Electric Pumps Suppliers and Manufacturers

Multiple Protections: Dry run protection Phase loss protection Overload/no load protection Short circuit protection Over-voltage protection Pump stalled/antiseizing protection Undervoltage protection Pump shaft rust protection Major Features: 1,Pressure control: electric contact pressure gauge or pressure switch 2,Water level control: probe or float switch 3,Multifunction display â?? visualization of: voltage, motor current, upper/lower tank status and alarms 4,Upper tank for water supply control and lower tank for drainage control 5,Operation mode: AUTO/MANUAL switch 6,Fault indication: fault tracking,last 10 fault reason display,audio/light alarms. 7,Anti-card protection,long-term non-use of the pump, 15 days to start once. 8,Setting protection current for motor overload/no-load,no-load delay restart time adjustable. 9,Automatic restart when voltage comes to normal rating after over-voltage/under-voltage protection. 10,Automatic restart after power failure recovery. 11,Time setting ON/OFF 12,Push button for adjustments and set up from display 13,Restore factory setting: press both "Overload" and "NO-Load"for 3 seconds. 14,Automatic re-starting pump from dry running,restart time range 0-999 minutes adjustable.

Multiple Protections:   Dry run protection Phase loss protection Overload/no load protection Short circuit protection Over-voltage protection Pump stalled/antiseizing protection Undervoltage protection Pump shaft rust protection Major Features: 1,Pressure control: electric contact pressure gauge or pressure switch 2,Water level control: probe or float switch 3,Multifunction display â?? visualization of: voltage, motor current, upper/lower tank status and alarms 4,Upper tank for water supply control and lower tank for drainage control 5,Operation mode: AUTO/MANUAL switch 6,Fault indication: fault tracking,last 10 fault reason display,audio/light alarms. 7,Anti-card protection,long-term non-use of the pump, 15 days to start once. 8,Setting protection current for motor overload/no-load,no-load delay restart time adjustable. 9,Automatic restart when voltage comes to normal rating after over-voltage/under-voltage protection. 10,Automatic restart after power failure recovery. 11,Time setting ON/OFF 12,Push button for adjustments and set up from display 13,Restore factory setting: press both "Overload" and "NO-Load"for 3 seconds. 14,Automatic re-starting pump from dry running,restart time range 0-999 minutes adjustable.

Multiple Protections:   Dry run protection   Phase loss protection Overload/no load protection   Short circuit protection Over-voltage protection   Pump stalled/antiseizing protection Undervoltage protection   Pump shaft rust protection Major Features: 1,Pressure control: electric contact pressure gauge or pressure switch 2,Water level control: probe or float switch 3,Multifunction display â?? visualization of: voltage, motor current, upper/lower tank status and alarms 4,Upper tank for water supply control and lower tank for drainage control 5,Operation mode: AUTO/MANUAL switch 6,Fault indication: fault tracking,last 10 fault reason display,audio/light alarms. 7,Anti-card protection,long-term non-use of the pump, 15 days to start once. 8,Setting protection current for motor overload/no-load,no-load delay restart time adjustable. 9,Automatic restart when voltage comes to normal rating after over-voltage/under-voltage protection. 10,Automatic restart after power failure recovery. 11,Time setting ON/OFF 12,Push button for adjustments and set up from display 13,Restore factory setting: press both "Overload" and "NO-Load"for 3 seconds. 14,Automatic re-starting pump from dry running,restart time range 0-999 minutes adjustable.

Multiple Protections Dry run protection Phase loss protection âOverload/no load protection â?  Short circuit protection â?  Over-voltage protection â?  Pump stalled/antiseizing protection â?  Undervoltage protection â?  Pump shaft rust protection Major Features: 1,Pressure control: electric contact pressure gauge or pressure switch 2,Water level control: probe or float switch 3,Multifunction display â?? visualization of: voltage, motor current, upper/lower tank status and alarms 4,Upper tank for water supply control and lower tank for drainage control 5,Operation mode: AUTO/MANUAL switch 6,Fault indication: fault tracking,last 10 fault reason display,audio/light alarms. 7,Anti-card protection,long-term non-use of the pump, 15 days to start once. 8,Setting protection current for motor overload/no-load,no-load delay restart time adjustable. 9,Automatic restart when voltage comes to normal rating after over-voltage/under-voltage protection. 10,Automatic restart after power failure recovery. 11,Time setting ON/OFF 12,Push button for adjustments and set up from display 13,Restore factory setting: press both "Overload" and "NO-Load"for 3 seconds. 14,Automatic re-starting pump from dry running,restart time range 0-999 minutes adjustable.

Water pump is an automotive engine parts. Its function is to cool the engine by allowing the coolant flow from radiator to cylinder's water jacket.

Hot water circulation pump with timer integrated. This pump makes sure hot water is always available at the tap without delay. Fully automatic

EXYTB-60 is designed according to vane pump's feature, with mechanical seal and explosion proof single-phase asynchronous motor for oil dispensers that guarantees constant reliability, even in low temperature. Cast-iron pump casing, treated against corrosion and paint-finished. In-built 100micron filter, easy to clean. Continuous running.1" Threaded joints on pump casing. Bypass valve built into pump casing. It's easy to operate, being widely used in motorcade, factory, house using for diesel, kerosene and gasoline. It is made in stainless steel, with stainless nozzle and corrosion resistant hose . It also can extract chemical liquids. Technical performance Medium Gasoline,Diesel oil, Coal oil etc. Flow Rate 60L/min Power 220V¡À10% 50Hz 750W Motor Rotate Speed 2800rpm Noise level 70dB(A) End pressure 0.02MPa Max.Operating 0.3MPa Tube diameter 1" Tube Nozzle Client choice Weight 15Kg Ex Marking Exd ¢ò BT3.

YTB-40 For fueling diesel, Kerosene, not for gasoline Mechanical seal that guarantees constant reliability, even in low temperatures. Cast-iron pump casing, treated against corrosion and paint-finished. Vane pump with steel rotor Bypass valve built in. In-built 100-micron filter, easily accessible for cleaning. Induction motor with aluminium casing. Grade of protection: IP54. Continuous running. Technical Specification Model: YTB-40 For fueling Kerosene Flow Rate: 40L/min Max. Pressure 3 Bar Power: 12V 24V Inlet&outlet 1" Power: 160W By pass Valve : Yes Head(m) 15M Suction(m) 3M.

Wodenchina MP2000 Series High Pressure Electric Pump Single-acting, stable performance. The power for Hydraulic bolt tensioner. The pressure is easily adjusted in the range of 70-2000 Bar. High-precision pressure gauge for precise pressure adjustment. CEJN quick connector, good quality, quick and easy operation. Light weight, small size, easy to carry. WODEN hydraulic, products quality is stable,good price , timely after-sales. It is a brand of hydraulic wrenches and bolt tensioners in China, providing high quality bolt solutions for China and foreign users. Our products have been sold to: China Petroleum, Sinopec, CNOOC, Sinochem, China Oil and Gas, and many other well-known Chinese companies. At the same time, ,we also provide products and services for many medium-sized and above companies. Foreign markets are also constantly expanding, and the products have been sold to the United States, Russia, South Korea, Malaysia, Vietnam, Africa and other countries and regions. And by the recognition of domestic and foreign users and praise. The products have obtained many patents in China and passed ISO9001:2015, CE product certification.

Suitable for conventional oil pumping and large displacement oil extraction, small pump depth-pumping and heavy oil, high pour-point oil, injection well, cluster deviated well.

Model 4D-SY(6.3-80MPa)electric hydraulic test pump is the up-to-date series product designed by the Joint Design Group for Hydraulic

The electric hydraulic test pump3D-SY750 is mainly used in hydrostatic test for various pressure containers, oxygen cylinder

Application: For high viscosity grease injection. Suitable for all kinds of power machine grease injection. Apply for injection 0-3#grease of engineering machine. Power supply: AC220V/110VAC/24VDC Barrel capacity: 40KG Output capacity: 0.4L/Min Output pressure:

Application: For high viscosity grease injection. Suitable for all kinds of power machine grease injection. Apply for injection 0-3#grease of engineering machine. Power supply: AC220V ;110VAC;24VDC or 12VDC. Barrel capacity: 20-30L Output capacity: 0.6L/Min Output pressure:

Application: For high viscosity grease injection. Suitable for all kinds of power machine grease injection. Apply for injection 0-3#grease of engineering machine. Power supply: can chose (220V;24V;12V;110V). Barrel capacity: 20-30L Output capacity: 0.6L/Min Output pressure:

Application: For high viscosity grease injection. Suitable for all kinds of power machine grease injection. Apply for injection 0-3#grease of engineering machine. Power supply: AC220V/24V Barrel capacity: 40KG Output capacity: 0.4L/Min Output pressure:

Application: For high viscosity grease injection. Suitable for all kinds of power machine grease injection. Apply for injection 0-3#grease of engineering machine. Power supply:AC220V/24V Barrel capacity:40KG Output capacity:0.4L/Min Output pressure:

â?¢ Can work when the power is off â?¢ High performance and low power consumption â?¢ Switch Automatically among the three pumps â?¢ Both Manual and Automatic operation is available â?¢ YE3 high efficient motor with protection IP55 class F â?¢ With quality NSK bearings,