Feature: Portable device suited for outdoor usage Black mark paper location sensor Low battery indicator(7.4v, 2000mah) Equipped with lithium battery for 8 hours continuous work Vairous interface communication and interface capabilites Bluetooth with high communication speed Easy paper loading High printing speed , up to 80mm/s. Application : Mobile pos/retail Hospitality Packing citation Deliveries Onboard transportation Field reparts/installation Warehouse/ logistics Utility billing/meter reading Specification: Model ptp-ii Dimension(w x l x h) 79*110*45mm Print method line thermal printer Paper width 58mm Print width 48mm Weight ( g) 235 (not including the paper roll) English, figure, symbol, chinese, graph, curve, icon pre-stored, barcode (code39/ean13/ean8 /codabar/code128/code93/itf), Qr code, pdf417 Dot pitch (resolution) 203dpi/8 dots/mm Interface Irda/raw-ir, wifi, bluetooth, rs232, mini usb Power 2000mah 7.4v rechargeable lithium battery Recharge adapter stand by recharging / ac adapter Self-check without paper /cover open Black mark test supported Paper feeding Easy paper loading Commands Esc/pos compatible with order sets Paper cut By hands Operate setting Temperature -10¡ãc~50¡ãc ; humidity 20%~85% Recharge setting Temperature 5¡ãc~40¡ãc; humidity 20%~85% Storage setting Temperature -20¡ãc~70¡ãc ; humidity 5%~95% Standard accessories Long-term preservable paper, ac adapter, li-ion battery, usb cable, leather coat Optional accessories serial interface cable/ cd 20pcs/carton
PSTN alarm products adopt PSTN (Public Switched Telephone Network) information data transmission mode and voice platform to remote control & alarm. This kind of products could cover the security of family, store and office. PSTN are popular in the world now. So PSTN alarm products could extensive apply to security installation systems in same areas such as family, electric power, transport-ation, petroleum, coal, railroad, government, police station etc. Main Function 8 wireless guarding zones, 4 hardwire guarding zones. Remote monitor the noise of guarding space and query alarmed zone's name through phone. Support 6 user phone numbers, which dialed while host alarming. Support 13 working LED, quick, simple and clear. Support several of ways to set guarding zone: Emergency /Delay/Part. Send alarm data to alarm center system, while alarming. Inside-voice module can alarm and support operate voice directive. Equip 16 pressed-keys on host for self-program. Local arm/disarm with remote controller, the pressed-keys of the host or remote by phone. Self-defined ring times when the host be called. If the telephone line connected with the host be cut off, the host drives the alarm horn immediately. Equip standby rechargeable battery. While alarming, support dialog through phone network. (Option) Track the guarding zone from remote, while alarming. (New function) While alarming, play alert voice (pre-record) warn intruder. (Option)
ZG-D6MW Open Display For Mobile Phone With alarm function, this ZG-D6MW is mainly designed for High-Theft Solutions of open merchandises such as Mobile, mp3/mp4, PDA, GPS, and etc.. Secure & neat displays of these merchandises, interactions between consumers and merchandises are also realized with this product. And thus better promote sales of open merchandises. Technical parameters: 1) With alarm function 2) 13cm (standard) or customize 3) Aluminous stand, with adjustable top holder, Use for Mobile, mp3/mp4, PDA, GPS, and etc.. When the exhibit is separate from the sensor, or the sensor is separate from the stand, or the sensor is cut, or the stand is separate from the table, it will alarm immediately. 4) Retractor (pull box) inside the stand 5) Inbuilt battery type: 3.6V/ER14250 6) Exterior power adapter: DC-6V 7) Maximum battery standby: 1 year 8) Alarm volume: 85-105DB 9) Alarm indication: red LED light twinkling 10) Tamper indication: green LED light twinkling 11) Low battery indication: red LED twinkling with a "beep" given 12) Turn on / off alarm: sound & light indication 13) Alarm switch: Key (standard) (If remote control is required, please make statement before ordering. Thus we can pre-design it for you!) 14) Adhesive base: T-shaped metal mounting base. (If required, please make statement before ordering) 15) Shell material: ABS & aluminous stand. 36 sets per carton.
H41 Insulation Pressboard-made from Arauco Pulp Production Description: 1) Pre-compressed Pressboard, with Quality Standard: IEC60641-3-1:1992/GB/T 19264.3-2003 2) Thickness: 1.0mm, 1.5mm, 2.0mm, 2.5mm, 3.0mm, 4.0mm, 5.0mm, 6.0mm, 7.0mm, 8.0mm 3) Material: 100% unbleached sulfate pulp imported from Canada, Russia. 4) High density, high mechanical strength, high electric strength and low compression index. 5) 4400mm*2200, 6400mm*3200mm and customized size Transformer pressboard Large Size:4400*1600mm,4200*2100mm,4000*2000mm; Medium Size: 2200*1600mm,2200*1470mm,2200*1400mm; Small Size: 2200*1100mm, 2200*1000mm,2000*1000mm. Usage: Mainly used in oil-immersed transformer as insulation material, also used in reactor mutual inductance ware, electric device and etc. H41 Transformer Board Technical Specifications: No Item Unit Specification Standard 1 Thickness mm í_1.6mm í+7.0% >1.6mm-8.0mm í+5.0% 2 Density g/cm3 í_1.6mm 1.00-1.20 >1.6mm-3.0mm 1.00-1.25 >3.0mm-6.0mm 1.15-1.30 >6.0mm-8.0mm 1.20-1.30 3 Tensile strength MD MPa í¦90 CD MPa í¦50 4 Elongation MD % í¦3.0 CD í¦4.0 5 Shrinkage MD % í_1.0 CD í_1.4 TD í_6.0 6 Moisture % 4.0í¬9.0 7 Ash Content % í_1.0 8 Conductivity of Aqueous Extract Ms/m í_10 9 PH of Aqueous Extract / 6.0-9.0 10 Oil Absorbency % í¦9.0 11 Electrical Strength (In Oil) Kv/mm 1.0mm í¦35 1.5mm í¦30 2.0mm í¦30 2.5mm í¦27 ¦3.0mm í¦24 12 Cutting Size Tolerance mm 1.0mm-8.0mm í+10 13 Inclination Tolerance mm 1.0mm-8.0mm í+10 Package:Wrapped with vinyl film for waterproof, weaved material, then core paper packed, and wooden pallets.
Cast resin transformer For the demand of safety for the power distribution equipment, dry type transformers with fire resistant, non-polluting and humidity resistant features are often the right choice. Hsl cast resin transformer will provide the best and safest solution to all kinds of power distribution system application. Features: Hazard-free to the environment Designed for reliability, safety and flexibility, hslí»s medium voltage cast resin transformers are tropicalized, maintenance-free, environmental-friendly, flame-resistant, self-extinguishing, moisture-proof and space optimization and suitable for application to a wide range of industries such as high rise buildings, power plant, airport, hospitals, museum, hotels, all sectors of industry, surface, underground and tunnel railway systems, oilfield, electric grid, mining, etc. Our standard range of cast resin transformers is 30kva up to 2500 kva, however, we are able to design and manufacture special units to suit most applications. The magnetic cores are made of low specific loss high magnetic silicon steel isolated on both sides by a thin inorganic coating (carlyte). The cores are cut at 45 degrees while uniform pressing, stiffness and solidity of the columns assure a low noise emission. The hv windings, coaxial to the column of the core, are obtained using electrolytic aluminum or copper strips insulated in f class, impregnated to a vacuum system with oven-dried in class f, a high level of cementation which provides the coils a very good isolation and mechanical seal. The lv windings are generally made from electrolytic aluminum or copper foils having class f inter-turn pre-impregnated film insulated and then oven dried. Hsl is an iso9001:2000 compliance manufacturer. Our transformers will be 3-phase, 50hz in frequency, naturally cooled and are manufactured equivalent of iec726 standards. Subject to capacity Packed in wooden crates
Model: HM-DA660 Automatic case maker Mainly features and function: Malfunction and parameters setting aoto-display; auto finishing coverpaper gluing, caseboards positioning,caseflaps bending& pasting, and calendaring; auto lubricating system; timing for glue pre-heating; Screen indicating of adjustment;Glue circulating pump; Hysraulic shock absorption swing-arm boards positioning system; paperboards-platform fine adjusting; coverpapers-platform fine adjusting; coverpaper-platform auto-positioning & revising; back strip auto conveying& cutting; Adopting famous brand bearings like Japanese THK balls bearings; Adopting Panasonic PLC,operable colorful screen and transducer; adopting low voltage control systems in famous brands like SCHNEIDER, OMRON, SMC,SIMENS; body safty shield; Twice bookcase making; removeable texitle-sheets feeders; feeders of excessive coversheets; accepting wrong format of paperboards devices; coverpaper-angles cutter; case-angles round-cutter Open case Max size: 660x405mm Open case Min size: 150x110mm Gutter Width :4-12mm Flaps bending width : 10-15mm Textile sheet coated case open width :150-660mm Textile sheet coated case open height :110-380mm Boards thickness:1-4mm Sponge matted boards thickness:1-6mm Back strip thickness : 0.3-1mm Back strip width :7-80mm Production capacity :10-40pcs/min. Power:11.5kw Dimension:3500 x 3500 x 1900mm Weight : 4200kg Wooden case
PLC Photo-eye auto-height sensing pallet height Separate top ,bottom & up-down Wrap Counter Selector Overwrap time is set to create an overwrap Reinforce wrap times is set to better secure 2 loads placed on top of each other Film Tension Control adjustment on the panel Separate start, pause and emergency stop buttons Power indicator Manual carriage up/down Variable Turntable Speed Carriage up/down speed control Manual/automatic exchangeable Turntable 1650mm diameter structural steel plate 85mm height floor to top of turntable Turntable drive 0-12rpm variable turntable speed by frequency changer position turntable alignment soft start Film carriage powered pre-stretch system up to 200% to min film consumption carriage door opens for effortless roll change and thread film film delivery variable speed by separate dc drive motor electronic film tension control adjustment on panel film dancer-bar with variable speed output Film carriage drive heavy duty double-chain carriage lift, calm and safety film carriage variable speed by frequency changer Option ramp top plate auto film attach and cut off system packing height:1800, 2400mm turntable diameter: 1800mm, 2000mm Packing height(max) 1800mm Packing efficency 20-40loads/hour Turntable speed 0-12rpm Turntable diameter dia.1650mm height85mm Turntable loading(max) 2000kg Machine weight 700kg Machine dimension 2545mm1650mm2270mm Power/voltage 0.75k ac220v Wooden or iron case
Controls * plc *photo-eye auto-height sensing pallet height *separate top , bottom & up-down wrap counter selector *overwrap time is set to create an overwrap *reinforce wrap times is set to better secure 2 loads placed on top of each other *film tension control adjustment on the panel *separate start, pause and emergency stop buttons *variable turntable speed *carriage up/down speed control Turntable *1650mm diameter structural steel plate *85mm height floor to top of turntable Turntable drive *0-12rpm variable turntable speed by frequency changer *position turntable alignment Film carriage *powered pre-stretch system up to 200% *carriage door opens for effortless roll change and thread film *electronic film tension control adjustment on panel *film dancer-bar with variable speed output Film carriage drive *heavy duty double-chain carriage lift, calm and safety *film carriage variable speed by frequency changer Option *ramp *top plate *auto film attach and cut off system *packing height: 2400mm *turntable diameter: 1800mm, 2000mm Packing efficiency 20-40 loads / hour Max load size(mm) 1200(l)x1100(w)x1800(h) (standard) Turntable speed 0-12rpm Turntable diameter 1650mm Turntable height 85mm Turntable weight capacity 2000kg Machine dimensions (mm) 2745( l)x1650( w)x2800 (h) Machine weight 700kg Power supply 220v 50hz 1phase (standard) Material lldpe - stretch film Film thickness 17-35 ¼ Film width 500 mm Core diameter 76.2 mm Maximum film. Diameter 260 mm Max. Weight of film roll 15 kgs
Auto filter Its a cut-and-dried story that somebody growing up in financially is someone has supported from back or solution who's problem under closely. Professional and for 32 yrs only to making of auto filters which air, cabin, oil, eco and fuel filter who dha hong (won kyung filter ind) co., ltd is manufacturer of whole korean vehiclef+s auto filter in south korea. Supplying to'hyundai", 'kia', gm-daewoo', ssangyong careers under contracted for ten years more with auto filters and for after markets. For other vehicles filter manufacturing are toyota, nissan, mazda, mitsubishi, honda, isuzu, suzuki of japan cars and few of europe and american. Certified against iso9001, iso14001 and qs9000 for all products covering. However, it cheap the price but grunge the quality. Contrary, excellent quality but expensive a little than other country. If it goes to excellent quality and prices are cheap is best on best! unfortunately there will be nothing to come to filling for those two things on the global. Negotiation! this is a tool of just business and calling to "win & win' strategy. Business is a negotiation for 'win-win on both. We/won kyung filter ind is welcome in anytime with open arms for hearing your opinions, suggestion and discussion if the subject were automotive filter. Thank you for your attention. From jung soo, jung Callrun@ec21.Com Www.Ec21.Com/callrun Personal (inner packing) and bulky packing following who buyer's pre orders.
ZR-40W CO2 laser power supply Feature 1.Easy Control: The start and stop of laser power can be easily controlled by TTL level� on this 40W laser power supply. And it has� protection switch to test the external water, ventilation, etc. 2.The 40w laser power supply adds a new function, that is timely scene judging which part is damaged� on� laser tube or laser power� supply. 3.Application: Acrylic sculpture, cut; Fabric sculpture, cut; Rubber sheet sculpture, cut, etc. 4.Easy control of laser power: Both 0-5V analog signal and PWM signal can control the laser power� on this40watt laser power supply. 5. This 40watt CO2 power supply has fast response speed and effect. 6.This 40 watt CO2 power supply has an aluminum alloy housing and a dedicated interface for the stamp engraving machine: K+/K -/D+/D -/G/IN/5. In addition, it also has; DC24V/5V output 7.� The� CO2 laser� power supply� has� feedback interface which can be used in closed-loop control and testing the working current of laser. 8.Because of many protect function, this 40W laser power source� dramatically lengthen the lifetime of� glass type CO2 tube. 9.� The� 40Watt CO2� power supply has open circuit protection: Under the condition of good protective earth, the power supply can work in open-circuit for a short time, which could avoid the damage to� laser power supply. 10. This ZR-40W CO2 laser power supply adopts K+/K-/D+/D-/G/IN/5V as control signal output interface and uses blue aluminum case. 11.Good compatibility: This 40W CO2 laser power supply can be applicable to most brands of 30Watt, 40Watt, 50Watt CO2� laser tube� made by different factories. Specification: Item 40W laser power supply Input Input voltage AC110/220V� �±10% AC frequency 47-440Hz Max input power 350W Max� input current 3A Output Max� output voltage DC25KV Max output current DC20mA(it depends on different brand 40watt CO2 laser tube) Efficiency More than 90%(full load) MTBF More� than 10000 hours Response speed 1ms(Time is from TTL.Signal is given to the output current up to 90% of pre-setting current) Withstand voltage Input-output,input-enclosure, AC1500V,10mA 60S, Output cathode is connected with enclosure. Environment Operation temperature(-10-40 degree celsius), related humidity s less than 90% Cooling Force air cooling Environment related Working temperature -20â??---50â?? Storage temperature -10â??---75â?? Related humidity Max 85^ RH(non-condensing) Cooling method Force air cooling(FAC) Altitude 100000feet of work,200000 feel of storage,no work. Cooling method Air force cooling(Fan cooling) Dimension LxWxH=165X144X80mm Weight 1.18KG
Detail: Size: 9" x 5.5" x 3.2" (L x W x Hï¼? Material: Faux leather, Golden hardware, chain shoulder strap, hardware detail Exterior Features: Removable, adjustable web shoulder strap Two-compartment Inside zipper pocket Lock closure Removable zipper pouch Questions: Email info@beanbing.com FAQ Q1.What service can you offer? we are the Full-package leather bag and accessories manufacturer. our service:dropping,design,source,manufacturing Q2.Where are your company located? Our company was located in Guangzhou, China. Q3.What's your payment term? T/T, L/C, Western Union, Paypal, and Alibaba. The normal payment term is 30% deposit before production, and 70% balance before shipment. Q4.Could you make OEM/ODM design? We are a traditional leather and eco-leather supplier. We can make any kind of designer items you desire and we pride ourselves on exclusively offering beautiful hand-made leather goods, low minimum quantities and quick re-order times. Purses, clutch, work bags, belts, laptop tote, crossbody, belt pack, stationery or any other leather accessory: whatever you like, we can make it! Q5.About technology? What can we do? what techniques we can do? PRINTING,EMBROIDERY,LASER CUTTING,EMBOSSING,BURNISHING,WEAVING,BRAIDING,PATCHES AND STICKERS,CROCHET,APPLIQUE,BASKET WEAVING,HAND PAINTING and we also use different material to create product,such as leather,nylon,pllyesters,canvas,bead,synthetics,satin,patchwork and so on. Q6.About Sample If stocked items, samples can be shipped out in priority. If out of stock, the sample will be produced according to customersdesign and requirements.Want to get a free sample?pls, contact us. Q7.About MOQ MOQ depends on material and design. Please consult our stuffs for details. Q8.About shipping by sea, by air, by express(DHL, FedEx IE, UPS Expedited, EMS, TNT, etc.). Transportation port: Guangzhou, Shenzhen, Hongkong Q9.How do you guarantee the product's quality? Before production, the pre-production samples will be made for checking details with customers. During the production and packing, there will be professional QC to inspect the products to ensure the products in good quality and correct details.
PFG500 Single Screw Extruder Features: Save time and money. PLC design and easy to operate. Long time span. No heating effect during operation. With latest technology and optimized design. Min - Max Dia:300-600mm. Production Per Hour: 9-18kg/h. Unlimited Length Automatic operation. POLYMER PTFE ROD RAM EXTRUDER AUTOMATIC MACHINE Product Description- RAM Extruder For PTFE Tube(00-600mm) Sunkoo PFG500 Tube Extruder is to extrude PTFE/UHMWPE Tubes. It is designed using latest technology, fully reliable and easy to operate for customers. Performance in terms of production and working hour capacity is competitive to other machines. Low maintenance is required , giving high production in market. PFG500 Single Screw Extruder Features Include: 1.Vertical Ram Extruder for PTFE Tubes 2.Ram extruding machine for PTFE Tubes. 3.Using for Pre-sintering PTFE material. 4.Suit for new PTFE material or Recycle PTFE material. 5. Adjustable Heating zone: 5 zone area 6. Long service life through solid workmanship and use of high quality components. 7. Measurement transducer like pressure, force and ram speed for permanent control of the extrusion process and extrusion speed. 8. Measuring and controlling system for constant extruder speed 9. Low space requirement through vertical construction 10.Operating through touch screen and recording of the extrusion process parameters Benefits: 1. Save time and money, good advantage price offer to customers. 2. Intelligent and easy-to-use operations. 3. Small workplace required due to its compact design and electricity saving machine. 4. Super quality output and the physical properties is adjustable. 5. Precise temperature control, reaches + -1 degree. 6. Long- life, with modern technology and optimized design. Q&A for Vertical Type Tube Ram Extruder · Which is the maximum extrusion capacity in sintered liner in meter per hour? A: Can change pressure time, each extrusion length and temperature to adjust the speed depend on size and wall thickness. about 1500 to 2500mm per hour. · Which is the maximum vertical dimension of the machine including the 7m of finished liner before cutting off? A: Machine net high is 2750mm. Consider about 1000mm higher space for mold change over with small crane on top. Machine install in second floor. ground floor for extruded tube. · Which is the maximum length of liner that can be extruded? A: Continue extrusion, no limited for length. For quite bigger size too heavy, need protection.
Ain unit--------1unit 38pin cable------1pc Obd cable--------1pc USB Cable--------2pcs Chip cable--------1pc------special for old cars. DVD software-----1pc The following diagnostic functions are supported: Read identification Displays complete identification of control unit, e.g. part number, software/hardware version, manufacturer, etc... Read fault codes Displays all stored and pending fault codes with complete description (e.g. "Rail pressure - too low pressure"). Program supports report printing or copy to clipboard. Clear fault codes This function clears all stored fault codes and other diagnostic information. Auto-scan (complete car scan/test) Detects all ECUs (electronic control units) installed in car and reads alldiagnostic fault codes. Measured Values Program displays live Data like Engine Speed, Battery voltage, Oxygen Sensor, Coolant Temperature, etc. Values can be displayed in graph, values at once, or full listing (all measured values). Logging to file is also supported, which allows offline analysis. Actuator test Actuator test activates particular actuator (e.g. turn on fuel pump, lock/unlock wheel, lock/unlock doors, cut off fuel, etc..) Programming functions/Adaptation This feature is of great importance in all vehicles because systems like Engine control units, Immobilizers, Airbags, Alarms, Body Control Units, and some others, require you to perform reset or programming procedures after car repair is done, or even configuration after replacing broken Control Unit. Hardware and software requirements Software requires at least Intel Celeron/Pentium III 400 MHz, 128 MB RAM, 50MB free HDD space and USB 1.1 port (USB 2.0 recommended) and Microsoft Windows 98 SR2/2000/XP with the latest service pack installed. This diagnostic scanner for comprehensive Citroenl and for Peugeotl cars diagnostic. You can do all as a authorized dealer does.This diagnostics software allows you to perform complete diagnostics of all from 1995 untill present models. Diagnostics is performed via OBD-II connector (which is located near steering wheel) or via manufacturer-specific connector (only older cars, pre-2001). It is easy to install , and it works in any laptop and computer. The software is in the DVD that come with the products.
Introduction AISI A2 Cold Work Tool Steel air hardening, with maximum dimensional stability during heat treatment, offering high abrasion resistance and good toughness. Generally supplied annealed to HB 231 max. A2 steel is an air hardening, cold work, tool steel. A 5% Chromium steel which provides high hardness after heat treatment with good dimensional stability. It is heat treatable and will offer a hardness in the range 57-62 HRC. Applications AISI A2 steel takes a place in tool steel range between AISI O1 and AISI D2, offering an excellent combination of good wear resistance and toughness. It may be regarded, therefore, as a ¡¡ãuniversal¡¡À cold work steel. For cutting operations the good toughness of AISI A2 gives excellent resistance to chipping of the cutting edge. In many cases tools made from this steel have given better tooling economy than high-carbon, high-chromium steels of the D3/W.-Nr. 2080 type. AISI A2 steel has much better machining and grinding properties.It can be used to make Bending Dies, Blanking Dies, Block Gauges, Cams, Coining Dies, Cold Forming Dies, Cold Shears, Cold Trimming Dies, Forming Dies, Knurls, Machine Parts, Mandrels, Plastic Mold Dies, Punch Plates, Punchers, Reamers, Ring Gauges, Roll Threading Dies, Rolls, Shear Blades, Slitters, Stamping Dies, Threading Taps, Trimming Dies, etc. HEAT TREATMENT Forging: Heat slowly toC then more rapidly to 1050-1100 Avoid working below . Reheat as often as necessary to maintain proper forging temperature. After forging cool very slowly. Heat slowly and uniformly. Cool in vermiculite or in other insulating media. Anneal after forging. Annealing: Soak thoroughly at then slow furnace cool at a rate of not more than 20C per hour. After annealing A2 a maximum hardness of 215 Brinell may be achieved.Protect against surface decarburization using controlled atmosphere or by pack-annealing. Hardening: Pre heat slowly to 600-700and soak. Continue heating to the final hardening temperature of 950/980 and allow the component to equalise. Quench in oil or cool in air.Temper immediately after hardening. Allow to cool to 125-F before tempering. Soak time is 15 minutes per inch of thickness. Minimum of 30 minutes. Tempering: Heat uniformly and thoroughly to the desired temperature and hold for 25 minutes per cm of thickness. A2 can be double tempering, after intermediate cooling to room temperature. Temper at 200C for a balance of hardness and strength or where strength is more important than hardness.Complete equalization of temperature throughout the tools is essential for good results. Double temper. Recommended temperature is 400-1000 hot rolled and hot forged according to the customer
PFG300 Single Screw Extruder Features:Save time and money;Advance designed;High output;Low energy consumption;Long-life;Tube OD Size range:150-300 mm;Production Per Hour in Kg:10-15;Length :Unlimited;Computerized. PTFE Tube Ram PFG300 Single Screw Extruder Features: Save time and money. PLC design and easy to operate. Long time span. No heating effect during operation. With latest technology and optimized design. Min - Max Dia:150-300mm. Production Per Hour: 10-15kg/h. Unlimited Length Automatic operation. 5 Heating Zones POLYMER PTFE ROD RAM EXTRUDER AUTOMATIC MACHINE Product Description- RAM Extruder For PTFE Tube(150-300mm) Sunkoo PFG300 Tube Extruder is to extrude PTFE/UHMWPE Tubes. It is designed using latest technology, fully reliable and easy to operate for customers. Performance in terms of production and working hour capacity is competitive to other machines. Low maintenance is required , giving high production in market. PFG150 Single Screw Extruder Features Include: 1.Vertical Ram Extruder for PTFE Tubes 2.Ram extruding machine for PTFE Tubes. 3.Using for Pre-sintering PTFE material. 4.Suit for new PTFE material or Recycle PTFE material. 5. Adjustable Heating zone: 5 zone area 6. Long service life through solid workmanship and use of high quality components. 7. Measurement transducer like pressure, force and ram speed for permanent control of the extrusion process and extrusion speed. 8. Measuring and controlling system for constant extruder speed 9. Low space requirement through vertical construction 10.Operating through touch screen and recording of the extrusion process parameters Benefits: 1. Save time and money, good advantage price offer to customers. 2. Intelligent and easy-to-use operations. 3. Small workplace required due to its compact design and electricity saving machine. 4. Super quality output and the physical properties is adjustable. 5. Precise temperature control, reaches + -1 degree. 6. Long- life, with modern technology and optimized design. Q&A for Vertical Type Tube Ram Extruder · Which is the maximum extrusion capacity in sintered liner in meter per hour? A: Can change pressure time, each extrusion length and temperature to adjust the speed depend on size and wall thickness. about 1500 to 2500mm per hour. · Which is the maximum vertical dimension of the machine including the 7m of finished liner before cutting off? A: Machine net high is 2750mm. Consider about 1000mm higher space for mold change over with small crane on top. Machine install in second floor. ground floor for extruded tube. · Which is the maximum length of liner that can be extruded? A: Continue extrusion, no limited for length. For quite bigger size too heavy, need protection.
Name: Communication Module Board Number of layers: 4 layers Material: FR-4 Board thickness: 1.6mm Surface Plating: Immersion Gold Special Process Description : 0.25BGA Special technology explanation: Black Matte Ink, gold thickness 5M Most important key points of OEM 1.FR4, Ceramic, High TG, Rogers, High Frequency RF, Halogen free, Aluminum-based PCB etc. available. 2.This FR4 PCB can be up to 32 layers. 3.ENIG, lead-free HASL, gold flash, OSP, gold finger, Hard & Soft Gold, immersion gold/silver/tin surface finish etc. available 4.Copper thickness is 1 to 6oz on the inner layer and 0.5 to 5oz on the outer layer. Has 3mil minimum line width and spacing, and as small as 0.2mm holes. 5.Board thickness: 0.3~3.5mm 1. 13 years professional PCB/PCBA manufacturing experience. Specializing in electronics manufacturing service including electronic design and engineering, PCB Fabrication & Assembly, SMT, custom printed circuit board products, One-stop cost-effective PCB Solutions, Electronic Components Procurement, prototyping, turnkey solution and other value-added service. 2. Excellent and high process capability, Specialized in 2 to 32 layer PCBs, FR4, Ceramic, High TG, Rogers, High Frequency RF, Halogen free, Aluminum-based PCB etc. available, with 3mil minimum line width and spacing and as small as 0.2mm holes. Copper thickness is 1 to 6oz on the inner layer and 0.5 to 5oz on the outer layer. 3. International quality & environment certifications. GX quick has been certificated by international quality & Environment systems such as ISO9001, ISO14001, SGS, RoHS, UL etc. 4. A large number of advanced equipment imported from the United States, Japan, Germany, Israel . Sophisticated equipment is gradually introduced to ensure excellent manufacturing process capabilities, such as: 1) Drilling machine 2) Full automatic plating line 3)Figure electric automatic line 4) Punching machine 5) Digital control routing machine 6) PTH 7) Antioxidant treatment line 8) Full automatic digital control V-CUT machine 9) Lami-machine 10) AOI testing machine 11) CCD-Exposal room 12) Automatic dry film machine 13) High speed flying probe machine 14) Fully automatic temperature control baking ovens. 15) Dedicated testing machine 5. Free samples with sample costs refunded after confirmed standard order, 24-hour quick-turn service. 6. High quality raw materials from top suppliers for laminates, copper foil, PP and more. Quality goal Total scrap rate â?¦ 1.8% customer satisfactionâ?§90% Template punctuality delivery rate â?§ 98% batch punctuality delivery rate â?§ 92% Customer complaint rate â?¦ 1% customer return rate â?¦ 0.5% Comprehensive Qualified rate â?§ 98% batch board utilization â?§ 90% Pre-launch rate: â?¦ 3% backwash solder mask â?¦ 3%, circuit â?¦ 2.5%
Wooden case is under fumigation, ventilation treatment and with desiccant material available Application Industry: caps, hats, T-shirts ,sweaters, ready-made garment, Shoes embroidery, fabric flat embroidery; Can do Cording, Chenille, Sequin , Boring embroidery by installing the optional devices Main Features: Suitable for flat bed embroidery, cap embroidery and finished garments embroidery Embroidery area: 400 x 450 mm/15.7" x 17.7" Auto thread cutting & color changing 270¡ã wide cap frame unit 5" color LCD display showing real time stitching DAHAO computer with USB port Japanese Rotary hook, bobbin & bobbin case Thread break detection Pre-Sew Design Trace capable Start, Stop, and Emergency Stop On-board lettering Speed: 200-850RPM Memory size: 1 million stitches. Max 2 million Stitch Length: 0.1~12.7mm Storage: 99 embroidery designs Electricity: 110V/60Hz or 220V/50Hz available Power consumption: 0.8kw/1.0kw/1.5kw Hoops/frames included: 2 x Shirt Front Round Hoop 9 cm (3.5") 2 x Shirt Front Round Hoop 12 cm (4.7") 2 x Shirt Front Round Hoop 15 cm (5.9") 2 x Shirt Front Round Hoop 18cm (7.1") 2 x Shirt Front Round Hoop 22cm (8.7") 2 x Jacket Back Square Hoop 29 x 29 cm (12" x 12") Cap attachment included: 2 x cap rings per head that snap into cap station for preparation then embroidery. 1 xhoop station per machine for easy snap in and snap out preparations of caps. 1 x cap driver per head that snaps into embroidery machine¡¯s bracket holder for hoops. Accessories included: Table top Operation Manual Tool Kit Bobbin Winder Optional devices: Independent Cording & Zigzag Device, Easy Chenillle Device , Sequin Device(single,dual), Boring Needle. Tubular (Cap) Embroidery Machines Series MODEL HEAD DISTANCE(mm) EMB SIZE (mm) HEAD NEEDLES MACHINE PACKAGE SIZE L*W*H (m) RU-FT-902 400 400*450 2 9 2*1.5*1.3 RU-FT-904 400 400*450 4 9 2.8*1.5*1.3 RU-FT-906 400 400*450 6 9 3.6*1.5*1.3 RU-FT-908 400 400*450 8 9 4.4*1.5*1.3 RU-FT-910 400 400*450 10 9 5.2*1.5*1.3 RU-FT-912 400 400*450 12 9 6.0*1.5*1.3 RU-FT-1202 400 400*450 2 12 2*1.5*1.3 RU-FT-1204 400 400*450 4 12 2.8*1.5*1.3 RU-FT-1206 400 400*450 6 12 3.6*1.5*1.3 RU-FT-1208 400 400*450 8 12 4.4*1.5*1.3 RU-FT-1210 400 400*450 10 12 5.2*1.5*1.3 RU-FT-1212 400 400*450 12 12 6.0*1.5*1.3. Packaging Details: Vacuum packing/wooden packing.
RYMAX Foam Cement Board | Exterior Drywall RYMAX Foam Cement Wallboard is a new building material designed for modern high-rise buildings, steel-structured buildings and new ecological residential buildings, featuring in anti-seismic, energy-conservative, fireproof, damp-proof, soundproof, thin, anti-shock, space-saving, mould-proof, not degradable and anti-insects. Filled with well-mixed polyphenyl granule and special cement, RYMAX Foam Cement Wallboard is light weight with good heat preservation, sound proof, heat insulation, fire proof and high weather ability. It is also resistant to degradation, mildew, termites. Honeycomb structure formed by evenly distributed polyphenyl granule gives the wallboard high impact resistance and good nail-holding grip. RYMAX Foam Cement Wallboard is sandwiched by two facing boards and filled with polystyrene concrete in the core layer. The facing board is the Fiber Cement Board or Fiberglass Magnesium Board developed with our own technology with outstanding advantages such as high-strength, fireproof, damp-proof, anti-shock and pollution-free. The core layer made of polystyrene concrete heavily reduces the weight and enables the panel to form multi-arched structures and have high flexural strength and compressive resistance. The groove and tongue structure helps to build a strong and stable structure in one piece. The industrialized production helps shorten the construction period and enhance the installation efficiency, also the panel is nice decoration and easy for installing piping. Since the wallboard is light and thin, it greatly reduces the loads of the foundation, beams and columns and thus lowers the construction cost and increase the usable area. No coat plastering is required for the smooth facing board and the construction period can be greatly shortened. RYMAX Foam Cement Wallboard is ushering into a new period in the modernized construction field. Features: * Environment-friendly: The facing board of RYMAX Foam Cement Wallboard has been certified by National Environment Protection Administration and the core layer of the panel mainly consists of fly ash and polystyrene beads. It's nonpoisonous, no harms to domestic animals, non-radioactive and meets the GB6566-2001 standard. * Energy-conservative: The polystyrene concrete in RYMAX Foam Cement Wallboard core layer forms a honeycomb structure which ensures good heat-insulating performance with low heat conduction value, while most other panels are of hollow structure in which case the air flow accelerates the heat conduction and thus have lower heat-insulating performance than RYMAX Foam Cement Wallboard. With a density of 750kg/m3, RYMAX Foam Cement Wallboard weights only 1/5 of other panels that are of the same performance and helps save 80% transportation costs. * Fire-proof: RYMAX Foam Cement Wallboard has outstanding fire-proof performance. The fire resistance limit excesses 5 hours under 1000oC with no emission of poisonous gases. The non-flammability has reached A Grade standard as per GB8624-1997 under the tests run by the National Center for Testing of Fire Building Materials. It can be applied as fire-proof walls in steel-structured or concrete-structured industrial and civil constructions such as theatres, shops, factories and warehouses, or fire-proof coating for steel-structure beams and columns, or fire-proof enclosures for gas duct sealing and elevator shaft, etc. * Anti-seismic: As one piece, RYMAX Foam Cement Wallboard has a sandwich compound structure. The cement fiber facing board also has high strength and excellent tensile and shear resistance. The panel is pre-fabricated and the in-between of panels are connected with re-bars. The groove and tongue ends are connected with high-strength polymeric anti-crack mortar and makes the anti-shock performance 1.5 times stronger than that of common brick walls. The entire strength will be highly enhanced after combining with steel structure framework anchoring fixation. The installation is of high efficiency and avoids the pouring and curing process of concrete beams and columns. It has outstanding anti-seismic performance applying in building extra-high and wide-spanned walls and meets the National Standard of No Damages from Small Earthquakes, Repairable from Middle Earthquakes and No Collapse from Large Earthquakes. * Light-weight: RYMAX Foam Cement Wallboard weights only 750kg/m3, in other words, 1m2 of RYMAX Foam Cement Wallboard weighs only 1/5 that of solid brick walls and 1/2 of common light walls. 50mm, 75mm, 100mm thick RYMAX Foam Cement Wallboards can be freely used for separations on regular construction floorings and no damages will be caused to the structure. (The required flooring loading capacity should be more than 240kg/m2). * Increase the usable area and decrease the construction cost: 75mm thick RYMAX Foam Cement Wallboard (plastering-exempted) is 85mm thinner than that of a 120mm thick brick wall (160mm thick with coat plastering), every 11.76 linear meter of RYMAX Foam Cement Wallboard Wall increase 1m2 usable area and the entire area usage rate increases about 5%. With the same usable area, take a 100m2 room for example, using RYMAXTM Foam Cement Wallboard help increase about 5m2 usable area. So using RYMAX Foam Cement Wallboard as separation walls can highly increase the use value and create invisible value (50mm RYMAX Foam Cement Wallboard is most preferred in Shops). RYMAX Foam Cement Wallboard weighs about 750kg/m3 and 1/5 of regular brick walls, thus it greatly reduces the dead weight of the building. By using RYMAX Foam Cement Wallboard, the usage amount of materials for foundations, beams and columns can be greatly reduced and thus lowers the total construction costs. * Soundproof: Both the high-density RYMAX Fiber Cement Board/RYMAX Fiberglass Magnesium Board and Honeycomb structured core layer have excellent soundproof and sound absorbing performances. 100mm and 125mm RYMAX Foam Cement Wallboard are rated 50dB sound-insulation and can be widely applied in places which demands good soundproof performances such as KTV, Modern Classroom with Configuration, Theatres, Concert halls and Conference rooms, etc. * Waterproof and Damp-proof: The reinforced fiber cement or Fiberglass Magnesium facing board has outstanding waterproof performance; it does suffer from moister even in highly moisture environment and moisture climate. The water tank made of RYMAX Foam Cement Board doesn leak or mould or crack. The external side has no condensed water. RYMAX Foam Cement Wallboard can be applied in moisture environment such as kitchens, bathrooms, basements, Sound rooms and under-ground civil defenses. * High Stability and Excellent Anti-aging Performance: Three layers of RYMAX Foam Cement Wallboard are made of cement and have excellent stability. The deformation rte is low while the softening coefficient is high. Also it has good acid and alkaline resistance. It meets the requirements for construction life cycle since it does not turn halide, or mould, or crack, or suffer from oxidation or weathering. * Easily Stick and Nail: RYMAX Foam Cement Wallboard can stick strongly with building glue, cement mortar and internal/external wall dopes. Tiles, marbles and wooden plaque can be directly sticked. Unlike the hollow walls which can be nailed or hanged, the hanging force of each single points of RYMAX Foam Cement Wallboard is more than 1000N, nails or expansion bolts can be directly drilled into the panel for hanging heavy appliances such as ACs, TVs and kitchen ventilators. Wiring and piping channels can be cut directly in the panel. * Short Construction Period, High Efficiency and No Pollution: Pre-fabricated installation applied; smooth facing board which requires no plastering; no scaffold needed for walls not higher than 3.2m; thin-webbed structure; low transportation volume; several times more efficient than building regular walls. * Simple Installation and Clean Construction Site: Regular labors are able to learn to install panels within a short period of simple training. The installation tools are simple and the length/width can be easily adjusted by cutting. RYMAX Foam Cement Wallboards can be easily stored and merely have no wastage. Since it generates little construction garbage, using RYMAX Foam Cement Wallboard helps create a clean construction site. export packing.
Please read completely through these insturction before using the crimper. your DOUGLAS DE 1600 HAND CRIMPER is supplied factory pre-set for quic change-over between most aluminium window systems. PLEASE NOTE : The crimping bench should be constructed in such a way as to offer suitable support for the material being crimped, in order to protect material being crimped from damage, it is advisable to cover the bench bearers with carpet to similar and keep the surfaces clear of swarf or objective likely to damage material surfaces. SETTING UP Remove crimper from box, locate on corner of suitable bench, which must be a robust and stable comstruction. Secure to bench with four M10 counters unk bolts or screws. Insert handles into handle sockets and secure with loking screws which must locate into dimples provided on handle ends. Remove toggl clamp from packing and fix to top of anvil block with two M6 x 10 socket cap screws which are located in the anvil block. WARNING : (1) Do not operate the crimper unless both handles are secured as described above, failure to comply may result in the handles slipping out of the sockets and causing a hazard to the operator. (2) The punch heads are sharp and must be handled with care. The DE 1600 hand crimper is designed for two handed operation by one operator only. It is the operators responsibility to ensure that the path of the punch heads are unobstructed are operating the hand lever handles. TOOLING CHANGES ANVIL INSERT (1) Loosen locking screws (R) Fig. 1 and lift of insert (Q) (2) Slide alternative insert into place, ensure face marked "TOP" is uppermost, locate firmly on bottom face or pins, ensuring that the rear face of the anvil insert sits flat against the anvil block. CRIMP PUNCH HEADS (1) Remove completely the retaining screws (J) Fig 1 (2) Pull Punch Heads our of location slots. (3) Clean all location faces. (4) Select correct punch heads to match anvil insert, push into location slots, replace retaining screws (J) and screw down. TOGGLE CLAMP ADJUSTMENT (1) Select short mitred corner from off-cuts of profile to be crimped, insert correct cleat (s) and corner brance (s) and locate corner on anvil insert. (2) Adjust clamp spindle (v) Fig 1. so that when clamp lever locks ito forward locked position the test corner is held by the clamp pd, with a pressure equivalent to a firm finger pressure. (3) Tighten clamp spindle lock nuts. PLEASE NOTE ! If the clamp pressure is set to high, distortion of profile will occur resulting in poor crimping. CRIMPING TEST JOINT Before starting production it is advisable to test toooling changes as follows :- (1) Leave small sample corner piece in position after setting Clamp. (2) Bring the handles in towards the centre until Cr5imp Heads touch the profile. (3) Open box section profiles the crimp action can be performed by applying equal pressure to both handles simultaneously until the Link Ars (F) Fig 1. lock into a straight line with Punch Heads. (4) When crimping heavy gauge or closed box section profiles it may be found easier to hold one Crimp Punch Head firmly against profile for support whilst the other Head is crimped into it's full depth. Then with a slight alteration in stance, the first head can be pushed to it's full depth. (5) Both crimp Punch heads should be withdrawn from the profile simultaneously. PLEASE NOTE ! Under no circumstances should any one Punch Head be used without firm support of the other one. failure to observe this basic rule will result in the profile frame moving on the anvil insert, a poor crimped joint being produced and possible damage to the Crimper. SETTING CHECK The crimper is supplied factory set and has been test crimped prior to dispatch if for any reason the setting of the crimpter is in doubt the following procedure should be adopted. (1) Cut a sample corner of material to be crimped (2) Carefully check the cut and establish that the cut is a true 45, flat and at 90 to both legs of the section. (3) Offer the appropriate setting piece to the anvil insert and check that the setting is as shown Fig. 2 (4) The punch heads tips should engage onto the slope of the cleat as shown and should either just "skim" the setting piece or clear with minimal clearance. (5) The punch heads should ride down the slope until the link arms lock into straight line with the punch heads. The initial setting for the depth to which the punch heads should run is approximaterly two thirds of the full tepth see Fig. 2 The optimum setting is best established by carrying out test crimps and checking results. PLEASE NOTE A Setting Piecd can be made up by fixing with a suitable adhesive, two packing strips to the back of a cleat that is to be used in the system. The packing strips must be eqial in thickness to the wall of the profile to be crimped. ADJUSTMENTS Should the crimpel require resetting, both the anvil position and the depth of bite of the crimp heads are fully adjustable ANVIL ADJUSTMENT 1) Remove the clamp assembly (U) by removing 2 screws (T), this will reveal a socket head screw. Slacken this screw. 2) Slacken the four nuts at the extreme rear of the crimper (S). 3) Using the setting piece as a guide, adjust the anvil towards or away from the crimp punch heads by turning the nuts. Set the anvil so that the crimp punch heads ride down the slope of the setting piece as shown in Fig 2. ADJUSTMENT OF PUNCH HEADS Each ram assembly is secured tgo the casting by 2 screws (P), slaken to allow the punch head assembly to slide in the casting. By slackenning the lock nut and adjusting screws (N), the position of the punch heads can be adjusted. Adjustments should be initially set so that the crimp punch heads run down the slope on the setting piece to approximately two thrids depth. The assembles must be locked in this position by re-rightening the socket screws (P). The final depth setting is best established by carrying out test crimps and making minor adjustments until satisfactory results are obtained. NOTE Setting the bite of the punch heads too deeply is to be discouraged, if set too tight the resulting joits will not necessarily be tight. "bottoming out"on the cleat is not necessary when trying to obtain a good quality crimp. An indication that the cimper is set over tight, is difficulty encountered when withdrawing crimp punch heads from the crimped material Ensure that all the bolts and nuts are tightened after adjustment have been carried out to maintained settings. is it important that when the crimper is finally set, the heads should both run equal depths on the test piece. It is important that the anvil is set so that the crimp punch heads ride down each slope in the same manner, i.e. the anvil must not be set askew relative to the crimp punch heads. MAINTENANCE Standard packing by using wooden box for which we have government policies and standards for safe delivery of the products. we are also arranging the third party inspection for quality of products and packaging which is useful for clearance of goods specifically for Africa.
Reclaimed wiper rags., bedsheets, white terry towel, color terry towel, white knit, white polo, color knit, color polo, white jogging, color sweat, jeans, light color knit, flannel, 100% cotton rags, cut uncut.