Electronic Potting Silicone Rubber is a kind of low viscosity, Inherent flame resistance, two components addition cured potting silicone with heat-conducting. It cures with both on room temperature and heated temperature. It has the feature of the higher temperature the faster of the curing time. It can be applied to electronic components for insulation, waterproofing, fixed and flame retardant. It mainly applied in electronic components surface with materials of PC(Poly-carbonate)ã??PPã??ABSã??PVC, etc. and metal materials. 2. Typical Application of Electronic Potting Silicone Rubber HY-9055 electronic potting silicone rubber could be applied to - high powered electronics, - DC/DC module and circuit board which requires heat dissipation and high temperature resistance. -It can be broadly used for LED screen, Wind Power Generator, PCB substrate, etc.
1. Product Feature of Electronic Potting Silicone Rubber Electronic Potting Silicone Rubber is a kind of low viscosity, Inherent flame resistance, two components addition cured potting silicone with heat-conducting. It cures with both on room temperature and heated temperature. It has the feature of the higher temperature the faster of the curing time. It can be applied to electronic components for insulation, waterproofing, fixed and flame retardant. It mainly applied in electronic components surface with materials of PC(Poly-carbonate)PPABSPVC, etc. and metal materials. 2. Typical Application of Electronic Potting Silicone Rubber HY-9055 electronic potting silicone rubber could be applied to - high powered electronics, - DC/DC module and circuit board which requires heat dissipation and high temperature resistance. -It can be broadly used for LED screen, Wind Power Generator, PCB substrate, etc. 3. Technical Guidelines of of Electronic Potting Silicone Rubber a, Pls put part A and part B in separate container and stir evenly before mixing the two part together. b, Mixing Ratio: part A: part B = 1:1 c, Deaeration the mixture in vacuum pump under 0.08 MPa for 3-5 minutes.Then the mixture could be used for pouring. Note: The thickness of the silicone affects the curing time. If the silicone used is a little thick,then the curing time will be a little longer.The temperature also affects the curing time.When in lower temperature, we suggest customers appropriately heat the mixture to accelerate vulcanization. With temperature of 80ï½?100, the silicone will cure in 15 minutes; while in 25 room temperature, the silicone will cure around 8 hours. 4.Notes of Electronic Potting Silicone Rubber a.The following material may hinder the curing of HY-9055, So pls use after the test. When necessary, pls clean the application areas. Organotin compound or Condensation silicone with organotin Sulphur, sulfide and sulfur rubber materials. Amine compounds as well as contains the amine materials. Pewters solder flux b. HY-9055 should be sealed storage.The mixture should be used up disposably to avoid causing waste. c. HY-9055 belongs to non-dangerous goods, but keep away from mouth and eyes. d. When it gets stratified after a period of storage, Please mix it evenly before using,which does not affect the performance
Factory price rtv2 silicone rubber for crafts molding Crafts Molding Silicone 1.Description 2. Technical Datasheet Typical general characteristics Inspection MethodValue Product data (Catalyzed A+B)C-820C-825 HardnessShore A20±225±2 Mix RatioA:B100:3100:3 Color/WhiteWhite Pot life25 °C (77F)30-40mins30-40mins Curing time25 °C (77F)3-4 hours3-4 hours Mixed viscositymPa.s16000±100020000±1000 Tear-strengthkg/cm20±222±2 Tensile-strengthM.pa3.6±0.54.0±0.5 Elongation%400±50450±50 Shrinkage%?¤0.3?¤0.3 Note: This is a 100A:3B mix ratio product that must be measured by weight. The choosing of suitable hardness should be according to the size and pattern design of the products. If large products and therefore multiple-piece molds are needed by customers, silicone rubber with higher hardness will be required for the molds. Conversely, soft silicon is indispensable for molds with complicated pattern and delicate details. The amount of curing agent admixture depends on the actual need of customers. More will be added for speedy drying and fast release and less when otherwise. 3. FEATURES Low viscosity,great flexibility,Extra low shrinkage,Chemical resistance,release properties, Easy to work with,High tear strength,Heat Resistance,various color is available,High reproduction rate 4.SHELF LIFE: When stored at or below 32°C (89.6°F) in the original unopened containers, C-8 series Silicone Base and its Curing Agents have a usable life of I0 months. 5.Package Silicone base:1kg/drum; 20kg/drum;25kg/drum;200kg/drum. Curing Agent: 30g/bottle; 1kg/bottle
Cheap liquid silicone rubber to make molds for lost was casting Lost Wax Casting Silicone 1.Description GC RTV silicone C-825 are good for lost wax casting. They are widely used for lost wax process of bronze casting to make accurate reproductions of original sculpture. 2. Technical Datasheet Typical general characteristics Inspection MethodValue Product data (Catalyzed A+B)C-825 HardnessShore A25±2 Mix RatioA:B100:3 Color/White Pot life25 C (77F)30-40mins Curing time25 C (77F)3-4 hours Mixed viscositymPa.s20000±1000 Tear-strengthkg/cm22±2 Tensile-strengthM.pa4.0±0.5 Elongation%450±50 Shrinkage%?¤0.3 Note: This is a 100A:3B mix ratio product that must be measured by weight. The choosing of suitable hardness should be according to the size and pattern design of the products. If large products and therefore multiple-piece molds are needed by customers, silicone rubber with higher hardness will be required for the molds. Conversely, soft silicon is indispensable for molds with complicated pattern and delicate details. The amount of curing agent admixture depends on the actual need of customers. More will be added for speedy drying and fast release and less when otherwise. 3. FEATURES Low viscosity,great flexibility,Extra low shrinkage,Chemical resistance,release properties, Easy to work with,High tear strength,Heat Resistance,various color is available,High reproduction rate 4.Appearance Part A: Silicone rubber is a white liquid Part B: Catalyst is a non-toxic and odorless liquid, white transparent color. ATT: We can provide fast/medium/slow catalyst of for hot, warm or cold season. 5.SHELF LIFE: When stored at or below 32C (89.6F) in the original unopened containers, C-8 series Silicone Base and its Curing Agents have a usable life of I0 months. 6.Package Silicone base:1kg/drum; 20kg/drum;25kg/drum;200kg/drum. Curing Agent: 30g/bottle; 1kg/bottle
China supplier Rtv mould making Silicone rubber for Taxidermy Molding Taxidermy Molding Silicone 1.Description 2. Technical Datasheet Typical general characteristics Inspection MethodValue Product data (Catalyzed A+B)C-810C-825C-830 HardnessShore A10±225±230±2 Mix RatioA:B100:3100:3100:3 Color/WhiteWhiteWhite Pot life25 °C (77F)30-40mins30-40mins30-40mins Curing time25 °C (77F)3-4 hours3-4 hours3-4 hours Mixed viscositymPa.s6000±100020000±100023000±1000 Tear-strengthkg/cm12±222±223±2 Tensile-strengthM.pa2.0±0.54.0±0.55.0±0.5 Elongation%320±50450±50460±50 Shrinkage%?¤0.3?¤0.3?¤0.3 Note: This is a 100A:3B mix ratio product that must be measured by weight. The choosing of suitable hardness should be according to the size and pattern design of the products. If large products and therefore multiple-piece molds are needed by customers, silicone rubber with higher hardness will be required for the molds. Conversely, soft silicon is indispensable for molds with complicated pattern and delicate details. The amount of curing agent admixture depends on the actual need of customers. More will be added for speedy drying and fast release and less when otherwise. 3. FEATURES 1.Low viscosit 2.great flexibility 3.Extra low shrinkage 4.Chemical resistance 5.release properties 6.Easy to work with 4.High tear strength 5.Heat Resistance 6.various color is available 7.High reproduction rate 4.SHELF LIFE: When stored at or below 32°C (89.6°F) in the original unopened containers, C-8 series Silicone Base and its Curing Agents have a usable life of I0 months. 5.Package Silicone base:1kg/drum; 20kg/drum;25kg/drum;200kg/drum. Curing Agent: 30g/bottle; 1kg/bottle
Model530 Colorwhite Mixing ratio (%)2% Pot life (mins, under 2530-40 Curing time(hrs, under 25)3-4 Hardness ( shore a )30±2 Tensile-strength (mpa)4.2 Tear-strength (kn/m)26±2 Viscosityafter a/b mixed , mpa.S27000±2000 Shrinkage rate (%0.2% Elongation450
Silicon-carbon alloy is a new type of alloy for converter, customers choose this to, replace most of ferrosilicon, silicon carbide and recarburizer, Used in converter, smelting deoxidation alloying process The characteristics Reduce the cost of steelmaking, increase economic, efficiency, improve product quality, stable performance, improve the quality of, molten steel, improve product performance, reduce the amount of alloy added,, reduce the cost of steel and increase economic efficiency.
The characteristics: Reduce the cost of steelmaking, increase economic efficiency, improve product quality, stable performance, improve the quality of molten steel, improve product performance, reduce the amount of alloy added, reduce the cost of steel and increase economic efficiency. Silicon carbon alloy instead of ferrosilicon, silicon carbide, recarburizer, reducing the amount of oxygen scavenger, a converter for deoxidizing alloy, the effect of stability, steel chemical composition, mechanical properties and internal quality are better than the traditional process. By testing and production shows that using Si-C alloy to converter deoxy-alloy process, greatly reduce the cost of steel, creating considerable economic benefits, improve the market competitiveness of steel. The effect of using a silicon-carbon alloy species 1, can replace ferrosilicon and carburant, FeALSi dosage is also reduced, can effectively reduce the cost of steel 6-10 yuan / ton steel 2, smelting carbon steel, special steel and some low-alloy steel, the effective recovery of effective elements.
The main grades our products cover: Grade Si Fe(max)Al(max)Ca(max)P(max) 553 98.5%min 0.50% 0.50% 0.30% 441 99% min 0.40% 0.40% 0.10% 421 99.2% min 0.40% 0.20% 0.10% 3303 99.3% min 0.30% 0.30% 0.03% 50ppm 2202 99.5% min 0.20% 0.20% 0.02% 40ppm Packing: In 1mt big bags Shipment: With in 15 days after comfirming the order Apperance:Dark gray Physical Property: High melting point and resistivity, good heat resistance and good anti-oxidation effect. Particle Size: (10-100)mm. Application and use: 1. Used in aluminum: An additive to aluminum alloys, silicon is used to increase the fluidity and tenacity of Aluminum and its alloys, which enjoy good castability and weldability accordingly. 2. Used in organic chemicals: Silicon metal is used in manufacturing a number of sorts of silicones, resins, and lubricants. 3. Used in electronic parts: Silicon metal is used in producing monocrystalline and polycrystalline silicon of high purity for electronic parts, such as semi conductors, etc.
Fineway can custom manufacture ceramics balls, rollers, full ceramic bearings and hybrid bearings per customers request. We can do Grade 3 to Grade 100 ceramic balls. Please contact us today to get a quotation for your requirement.
Fineway offers high quality ultra fine silicon nitride powder, the average particle size ranges from submicron order to coarse grain powder. With the high Purity and α phase crystal content, our powder can be widely used in solar and ceramic structural applications.
Characteristics The industrial silicon powder is also called metal silicon powder. It is silver grey or dark grey powder and appears metallic luster. Its characteristics are high melting point, good heat-resisting, high resistivity and excellent anti-oxidation. It's well known as the industry gourmet powder used as the indispensable basic raw materials of a lot of high-tech products. Application Industrial silicon powder is widely applied to the refractory material, powder metallurgy industry so as to improve the products heat-resisting performance, wear resistance and oxidation resistance. The products of the refractory material, powder metallurgy industry are used in the steelmaking furnace, kilns, etc. Standard Size: 200Mesh; 325Mesh; etc The packaging and granular size can be produce according to customer demand. Si Fe Al Ca 98.5% 0.5% 0.5% 0.3% 99.0% 0.4% 0.4% 0.1% 99.0% 0.3% 0.3% 0.03% 99.0% 0.2% 0.2% 0.02%
Characteristics Ferro Silicon Magnesium nodulizer ( FeSiMg ) uses the advanced smelting craft production the nodulizer product, the organization is compact, the ingredient is stable, does not have the deflection evenly, the MgO content is low.The spheroidization response is steady, the magnesium absorption rate is high, the anti-decline time is long. After spheroidizing, the stone ball not a strike circle entire, tiny, the tendency is small. Strong spheroidizing ability, stable composition and reaction. Application Ferro Silicon Magnesium nodulizer ( FeSiMg )Used for nodular cast iron, adding hot metal can play a role in spheroidizing, desulfurization and outgassing. It can also improve the molten iron purity; generate compound insoluble in water with arsenic, zinc, tin, lead and other low melting point impurity. Standard Grade Chemical Composition (%) Mg Re Si Ca Al Ti Fe FeSiMg5Re2 4.0-6.0 1.0-3.0 38-44 2.0-3.0
Characteristics Ferro Silicon Barium ( FeSiBa ) is a kind of good deoxidizer and desulfurizer. 1. Deoxidization ability strong, Good molten steel flow, Completely solve the problem of the nodular casting nozzle. 2. Significantly improve the recovery rate of the silicon, manganese, etc. Reduce the addition amount of carbon powder. 3. The desulfurization effect is obvious, Shortening the period of steelmaking. Application 1.Wide range of application, Can part instead of deoxidizing agent in steelmaking, Eg: aluminum wire, silicon barium aluminum, ferro silicon aluminum, the calcium silicon wire, etc.2.Easy to use, simple operation, Donâ??t need to add any auxiliary equipment. Standard Grade Chemical Composition (%) BaSiAlC â?¥(Min)â?¤(Max) FeSi50Ba30305030.3 FeSi40Ba25254030.3 FeSi45Ba20204530.3 FeSi50Ba15155030.3 FeSi55Ba10105530.2 FeSi60Ba556020.2 FeSi65Ba226520.2 The specification,packaging and granular size can be produce according to customer demand.
Characteristics Rare Earth Ferro Silicon ( RE FeSi )adopts the one-stage process production and gets its form in secondary thin pouring. It also has the high Si content, high Re retrieving, easy to adjusting and other characteristics.The product is assembly compacted, with even chemical composition. It is with silver-gray appearance and metallic luster. Hard and easy to crush. Application Rare Earth Ferro Silicon ( RE FeSi ) is suitable to be used as the additive in steelmaking and iron-casting, or as the intermediate alloy of rare earth. It can also serve as the inoculant of gray casting iron, ductile casting iron and vermicular casting iron. It is the important additive in all kinds of inoculant, nodulizing and vermiculazing agent. Standard Grade Chemical Element (%) Re Si Ba Ca Al Ti Mn Content â?¤(Max) FeSiRe25 24.0-26.0 55-65 2.0 2.0 1.5 0.3 0.5 FeSiRe27 26.0-29.0 50-60 FeSiRe30-A 30.0-32.0 50-55 FeSiRe30-B 29.0-30.0 50-55 Size: 10-50mm; etc The specification,packaging and granular size can be produce according to customer demand.
Si: 40-50 % Ca: 10-20 % Mn: 10-20 % C: 1.0 % max. P: 0.05% max. S: 0.04% max. Fe: 15 % max. Al: 1.5% max.
Place of origin: guangdong, china (mainland) Brand name: laimeisi Model number: lms Application: fiberglass mesh cloth Weight: 158 gsm - 1740 gsm Surface treatment: silicon coated Width: 300~600mm, 300~600mm w Eave type: plain woven yarn type: c-glass Alkali content: alkali free Standing temperature: -40?~260? Hardness: 70shore Specific gravity: 1.6~2.3g/cm3 Size: 50m/roll Thickness: 0.2~3.0mm Flammability: ul94v-0 Continuous use temp: -40?~260? Rohs: pass Color: pink, blue, grey
Place of origin: guangdong, china (mainland) Brand name: laimeisi Model number: lms Application: fiberglass mesh cloth Weight: 158 gsm - 1740 gsm Surface treatment: silicon coated Width: 300~600mm, 300~600mm w Eave type: plain woven yarn type: c-glass Alkali content: alkali free Standing temperature: -40?~260? Hardness: 70shore Specific gravity: 1.6~2.3g/cm3 Size: 50m/roll Thickness: 0.2~3.0mm Flammability: ul94v-0 Continuous use temp: -40?~260? Rohs: pass Color: pink, blue, grey
Product specifications : silicon rubber band Rubber band, 1x1mm, dia 4.5cm, 100g, cmc-red Rubber band, 1x1mm, dia 7cm, 400g, cmc-red Rubber band, 1x3mm, dia12cm, 100g, cmc-amber Rubber band, 1x8mm, dia12cm, 100g, cmc-amber Quantity required : initially 10000 pieces Shipping term : fob
Addition cure silicon rubber for artificial stone products pplications: It mainly use for making molds for resin, stone, gypsum and cement product with medium size. Addition cure silicon rubber for artificial stone products Typical Datasheet : Item No Color Hardness (A°) Viscosity (CS) Tensile-strength( kgf /cm2 ) Tear-strength (kgf /cm2) Elongation-break(%) Mixing Ratio of silicone and catalyst Application(most for resin, stone, gypsum and cement product to make moulds) HY-E635 Translucent 35±2 8000±2000 =60 =13 =400 1:1 Addition cure silicon rubber for artificial stone products Points of attention: 1,Prone to poisoning, can not mix with condensation, ionic compounds containing N, S-, P, organic matter and of Sn, As, Hg, Ph., easy molding plastic poisoning, resulting in the phenomenon of not curing. 2,Comparing with Condensation cure silicone, Addition cure silicone's adhesive properties to be worse. 3,Addition cure silicone affect by temperature greatly when cured under room temperature. 4,Addition cure silicone is easy to poisoning, please clean the tools which are used for condensation silicone rubber, so that it can avoid poisoning. It’s fobidden to add the pigment or powder to addition cure silicone rubber arbitrarily,it’s easy to make the catalyst to be poisoning. 5,Addition cure silicone rubebr has two-component, the component A and component B, please pay attention to clean the component A containers before using for the component B, and vice versa 6,In order to avoid the hardness change, we should mix the component A and component B according to its mixing ratio strictly, no atter it’s 1 : 1 or 10 : 1.
