCD display for better read out 10. Sensor calibration To ensure accurate temperature measurement 11. Setting min. /max. Allowed temperature 12. Valve indicator 13. Alternate from Cooling/heating by manual 14.18months Guarantee, ISO9001, CE, FCC.
1.Large LCD screen with blue backlight 2.Setting Temperature Range: 16-35º C,Room temperature:0-50º C 3.Wiring box: 86mm*86mm 4.High grade electronic accessory 5.TX-1008 remote controller is optional(Price is differ) 6.Temperature precision:1º C 7.Locked by remote controller is optional 8.Electric parameter: AC220V±10% 50/60Hz.
1.Temperature setpoint:16º C-35º C.room temperature: 0º C-50º C 2.LCD light screen shows the running condition of valve 3.Sleeping function 4.Manual alternate of cool or heat 5.Automatically adjust the wind speed 6.Set output delay time about 0-10 minutes 7.Advanced microcomputer control wafer 8.room temperature control precision 1º C. 9.Shell Material: White ABS flameproof plastic 10.Electric parameter: AC110/220V±10% 50/60Hz 11.Two-line, three-line motorized valve 12.Two-pipe, Four-pipe cooling and heating system.
